Mass spectrometric and gas and high-performance liquid chromatographic behaviour of an impurity in 2,5-hexanedione

The analysis of 2,5-hexanedione, a metabolic compound of several industrial solvents, is normally carried out using gas chromatographic (GC) or GC-mass spectrometric (MS) techniques. This work, with the aim of verifying the possibility of determining the diketone by means of a high-performance liquid chromatographic (HPLC) method with UV detection, illustrates the importance of the choice of a 2,5-hexanedione standard for the determination of the diketone response factor. In some commercial diketone samples the presence of an impurity, which may interfere with the analysis of the target analyte, was ascertained. This impurity showed GC and HPLC behaviour similar to that of 2,5-hexanedione, but gave a very different UV response. This impurity was identified as 3-methylcyclopent-2-enone by means of MS, GC-MS, HPLC-photodiode-array detection, IR and UV spectrometry. The structure was confirmed by comparing the chromatographic, mass and ultraviolet data of the unknown compound with those of a synthesized reference sample. The well known difficulty in determining 2,5-hexanedione by HPLC with UV detection was reconfirmed owing to its low molar absorptivity.     

Evaluation of chromatographic and spectroscopic methods for the analysis of petroleum-derived compounds in the environment

Summary Analytical protocols have been adapted for the study of hydrocarbons at the trace level in the environment. Various samples, including sediments and biota, were collected from the Kuwaiti environment, treated according to the protocol and analyzed by chromatographic and spectroscopic methods. The methods used were synchronous scanning fluorescence spectroscopy (SSFS); high-performance liquid chromatography (HPLC) on C18 reversed-phase and NH2 normal-phase columns with UV and fluorescence detectors; gas chromatography on fused-silica capillary columns (GC) with flame ionization detector (FID), mass spectrometer (MS) and flame photometric detector (FPD); and high-resolution molecular spectrofluorimetry in Shpol'skii matrix at 10 K (HRSS). The different methods were found to give complementary information. SSFS was useful for fast evaluation and preliminary assessment of oil pollution during extended programs; it permitted sample selection for deeper analyses but, when applied to biota, needed special care in the clean-up procedure. GC/FID, was used to analyze saturated and ethylenic compounds and was useful for obtaining information on the origin of hydrocarbons but inconvenient for analyzing the aromatic fraction. GC/FPD was difficult to use with sediment samples and yielded little information on biota samples, although it did permit confirmation of high oil contamination in some examples. HPLC on a normal-phase column with UV and fluorescence detectors was useful for the fractionation of samples and for the separation of different families of aromatic compounds according to aromatic carbon number. GC/MS was used to quantify polycyclic aromatic hydrocarbons (PAHs) of less than four cycles but was not sensitive enough for PAHs of higher molecular weight. HRSS, however, was useful for the quantification of heavy PAHs and was also faster, could be automated, and gave accurate results. However, in an oil-pollution study, it must be backed up by the other techniques. In fact, no single analytical technique was found to be sufficient, and only judicious combinations of the tested techniques yielded adequate information on the origin of hydrocarbons in the environment.     

Analytical separation and detection methods for flavonoids

Flavonoids receive considerable attention in the literature, specifically because of their biological and physiological importance. This review focuses on separation and detection methods for flavonoids and their application to plants, food, drinks and biological fluids. The topics that will be discussed are sample treatment, column liquid chromatography (LC), but also methods such as gas chromatography (GC), capillary electrophoresis (CE) and thin-layer chromatography (TLC), various detection methods and structural characterization. Because of the increasing interest in structure elucidation of flavonoids, special attention will be devoted to the use of tandem-mass spectrometric (MS/MS) techniques for the characterization of several important sub-classes, and to the potential of combined diode-array UV (DAD UV), tandem-MS and nuclear magnetic resonance (NMR) detection for unambiguous identification. Emphasis will be on recent developments and trends.     

