Isolation and determination of toxic congeners of polychlorinated biphenyls in environmental samples

A Method has been developed for the separation and enrichemen of there non-ortho, eight mono-ortho, and di-ortho substituted polychlorinated biphenyls (PCBs) from Aroclor formulations and environmental samples. The fractionation is accomplished using high performance liquid chromatography (HPLC) with a 2-(1-pyrenyl)ethyldimethylsilysily silca column. GC-MSD with an optimized temperature program was used for quantitation, Hexane, pentane, cyclohexane, iso-octane, and 2-propanol were tested as a mobile phase for the isolation of the thirteen target PCBs in a Aroclor 1242, 1254, and 1260 (1:1:1) misture, Pentane at room temperature with a slow rate of 0.7 ml/min is the condition of choice. The average recovery of thirteen target PCBs spiked in the Aroclor mixture is 99.5% with an average relative standard deviation of 4.5%. The average method detection limit is 8pg/μl. Targer PCBs in the reference solis, incinarator ash, and sediment samples were measured.     

Ratios of PCB 138, PCB 163, and PCB 164 in aroclor mixtures

The gas chromatographic separation of PCB 138, PCB 163, and PCB 164 in Aroclor mixtures can be achieved by application of a CP-Select for PCBs stationary phase. In technical PCB mixtures with a degree of chlorination exceeding 40% (Aroclor 1242, 1254, 1260, and 1262) these three hexa-chlorobiphenyls were present. The highest concentrations of the PCBs under investigation were found in Aroclor 1260. The ratio PCB 163: PCB 138 increased with an increasing degree of chlorination of technical PCB mixtures.     

Group separation of organohalogenated compounds by means of comprehensive two-dimensional gas chromatography

Separations of 12 compound classes, polychlorinated biphenyls (PCBs), diphenyl ethers (PCDEs), naphthalenes (PCNs), dibenzothiophenes (PCDTs), dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), terphenyls (PCTs) and alkanes (PCAs), toxaphene, organohalogenated pesticides (OCPs), and polybrominated biphenyls (PBBs) and diphenyl ethers (PBDEs) by comprehensive two-dimensional gas chromatography were evaluated. Five column combinations, DB-1 x 007-210, DB-1 x HT-8, DB-1 x LC-50, DB-1 x 007-65HT and DB-1 x VF-23ms were used to study, primarily, group-type separations, but attention was devoted also to within-class separation, especially for those classes which were not addressed in much detail before, the PCNs, OCPs, PBBs and PCTs. The DB-1 x 007-210 column set did not offer any extra separation compared to one-dimensional GC. For the DB-1 x HT-8 column combination, the useful principle of congener separation on the basis of number of halogen substituents in a molecule was confirmed (PCBs, toxaphene) and extended (PCTs, PBDEs). No practically useful group-type separation was observed for this column combination. The DB-1 x LC-50 set provides group separation based on planarity: planar compounds such as PCDDs, PCDFs, PCDTs and PCNs are much more retained than, and therefore separated from, non-planar analytes. Within the classes of PCBs, PBBs and PCTs highly useful separation of planar from non-planar compounds was also observed. The DB-1 x 007-65HT column set effectively separates PCAs and PBDEs from all other compound classes, and provides a good separation of brominated and chlorinated analogue classes from each other. This column set was the most efficient one for within-class separation of OCPs and PCNs. Finally, DB-1 x VF-23ms yields excellent within-class separations, especially of non-aromatic compounds, viz. OCPs, toxaphene and PCAs. No group separation was observed here. The applicability of the approach was demonstrated for a sediment extract and a dust extract. In the sediment extract, PCDDs, PCDFs, PCAs and PCNs were identified and their efficient separation was achieved. In the dust sample, separation of PCAs and PBDEs was achieved and several new PBDE congeners were identified.     

Determination of 26 polychlorinated biphenyls congeners in soil samples using microwave-assisted extraction with open vessel and gas chromatography

A procedure focused on microwave-assisted extraction in open vessel (MAE-OV) and gas chromatography with electron capture detection (GC-ECD) was used for the determination of 26 congeners of polychlorinated biphenyls (PCBs) in soil samples. The limit of detection (LOD) and limit of quantification (LOQ) were evaluated for commercial PCBs mixture Aroclor1260. LOD and LOQ were calculated for each PCB congener, in the ranges (0.03–0.27?ng?g^?1) and (0.11–0.70?ng?g^?1), respectively. After optimization, 26 PCBs congeners were successfully extracted from soil samples with recovery amounts ranging between 84.7% and 117.3% for all PCBs congeners. The evaluated method of MAE-OV showed good separation and extraction of all PCBs congeners from soil samples. Extraction parameters such as solvent choice, power and extraction time were investigated. This study indicated that MAE-OV could be an interesting alternative method to extract PCBs from soils, since it is economical, easy, fast and requires low amounts of solvents.     

