Optimization of a chemical modifier in the determination of selenium by graphite furnace atomic absorption spectrometry and its application to wheat and wheat flour analysis.

A method for the determination of total selenium in wheat and wheat flour using graphite furnace atomic absorption spectrometry (GFAAS) with palladium/ascorbic acid as a chemical modifier was studied. The effects of nickel nitrate, palladium/ascorbic acid, and palladium/magnesium nitrate as chemical modifiers on the sensitivity in the determination of selenite, selenate and selenomethionine by GFAAS were compared. The palladium/ascorbic acid modifier was used for the determination of total selenium in wheat and wheat flour, because the oxidation states of the selenium ion are not important in the determination. The detection limit was estimated to be 1 microg L(-1) (calculated as 3sigma of the blank); the calibration curve was linear for the concentration range 5 - 50 microg L(-1) and the recovery range was 96.66 - 101.80%. The optimal ashing and atomizing temperatures were 1300 degrees C and 2250 degrees C, respectively. The proposed method was successfully applied to the determination of total selenium in wheat and wheat flour.     

Direct determination of selenium in a wild fruit juice by electrothermal atomic absorption spectrometry

A matrix modifier composed of platinum and nickel is proposed for the determination of selenium in a wild fruit juice made from Lantingguo (Vuccinium uliginosam). Five matrix modifiers (copper/nickel, palladium/magnesium, platinum/magnesium, platinum/nickel and platinum/copper) for suppressing the interference effects of seven co-existing elements (potassium, phosphorus, calcium, magnesium, manganese, zinc and iron) in a wild juice were studied and a matrix modifier composed fro;m 10 mug of platinum and 200 mug of nickel was found to give the best performance. Selenium in three juices was determined by electrothermal atomic absorption spectrometry employing the proposed matrix modifier without matrix preseparation. The relative standard deviation was 14% for 0.20 mg l(-1) of selenium. The recoveries were 95-110%. A characteristic mass was 28 pg.     

Atomic absorption spectrometric screening and gas chromatographic-mass spectrometric determination of organotin compounds in marine mussels: an application in samples from the Venetian Lagoon

A new analytical approach for the determination of organotin compounds (OTC) in mussel samples has been developed and evaluated. A preliminary step, performed by graphite furnace atomic absorption spectrometry (GFAAS) for the total tin determination may be followed by gas chromatographic-mass spectrometric (GC/ MS) speciation only for the characterization of those samples exhibiting total tin concentration higher than 30 ng/g wet weight (GFAAS limit of detection). The GFAAS method was optimized using Pd nitrate under reducing conditions as matrix modifier to minimize NaCl interferences. Organotins were derivatized with a Grignard reagent for GC/MS analysis (TBT limit of detection = 80 ng/g). An application of this strategy was performed on mussel samples collected from the Venetian Lagoon.     

Determination of selenium in ores, concentrates and related materials by graphite-furnace atomic-absorption spectrometry after separation by extraction of the 4-nitro-o-phenylenediamine complex

A method for determining approximately 0.01 mug/g or more of selenium in ores, concentrates, rocks, soils, sediments and related materials is described. After sample decomposition selenium is reduced to selenium(IV) by heating in 4M hydrochloric acid and separated from the matrix elements by toluene extraction of its 5-nitropiazselenol complex from approximately 4.2M hydrochloric acid. After the extract has been washed with 2% nitric acid to remove residual iron, copper and chloride, the selenium in the extract is oxidized to selenium(VI) with 20% bromine solution in cyclohexane and stripped into water. This solution is evaporated to dryness in the presence of nickel, and selenium is ultimately determined in a 2% v/v nitric acid medium by graphite-furnace atomic-absorption spectrometry at 196.0 nm with the nickel functioning as matrix modifier. Common ions, including large amounts of iron, copper and lead, do not interfere. More than 1 mg of vanadium(V) and 0.25 mg each of platinum(IV), palladium(II), and gold(III) causes high results for selenium, and more than 1 mg of tungsten(VI) and 2 mg of molybdenum(VI) causes low results. Interference from chromium(VI) is eliminated by reducing it to chromium(III) with hydroxylamine hydrochloride before the formation of the selenium complex.     

