Concentration of chlorophenols in water with sodium dodecylsulfate-gamma-alumina admicelles for high-performance liquid chromatographic analysis

Chlorophenols in water were sorbed onto sodium dodecylsulfate (SDS)-alumina (gamma-form) admicelles. The extent of sorption increased with increasing amount of SDS and decreasing solution pH. Conditions for good recovery were obtained when 100 mg SDS and 1.5 g alumina was used at pH 2. However, the yield decreased with a further increase in the SDS concentration due to the formation of normal SDS micelles. The extent of sorption also increased with increasing hydrophobicity of the chlorophenol, indicating that hydrophobic interactions predominate for the collection of analytes. When a cartridge column filled with admicelles was used, >90% of tetrachlorophenol and pentachlorophenol in 200 ml of water samples were rapidly recovered. The sorbed analytes were eluted with 1 ml acetonitrile. The accuracy and precision of the present method were demonstrated for the HPLC analysis with ultraviolet (290 nm) detection of microg l(-1) levels of tetrachlorophenol and pentachlorophenol in river water samples.     

Preconcentration and Determination of Trace Nickel Using 1-(2-Pyridylazo)-2-Naphtol (PAN) Immobilized on Surfactant-Coated Alumina

A microcolumn of alumina modified with sodium dodecyl sulfate (SDS) and 1-(2-pyridylazo)-2-naphthol (PAN) was prepared for the preconcentration of trace nickel from water samples for a flame atomic absorption spectrometry (FAAS) determination. Under optimized conditions (pH = 4.0; flow rate, 5 mL min^–1) nickel (II) was retained on the column. The nickel collected on the column was eluted with 5 mL of 0.5 M nitric acid. Recovery was greater than 96.7%. A concentration factor of 300 can be achieved by passing 1500 mL of sample through the microcolumn. The relative standard deviation (ten replicate analyses) at the 40 ng mL^–1 level for nickel was 2.4%, and the corresponding limit of detection (based on 3) was 0.06 ng mL^–1. The method was applied to the determination of Ni in waste and mineral waters.     

Preconcentration and Spectrophotometric Determination of Chromium (VI) and Total Chromium in Drinking Water by the Sorption of Chromium Diphenylcarbazone with Surfactant Coated Alumina

Abstract

A simple and inexpensive method for determining chromium (VI) in drinking water by spectrophotometry after preconcentration with sodium dodecyl sulphate (SDS) coated alumina column is described. Chromium(VI) is reacted with diphenylcarbazide (DPC) and the Cr-DPC complex is quantitatively adsorbed onto a SDS coated alumina column from 800 ml of sample solution. The complex is then eluted with a 8 ml mixture of methanol, acetone and hydrochloric acid and determined by spectrophotometry. Total chromium can be determined after oxidation of chromium (III) to chromium (VI) by KMnO₄. The relative standard deviation (10 replicate analyses) at the 10 μg l^?1 of chromium (VI) and 10 μg l^?1 of total chromium were 3.5% and 3.4% and corresponding limits of detection (based on 3 σ) were 0.040 μg l^?1 and 0.033 μg l^?1, respectively.     

Hemimicelle-based solid-phase extraction of estrogens from environmental water samples

Hemimicelles and admicelles of sodium dodecyl sulfate (SDS) on alumina and cetyltrimethyl ammonium bromide (CTAB) on silica were evaluated for the concentration and purification of the priority estrogens estrone (E(1)), 17beta-estradiol (E(2)) and ethynylestradiol (EE(2)) from sewage and river samples. Retention was based on analyte-sorbent hydrophobic and cation-pi interactions. Parameters affecting the SPE of estrogens on both types of sorbents were comparatively investigated. Adsolubilization was quantitative for SDS hemimicelles/admicelles and CTAB admicelles. SDS hemimicelle-coated alumina was the sorbent selected on the basis of the lower elution volume required and the higher sample flow rate allowed. Combination of estrogen adsolubilization-based SPE with liquid chromatography-diode array/fluorescence detection permitted the quantification of the target compounds with detection limits ranging from 20 to 100 ng l(-1). The relative standard deviation ranged from 3 to 8%. The approach developed was applied to the determination of estrogens in raw and treated sewage and river samples. The recovery found for estrogens in these environmental matrices was between 85 and 105%.     