A calculation mode for the correct GC/ECNI-MS-SIM determination of polychlorinated terphenyls in the presence of high excesses of polychlorinated biphenyls

Polychlorinated terphenyls (PCTs) are a class of persistent organic pollutants difficult to analyze by gas chromatography with mass spectrometry operated in the selected ion monitoring mode (GC/MS-SIM) in environmental samples due to the retention time and mass range overlap with polychlorinated biphenyls (PCBs). To overcome these drawbacks, we developed and evaluated a mathematical calculation algorithm which allows to detail the interference of PCT congeners in GC/electron capture negative ion (ECNI)-MS-SIM chromatograms by PCBs. The calculation takes advantage of the abundance and ratio of two suitable isotope peaks of the molecular ion of PCTs. With the help of this method, we detected at least 63 tetra- to nonachlorinated terphenyls in the blubber of a harbour porpoise (Phocoena phocoena) from the North Sea. The interference of these peaks by PCBs ranged from >100 to 0?%. The novel calculation method used in combination with GC/ECNI-MS-SIM is suitable to analyze PCTs in environmental and food samples. However, it can also be applied to GC/EI-MS measurements.     

Liquid chromatographic isolation of coplanar PCB congeners on an activated carbon stationary phase

A rapid and uncomplicated method for the fractionation of PCBs leading to an isolation of the highly toxic non-ortho substituted PCBs is described. The liquid chromatographic separation was achieved on a stationary phase consisting of activated carbon and Celite 545. Using eluents with different polarity, isolation of the non-ortho substituted PCBs in a single fraction was achieved. The fractions were analysed by GC/MS. The method was tested by the determination of non-ortho substituted PCBs in technical mixtures (Aroclor 1254 and Aroclor 1242). The results were compared with those obtained by using an HPLC fractionation on a porous graphitic carbon column. Finally, the micro-column fractionation was used for the determination of non-ortho substituted PCBs in native soil samples.     

Catalytic dechlorination of Aroclor 1242 by Ni/Fe bimetallic nanoparticles

Ni/Fe bimetallic nanoparticles were synthesized for treatment of Aroclor 1242, in order to evaluate their applicability for in situ remediation of groundwater and soil contaminated by polychlorinated biphenyls (PCBs). Our experimental results indicate that the total PCB concentration changed during the reduction of 3,5-dichlorobiphenyl (PCB 14), and biphenyl was produced as the final product. Initially, the concentration of 3-chlorobiphenyl (PCB 2) was increased in the prophase reaction and then slowly decreased, suggesting that Aroclor 1242 was first adsorbed by Ni/Fe nanoparticles, and then, the higher chlorinated congeners were converted gradually to the lower chlorinated congeners, and finally to biphenyl. The dechlorination efficiency of Aroclor 1242 reached approximately 80% at 25°C in just 5h, then 95.6% and 95.8% in 10h and 24h, respectively. The study revealed that high Ni/Fe nanoparticle dosage and high Ni content in Ni/Fe nanoparticles favor the catalytic dechlorination reaction. Moreover, a comparison of different types of catalysts on the dechlorination of Aroclor 1242 indicated that Ni/Mg and Mg powders showed a greater reactivity than Ni/Fe and Fe nanoparticles, respectively.     

Liquid chromatographic isolation of coplanar PCB congeners on an activated carbon stationary phase

A rapid and uncomplicated method for the fractionation of PCBs leading to an isolation of the highly toxic non-ortho substituted PCBs is described. The liquid chromatographic separation was achieved on a stationary phase consisting of activated carbon and Celite 545. Using eluents with different polarity, isolation of the non-ortho substituted PCBs in a single fraction was achieved. The fractions were analysed by GC/MS. The method was tested by the determination of non-ortho substituted PCBs in technical mixtures (Aroclor 1254 and Aroclor 1242). The results were compared with those obtained by using an HPLC fractionation on a porous graphitic carbon column. Finally, the micro-column fractionation was used for the determination of non-ortho substituted PCBs in native soil samples. Received: 5 March 1997 / Revised: 4 June 1997 / Accepted: 6 June 1997     

Polychlorinated biphenyls,dibenzo-p-dioxins and dibenzofurans in soil samples from airport areas of Croatia

