Potentiometric determination of p-chloranil and the kinetic study of its alkaline hydrolysis, using a chloranilate selective electrode

Two Ion-Selective Electrodes (ISEs), one commercial chloride ISE and one home-made chloranilate (Chl(2-)) ISE, were applied to study the alkaline hydrolysis of p-chloranil. This reaction proceeds through a very fast first step producing monochloranilate (Chl(-)) and chloride ions followed by a slow, rate determining step, producing chloranilate (Chl(2-)) and chloride ion. Kinetic equations specific for this reaction scheme, were derived to calculate reaction rate constants from E-t curves. The potentiometric selectivity coefficient K(pot) = 2.23 x 10(4) was determined for the response of the chloranilate electrode to Chl(-) anion and used for the kinetic calculations. The reaction rate constant for the slow step of the hydrolysis was found to be 0.227 M(-1) . sec(-1) at 25 degrees and the activation energy 1.56 x 10(4) Cal/mol. The total potential change following the completion of the first fast step is proportional to the log C of chloranil. Concentrations of chloranil 5-500 ppm can be determined with a precision of about 2%. This potentiometric method was evaluated for the determination of chloranil in fungicide preparations (Spergon) and the results obtained were compared with those of the official iodometric method. Good agreement was found.     

Determination of indium in standard rocks by neutron activation analysis

A rapid neutron activation method for the determination of indium in rocks, based on 54 min (116m)In, is described. The method has been applied to a series of geochemical standards including granite G-1 and diabase W-1. The precision is better than +/- 5% for samples containing more than 5 x 10(-10)g indium. Good agreement with previously published values for G-1 and W-1 has been obtained.     

Interference in the kinetic determination of ascorbic acid by sulphide and sulphite

The reduction of 2,6-dichlorophenolindophenol (DCPI) by sulphides and sulphites has been studied kinetically by the stopped-flow technique. The reaction is first-order with respect to each of the reactants. From the distribution diagrams for the species DH(+)(2), DH and D(-) for DCPI and H(2)Q, HQ(-) and Q(2-) for sulphides or sulphites, a mechanism is proposed which suggests partial reactions of all possible combinations of the reacting species at any pH. An equation for calculation of the second-order reaction rate constants k at any pH is derived, which gives k as a function of [H(+)], the partial reaction rate constants and the dissociation constants of DCPI and H(2)S or H(2)SO(3). Values of the overall reaction rate constants over a wide pH-range have been determined, together with values of k for all possible partial reactions. For particular pH-values the second-order reaction rate constant was determined by four different methods. Mean values of k = 251 +/- 1 and 240 +/- 1 l.mole(-1).sec(-1) were obtained for pH 3.15 and 4.17, respectively, for the DCPI-Na(2)S reaction and k = 137 +/- 1, 127 +/- 1 and 136 +/- 1 l.mole(-1).sec(-1) for pH 2.02, 4.25 and 5.10, respectively, for the DCPI-Na(2)SO(3) reaction. From the slopes of the linear Arrhenius plots activation energies of 6.6 +/- 0.2 and 4.0 +/- 0.1 kcal/mole for the DCPI-Na(2)S and DCPI-Na(2)SO(3) reactions, respectively were calculated. The effect of ionic strength on the reactions supports the proposed mechanism.     

H atom yields from the reactions of CN radicals with C2H2, C2H4, C3H6, trans-2-C4H8, and iso-C4H8