Direct determination of boron in a cobalt-based alloy by graphite furnace-atomic absorption spectrometry

A matrix modifier composed of nickel and zirconium, and a graphite tube treated with zirconium solution were proposed for the determination of boron in cobalt-based alloys by graphite furnace-atomic absorption spectrometry. The effects of this matrix modifier and the treated graphite tube were studied, and the combination of 60 mug of nickel and 20 mug of zirconium as matrix modifier, and a graphite tube soaked with 10 g 1(-1) of zirconium solution were found to give the highest analytical sensitivity. The interference effects of major components (cobalt) and eight minor components (chromium, nickel, tungsten, iron, tantalum, molybdenum, titanium, aluminium and manganese) were studied. Boron in four cobalt-based alloys was determined by graphite furnace-atomic absorption spectrometry employing the proposed matrix modifier and the treated graphite tube, without the preseparation of matrix. The relative standard deviation was 3.3% for 0.048% of boron. A characteristic mass was 500 pg.     

Direct determination of parts-per-billion levels of germanium in botanical samples and coal fly ash by graphite furnace atomic absorption spectrometry

 Parts-per-billion levels of germanium can be determined directly by graphite furnace atomic absorption spectrometry (GFAAS) using palladium plus strontium as a mixed modifier resulting in pyrolysis temperatures up to 1400 °C without loss of germanium. At this temperature the matrix effect including the most troublesome sulfate interference can be eliminated. Palladium plus strontium nitrate is advantageous compared to palladium alone or palladium plus magnesium nitrate; an amount of 15 μg of sulfate does not show any interference on the determination of 1 ng of germanium. The method was successfully applied to the determination of ng/g levels of germanium in botanical samples and coal fly ash after thermal decomposition of the samples in a mixture of acids using a pressure bomb. The results were consistent with the reference values given for botanical samples and coal fly ash with a recovery range of 96.4∼103.4% Received: 16 September 1996/Revised: 10 December 1996/Accepted: 14 January 1997     

Anion-exchange high-performance liquid chromatographic determination of ascorbic acid and hexavalent chromium in rat lung preparations after treatment with sodium chromate in vitro and in vivo

Simultaneous analysis of ascorbic acid and chromium (VI) in soluble fractions and bronchoalveolar lavage fluids of rat lungs treated with sodium chromate in vitro and in vivo was performed by anion-exchange high-performance liquid chromatography coupled to a photodiode-array detector. Absorbances at 265 and 370 nm were used for the determination of ascorbic acid and chromium (VI), respectively. The calibration graphs of standard solutions were linear in the test ranges of ascorbic acid an chromium (VI) (below 10 and 8 ppm, respectively). The detection limits of ascorbic acid and chromium (VI) were 1 and 0.5 ng, respectively. The recovery of ascorbic acid from lung tissues homogenized at pH 7.4 was 99%, and that of chromium (VI) was 96%, when tissues were homogenized under alkaline conditions (pH 11.4). Using this method, ascorbic acid levels in the soluble fractions and lavage fluids of normal rat lungs were determined. In the lung of a rat intratracheally injected with a saline solution of sodium chromate, ascorbic acid decreased to 80% of the normal level, and ca. 90% of the chromium (VI) was reduced within 4 min after injection, indicating that the ascorbic acid-related reduction of chromium (VI) is very rapid. The present method will be useful for studies of the reduction of chromium (VI) by ascorbic acid in biological systems.     

Direct determination of germanium in botanical samples by graphite furnace atomic absorption spectrometry with palladium-zirconium as chemical modifier

A method has been described for the direct determination of trace levels of germanium by graphite furnace atomic absorption spectrometry (GFAAS) using chemical matrix modification technique. The stabilization and the pyrolysis temperatures for germanium were investigated with various chemical modifiers including palladium, palladium–magnesium, palladium–strontium and palladium–zirconium. The highest pyrolysis temperature and highest integrated absorbance were obtained using palladium–zirconium modifier, and the severe matrix interference from sulfate can be eliminated. The characteristic mass and absolute detection limit (3σ) of germanium were found to be 16 and 12 pg, respectively. The proposed method was applied to the determination of trace levels of germanium in botanical samples with a recovery range of 92–106%. The hydride generation atomic fluorescence spectrometric (HGAFS) method was employed to analyze the samples and the results agree well with those obtained by GFAAS. The contents of germanium in standard reference materials were determined and the results were in good agreement with the reference values.     

