A capacitively coupled microwave plasma atomic emission spectrometer for the determination of trace metals in microsamples

A capacitively coupled microwave plasma operating at 450 to 850 W is used for atomic emission spectroscopy. The laboratory-constructed system contains a tungsten cup electrode capable of holding a volume of up to 30 μl. Microwaves are used to dry the sample, while at higher powers the plasma is ignited for sample vaporization and excitation. The entire analysis can be carried out in less than 5 min. A mixture of helium and hydrogen is used as the plasma gas. A spherical or cylindrical shaped plasma can be formed depending upon the gas flow rate and the microwave power selected. The effects of experimental parameters, such as gas flow rate, atomization power, electrode position and plasma shape are examined. Detection limits for Cd, Mg and Zn are in the low picogram range for a 10 μl sample; the relative standard deviation is less than 10%.     

Electrothermal vaporization system using furnace-fusion technique for the determination of lead in botanical samples by inductively coupled plasma atomic emission spectrometry

A new approach to sample digestion, subsequent vaporization and introduction into an inductively coupled plasma atomic emission spectrometer was developed for the direct determination of lead. To each small sample cuvette made of tungsten, a mixture of a ground solid sample and powdered diammonium hydrogenphosphate was precisely weighed. The cuvette was positioned onto the tungsten boat furnace (TBF) incorporating a vaporizer. Tetramethylammonium hydroxide solution was added. Then the cuvette was heated and maintained at a wet-digestion temperature to decompose the solid sample. After digestion, the temperature was elevated to generate the analyte vapor for introduction into a plasma. Since the solid samples were wet-digested in the sample cuvettes before vaporization, they could be analyzed by using a calibration curve prepared from aqueous standard solutions. This method was applied to the determination of lead in several biological materials with satisfactory results.     

Electrothermal vaporization system using furnace-fusion technique for the determination of lead in botanical samples by inductively coupled plasma atomic emission spectrometry

A new approach to sample digestion, subsequent vaporization and introduction into an inductively coupled plasma atomic emission spectrometer was developed for the direct determination of lead. To each small sample cuvette made of tungsten, a mixture of a ground solid sample and powdered diammonium hydrogenphosphate was precisely weighed. The cuvette was positioned onto the tungsten boat furnace (TBF) incorporating a vaporizer. Tetramethylammonium hydroxide solution was added. Then the cuvette was heated and maintained at a wet-digestion temperature to decompose the solid sample. After digestion, the temperature was elevated to generate the analyte vapor for introduction into a plasma. Since the solid samples were wet-digested in the sample cuvettes before vaporization, they could be analyzed by using a calibration curve prepared from aqueous standard solutions. This method was applied to the determination of lead in several biological materials with satisfactory results.     

Study on the direct analysis of solid powder biological samples using fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry with PTFE slurry modifier

A method has been described for the direct determination of Ti, Cu, Mn, Cr and Cd in solid biological samples without any chemical pretreatment by fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) with slurry sampling. A polytetrafluorethylene (PTFE) emulsion was used as a fluorinating reagent to promote the vaporization of the analytes from the graphite furnace. The interface between furnace device and ICP torch and the main factors affecting the analytical signal were investigated systematically. The detection limits for the determination of Ti, Cu, Mn, Cr and Cd are 6.3, 4.7, 10, 13 and 278 ng/mL, respectively; the relative standard deviations are in the range of 1.5 (Mn) ∼4.0% (Cd) after optimization of the operating conditions. The recommended approach has been applied to directly determine the trace elements of interest in the Chinese traditional medicine Loulu and in the solid biological standard reference material (peach leaves, GBW 08501) with satisfactory results. Received: 28 December 1998 / Revised: 9 February 1999 / Accepted: 12 February 1999     

Study on the direct analysis of solid powder biological samples using fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry with PTFE slurry modifier