Levels and patterns of polychlorinated biphenyls (PCBs) were studied in surface soil samples collected in the coastal part of Croatia within and surrounding four different airports and in the vicinity of two partially devastated electrical transformer stations. The compounds accumulated from air-dried soil samples by multiple ultrasonic extraction with an n-hexane?:?acetone 1?:?1 mixture were analysed by capillary gas chromatography with electron capture and ion-trap detection. PCBs were quantified against a standard Aroclor 1242/Aroclor 1260 mixture and a standard mixture of 17 individual PCB congeners (IUPAC No.: 28, 52, 60, 74, 101, 105, 114, 118, 123, 138, 153, 156, 157, 167, 170, 180, and 189). The mass fractions of total PCBs in 18 soil samples collected within the airport premises ranged from 3 to 41?327?µg/kg dry weight (dw) (median: 533?µg/kg?dw), and those in 21 samples collected at a distance ranging from several metres to 5?km away from the airport fence, from <1 to 39?µg/kg?dw (median: 5?µg/kg?dw). The highest PCB levels were determined in soils along the airport aprons where the aircrafts were serviced and refuelled. The PCB pattern was very similar to technical Aroclor 1260 in all airport soils. The PCB pattern in 22 soils collected in the vicinity of electrical transformer stations was dominated by congeners contained in Aroclor 1242. These soils contained 7 to >400?µg/kg?dw of total PCBs. One highly PCB-contaminated airport soil sample was analysed for polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). With an international toxic equivalent (I-TEQ) of 9.7?ng/kg?dw, the airport soil contamination was within values typical for urban and rural areas, and the congener patterns gave no clear indication for PCBs as the only source of PCDDs/PCDFs.     

Enhanced comprehensive two-dimensional gas chromatographic resolution of polychlorinated biphenyls on a non-polar polysiloxane and an ionic liquid column series

A total of 196 out of 209 polychlorobiphenyl (PCB) congeners were resolved using GC×GC-TOFMS with a non-polar/ionic liquid column series consisting of poly(50%-n-octyl-50%-methyl)siloxane and (1,12-di(tripropylphosphonium)dodecane bis(trifluoromethansulfonyl)amide) in the first and second dimension, respectively. It has been found that 13 PCB congeners overlap in five doublets (CB12+CB13, CB62+CB75, CB70+CB76, CB97+CB125 and CB153+CB168) and one triplet (CB90+CB101+CB113). All toxic, "dioxin like" congeners were separated with no interferences from any PCB congener. The 109 PCBs present in Aroclor 1242 and the 82 PCBs present in Aroclor 1260 were resolved GC×GC-TOFMS analysis on this column set.     

Diol sep-pak cartridges for enrichment of polychlorobiphenyls and chlorinated pesticides from water samples; determination by GC-ECD

Summary Gas chromatography of polychlorinated biphenyls and chlorinated pesticides in water samples has been performed after adsorption from a 20–200-mL sample on to a cartridge containing 100 mg diol-bonded porous silica. The PCBs are desorbed with 500 μL ethyl acetate, which is concentrated and analysed by gas chromatography with electron-capture detection (GC-ECD). The average recovery of 0.1 ng mL⁻¹ PCB congeners from distilled water and from Aniene river water is≥95% (standard deviation≤2.8). Average recoveries of 25 ng mL⁻¹ Aroclor 1254 from distilled water and from Aniene river water were, respectively, 94.4% and 92.5% (standard deviation 5.8). In the separation of PCB congeners from the chlorinated pesticides only the aldrin (40%) was eluted with the PCBs from the diol Sep-Pak cartridge by aqueous methanol. The method described is simple and reproducible.     

Determination of PCBs in tetrachlorinated quinone using gas chromatography with electron capture detection

A simple, sensitive method for determining polychlorinated biphenyl (PCB) congeners in industrial product 2,3,5,6-tetrachloro-1,4-benzoquinone with GC/ECD detection has been developed. The method based on liquid-liquid extraction from tetrachlorinated quinone dissolved in N,N-dimethylformamide was found to be efficient for the determination of the levels of the investigated pollutants. A series of extraction and purification steps were designed for the sample pretreatment. The congener specific averages of recoveries were 82-96% for Aroclor 1242 and 1254 at a total spiking level of ca. 0.4 mug g(-1) sample. The reproducibilities of replicate determinations of different congeners were typically 5-19% except one with the average 13% R.S.D. (n=3). This method was applied to evaluate the background levels of PCBs in tetrachloro-1,4-benzoquinone, of which the corresponding PCB levels varied from 0.014 to 1.5 mug g(-1).     