Coprecipitation with lanthanum phosphate as a technique for separation and preconcentration of iron(III) and lead

The usefulness of coprecipitation with lanthanum phosphate for separation and preconcentration of some heavy metals has been investigated. Although lanthanum phosphate coprecipitates iron(III) and lead quantitatively at pH 2.3, iron(II) can barely be collected at this pH. This coprecipitation technique was applicable to the separation and preconcentration of iron(III) before inductively coupled plasma atomic-emission spectrometric (ICP-AES) determination; the recoveries of iron(III) and iron(II) from spiked water samples were 103-105% and 0.2-0.7%, respectively. The coprecipitation was also useful for separation of 20 microg lead from 100 mL of an aqueous solution that also contained 1-100 mg iron. Coprecipitation of iron was substantially suppressed by addition of ascorbic acid, which enabled recovery of 97-103% of lead added to the solution, bringing the recovery to within 1.6-5.0% of the relative standard deviations. Lanthanum phosphate can also coprecipitate cadmium and indium quantitatively, although chromium(III), cobalt, and nickel and large amounts of sodium, potassium, magnesium, and calcium are barely coprecipitated at pH approximately/= 3.     

Determination of cadmium, chromium, copper and lead in sediments and soil samples by electrothermal atomic absorption spectrometry using zirconium containing chemical modifiers.

A method for direct determination of cadmium, chromium, copper and lead in sediments and soil samples by electrothermal atomic absorption spectrometry using Zr, Ir, etylenediamine acetic acid (EDTA), Zr + EDTA, Ir + EDTA, Zr + Ir and Zr + Ir + EDTA as chemical modifiers in 0.5% (v/v) Triton X-100 plus 0.2% (v/v) nitric acid mixture used as diluent was developed. The effects of mass and mass ratio of modifiers on analytes in sample solutions were studied. The optimum masses and mass ratios of modifiers: 20 microg of Zr, 4 microg of Ir, 100 microg of EDTA and 20 microg of Zr + 4 microg of Ir + 100 microg of EDTA, were used to enhance the analyte signals. Pyrolysis and atomization temperatures, atomization and background absorption profiles, characteristic masses, and detection limits of analytes in samples were compared in the presence or absence of a modifier. The detection limits and characteristic masses of analytes in a 0.5% (m/v) dissolved sample (dilution factor of 200 ml g(-1)) obtained with Zr + Ir + EDTA are 8.0 ng g(-1) and 1.2 pg for Cd, 61 ng g(-1) and 4.3 pg for Cr, 32 ng g(-1) and 23 pg for Cu, and 3.4 ng g(-1) and 19 pg for Pb, respectively. The Zr + Ir + EDTA modifier mixture was found to be preferable for the determination of analytes in sediment and soil-certified and standard reference materials. Depending on the sample type, the percent recoveries of analytes were increased from 81 to 103% by using the proposed modifier mixture; the results obtained are in good agreement with the certified values.     

1,5-bis(dicarboxymethylaminomethyl)-2,6- dihydroxynaphthalene as a selective spectrofluorimetric reagent for calcium

1,5-Bis(dicarboxymethylaminomethyl)-2,6-dihydroxynaphthalene (BDDN) forms fluorescent complexes with aluminium, barium, beryllium, calcium, magnesium and strontium. All the complexes have 2:1 metal :ligand ratios. Barium, calcium, magnesium and strontium exhibit maximal fluorescence at pH 11.7, with excitation and emission maxima at 385 and 445 nm respectively. Aluminium and beryllium show maximal fluorescence at pH 5.8 and 5.2 respectively, the excitation and emission maxima being at 370 and 405 nm. The formation of the calcium complex provides a highly sensitive and selective determination of calcium in the range 10/2-500 ng. The fluorescence measurement of calcium should be made within 5 min of mixing the solutions because of the instability of the reagent at the given pH. Potassium cyanide may be used as a masking agent and ter- or quadrivalent cations should be removed by preliminary extraction with 8-hydroxyquinoline in chloroform at pH 6.0. In such conditions, of 33 cations studied, only magnesium (>20 ng), strontium (>70 ng) and barium (>150 ng) caused interference in the determination of 300 ng of calcium. Among 16 anions examined, only EDTA interfered seriously.     