Liquid chromatography-tandem mass spectrometry for the identification of impurities in d-allethrin samples

A previous GC/MS study highlighting the impurity profile of the synthetic pesticide d-allethrin is extended here to validate and confirm the impurities identity through the development of soft ionisation HPLC-MS methods. To accomplish this, we developed a reverse phase LC-MS analysis in gradient elution with two distinct soft ionisation techniques, the atmospheric pressure ionisation with electrospray source (API-ESI) and the chemical ionisation (APCI). A single quadrupole and an ion trap, which allowed the simultaneous determination of the molecular masses and structural information of the impurities by acquisition of collisionally induced (CID) product ions spectrum and in-source fragmentation, were employed as analysers. Single quadrupole and ion trap analysers resulted perfectly matching in the d-allethrin impurity fragmentation patterns. All the main impurities over 0.1% identified by GC/MS were confirmed. Results indicate that the proposed HPLC/MS method was found appropriate to confirm the presence of impurities such as chrysolactone, chloro allethrin derivatives, allethrolone and chrysanthemic acid, excluding their formation under GC/MS strong ionisation condition.     

Sensitive and rapid determination of elemental nanosulfur/sulfur by liquid chromatography

In order to identify the most suitable method for the estimation of nanosulfur for studying its residue dynamics, the present work was taken up. HPLC and GC methods were explored for its analysis. A comparative study of the existing analytical methods for the quality control of nanosulfur was undertaken. UV spectrophotometry and HPLC methods were superior with lower LOD when compared to GC–MS, which was not satisfactory due to breakage of catenated S₂₀ into S₆ and S₈. The method has been validated by analyzing various nanosulfur formulations of known concentrations. The recovery of the UV and HPLC methods ranged from 80.71 to 109.51% and 82.31 to 109.84%, respectively. The LOD of UV, GC–MS, and HPLC is 4, 20, and 1 ppm, respectively. The retention time of sulfur was 13.77 (HPLC), 2.89 (ultra high performance liquid chromatography), and 12.715 + 21.524 min (GC–MS). The method was successfully utilized for estimating sulfur in natural samples such as water from a sulfur hot spring and wastewater. The method has been validated by following the method recommended by the American Society for Testing and Materials. The HPLC method emerged as the best analytical method for the estimation of elemental sulfur.     

Study on the photostability of guaiazulene by high-performance liquid chromatography/mass spectrometry and gas chromatography/mass spectrometry

The photostability of guaiazulene (1,4-dimethyl-7-isopropylazulene; GA), a natural azulenic compound used in cosmetic and health-care products, as well as in pharmaceutical preparations, was investigated in solution (methanol, ethanol, acetonitrile), by different techniques: gas chromatography/mass spectrometry (GC/MS) and high-performance liquid chromatography combined with atmospheric pressure chemical ionization mass spectrometry and UV detection (LC/APCI-MS and HPLC/UV). A solar simulator (xenon-arc lamp) was used as UV-A radiation source. The study involved: monitoring compound decomposition, identifying products of photodegradation (PPs), assessing the role of oxygen and evaluating the kinetics of the process. Minor PPs are volatile compounds and were characterized by GC/MS, while oligomeric polyoxygenated compounds, tentatively characterized on the basis of MS and MS/MS spectra, were found to be the main photoproducts. The photodegradation was found to be enhanced by the presence of oxygen; nevertheless, determination of the singlet oxygen quantum yield for GA gave a lower value than that for the reference standard Rose Bengal. The obtained results and the developed stability-indicating methods (GC/MS and LC/MS) are of interest for stability studies and/or quality control purposes of GA as raw material or cosmetic products.     

Metabolite analysis in Curcuma domestica using various GC‐MS and LC‐MS separation and detection techniques

The metabolic profile of polar (methanol) and non‐polar (hexane) extracts of Curcuma domestica, a widely used medicinal plant, was established using various different analytical techniques, including GC‐FID, GC‐MS, HR‐GC‐MS and analytical HPLC‐ESI‐MS/MS by means of LTQ‐Orbitrap technology. The major non‐volatile curcuminoids curcumin, demethoxycurcumin and bisdemethoxycurcumin were identified when their chromatographic and precursor ion masses were compared with those of authentic standard compounds. In this paper we describe for the first time a GC/MS‐based method for metabolic profiling of the hydrophilic extract. We also identified 61 polar metabolites as TMS derivatives. Copyright © 2009 John Wiley & Sons, Ltd.     