The kinetics and H atom channel yield at both 298 and 195 K have been determined for reactions of CN radicals with C2H2 (1.00+/-0.21, 0.97+/-0.20), C2H4 (0.96+/-0.032, 1.04+/-0.042), C3H6 (pressure dependent), iso-C4H8 (pressure dependent), and trans-2-C4H8 (0.039+/-0.019, 0.029+/-0.047) where the first figure in each bracket is the H atom yield at 298 K and the second is that at 195 K. The kinetics of all reactions were studied by monitoring both CN decay and H atom growth by laser-induced fluorescence at 357.7 and 121.6 nm, respectively. The results are in good agreement with previous studies where available. The rate coefficients for the reaction of CN with trans-2-butene and iso-butene have been measured at 298 and 195 K for the first time, and the rate coefficients are as follows: k298K=(2.93+/-0.23)x10(-10) cm3 molecule(-1) s(-1), k195K=(3.58+/-0.43)x10(-10) cm3 molecule(-1) s(-1) and k298K=(3.17+/-0.10)x10(-10) cm3 molecule(-1) s(-1), k195K=(4.32+/-0.35)x10(-10) cm3 molecule(-1) s(-1), respectively, where the errors represent a combination of statistical uncertainty (2sigma) and an estimate of possible systematic errors. A potential energy surface for the CN+C3H6 reaction has been constructed using G3X//UB3LYP electronic structure calculations identifying a number of reaction channels leading to either H, CH3, or HCN elimination following the formation of initial addition complexes. Results from the potential energy surface calculations have been used to run master equation calculations with the ratio of primary:secondary addition, the average amount of downward energy transferred in a collision DeltaEd, and the difference in barrier heights between H atom elimination and an H atom 1, 2 migration as variable parameters. Excellent agreement is obtained with the experimental 298 K H atom yields with the following parameter values: secondary addition complex formation equal to 80%, DeltaEd=145 cm(-1), and the barrier height for H atom elimination set 5 kJ mol(-1) lower than the barrier for migration. Finally, very low temperature master equation simulations using the best fit parameters have been carried out in an increased precision environment utilizing quad-double and double-double arithmetic to predict H and CH3 yields for the CN+C3H6 reaction at temperatures and pressures relevant to Titan. The H and CH3 yields predicted by the master equation have been parametrized in a simple equation for use in modeling.     

Flow injection amperometric detection of ascorbic acid using a Prussian Blue film-modified electrode

The PB film-modified electrode was used as an amperometric detector for flow injection analysis of ascorbic acid. The modified electrode detector showed good sensitivity, stability and reproducibility. The calibration curve for ascorbic acid was linear over the concentration range from 5.0x10(-6) to 1.0x10(-3) mol l(-1) with a slope of 19.9 mA mol(-1) per litre and a correlation coefficient of 0.999. The detection limit of this method was 2.49x10(-6) mol l(-1). The relative standard deviation of six replicate injections of 2.5x10(-4) mol l(-1) ascorbic acid was 2.5%. The results obtained for ascorbic acid determination in pharmaceutical products are in good agreement with those obtained by using the procedure involving the reaction between triiodide and ascorbic acid.     

Heterogeneous uptake of gaseous nitric acid on dolomite (CaMg(CO3)2) and calcite (CaCO3) particles: a Knudsen cell study using multiple, single, and fractional particle layers

In this study, the heterogeneous uptake of gaseous nitric acid on dolomite, CaMg(CO3)2, and calcite, CaCO3, particles under dry conditions at 296 K was investigated. A Knudsen cell reactor was used to measure heterogeneous uptake coefficients for these reactions. Several different experiments were performed including those on many, single, and fractional layers of particles. For experiments using multiple particle layers, the Knudsen cell data were modeled to take into account gas diffusion into the underlying layers of the sample. From this analysis, initial heterogeneous uptake coefficients, gamma(o,t), were determined to be (5 +/- 2) x 10(-4) and (2 +/- 1) x 10(-3), for dolomite and calcite, respectively, at a nitric acid concentration of 6.5 x 10(10) molecules cm(-3). For experiments that employed single or fractional particle layers, the initial heterogeneous uptake coefficient was analyzed using a recent method described in the literature. Values of the initial heterogeneous uptake coefficient using this analysis were in agreement with the above analysis and determined to be (7 +/- 4) x 10(-4) and (2 +/- 0.4) x 10(-3) for CaMg(CO3)2 and CaCO3, respectively. In addition, these results are compared to previous literature values.     