Determination of alkylphenols and alkylphenol carboxylates in wastewater and river samples by hemimicelle-based extraction and liquid chromatography-ion trap mass spectrometry

Sodium dodecyl sulfate (SDS)-coated alumina and cetylpyridinium chloride (CPC)-coated silica were investigated as new sorbents for the concentration of alkylphenol polyethoxylate (APE) biodegradation products from wastewater and river water samples. Octylphenol (OP), nonylphenol (NP), octylphenol carboxylic acid (OPC) and nonylphenol carboxylic acid (NPC) were quantitatively retained on both supramolecular sorbents on the basis of the formation of mixed hemimicelles and admicelles. SDS hemimicelles-based SPE was proposed for the extraction/concentration of the target compounds prior to their separation and quantitation by liquid chromatography/electrospray ionization in negative mode, ion trap mass spectrometry. No clean-up steps or evaporation of the eluent were required. The recovery of APE metabolites from sewage and river water ranged between 87 and 100%. Concentration factors of about 500, using sample volumes of 1 l, were achieved. Detection limits were between 75 and 193 ng/l. The approach developed was applied to the determination of alklylphenols and alkylphenol carboxylic acids in raw and treated sewage and river samples. The concentrations of APE metabolites found ranged between 0.8 and 78 microg/l.     

Reexamination of 2-Naphthol Adsolubilization on Alumina with Sodium Dodecyl Sulfate Adsorption

Adsolubilization behavior of 2-naphthol on alumina with adsorption of sodium dodecyl sulfate (SDS) at pH 3.5 in the presence of 10 mmol dm(-3) NaCl was reexamined. The adsolubilized amount of 2-naphthol increased sharply and reached a maximum, then decreased with SDS concentration. The decrement of the adsolubilized amount began below the critical micelle concentration of SDS. From the dispersion state of the alumina suspension and the SDS adsorption isotherm, it is demonstrated that the decrement of adsolubilization of 2-naphthol is not due to the partition of 2-naphthol between the SDS adsorbed layer and SDS micelles, but is due to the difference of SDS adsorption states such as monolayers and admicelles. Copyright 2000 Academic Press.     

油菜籽中主要硫甙的分离提纯

用柱色谱方法从甘蓝型油菜籽中分离提纯了1-硫［(1Z)-3-羟基-1-［(磺酸基)亚氨基］-4-戊烯基］-1-硫代-β-D-葡萄糖钾盐(progoitrin)。用甲醇溶液提取菜籽中的硫甙,得到粗提物;粗提物经酸性氧化铝色谱柱与反相C18硅胶柱进一步分离提纯,得到纯品。对纯品进行紫外光谱、红外光谱、核磁共振氢谱、质谱和元素分析,测得的数据与文献值相符。用高效液相色谱测得硫甙提取物的纯度为99%。该方法操作简便,得到的硫甙样品纯度高,是一种有价值的硫甙提取方法,具有良好的应用前景。     

Separation and preconcentration of trace quantities of copper ion using modified alumina nanoparticles, and its determination by flame atomic absorption spectrometry

We report on a sensitive, reliable and relatively fast method for separation, preconcentration and determination of trace quantities of copper(II) ion. It is making use of nanometer-sized γ-alumina nanoparticles modified with sodium dodecyl sulfate (SDS). The adsorptive potential was assessed via a Langmuir isotherm and the maximal sorption capacity was found to be 138 mg g^-1. The effects of pH values, amount of ligand, flow rate, type of eluting agent, volume of eluent, and the volume of sample were examined. The effects of interfering ions on the recovery of the analyte were also investigated. Copper ion was then determined by flame atomic absorption spectrometry. The relative standard deviation for five replicate determinations (at 50 μg L^?1 of copper) is 3.3%. The detection limit (at 3 s) is 2.5 μg L^?1. This method was validated with a certified reference material of oyster tissue (NIST SRM 1566b) and the results coincided well with the certified values. The procedure was successfully applied to the determination of Cu in water and food samples.