A method has been described for the direct determination of Ti, Cu, Mn, Cr and Cd in solid biological samples without any chemical pretreatment by fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) with slurry sampling. A polytetrafluorethylene (PTFE) emulsion was used as a fluorinating reagent to promote the vaporization of the analytes from the graphite furnace. The interface between furnace device and ICP torch and the main factors affecting the analytical signal were investigated systematically. The detection limits for the determination of Ti, Cu, Mn, Cr and Cd are 6.3, 4.7, 10, 13 and 278 ng/mL, respectively; the relative standard deviations are in the range of 1.5 (Mn) ∼4.0% (Cd) after optimization of the operating conditions. The recommended approach has been applied to directly determine the trace elements of interest in the Chinese traditional medicine Loulu and in the solid biological standard reference material (peach leaves, GBW 08501) with satisfactory results. Received: 28 December 1998 / Revised: 9 February 1999 / Accepted: 12 February 1999     

Direct atomic absorption determination of cadmium and lead in strongly interfering matrices by double vaporization with a two-step electrothermal atomizer

Thermal pretreatment of a sample using double vaporization in a two-step atomizer with a purged vaporizer makes possible the direct analysis of samples with strongly interfering matrices including solids. A porous-graphite capsule or a filter inserted into the vaporizer is used for solid sample analysis. The technique was used for the direct determination of Cd and Pb in human urine, potatoes, wheat, bovine liver, milk powder, grass–cereal mixtures, caprolactam, bituminous-shale and polyvinyl chloride plastic without chemical modification or any other sample pretreatment.     

Determination of cadmium,mercury and lead in coal fly ash by slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry

Ultrasonic slurry sampling electrothermal vaporization isotope dilution inductively coupled plasma mass spectrometry (USS-ETV-ID-ICP-MS) has been applied to the determination of Cd, Hg and Pb in coal fly ash samples. Thioacetamide (TAC) was used as the modifier. Since the sensitivities of the elements studied in coal fly ash slurry and aqueous solution were quite different, isotope dilution method was used for the determination of Cd, Hg and Pb in these coal fly ash samples. The isotope ratios of each element were calculated from the peak areas of each injection peak. This method has been applied to the determination of Cd, Hg and Pb in NIST SRM 1633a coal fly ash reference material and a coal fly ash sample collected from Kaohsiung area. Analysis results of reference sample NIST SRM 1633a coal fly ash agreed satisfactorily with the certified values. The other sample determined by isotope dilution and method of standard additions was agreed satisfactorily. Precision was better than 6% for most of the determinations and accuracy was better than 4% with the USS-ETV-ID-ICP-MS method. Detection limits estimated from standard addition curves were in the range of 24–58, 6–28 and 108–110 ng g⁻¹ for Cd, Hg and Pb, respectively.     

A new approach of direct sample-digestion before vaporization for determination of a metal in rocks by inductively coupled plasma atomic emission spectrometry.

A new approach to sample digestion, subsequent vaporization and introduction to an inductively coupled plasma (ICP) atomic emission spectrometer was developed for the direct determination of magnesium. To each small sample cuvette made of tungsten, a ground rock sample was precisely weighed. The cuvette was situated on a tungsten boat furnace. Ammonium fluoride solution was added to the cuvette as a chemical modifier. After the on-furnace digestion has been completed, the analyte, magnesium, in the cuvette was vaporized and introduced into the ICP atomic emission spectrometer. Since the powdered samples were wet-digested in the sample cuvettes prior to vaporization, they could be analyzed by using a calibration curve prepared from aqueous standard solutions. This method was applied to the determination of magnesium in several standard reference materials with satisfactory results.     

Electrothermal vaporization in inductively coupled plasma atomic emission spectrometry for direct multielement analysis of food samples with slurry sampling

Slurry sampling followed by electrothermal vaporization (ETV) was used as sample introduction technique in inductively coupled plasma atomic emission spectrometry (ICP-AES) for the direct determination of trace elements in food samples. A polytetrafluoroethylene (PTFE) emulsion was used as a fluorinating reagent to promote vaporization and the transportation of analytes. The main factors affecting the analytical signals were investigated in detail. Under optimum operating conditions, the detection limits (DL) for this method varied from 1.8 (Cu) to 215 ng/mL (Zn), while the relative standard deviations (RSD) were in the range 2.6% (Cu)-7.2% (Zn). The proposed method was successfully applied to the direct determination of trace amounts of V, Cu, Cr, Fe, Zn, and La in rice without any chemical pretreatment. The precision was evaluated by analyzing a standard reference material (tea leaves, GBW 07605) and comparing the results from this method with results obtained by pneumatic nebulization (PN) ICP-AES after the wet-chemical decomposition of the same sample.From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 3, 2005, pp. 286–290.Original English Text Copyright © 2005 by Chen.This article was submitted by the author in English.     