Analysis of steroids XXXIX. Estimation of the impurity profile of 5α-androst-2-ene-17-one

Summary The impurity profile of 5-androst-2-ene-17-one was investigated by using two different capillary gas chromatographic (GC) and a reverse phase high performance liquid chromatographic systems (HPLC). The impurities were identified by retention matching with authentic standards, diode-array UV spectroscopy, on-line gas chromatography-mass spectrometry (GC-MS), off-line HPLC-MS and NMR spectroscopy. The following impurities were identified and quantitated: ring A saturated, isomeric (1-ene, 3-ene, 4-ene, 5-ene) analogues, 3 and 3-hydroxy as well as 3-phenyl derivatives.For Part XXXVIII, see Reference [1]. This paper is Part III in a series of papers Estimation of Impurity Profiles of Drugs and Related Materials. For Part II, see Reference [2].     

The application of sub-2-microm particle liquid chromatography-operated high mobile linear velocities coupled to orthogonal accelerated time-of-flight mass spectrometry for the analysis of ranitidine and its impurities

Impurity profiling of pharmaceutical drug substances or dosage formulations require methods involving high sensitivity and resolution from LC and MS alike as well as an acceptable analysis time. While throughput can be increased, it is usually at the expense of chromatographic resolution. The application of sub-2-microm stationary phases and high mobile linear velocities has been combined with orthogonal acceleration (oa)-TOF MS for the impurity structural characterization analysis of small-molecule pharmaceutics. A pharmaceutical drug substance was forcefully degraded and used to test the proof of concept of developing an impurity profile method by ultra performance liquid chromatography (UPLC). Optimum conditions were identified by use of method development simulation software as well as traditional approaches of method scouting with columns and a varied range of pH. Further analysis illustrated the effectiveness of applying oa-TOF MS techniques to assist in achieving exact mass coupled with MS/MS to define the structural characterization of the related substances relative to the pharmaceutical active ingredient and identification of any unknown impurity substances. The barriers with trade-offs between resolution and speed are overcome by the application of UPLC, whereas the increased sensitivity provides for superior exact mass oa-TOF MS.     

Stability and Photoisomerization of Stilbenes Isolated from the Bark of Norway Spruce Roots

Stilbenes or stilbenoids, major polyphenolic compounds of the bark of Norway spruce (Picea abies L. Karst), have potential future applications as drugs, preservatives and other functional ingredients due to their antioxidative, antibacterial and antifungal properties. Stilbenes are photosensitive and UV and fluorescent light induce trans to cis isomerisation via intramolecular cyclization. So far, the characterizations of possible new compounds derived from trans-stilbenes under UV light exposure have been mainly tentative based only on UV or MS spectra without utilizing more detailed structural spectroscopy techniques such as NMR. The objective of this work was to study the stability of biologically interesting and readily available stilbenes such as astringin and isorhapontin and their aglucones piceatannol and isorhapontigenin, which have not been studied previously. The effects of fluorescent and UV light and storage on the stability of trans stilbenes were assessed and the identification and characterisation of new compounds formed during our experiments were carried out by chromatographic (HPLC, GC) and spectroscopic techniques (UV, MS, NMR). The stilbenes undergo a trans to cis isomerisation under extended UV irradiation by intramolecular cyclisation (by the formation of a new C-C bond and the loss of two hydrogens) to phenanthrene structures. The characterised compounds are novel and not described previously.     

Resolution of the Co-eluting Impurity 3,4-Dihydro-3,3-dimethylisoquinoline in Phentermine Base Using HPLC-UV Photodiode Array Detection Followed by Identification via GC-(EI+)-MS

Abstract

In the course of process development for phentermine base, samples were observed to fail the UV specification. Analysis using the HPLC purity profile method did not yield unusual results. However, re-analysis using UV-photodiode array detection indicated the presence of an impurity that almost exactly co-elutes with the phentermine peak. Comparison of these samples with previously manufactured lots known to pass the UV test, along with area comparison of the impurity, permitted its determination by GC. Previous efforts had tentatively identified this peak 2,3,3 trimethylindolenine. Further evaluation using GC(EI+)MS confirmed the identity of the peak as 3,4-dihydro-3,3-dimethylisoquinoline, formed via a Bischler-Napieralski type reaction (cyclodehydration of acyl derivatives). The impurity was eliminated from the process by minimizing those factors that contribute to its formation. Assay of the     