Use of a polar ionic liquid as second column for the comprehensive two-dimensional GC separation of PCBs

The orthogonality of three columns coupled in two series was studied for the congener specific comprehensive two-dimensional GC separation of polychlorinated biphenyls (PCBs). A non-polar capillary column coated with poly(5%-phenyl–95%-methyl)siloxane was used as the first (¹D) column in both series. A polar capillary column coated with 70% cyanopropyl-polysilphenylene-siloxane or a capillary column coated with the ionic liquid 1,12-di(tripropylphosphonium)dodecane bis(trifluoromethane-sulfonyl)imide were used as the second (²D) columns. Nine multi-congener standard PCB solutions containing subsets of all native 209 PCBs, a mixture of 209 PCBs as well as Aroclor 1242 and 1260 formulations were used to study the orthogonality of both column series. Retention times of the corresponding PCB congeners on ¹D and ²D columns were used to construct retention time dependences (apex plots) for assessing orthogonality of both columns coupled in series. For a visual assessment of the peak density of PCBs congeners on a retention plane, 2D images were compared. The degree of orthogonality of both column series was, along the visual assessment of distribution of PCBs on the retention plane, evaluated also by Pearson's correlation coefficient, which was found by correlation of retention times t_R,i,2D and t_R,i,1D of corresponding PCB congeners on both column series. It was demonstrated that the apolar + ionic liquid column series is almost orthogonal both for the 2D separation of PCBs present in Aroclor 1242 and 1260 formulations as well as for the separation of all of 209 PCBs. All toxic, dioxin-like PCBs, with the exception of PCB 118 that overlaps with PCB 106, were resolved by the apolar/ionic liquid series while on the apolar/polar column series three toxic PCBs overlapped (105 + 127, 81 + 148 and 118 + 106).     

Sequential solid-phase extraction with cyanopropyl bonded-phase cartridges for trace enrichment of PCBs and chlorinated pesticides from water samples

Summary Gas chromatography of polychlorinated biphenyls and chlorinated pesticides in water samples has been performed after adsorption from a 50–250 mL sample on to a cartridge containing 100 mg cyanopropyl-bonded porous silica. The PCBs are desorbed with 500 μL ethyl acetate, which is concentrated and analysed by gas chromatography with electron-capture detection (GC-ECD). The average recovery of 1 ppb PCB congeners at from distilled water and from Marta river water is ≥95% (standard deviation ≤2.5). The average recovery of 20 ppb Aroclor 1260 from Marta river water was ≥91% (standard deviation ≤3.5). In the separation of the PCBs from the chlorinated pesticides only aldrin, heptachlor and 4,4′-DDD are adsorbed with the PCBs by the CN Sep-Pak cartridge. The method proposed is rapid, simple and reproducible.     

Extractants for Organochlorine Insecticides and Polychlorinated Biphenyls from Water

A reversed liquid-liquid partition system prepared from Chromosorb W, n-undecane and Carbowax 4000 monostearate was shown to be suitable for extracting organochlorine insecticides and polychlorinated biphenyls (PCBs) from water (with the exception of Aroclor 1260). The performances of the partition system, Amberlite XAD-4, porous poly- urethane foam and the solvent extraction technique when applied to the analysis of four environmental water samples were comparable (except for Aroclor 1260).     

Simultaneous determination of aliphatic hydrocarbons,PCBs and PCTs in pork liver by gas chromatography

Summary A multicomponent extraction/concentration procedure has been developed for the enrichment of PCBs, PCTs and aliphatic hydrocarbons (pristane, C₁₈, C₁₉, C₂₀, C₂₂, C₂₄, C₂₈, C₃₂ and C₃₆) in pork liver. These components of the enriched extract were then simultaneously determined by gas chromatography. Mean recoveries ranged from 81.5% for pristane to 93% for PCBs;CV% (0.9–6.7) indicated the method to be both precise and reproducible.     

Microbore columns vs. open tubular columns for supercritical fluid chromatography in environmental analysis: Separation of polychlorinated biphenyls and terphenyls

The supercritical fluid chromatographic behavior of polychlorinated biphenyls (PCBs) and polychlorinated terphenyls (PCTs) is described. The method uses a microbore C-18 column and an open tubular capillary column coated with SE-52 and carbon dioxide as the supercritical fluid. Factors affecting the separation and retention of these compounds are discussed.     