Theoretical Simulations of Kinetic Isotope Effects on Decarboxylation of 3-Carboxybenzisoxazole

Kinetic isotope effect values on the decarboxylation of 3-carboxybenzisoxazole have been computed using the second-order Kleinert's variational perturbation theory in the framework of Feynman's path integrals along with the potential energy surface obtained at the MP2/6-31+G(d) level. Good agreement with the experimental data was obtained, demonstrating that this novel computational approach for computing KIE values of organic reaction is a viable alternative to the traditional method employing the Bigeleisen equation and harmonic vibrational frequencies. Compared with the experimental measurements, consideration of anharmonicity and tunneling effects can significantly improve the calculated KIE values, reducing the root-mean-square deviation from 1.19 % for traditional method to 0.20 % for path-integral method.     

Thermal dissociation of SO3 at 1000-1400 K

The thermal dissociation of SO3 has been studied for the first time in the 1000-1400 K range. The experiments were conducted in a laminar flow reactor at atmospheric pressure, with nitrogen as the bath gas. On the basis of the flow reactor data, a rate constant for SO3 + N2 --> SO2 + O + N2 (R1b) of 5.7 x 10(17) exp(-40000/T) cm3/(mol s) is derived for the temperature range 1273-1348 K. The estimated uncertainty is a factor of 2. The rate constant corresponds to a value of the reverse reaction of k1 approximately 1.8 x 10(15) cm6 mol(-2) s(-1). The reaction is in the fall-off region under the investigated conditions. The temperature and pressure dependence of SO2 + O (+N2) was estimated from the extrapolation of low temperature results for the reaction, together with an estimated broadening parameter and the high-pressure limit determined recently by Naidoo, Goumri, and Marshall (Proc. Combust. Inst. 2005, 30, 1219-1225). The theoretical rate constant is in good agreement with the experimental results. The improved accuracy in k(1) allows a reassessment of the rate constant for SO3 + O --> SO2 + O2 (R2) based on the data of Smith, Tseregounis, and Wang (Int. J. Chem. Kinet. 1982, 14, 679-697), who conducted experiments on a low-pressure CO/O2/Ar flame doped with SO2. At the location in the flame where the net SO3 formation rate is zero, k2 = k1[SO2][M]/[SO3]. A value of 6.9 x 10(10) cm3 mol(-1) s(-1) is obtained for k2 at 1269 K with an uncertainty a factor of 3. A recommended rate constant k2 = 7.8 x 10(11) exp(-3065/T) cm3 mol(-1) s(-1) is consistent with other flame results as well as the present flow reactor data.     

From alcohols to sugars-how does the reactivity of alpha-hydroxyalkyl radicals change with structure? A quantitative examination by pulse radiolysis

Rate constants are reported for the 1-electron reduction of the azo dye Orange II in water (pH 7.0) by 10 different alpha-hydroxy radicals. The radicals were created by pulse radiolysis of aqueous solutions of the corresponding alcohol/sugar. The rate constants varied from 1 x 10(8) to 2.7 x 10(9) mol(-1) dm(3) s(-1) and radicals with beta-hydroxy groups had the lowest rate constant. The reaction was found to be controlled by the reduction potentials of the radicals, with steric influences having little effects. Good fits of the data were obtained using the Marcus equation with lambda =140 kJ/mol.     

Terephthalic acid esterification kinetics: 2-(2-methoxyethoxy)ethyl terephthalates

The process of esterification of terephthalic acid is characterized by a mechanism that involves three equilibrium reactions. Two are esterification-hydrolysis equilibria entailing the reactions of the two terephthalic acid carboxyl groups with alcoholic hydroxyl groups, whereas the third one is a transesterification-acidolysis equilibrium that is concerned with the reaction between two terminal terephthalic acid moieties. The products of these three interrelated equilibria are terephthalic acid, its monoester and diester, the particular alcohol, and water. The alcohol used in the present study was 2-(2-methoxyethoxy)ethanol. Equilibrium constants and rate constants were developed from experimental data obtained at 230°C. The esterification-hydrolysis reactions were found to be catalyzed by carboxyl groups, and the rate of transesterification was found to be a function of the terephthalic acid concentration. With the constants developed, the system of nonlinear differential equations, as derived from the mechanism postulated, was integrated numerically using the Runge-Kutta method. Good agreement between calculated and experimental values was observed.     