Trace enrichment and measurement of platinum by flow injection inductively coupled plasma mass spectrometry

A flow injection system incorporating an alumina microcolumn has been coupled to inductively coupled plasma mass spectrometry (ICP-MS) for on-line preconcentration and determination of platinum (IV) in natural waters. Depending on the nature of the sample, a nominal preconcentration factor of up to 600 can be achieved by eluting with 50l of 2 mol/l NH₄OH. The limit of detection after a 5 min preconcentration time was 4 ngl^-1, with a relative standard deviation of 4% (100 ngl^-1 working solution). The proposed method was assessed for the determination of platinum (IV) in natural waters, motor car exhaust and some common analytical reagents.     

Distribution of hexavalent Cr species across the clay mineral surface-water interface

The adsorption isotherms of Cr(VI) on kaolinite, montmorillonite, and alumina were adequately treated with Langmuir model showing behavior characteristic of single-layer adsorption. The efficiency of the adsorbents in removing Cr(VI) from water follows the order alumina > kaolinite > montmorillonite > silica. Speciation studies indicate that hydrogen chromate ions were the major adsorbed species and simultaneous adsorption of dichromate ion occurred at concentrations greater than approximately 10(-3) mol L(-1). It is most probable that the mechanism of adsorption of the hydrogen chromate ion at the surface of alumina is predominantly electrostatic adsorption, with outer sphere complex formation.     

Comparison of surfactant-assisted shotgun methods using acid-labile surfactants and sodium dodecyl sulfate for membrane proteome analysis

Three surfactant-assisted shotgun methods using acid labile surfactants, sodium-3-[(2-methyl-2-undecyl-1,3-dioxolan-4-yl)-methoxyl]-1-propanesulfonate (RapiGest) and 3-[3-(1,1-bisalkyloxyethyl)pyridin-1-yl]propane-1-sulfonate (PPS), and sodium dodecyl sulfate (SDS) were investigated for their applicability to membrane proteome analysis. It is shown that RapiGest is a preferred reagent for handling membrane proteomes of Escherichia coli and MCF7 cells for liquid chromatography tandem mass spectrometry (LC MS/MS) analysis of tryptic digests. The RapiGest method allowed identification of more peptides and proteins than the SDS and PPS methods and there was no apparent bias for the type of peptides and proteins identified by the RapiGest and SDS methods, while a slightly higher proportion of hydrophilic peptides and proteins were identified by the PPS method. The performance of the SDS and PPS methods is similar in terms of the numbers of peptides and proteins identified. Since the SDS method required the removal of SDS using a technique such as strong-cation exchange (SCX), we further investigated the effect of SCX on sample loss through analyzing the digest of an enriched E. coli membrane fraction as well as a standard protein, bovine serum albumin (BSA). The results showed that extensive sample loss (as much as 62%) was encountered during the SCX cleaning step. We then applied the RapiGest method in combination with two-dimensional LC MS/MS to characterize the E. coli membrane proteome. In total, 1626 unique proteins (5799 unique peptides) were identified with a peptide false discovery rate of 2.4%. About 60% of the identified proteins with known cellular locations were found to be membrane proteins. Among them, about 75% were integral membrane proteins. This work represents one of the most comprehensive profiles of E. coli membrane proteome generated by a proteomic technique.     