Multielement Analysis of Whole Blood Using a Capacitively Coupled Microwave Plasma Atomic Emission Spectrometer

A capacitively coupled microwave plasma atomic emission spectrometer (CMP-AES) has been evaluated as a means for the direct analysis of several of the primary and trace elements in whole blood. A tungsten filament spiral electrode was used with the CMP, and whole blood samples were deposited on the electrode and subsequently dried, ashed, and atomized. The emission was measured with a spectrometer and a charge-coupled-device detector. A sample size of only 2 μl was required and the time for each sample run was under 4 min. This method has a wide dynamic range, allowing the determination of both the primary elements in blood and elements present in trace quantities. Potassium, sodium, lithium, magnesium, manganese, and zinc were studied. Good linearity was observed and the concentration levels obtained for these elements were consistent with literature values. The primary advantages of this method are that no sample pretreatment or dilution is required, the instrument cost is low, and the method is capable of simultaneous multielement analysis on small, discrete samples.     

电热蒸发进样微波诱导等离子体原子吸收光谱法测定银和镉的研究

研究了以常压低功率氩微波诱导等离子体（ＭＩＰ）为原子化器的原子吸收光谱法（ＡＡＳ）测定银和镉。采用电热蒸发（ＥＴＶ）,浓Ｈ２ＳＯ４吸收去溶的进样方法。考察了微波前向功率,载气流量,去溶电压,去溶时间,蒸发电压,酸度对银,镉测定的影响。方法已用于试样分析。     

Zirconia-coated graphite adsorption bar micro-extraction combined with ETV-ICP-MS for the determination of trace amounts of Cd, Hg and Pb in environmental and biological samples

In this work, a new and simple micro-extraction method termed graphite adsorption bar micro-extraction was developed, for the first time, for electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) determination of trace Cd, Hg and Pb. In this method, the graphite bar was first coated with zirconia and then inserted into the sample solution for extraction. The graphite bar enriched with the analytes was inserted directly into a graphite tube, and subsequently analyzed by ETV-ICP-MS according to an established temperature program. The experimental parameters, which had influence on the extraction and vaporization, were systematically investigated and the optimal experimental conditions were established. Under the optimized conditions, the detection limits of the method were 0.05, 0.42 and 0.06 pg/ml for Cd, Hg and Pb and the relative standard deviations (RSDs) for 11 replicates at the 0.1 ng/ml level were 7.4, 8.2 and 7.7%, respectively. The proposed method was successfully applied to the determination of trace Cd, Hg and Pb in environmental and biological samples. The results of the experiments indicate that the method has a high enrichment factor and sample utilization efficiency. Furthermore, the method is fast and environment-friendly.     

The development of a method for the determination of trace elements in fuel alcohol by electrothermal vaporization–inductively coupled plasma mass spectrometry using external calibration

A method for the determination of Ag, As, Cd, Cu, Co, Fe, Mn, Ni, Pb, Sn and Tl in fuel alcohol by electrothermal vaporization inductively coupled plasma mass spectrometry is proposed. The determinations were carried out by external calibration against ethanolic solutions, without a chemical modifier, employing the following pyrolysis and vaporization temperatures: 400 °C and 2300 °C for the more volatile analytes and 1000 °C and 2500 °C for the less volatile analytes. The determination of As, Cd, Pb, Sn and Tl was additionally carried out using Pd as modifier at 800 °C pyrolysis and 2400 °C vaporization temperatures. The temperatures were optimized through pyrolysis and vaporization curves. Seven common fuel ethanol, one fuel ethanol with additive and one anhydrous fuel ethanol sample have been analyzed. The measured concentrations were at the μg L⁻¹ level or lower. Since there is no certified reference material for fuel ethanol, the accuracy of the method was checked by the recovery test, with recoveries from 75% to 124%. The limits of detection (LODs), in μg L⁻¹, and the relative standard deviations for 5 replicates were, for the elements in the conditions without modifier: Ag: 0.015 and 9.1%, Co: 0.002 and 10%, Cu: 0.22 and 6.6%, Fe: 0.72 and 4.3%, Mn: 0.025 and 12%, Ni: 0.026 and 9.3%, and for the elements with Pd: As: 0.02 and 2.9%, Cd: 0.07 and 25%, Pb: 0.02 and 3.1%, Sn: 0.010 and 6.0%, Tl: 0.0008 and 2.5%. Electrothermal vaporization avoids the loading of the plasma with organics, allowing the analysis of fuel ethanol by ICP-MS with good accuracy and reasonable precision.     