Immobilization of lactate oxidase in a poly(vinyl alcohol) matrix on platinized graphite electrodes by chemical cross-linking with isocyanate

A new method for development of an electrochemical sensor based on lactate oxidase is dedbed. Platinized spectroscopic-grade graphite electrodes were modified by chemically cross-linking l-lactate oxidase from Pediococcus species into a poly(vinyl alcohol) network through reaction with a tri-isocyanate. The immobilized enzyme exhibits high activity and long-term stability. The sensor provides a linear response to l-lactate over a concentration range of 2 x 10(-5)-4 x 10(-3)M and a sensitivity of 1.71 muA.1. mmole(-1). The response time of the sensor is 10-45 sec and the detection limit is 10muM. Stable response to the substrate was obtained over a period of 3 months. The new sensor was also used for the analysis of some dairy products without any special pretreatment.     

Flow injection analysis using carbon film resistor electrodes for amperometric determination of ambroxol

Flow injection analysis (FIA) using a carbon film sensor for amperometric detection was explored for ambroxol analysis in pharmaceutical formulations. The specially designed flow cell designed in the lab generated sharp and reproducible current peaks, with a wide linear dynamic range from 5x10(-7) to 3.5x10(-4) mol L(-1), in 0.1 mol L(-1) sulfuric acid electrolyte, as well as high sensitivity, 0.110 Amol(-1) L cm(-2) at the optimized flow rate. A detection limit of 7.6x10(-8) mol L(-1) and a sampling frequency of 50 determinations per hour were achieved, employing injected volumes of 100 microL and a flow rate of 2.0 mL min(-1). The repeatability, expressed as R.S.D. for successive and alternated injections of 6.0x10(-6) and 6.0x10(-5) mol L(-1) ambroxol solutions, was 3.0 and 1.5%, respectively, without any noticeable memory effect between injections. The proposed method was applied to the analysis of ambroxol in pharmaceutical samples and the results obtained were compared with UV spectrophotometric and acid-base titrimetric methods. Good agreement between the results utilizing the three methods and the labeled values was achieved, corroborating the good performance of the proposed electrochemical methodology for ambroxol analysis.     

Malonic acid concentration as a control parameter in the kinetic analysis of the Belousov-Zhabotinsky reaction under batch conditions

The influence of the initial malonic acid concentration [MA]0 (8.00 x 10(-3) < or = [MA]0 < or = 4.30 x 10(-2) mol dm(-3)) in the presence of bromate (6.20 x 10(-2) mol dm(-3)), bromide (1.50 x 10(-5) mol dm(-3)), sulfuric acid (1.00 mol dm(-3)) and cerium sulfate (2.50 x 10(-3) mol dm(-3)) on the dynamics and the kinetics of the Belousov-Zhabotinsky (BZ) reactions was examined under batch conditions at 30.0 degrees C. The kinetics of the BZ reaction was analyzed by the earlier proposed method convenient for the examinations of the oscillatory reactions. In the defined region of parameters where oscillograms with only large-amplitude relaxation oscillations appeared, the pseudo-first order of the overall malonic acid decomposition with a corresponding rate constant of 2.14 x 10(-2) min(-1) was established. The numerical results on the dynamics and kinetics of the BZ reaction, carried out by the known skeleton model including the Br2O species, were in good agreement with the experimental ones. The already found saddle node infinite period (SNIPER) bifurcation point in transition from a stable quasi-steady state to periodic orbits and vice versa is confirmed by both experimental and numerical investigations of the system under consideration. Namely, the large-amplitude relaxation oscillations with increasing periods between oscillations in approaching the bifurcation points at the beginning and the end of the oscillatory domain, together with excitability of the stable quasi-steady states in their vicinity are obtained.     