Spectrophotometric determination of Sb(III) in Sb(III)/Sb(V) binary mixtures using sodium dodecylsulfate/nonylphenoxy polyethoxyethanol mixed micellar media

Different micellar media had different effects on the absorption spectra of the complexes of bromopyrogallol red with Sb(III) and Sb(V). The mixed micellar medium composed of 0.7 ml of 0.2% sodium dodecylsulfate (SDS) and 0.3 ml of 2% nonylphenoxypolyethoxyethanol (OP) at 80 degrees C could be used for the sensitive determination of Sb(III) in Sb(III)/Sb(V) binary mixtures. Under the optimal conditions, Beer's Law was obeyed over the range 0.1-2.3 mug ml(-1) Sb(III) with molar absorptivity at 538 nm being 4.8 x 10(4) l mol(-1) cm(-1) and detection limit 0.04 mug ml(-1). For 10 mug Sb(III), more than 100 mug Sb(V) could be tolerated (error < 3%) in the presence of SDS/OP micellar medium as compared with 0.1 mug Sb(V) in the absence of SDS/OP micellar medium. In addition, the sensitivity of Sb(III) in the micellar medium was much higher than that in pure water medium. As compared with conventional extraction spectrometry, the proposed method produced a reproducible result. It did not need the conversion of Sb(III) to Sb(V) and a time-consuming extraction process. A detailed discussion on the selection of surfactants, the effect of temperature, and the role played by the mixed surfactants were also made.     

Detection of coexisting protein conformations in capillary zone electrophoresis subsequent to transient contact with sodium dodecyl sulfate solutions

Non-native conformations of proteins were generated by temporary contact with aqueous solutions of sodium dodecyl sulfate (SDS) and separated from the native state with capillary zone electrophoresis (CZE) in alkaline borate buffer deficient of SDS. Nine proteins at concentrations of 2.0 or 3.0 mg.L(-1) were compared in terms of their susceptibility to SDS. For superoxide dismutase and ferritin the tendency of unfolding was modest with < 25% of the protein being transformed to the non-native state at 10 mmol.L(-1) SDS. Highest susceptibility was observed for albumin, myoglobin (Mb), and hemoglobin with > 75% in the non-native state even at 2.0 mmol.L(-1) SDS. The influence of varying SDS concentrations on the conformational state of Mb was tested. Increasing the SDS concentration, circular dichroism revealed a reduction in alpha-helix, an increase in random coil, and an introduction of beta-sheet, which is absent in native structure. Modifications in the secondary structure were in agreement with distinct changes in the shape of the non-native Mb peak in CZE and make a gradual unfolding/refolding process with several coexisting molten globules instead of two-state transition of conformations most plausible for Mb. CZE was found to contribute to a further understanding of holo-Mb transformation towards a population of non-native conformations (i) by means of calculated peak area ratios of native to non-native states, which showed sigmoid transition, (ii) by detecting the release of the prosthetic heme group, and (iii) by changes in the effective electrophoretic mobility of the Mb-SDS peaks. Reconstituted holo-Mb forms differed in the Soret band around 410 nm, indicating diversity in the conformation of the heme pocket.     

Proteomic Profiling and the Predicted Interactome of Host Proteins in Compatible and Incompatible Interactions Between Soybean and <Emphasis Type="Italic">Fusarium virguliforme</Emphasis>

Sudden death syndrome (SDS) is a complex of two diseases of soybean (Glycine max), caused by the soil borne pathogenic fungus Fusarium virguliforme. The root rot and leaf scorch diseases both result in significant yield losses worldwide. Partial SDS resistance has been demonstrated in multiple soybean cultivars. This study aimed to highlight proteomic changes in soybean roots by identifying proteins which are differentially expressed in near isogenic lines (NILs) contrasting at the Rhg1/Rfs2 locus for partial resistance or susceptibility to SDS. Two-dimensional gel electrophoresis resolved approximately 1000 spots on each gel; 12 spots with a significant (P < 0.05) difference in abundance of 1.5-fold or more were picked, trypsin-digested, and analyzed using quadruple time-of-flight tandem mass spectrometry. Several spots contained more than one protein, so that 18 distinct proteins were identified overall. A functional analysis performed to categorize the proteins depicted that the major pathways altered by fungal infection include disease resistance, stress tolerance, and metabolism. This is the first report which identifies proteins whose abundances are altered in response to fungal infection leading to SDS. The results provide valuable information about SDS resistance in soybean plants, and plant partial resistance responses in general. More importantly, several of the identified proteins could be good candidates for the development of SDS-resistant soybean plants.     