Determination of Cd,Pb and Sr by Microwave Plasma Torch Atomic Emision Spectrometry Using an Electrothermal Vaporization Sample Introduction System

ＩｎｔｒｏｄｕｃｔｉｏｎＥｌｅｔｒｏｔｈｅｒｍａｌｖａｐｏｒｉｚａｔｉｏｎ（ＥＴＶ）ａｓａｍｅａｎｓｏｆｓａｍｐｌｅｉｎｔｒｏｄｕｃｔｉｏｎｉｎｍｉｃｒｏｗａｖｅｉｎ－ｄｕｃｅｄｐｌａｓｍａ（ＭＩＰ）ｓｏｕｒｃｅｓｐｅｃｔｒｏｍｅｔｒｙｈａｓｂｅｅｎ...     

Direct analysis of tantalum powders by electrothermal vaporization inductively coupled plasma atomic emission spectrometry

A direct inductively coupled plasma atomic emission method for the determination of Ag, Al, As, Ca, Cd, Co, Cu, Fe, Ga, K, Li, Mg, Na and Pb in high-purity tantalum powders has been developed. The electrothermal vaporization technique using a modified longitudinally-heated Grün-ETAAS furnace with sample introduction on a platform and an automated sampling workstation provided the possibility of in situ analyte-matrix separation, freedom of blank, and applicability to routine analysis. Hard- and software were modified to allow signal recording and data processing independent of the spectrometer software. The extent of spectral interferences by Ta-emission at the analyte wavelengths used was determined and the analyte signals of each sample run were automatically corrected. Limits of detection ranging from 5 ng/g (Ag, Cu) to 250 ng/g (K, Pb) were obtained using optimized furnace and spectrometer conditions. The method was applied to the analysis of two tantalum samples and the results for Cu, Fe, K, Mg and Na were compared with those obtained by liquid and solid-samping ETAAS, showing satisfactory agreement.     

Electrothermal vaporization inductively coupled plasma atomic emission spectrometry for the analysis of solid samples: contribution to instrumentation and methodology

Summary A commercially available graphite furnace was modified in order to use it as an electrothermal vaporization device for solid sample analysis with an inductively coupled plasma atomic emission spectrometer. An evaluation of two different ETV systems has been made. This paper mainly describes the different aspects which must be taken into account when coupling an ETV system to an ICP. Cu was chosen as an element easy to determine and Cd and Pb as elements with more difficulties. From the optimization it was found that the transport efficiency for Cd in solution and solid is different, whereas for Cu and Pb the efficiencies are in good agreement for both sample types. Calibration with solids and liquids was attempted for Cu. The paper gives preliminary results on the determination of Cu in solid reference materials. In some cases (e.g. Pb) a background correction based on a linear interpolation seemed not satisfactory. Detection limits and limits of determination for Cu, Cd and Pb in different solid samples are given.Presented at the 5th International Colloquium on Solid Sampling with Atomic Spectroscopy, May 18–20, 1992; Geel, Belgium. Papers edited by R. F. M. Herber, Amsterdam     

Potential of Solid Sampling Electrothermal Vaporization for solving spectral interference in Inductively Coupled Plasma Optical Emission Spectrometry