Kinetics of the CH2Cl + CH3 and CHCl2 + CH3 radical-radical reactions

The CH2Cl + CH3 (1) and CHCl2 + CH3 (2) cross-radical reactions were studied by laser photolysis/photoionization mass spectroscopy. Overall rate constants were obtained in direct real-time experiments in the temperature region 301-800 K and bath gas (helium) density (6-12) x 10(16) atom cm(-3). The observed rate constant of reaction 1 can be represented by an Arrhenius expression k1 = 3.93 x 10(-11) exp(91 K/T) cm3 molecule(-1) s(-1) (+/-25%) or as an average temperature-independent value of k1= (4.8 +/- 0.7) x 10(-11) cm3 molecule(-1) s(-1). The rate constant of reaction 2 can be expressed as k2= 1.66 x 10(-11) exp(359 K/T) cm3 molecule(-1) s(-1) (+/-25%). C2H4 and C2H3Cl were detected as the primary products of reactions 1 and 2, respectively. The experimental values of the rate constant are in reasonable agreement with the prediction based on the "geometric mean rule." A separate experimental attempt to determine the rate constants of the high-temperature CH2Cl + O2 (10) and CHCl2 + O2 (11) reaction resulted in an upper limit of 1.2 x 10(-16) cm(3) molecule(-1) s(-1) for k10 and k11 at 800 K.     

Experimental and theoretical studies of the reaction of the OH radical with alkyl sulfides: 1. Direct observations of the formation of the OH-DMS adduct-pressure dependence of the forward rate of addition and development of a predictive expression at low temperature

A pulsed laser photolysis-pulsed laser-induced fluorescence (PLP-PLIF) system was employed to study the kinetics and mechanisms of reactions (1) OH + h6-DMS --> products and (2) OH + d6-DMS --> products. We report direct observations of the rate coefficients for the formation and dissociation of the h6-OHDMS and d6-OHDMS adducts over the pressure range 50-650 Torr and between 240 and 245 K, together with measurements of the oxygen dependence of the effective rate coefficients for reactions 1 and 2 under similar conditions. The effective rate coefficients increased as a function of O2 concentration reaching their limiting values in each case. The values of the adduct formation rate, obtained from the O2 dependencies, were in excellent agreement with values determined from direct observation of adduct equilibration in N2. OH regeneration is insignificant. The rate coefficients for the formation of the adduct isotopomers showed slight differences in their falloff behavior and do not approach the high-pressure limit in either case. The equilibrium constants obtained show no dependence on isotopomer and are in good agreement with previous work. A "second-law" analysis of the temperature dependence of the equilibrium constant gives an adduct bond strength (DeltaH degrees =-10.9 +/- 1.0 kcal mol(-1)), also in good agreement with previously reported values. Using the entropy calculated from the ab initio vibrational frequencies, we obtain a "third-law" value for the reaction enthalpy at 240 K, DeltaH(240K) degrees = -10.5 kcal mol(-1) in good agreement with the other approach. The rate coefficient for the reactions of the adducts with O2 was obtained from an analysis of the O2 dependence and was determined to be 6.3 +/- 1.2 x 10(-13) cm3 molecule(-1) s(-1), with no dependence on pressure or isotopomer. The pressure and temperature dependence for all of the elementary processes in the initial steps of the dimethylsulfide (DMS) oxidation mechanism have been characterized in the range 238-245 K, allowing the formulation of an expression which can be used to calculate the effective rate coefficient for reaction 1 at any pressure and oxygen concentration. The expression can calculate the effective rate coefficient for reaction 1 to +/- 40% over the range 220-260 K, with the largest errors at the extremes of this range. Gaussian 03 has been used to calculate the structure of the OH-DMS adduct and its deuterated isotopomer. We find similar bound structures for both isotopomers. The calculated enthalpies of formation of the adducts are lower than the experimentally determined values.     