Requirements for bioanalytical procedures in postmortem toxicology

The application of analytical techniques in postmortem toxicology is often more difficult than in other forms of forensic toxicology owing to the variable and often degraded nature of the specimens and the diverse range of specimens available for analysis. Consequently, analysts must ensure that all methods are fully validated for the particular postmortem specimen(s) used. Collection of specimens must be standardized to minimize site-to-site variability and should if available include a peripheral blood sample and at least one other specimen. Urine and vitreous humor are good specimens to complement blood. In some circumstances solid tissues such as liver are recommended as well as gastric contents. Substance-screening techniques are the most important element since they will determine the range of substances that were targeted in the investigation and provide initial indication of the possible role of substances in the death. While immunoassay techniques are still commonly used for the most common drugs-of-abuse, chromatographic screening methods are required for general unknown testing. These are still predominately gas chromatography (GC) based using nitrogen/phosphorous detection and/or mass spectrometry (MS) detection, although some laboratories are now using time-of-flight MS or liquid chromatography (LC)–MS(MS) to cover a sometimes more limited range of substances. It is recommended that laboratories include a second chromatographic method to provide coverage of acidic and other substances not readily covered by a GC-based screen when extracts do not include all physiochemical types. This may include a gradient high-performance liquid chromatography (HPLC) photodiode array method, or better LC-MS(MS). Substance-specific techniques (e.g., benzodiazepines, opiates) providing a second form of identification (confirmation) are now divided between GC-MS(MS) and LC-MS(MS) procedures. LC-MS(MS) has taken over from many methods for the more polar compounds previously used in HPLC or in GC methods requiring derivatization. Analysts using LC-MS will need to obtain clean extracts to avoid poor and variable sensitivity caused by background suppression of the signal. Isolation techniques in postmortem toxicology tend to favor liquid extraction; however solid-phase extraction and solid-phase microextraction methods are available for many analytes.     

Analyses of two azo dyes by high-performance liquid chromatography

Two structurally similar azo dyes, Direct Blue No. 6 and Direct Blue No. 15, are analyzed by separate reversed-phase high-performance liquid chromatographic (HPLC) systems utilizing a dual-wavelength UV/visible detector at 254 and 546 nm. Each dye contains more than 35 impurity peaks. Different lots of each dye are compared by means of their respective chromatographic profiles. The system used to obtain a chromatographic profile for each dye is adapted to make comparisons of the major component in different lots by an internal standard method. These methods are reproducible, giving relative standard deviations ranging from approximately 1 to 5%. These HPLC systems are adaptable for the analysis of other structurally similar dyes.     

On-Line HPLC with Biochemical Detection for Screening Bioactive Compounds in Complex Matrixes

On-line high-performance liquid chromatography (HPLC) coupled with biochemical detection (BCD) has been developed to screen compounds showing antioxidant action, enzyme inhibition and receptor affinity in complex matrixes. This review summarizes HPLC methods combining different post-column detection methods, such as diode-array detection (DAD), mass spectrometry (MS), chemiluminescence (CL) and nuclear magnetic resonance, for antioxidant screening. The methods based on a single relatively stable reagent such as DPPH^• and ABTS^•+ were the most popular. Oxygen free radical scavengers mainly depended on post-column CL detection. The on-line hyphenated HPLC–BCD systems based on post-column UV/DAD fluorescence and MS detection were also widely applied to screen enzyme- and receptor-active compounds. These strategies provide a convenient tool for quick identification and quantification of active compounds in complex matrixes.

     

High-performance ion-pair chromatography method for simultaneous analysis of alliin,deoxyalliin, allicin and dipeptide precursors in garlic products using multiple mass spectrometry and UV detection

The quality of garlic and garlic products is usually related to their alliin content and allicin release potential. Until now no analytical method was able to quantify simultaneously allicin, its direct precursor alliin (S-allyl-L-cysteine sulfoxide), SAC (S-allyl-L-cysteine) as well as various dipeptides that apparently serve as storage compounds in garlic. It is well known that all these intermediates are involved in the allicin biosynthetic pathway. A simple and rapid HPLC method suitable for routine analysis was developed using eluents containing an ion-pairing reagent. Particularly, heptanesulfonate as ion-pairing reagent guarantees a sufficient separation between alliin and the more retained dipeptides at very low pH. Allicin was eluted after 18 min on a 150 x 3 mm column. Synthetic reference compounds were characterized by the same chromatographic method using a diode-array UV detector and an ion trap mass spectrometer (electrospray ionization) in the multiple MS mode. In routine analysis of garlic bulbs, powders and other products, the diode-array detector is sufficient for a relevant quantification. Our method has been used in studies to improve the quality of garlic and its derived products.     