Removal of sodium dodecyl sulfate from protein samples prior to matrix-assisted laser desorption/ionization mass spectrometry

Sodium dodecyl sulfate (SDS) is widely used for protein solubilization and for separation of proteins by SDS polyacrylamide gel electrophoresis (SDS-PAGE). However, SDS interferes with other techniques used for characterization of proteins, such as mass spectrometry (MS) and amino acid sequencing. In this paper, we have compared three procedures to remove SDS from proteins, including chloroform/methanol/water extraction (C/M/W), cold acetone extraction and desalting columns, in order to find a rapid and reproducible procedure that provides sufficient reduction of SDS and high recovery rates for proteins prior to matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS). A 1000-fold reduction of SDS concentration and a protein recovery at approximately 50% were obtained with the C/M/W procedure. The cold acetone procedure gave a 100-fold reduction of SDS and a protein recovery of approximately 80%. By using desalting columns, the removal of SDS was 100-fold, with a protein recovery of nearly 50%. Both the C/M/W and the cold acetone methods provided sufficient reduction of SDS, high recovery rates of protein and allowed the acquisition of MALDI spectra. The use of n-octyl-beta-D-glucopyranoside in the protein sample preparation enhanced the MALDI signal for protein samples containing more than 2 10(-4)% SDS, after the C/M/W extraction. Following the cold acetone procedure, the use of n-octylglucoside was found to be necessary in order to obtain spectra, but they were of lower quality than those obtained with the C/M/W method, probably due to higher residual amounts of SDS.     

Chromium speciation by a surfactant-coated alumina microcolumn using electrothermal atomic absorption spectrometry

A simple and convenient method has been developed for the speciation of chromium(III) and chromium(VI) in aqueous solutions using a sodium dodecyl sulphate coated alumina micro-column (1.5 cm x 5 mm i.d.) and graphite furnace-atomic absorption spectrometry (GF-AAS). Under the optimized conditions (pH 0.6, adjusted with hydrochloric acid; flow rate, 1 ml min(-1)) chromium(VI) is retained on the column and chromium(III) is collected and determined by GF-AAS. Total chromium is directly determined by GF-AAS and chromium(VI) is calculated by difference. The relative standard deviations (10 replicate analyses) at the 20 mug l(-1) level for chromium(III) and chromium(VI) and at the 40 mug l(-1) level for total chromium were 1.4%, 3.6% and 1.8%, and the corresponding limits of detection (based on 3sigma) were 0.57 mug ml(-1), 0.61 mug ml(-1) and 0.35 mug l(-1) respectively. No large interference effects have been observed from other investigated species and the method has been successfully applied to a range of water samples.     

Determination of Trace Lithium in Uranium Compounds by Adsorption on Activated Alumina Using a Micro-column Method