Controlling ionic conductivity in lipid polyelectrolyte composite capsules by cholesterol

The effect of cholesterol on the formation and properties of bilayer lipid membranes deposited on polyelectrolyte multilayered capsules was studied. The permeability of lipid/cholesterol coated capsules for NaCl was derived from osmotic response experiments and ranged from 1.45 x 10(-8) to 2.9 x 10(-8) m.s(-1), which corresponds to a lipid layer conductivity of (0.7-1.4) x 10(-8) S.m(-1). These conductivity values were in good agreement with the value of 0.8 x 10(-8) S.m(-1) obtained by electrorotation and were by 3 orders of magnitude lower than those found earlier for lipid layers on polyelectrolyte capsules in the absence of cholesterol.     

The role of geometry on regioselectivity and rate of fluorination of fluorene and diphenylmethane with Selectfluor F-TEDA-BF4

Diphenylmethane and fluorene were used as target molecules in an investigation of the effect of the geometry of aromatic molecules on the regioselectivity and rate of fluorination with 1-chloromethyl-4-fluoro-1,4-diazoniabicyclo[2.2.2]octane bis(tetrafluoroborate) (Selectfluor F-TEDA-BF4). In acetonitrile at 80 degrees C ring fluorination of diphenylmethane was accompanied by oxidation of the saturated carbon atom, while in trifluoroacetic acid only ring fluorination with an ortho-para regioselectivity of 1.8:1 was observed. Fluorene was converted in acetonitrile as well as in trifluoroacetic acid into 2- and 4-fluoro substituted products in the relative ratio of 2:1 and 1.2:1, respectively. The reactions in acetonitrile obey a simple rate equation: v = d[F-TEDA]/dt = k2 x [F-TEDA] x [Substrate] and the second order rate constants for the reactions in acetonitrile at 65 degrees C were determined; values of 0.6 x 10(-4) M-1 s-1 for diphenylmethane and 35.5 x 10(-4) M-1 s-1 for fluorene were obtained. The reaction rates for the various functionalisations of fluorene relative to those for diphenylmethane were found to be considerably influenced by the type of functionalisation. Relative rate factors (k(rel) = k2(fluorene)/k2(diphenylmethane)) with values between 59 for fluorination and 712 for chlorination were determined, while the corresponding data for the biphenyl/diphenylmethane pair were only slightly dependent on the type of functionalisation. A reaction pathway involving electron transfer, thus forming cation radical intermediates, was proposed as the main process in the case of fluorination of fluorene with F-TEDA-BF4.     

Aminoalkyl radicals: direct observation and reactivity toward oxygen, 2,2,6,6-tetramethylpiperidine-N-oxyl, and methyl acrylate

The reactivity of 11 aminoalkyl radicals toward different additives [oxygen, 2,2,6,6-tetramethylpiperidine-N-oxyl (TEMPO), and methyl acrylate (MA)] has been investigated through laser flash photolysis and quantum mechanical calculations. The transient absorption spectra of the radicals were recorded: good agreement was found with the spectra calculated by using quantum mechanical calculations. All the interaction rate constants were measured. A large range of values are obtained: (0.04-3) x 10(9) M(-1) s(-1) for O2, (0.002-5) x 10(8) M(-1) s(-1) for TEMPO, and (<0.004-2) x 10(7) M(-1) s(-1) for MA. Generation of the decarboxylated aminoalkyl radical derived from N-phenylglycine was unambiguously demonstrated. It was clearly found that both the addition to oxygen and the recombination with TEMPO were strongly governed by the reaction exothermicity. On the other hand, both polar and enthalpy factors have a large influence on the rate constants of the addition reaction to the acrylate unit, which were ranging over at least 4 orders of magnitude. This paper provides a set of new data to characterize the structure/reactivity relationships of aminoalkyl radicals.     