平台石墨炉原子吸收法直接测定全血中痕量锗

研究了基体改进及其用量，锗的灰化和原子化温度以及６种共存离子的干扰，采用锶和硝酸铵混合液作基体改进剂，锗的灵敏度高，提高了方法的选择性，样品不需消化与分离，可采用平台石墨炉法直接测定血样中的痕量锗。     

Separation and preconcentration of Se(IV)/Se(VI) species by selective adsorption onto nanometer-sized titanium dioxide and determination by graphite furnace atomic absorption spectrometry

A simple and sensitive method for the selective determination of Se(IV) and Se(VI) in natural water and sludge samples through an adsorptive process on a nanometer-sized TiO(2) (anatase) was developed. The conditions for quantitative and reproducible preconcentration, elution, and subsequent GFAAS determination were established. The proposed method gave a concentration factor of 50 for a 100 mL sample volume, characterized by high precision, high reproducibility, and direct determination of Se(IV)/Se(VI). The detection limits (3 sigma, n=11) were 4.7ng L(-1) for Se(IV) and 6.3ng L(-1) for Se(VI); the precision (relative standard deviation) was 0.7% for Se(IV) and 0.9% for Se(VI) at the 0.5microg L(-1) level.     

石墨炉原子吸收光谱法测定痕量镉的基体改进效应研究及其应用

研究了磷酸氢二钾对石墨炉原子吸收光谱法测定痕量镉的基体改进效应,试验表明,在磷酸盐存在下,镉的灰化温度能显著提高,钾对镉有一定的增感效应。以此建立了用磷酸氢二钾作基体改进剂,直接测定岩石、土壤和水系沉积物中痕量镉的方法。     

Atomic absorption spectrometric determination of calcium and other metallic elements in some animal protein sources

The phosphorus content of some animal protein sources was determined in order to identify the sample with the highest phosphorus content for use as a pilot sample. Varying concentrations of strontium and lanthanum were added to solutions of the ashed pilot sample for the determination of calcium and magnesium using flame atomic absorption spectrophotometry operated on the air-acetylene mode. At least 3000 ppm of strontium or lanthanum was required to completely overcome the interference of phosphate ion, PO(4)(3-), and give peak values for calcium. The presence of strontium or lanthanum did not affect the amount of magnesium obtained from the analyses. Based on this, a procedure is proposed and the results obtained by this procedure for calcium are more enhanced than those obtained without the addition of strontium or lanthanum for the same samples whereas comparable results were obtained for all other elements whether strontium or lanthanum was added or not. The method gives more accurate results and is reproducible. The coefficients of variation calculated using one of the samples were 0.58% for magnesium, 3.12% for zinc; 0.44% for calcium, 11.06% for lead, 22.22% for nickel, 3.53% for manganese and 3.50% for iron at the concentration levels found in that sample. Recoveries of spiked calcium, magnesium and zinc were quantitative. Also, for selected elements, results from the procedure compared well with those from chemical analysis.     

Automated headspace-solid-phase micro extraction-retention time locked-isotope dilution gas chromatography-mass spectrometry for the analysis of organotin compounds in water and sediment samples

An automated method for the simultaneous determination of six important organotin compounds namely monobutyltin (MBT), dibutyltin (DBT), tributyltin (TBT), monophenyltin (MPhT), diphenyltin (DPhT) and triphenyltin (TPhT) in water and sediment samples is described. The method is based on derivatization with sodium tetraethylborate followed by automated headspace-solid-phase micro extraction (SPME) combined with GC-MS under retention time locked (RTL) conditions. Home-synthesized deuterated organotin analogues were used as internal standards. Two high abundant fragment ions corresponding to the main tin isotopes Sn118 and Sn120 were chosen; one for quantification and one as qualifier ion. The method was validated and excellent figures of merit were obtained. Limits of quantification (LOQs) are from 1.3 to 15 ng l(-1) (ppt) for water samples and from 1.0 to 6.3 microg kg(-1) (ppb) for sediment samples. Accuracy for sediment samples was tested on spiked real-life sediment samples and on a reference PACS-2 marine harbor sediment. The developed method was used in a case-study at the harbor of Antwerp where sediment samples in different areas were taken and subsequently screened for TBT contamination. Concentrations ranged from 15 microg kg(-1) in the port of Antwerp up to 43 mg kg(-1) near a ship repair unit.     