Analysis of organochlorines in harbor seal (Phoca vitulina) tissue samples from Alaska using gas chromatography/ion trap mass spectrometry by an isotopic dilution technique

A gas chromatography/ion trap mass spectrometry (GC/ITMS) method was developed for the determination of organochlorine pesticides (OCPs), polychlorinated biphenyls (PCBs) and polychlorinated naphthalenes (PCNs) in harbor seal (Phoca vitulina) tissues. Tissue samples were homogenized, lyophilized and fortified with (13)C-PCBs 28, 123, 169 and 170, and then extracted with an accelerated solvent extractor with a mixture of hexane and methylene chloride (1:1, v/v). After lipid removal using a 40% H(2)SO(4)-modified silica gel column, all organochlorines were collected in one fraction and further fractionated with an activated carbon/silica gel (1:20) column into a first fraction containing OCPs, non-coplanar PCBs and (13)C-PCBs 28, 123 and 170, and a second containing PCNs, coplanar PCBs and (13)C-PCB 169. Prior to GC/MS/MS analysis, (13)C-PCB 169 was added into the first fraction as an injection standard and (13)C-PCB 170 into the second fraction to calibrate the recoveries of the fortified internal standards. This method can effectively eliminate matrix interferences, and has high selectivity and sensitivity. Recoveries averaged 45-86% for OCPs with relative standard deviations (RSDs) of 2-14%, 52-137% for PCBs with RSDs of 3-29% and 36-152% for PCNs with RSDs of 7-29% from lard and chicken heart samples, which were used as alternative matrices to harbor seal samples in recovery studies. The limits of detection for OCPs, PCBs and PCNs were 0.7-1.9, 1.5-8.9 and 0.5-10 pg/g dry weight, respectively. This method can be used to analyze OCPs, PCBs and PCNs in harbor seal blubber, liver and kidney samples.     

Development of a screening method for the determination of PCBs in water using QuEChERS extraction and gas chromatography-triple quadrupole mass spectrometry

A new method has been developed and validated for the simultaneous analysis of 11 polychlorinated biphenyls (PCBs), in water samples at trace levels by gas chromatography coupled to triple quadrupole mass spectrometry (GC-QqQ-MS/MS). Water samples were extracted by the QuEChERS (Quick Easy Cheap Effective Rugged and Safe) method. The QqQ analyzer acquired data in multiple reactions monitoring (MRM), permitting both quantification and confirmation in a single injection with a running time reduced up to 11.0 min. The effect of matrix interferences in extracts on analyte quantification and the identification of PCBs in water samples was deeply studied. The results showed that PCBs were prone to strong matrix interactions in water samples, and the quantification and identification of PCBs were highly affected by a matrix enhancement effect. To evaluate the performance of the method, validation experiments were carried out on water samples at three spiking levels (1.6, 8.0, 40.0 μg L(-1)). Recovery was in the range of 95 - 109% at 1.6 μg L(-1), 90 - 95% at 8.0 μg L(-1) and 97 - 102% at 40.0 μg L(-1), respectively. Precision values expressed as relative standard deviation (RSD) were lower than 15%. Linearity in the range of 0.5 - 50.0 μg L(-1) provided determination coefficients (R(2)) higher than 0.999 for all compounds. The limits of detection (LODs) for PCBs were ≤0.1 μg L(-1) and the limits of quantification (LOQs) ranged from 0.04 to 0.3 μg L(-1). The applicability of the proposed method to detect and quantify PCBs has been demonstrated in analyse of 15 real samples.     

Characterization of three Aroclor mixtures using a new cyanobiphenyl stationary phase

The retention characteristics of all 209 polychlorinated biphenyl (PCB) congeners were determined on a new p,p-cyanobiphenyl stationary phase using gas chromatography with electron capture detection (GC-ECD). Response factors were determined relative to decachlorobiphenyl, PCB 209. Several congeners that coelute on the phases routinely used for PCB analysis are separated on this phase, including the hexachlorobiphenyls 138, 163, and 164. The p,p-cyanobiphenyl stationary phase exhibits altered retention for planar congeners, such that the toxic coplanar PCBs 77, 126, and 169 are eluted free from interference. Of the 209 congeners, 61 were separated using the p,p-cyanobiphenyl phase in conjunction with GC-ECD. When analyzed by gas chromatography with mass selective detection (GC-MSD), the number of congeners determined increased to 133. Therefore GC-MSD was used with the p,p-cyanobiphenyl phase to characterize three PCB mixtures: Aroclor 1242, Aroclor 1254, and Aroclor 1260.