A novel method using a micro-column packed with active alumina as solid phase was proposed for separation of trace lithium from uranium compounds prior to determination. The method is based on a preliminary chromatographic separation of the total amount of uranium. This separation involves passing the solution containing sodium carbonate through active alumina and then eluting the trace lithium retained by the solid phase with a solution of sulfuric acid. Two modes, off-line and on-line micro-column preconcentration, were performed. In conjunction with atomic absorption spectrometry, this on-line preconcentration technique allows a determination of lithium at 10(-9) level. Both off-line and on-line mode operation conditions were investigated in separation and determination of trace lithium by micro-column method (length of column bed, flow rate, etc.). The adsorption capacity of activated alumina was found to be 343 microg g(-1) for lithium. Under the optimal operation condition, the detection limit (DL) of on-line preconcentration corresponding to three times the standard deviation of the blank (S/N = 3) was found to be 1.3 ng mL(-1) and the RSD of this method is 3.32% (n = 5). The on-line calibration graph was linear over the range 20 - 200 ng mL(-1). A good preconcentration factor 820 was achieved by experiment under the on-line mode. The developed method was applied to the analysis of trace lithium in nuclear grade uranium compounds.     

A surfactant–heme–sulfonyl imidazole system as a nano-artificial enzyme

The heme–imidazole–sodium dodecyl sulfate (SDS) ternary complex has been designed as a peroxidase-like nano-artificial enzyme, in which the imidazole moiety functions like the histidine ligand in the native horseradish peroxidase (HRP) and increases the reactivity and catalytic efficiency of the designed artificial enzyme by promoting the heterolytic cleavage of hydrogen peroxide. In the present study, three different ligands were used as the imidazole-based ligands in the heme–ligand–SDS ternary system: (1) 1-methylsulfonyl-1H-imidazole, (2) 1-(benzensulfonyl)-1H-imidazole, and (3) 1-tosyl-1H-imidazole (TsIm). The three different ligands gave variable reactivity in the system studied, and the enzymatic activation parameters, using spectrophotometric measurements, showed that the TsIm ligand had a higher catalytic efficiency at 26.38 % of the native HRP efficiency. To investigate the increase in catalytic activity, its mechanism was explored based on the original mechanism of HRP and the structure of its first catalytic intermediate (compound I). Based on the mechanism of HRP and the structure of compound I, a suggested mechanism for Tslm is as follows: the TsIm cation radical makes up part of the compound I structure, which is stabilized in the enzymatic process by charge distribution that is induced via phenyl and methyl groups. Suicide inactivation of heme–TsIm–SDS and heme–imidazole–SDS models was also compared to each other. Suicide inactivation was less exhibited in the presence of TsIm than imidazole in this system unless high concentrations of hydrogen peroxide were used.     

Multi-residue determination of 41 insecticides in garlic by gas chromatography and ion trap mass spectrometry using the selective ion storage technique

A method is described for determining 41 insecticide residues in garlic (Allium sativum L.), including organophosphorus, organochlorine, carbamate, and synthetic pyrethroid insecticides. These insecticides were extracted from samples with acetone and dichloromethane, and co-extractives removed using a charcoal/Celite/alumina column. Analysis was performed by gas chromatography with ion trap mass spectrometry in selective ion storage (SIS) mode. Retention times and specific ions (m/z values) were used to confirm insecticides. Recoveries for most insecticides (blank samples spiked at 0.05, 0.2 and 1 microg mL(-1) levels) ranged from 70% to 110%, the coefficient of variation (CV) of the method was <20% for every case, and the limit of detection (LOD), defined in terms of 3 times baseline noise, varied between 0.01 and 0.16 mg kg(-1), depending on the compound.     

表面活性剂对Al2O3吸附MoO4^2—的影响

土壤自溶液中吸附MoO_4~(2-)会影响植物生长。前人对这一吸附过程已作过一些研究。本文报导阴离子表面活性剂十二烷基硫酸钠(SDS),阳离子表面活性剂氯化十六烷基吡啶(CPC)和非离子表面活性剂吐温-20(TW-20)对Al_2O_3吸附MoO_4~(2-)的影响。 实验所用吸附剂为层析用中性Al_2O_3(上海五四农场化学试剂厂),SDS(化学纯,广东石岐化工厂),CPC(化学纯。上海试剂一厂),TW—20(试剂级),其余试剂均为分析纯,含钼液用Na_2MoO_4配制。