Development of a new method for direct determination of selenium associated with atmospheric particulate matter using chemical modifiers and graphite probe furnace atomic absorption spectrometry

Direct determination of selenium on or in atmospheric particulate matter (APM) has been achieved using an integrated filtration and analysis system developed in our laboratories. The filtration (sampling) and analysis system consists of a porous electrographite plate which is used initially for the purpose of collecting APM and subsequently as a probe in graphite probe furnace atomic absorption spectrometry. Selenium produced a double peak when it was atomized from such an electrographite probe. Palladium nitrate+magnesium nitrate, as a mixed chemical modifier or ascorbic acid as a chemical modifier, eliminated the double peak. The addition of the chemical modifier(s) also removed the unpredictable changes in the peak-height and the peak-area absorbance which occurred from one atomization cycle to the next if the chemical modifier was not used. Precision of 5% RSD (peak-area absorbance) was obtained for an aqueous solution of selenium standard containing 1.25 ng of selenium with palladium nitrate+magnesium nitrate mixed chemical modifier, or ascorbic acid chemical modifer. The characteristic masses and the limits of detection for the aqueous solution of selenium standard with palladium nitrate+magnesium nitrate mixed chemical modifier are 27 and 41 pg (peak-area absorbance), respectively, and with ascorbic acid chemial modifier are 29 and 36 pg, respectively (peak-area absorbance). The results of analysis of the NIST (formerly National Bureau of Standards) Standard Reference Material No. 1648, Urban Particulate Matter, for selenium with palladium nitrate+magnesium nitrate mixed chemical modifier gave a recovery of 92%, and a precision of 10% RSD, and characteristic mass and the limit of detection of 20 and 37 pg, respectively.     

Ion-exchange of some elements in limestone, dolomite and chrome-iron ore

An ion-exchange procedure is described for the analysis of dolomite, limestone and chrome-iron ore. In dolomite and limestone, calcium and magnesium are separated by eluting with 1M acetate buffer (pH 6) ; in chrome-iron ore, chromium(VI) is first separated from other metals by passage through a cation-exchanger, Dowex 50W-X8 (H+ form), when chromium(VI) is not adsorbed. Iron, aluminium and magnesium are subsequently recovered from the resin and are determined by conventional methods.     

Spectrophotometric determination of chromium in waste water and soil

The reaction of Cr(VI) with o-nitrophenylfluorone (NPF) in presence of cetyltrimethyl-ammonium bromide (CTMAB) to form a purplish red complex at pH 4.7-6.6 by heating at 50 degrees for 10 min has been investigated. The composition of the complex is 1:2:2 [Cr(VI):NPF:CTMAB], the wavelength of maximum absorbance is 582 nm. The molar absorptivity is 1.11 x 10(5)1.mole(-1).cm(-1). Beer's law is obeyed up to 0.2 microg ml Cr(VI) concentration. The interference of several ions, including Cu(2+), Fe(3+) and Al(3+), is eliminated by addition of a masking mixture containing KF, DCTA and tartrate. A new sensitive method for determination of chromium in waste water and soil is presented.     

斜坡升温平台石墨炉法直接测葡萄酒中铅

研究了石墨炉法直接测定葡萄酒中铅的测定方法,以磷酸二氢氨－硝酸镁作基体改进剂,采用多步斜坡升温,恒温平台石墨炉技术测定了四个国家８种类别的葡萄酒中微量铅,回收率９６．０％～１０３．５％,ＲＳＤ３．２％,并采用国家标准物质ＧＢＷ０８５０３小麦粉制成悬浮液,验证了方法的准确度与重现性,结果满意。