Collection of analytical data for benzodiazepines and benzophenones

On April 1st, 1986, amendments were made to Schedule 2 to the Misuse of Drugs Act 1971 such that 33 benzodiazepines became controlled as Class C drugs in the U.K. An analytical database has been prepared to aid the detection and identification of controlled benzodiazepines. Chromatographic properties have been measured including gas chromatography (GC) retention index values, high-performance liquid chromatography (HPLC) capacity factors and thin-layer chromatography (TLC) RF x 100 values. UV spectroscopic and mass spectrometric (MS) data have also been recorded. Analytical data (GC, TLC and MS) are also presented for benzophenones which were produced by acid hydrolysis of the parent benzodiazepines.     

Quantitative liquid chromatography/tandem mass spectrometry determination of chloramphenicol residues in food using sub-2 microm particulate high-performance liquid chromatography columns for sensitivity and speed

The use of chloramphenicol (CAP)--a highly effective broad-spectrum antibiotic used in animal husbandry--is banned in many countries. Therefore, a very low minimum required performance limit (MRPL) of 0.3 microg/kg CAP in meat for human consumption has been defined. Analytical methods capable of quantifying and confirming such low residue levels require sophisticated instrumentation. Preferably sensitive liquid chromatography/tandem mass spectrometry (LC/MS/MS) or gas chromatography/mass spectrometry (GC/MS) methods have been used. This paper suggests the use of sub-2 microm particulate high-performance liquid chromatography (HPLC) columns to gain additional sensitivity and improve resolution as well as speed. Depending on the operating conditions, higher chromatographic resolution and speed can be obtained at the price of a significantly increased operating pressure, requiring dedicated LC equipment. A 3-4-fold overall improvement of the signal-to-noise ratio for CAP was obtained compared to more classical 5 microm particulate HPLC columns. The proposed analytical methodology includes an enzymatic digestion, which liberates glucuronide-bound CAP from kidney tissue. The extracts obtained after an Extrelut clean-up are sufficiently pure to permit routine injection of biological samples into the sub-2 microm particulate HPLC column, without observing rapid deterioration of peak shape or column clogging problems. The time for one chromatographic run was 4.2 min. The described method was validated for two particularly difficult matrices (kidney and honey). Decision limits (CC alpha) were 0.007 microg/kg (honey) und 0.011 microg/kg (kidney), which are significantly below the current MRPL.     

我国环境中有机污染物分析方法及痕量富集技术的进展

对有机污染物分析在近年进展作了评述。其主要内容涉及试样的预处理技术（如顶空法,吹扫-捕集法,固相萃取,半透膜等技术）,各化合物的适用及有效的分析方法或仪器（如GC,HPLC及GC／MS等）以及各种技术及方法的联用技术等（引述文献37篇）。     

Differentiation and dating of red ink entries of seals on documents by HPLC and GC/MS

A novel approach for differentiation and dating of red ink entries of seals on documents was developed based on ion‐pairing HPLC (IP‐HPLC) and GC/MS. Sixty‐nine red ink pastes of seals were collected and the chromatographic conditions for separation of the dye components by IP‐HPLC and the volatile additives by GC/MS in the ink entries were optimized. According to the dye components and additives, the ink entries were classified by HPLC with a multi‐wavelength UV detector. The volatile components of the inks were identified by GC/MS and the classification of the ink entries was also investigated based on these volatile additives. The results showed that most of the ink entries of the seals can be differentiated by combining HPLC with a multi‐wavelength detector and GC/MS methods. The degradation of the standard dye mixtures and the compositional changes of the ink entries of seals were investigated in light or natural aging conditions. The results indicated that the dye components decomposed in light or natural storage conditions, while the rates of the degradation depended on the structures of the dye components, the aging conditions, even the additives of the ink pastes. The results also showed that there existed good relationships between the compositional changes of the ink entries and the aging time, which can provide scientific evidences and valuable clues for dating of the ink entries.