Experimental and theoretical studies of the kinetics of the reactions of OH and OD with 2-methyl-3-buten-2-ol between 300 and 415 K at low pressure

The rate constants for the reactions of OH and OD with 2-methyl-3-buten-2-ol (MBO) have been measured at 2, 3, and 5 Torr total pressure over the temperature range 300-415 K using a discharge-flow system coupled with laser induced fluorescence detection of OH. The measured rate constants at room temperature and 5 Torr for the OH + MBO reaction in the presence of O2 and the OD + MBO reaction are (6.32 +/- 0.27) and (6.61 +/- 0.66) x 10(-11) cm3 molecule(-1) s(-1), respectively, in agreement with previous measurements at higher pressures. However, the rate constants begin to show a pressure dependence at temperatures above 335 K. An Arrhenius expression of k0 = (2.5 +/- 7.4) x 10(-32) exp[(4150 +/- 1150)/T] cm6 molecule(-2) s(-1) was obtained for the low-pressure-limiting rate constant for the OH + MBO reaction in the presence of oxygen. Theoretical calculations of the energetics of the OH + MBO reaction suggest that the stability of the different HO-MBO adducts are similar, with predicted stabilization energies between 27.0 and 33.4 kcal mol(-1) relative to the reactants, with OH addition to the internal carbon predicted to be 1-4 kcal mol(-1) more stable than addition to the terminal carbon. These stabilization energies result in estimated termolecular rate constants for the OH + MBO reaction using simplified calculations based on RRKM theory that are in reasonable agreement with the experimental values.     

I(+1) transfer from diiodomalonic acid to malonic acid and a complete inhibition of the CO and CO2 evolution in the Briggs-Rauscher reaction by resorcinol

A recent report on an intense CO 2 and CO evolution in the Briggs-Rauscher (BR) reaction revealed that iodination of malonic acid (MA) is not the only important organic reaction in the classical BR oscillator. To disclose the source of the gas evolution, iodomalonic (IMA) and diiodomalonic (I2MA) acids were prepared by iodinating MA with nascent iodine in a semibatch reactor. The nascent iodine was generated by an iodide inflow into the reactor, which contained a mixture of MA and acidic iodate. Some CO2 and a minor CO production was observed during these iodinations. It was found that in an aqueous acidic medium the produced I2MA is not stable but decomposes slowly to diiodoacetic acid and CO2. The first-order rate constant of the I 2MA decarboxylation at 20 degrees C was found to be k1 = 9 x 10(-5) s(-1), which is rather close to the rate constant of the analogous decarboxylation of dibromomalonic acid under similar conditions (7 x 10(-5)s(-1)). From the rate of the CO2 evolution, the I2MA concentration can be calculated in a MA-IMA-I2MA mixture as only I2MA decarboxylates spontaneously but MA and IMA are stable. Following CO2 evolution rates, it was proven that I2MA can react with MA in the reversible reaction I2MA + MA <--> 2 IMA. The equilibrium constant of this reaction was calculated as K = 380 together with the rate constants of the forward k 2 = 6.2 x 10 (-2) M (-1)s(-1) and backward k-2 = 1.6 x 10(-4) M(-1)s(-1) reactions. The probable mechanism of the reaction is I(+1) transfer from I2MA to MA. The presence of I(+1) in a I2MA solution is demonstrated by its reduction with ascorbic acid. To estimate the fraction of CO2 coming from the decarboxylation of I2MA in an oscillatory BR reaction, the oscillations were inhibited by resorcinol. Unexpectedly, all CO2 and CO evolution was interrupted for more than one hour after injecting a small amount of resorcinol (10(-5) M initial concentration in the reactor). Finally, some implications of the newly found I(+1) transfer reactions and the surprisingly effective inhibition by resorcinol regarding the mechanism of the oscillatory BR reaction are discussed. The latter is explained by the ability of resorcinol to scavenge free radicals including iodine atoms without producing iodide ions.