Spectral interference is one of the main causes of erroneous results in Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). This paper describes some cases of spectral interferences with conventional nebulization ICP-OES and the potential of solving them utilizing electrothermal vaporization for volatility-based separation. The cases studied were, the well-known spectral overlap between the As and Cd lines at 228.8 nm that are only 10 pm apart, and the interference of Fe on the main emission lines of As, Cd and Pb. The spectral interferences were studied by monitoring the typical signals of solutions that contain the analytes and the potential interferent, by studying the spectra and calculating Background Equivalent Concentration (BEC)-values. A three step temperature program was developed to be used for direct analysis of solid soil samples by Electrothermal Vaporization (ETV)-ICP-OES: step 1 (760 °C, 40 s), step 2 (1620 °C, 20 s) and a cleaning step (2250 °C, 10 s) where Cd vaporizes in step 1, As, Pb and part of Fe in step 2 and the major part of Fe in the cleaning step. Because As and Cd were time-separated using this program, their prominent lines at 228.8 nm, could be used for determination of each element by ETV-ICP-OES, in spite of the serious wavelength overlap. Selective vaporization was also shown to reduce or eliminate the Fe background emission on As, Cd and Pb lines. To confirm the applicability of the method, a solid soil certified reference materials was analyzed directly without any sample treatment. Good or reasonable accuracy was obtained for the three elements.     

Direct inductively coupled plasma-atomic emission spectrometry analysis of trace elements in muscle tissues of hairtail using electrothermal vaporization with slurry sampling

A procedure for direct determination of trace elements in muscle tissue of hairtail was developed using inductively coupled plasma-atomic emission spectrometry and electrothermal vaporization with slurry sampling. Due to use of polytetrafluoroethylene as the chemical modifier, the vaporization behaviors of analytes from the slurry and the aqueous standard solutions were very similar. In this case, the aqueous standards could be used for the calibration of slurry samples. The main factors influencing this method were studied systematically. The detection limits for Cr, Ni, Zn, Cd, and Pb were 3.1, 10.5, 176, 6.9, and 83 ng/mL, respectively, and the relative standard deviations were less than 10%. The proposed method was applied to the determination of trace Cr, Ni, Zn, Cd, and Pb in hairtail samples with satisfactory accuracy and precision. A certified reference material of mussel (GBW 08571) was analyzed, and good agreement was obtained between the results from the proposed method and certificate values.     

Cadmium Determination in Sedimented Dust by Atomic Emission Spectrometry With a New Radiofrequency Capacitively Coupled Plasma Source

ABSTRACT

A new radiofrequency capacitively coupled plasma source (r.f.CCP) was used for Cd determination in dust samples by atomic emission spectrometry. The plasma torch consists of a molybdenum tube electrode and one or two ring electrodes situated outside the quartz tube. Plasma was operated at 27.12 MHz, at low power (275 W) and low gas consumption (0.4 1 min^? argon flow). The choice of the optimum operating conditions for Cd determination in dust samples dissolved in acids and pneumatically nebulized is presented. The results obtained in such samples were compared with those obtained by flame atomic absorption spectrometry (FAAS). The matrix effect of NaCl and CaCl₂ on Cd emission was also studied depending of the plasma coupling system. The true limit of detection for Cd in dust sample by r.f.CCP-AES is 3 μg g^?1. Concentration of Cd higher than 10 μg g^?1 can be determined by the proposed method with a relative standard deviation within the range 5 - 10%. The recovery is 100 ± 10%.     

Slurry Sampling Electrothermal Vaporization Combined with ICP-AES for Direct Analysis of Environmental Samples

In this article, a polytetrafluoroethylene (PTFE) slurry was used as a chemical modifier for direct determination of trace elements in environmental samples by electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) with slurry sampling. The vaporization behaviors of the analytes in slurry and solution were comparatively studied in the presence of PTFE. The main influence factors for this method were examined. Under the optimum operating conditions, the precision of this method was better than 7% with the detection limits varying from 1.7 ng mL^?1 (Cu) to 203 ng mL^?1 (Zn). The proposed method has been applied to the direct determination of the trace elements in camphor tree leaves and standard reference material (the combined sample of branch and leaf of shrub, GBW 07603) with satisfactory results.