Aptamer-based highly sensitive electrochemical detection of thrombin via the amplification of graphene

Herein, we successfully fabricated a highly sensitive label-free electrochemical aptasensor for thrombin based on the amplification of graphene (Gra). The excellent electrochemical probe of nickel hexacyanoferrate nanoparticles (NiHCFNPs) was introduced to form Nafion-Graphene-NiHCFNPs (Nf-Gra-NiHCFNPs) nanocomposites membrane on the gold electrode. The employment of graphene not only enhanced the surface area of the electrode with increased NiHCFNPs immobilization, but also improved the conductivity of the electrode, which further effectively improved the sensitivity of this proposed aptasensor. Subsequently, AuNPs layer was formed to immobilize the thrombin aptamer (TBA) and enhance the stability of the composite monolayer mentioned above. Then, thiol-modified TBA was assembled onto the AuNPs layer. Thereafter, hexanethiol (HT) was employed to block the possible remaining active sites. With the dual amplification of Gra and AuNPs, the resulting aptasensor exhibited good current response to target thrombin with a wide linear range extended from 1 pM to 80 nM (the detection limit was 0.3 pM). Additionally, the morphologies of bare Au substrate, nickel hexacyanoferrate nanoparticles (NiHCFNPs) and nanocomposites were successfully characterized by atomic force microscopy (AFM).     

A highly sensitive sensor for Cu2+ with unmodified gold nanoparticles and DNAzyme by using the dynamic light scattering technique

Copper ion (Cu(2+)) plays an important role in many biological reactions, and a suitable level of Cu(2+) is necessary for the regular metabolism of life. Thus developing a sensitive and simple method for determination of Cu(2+) is essential. Here, a novel and sensitive Cu(2+) sensor was developed based on detecting the average hydrodynamic diameter of AuNPs by using dynamic light scattering (DLS). Cu(2+)-specific DNAzyme was double-strand and could not adsorb on the surface of AuNPs, accordingly AuNPs aggregation would occur with the addition of NaCl. However, Cu(2+) could cleave DNAzyme and release single-stranded DNA (ssDNA) fragments, which could adsorb on the surface of AuNPs and prevent them from aggregation. Such differences in DNA adsorption ability on AuNPs before and after the addition of Cu(2+) affected the disperse state of AuNPs directly, and then affected their average hydrodynamic diameter, which could be detected with the DLS technique. Based upon the above mentioned principle, detection of Cu(2+) could be realized over the range from 100 pM to 2.0 nM, with a linear regression equation of D = 306.73 - 89.66C (C: nM, R = 0.9953) and a detection limit of 60 pM (3δ/slope). Moreover, satisfactory results were obtained when the assay was applied in the detection of Cu(2+) in water samples.     

MXene–AuNP-Based Electrochemical Aptasensor for Ultra-Sensitive Detection of Chloramphenicol in Honey

A simple and label-free electrochemical aptasensor was developed for ultra-sensitive determination of chloramphenicol (CAP) based on a 2D transition of metal carbides (MXene) loaded with gold nanoparticles (AuNPs). The embedded AuNPs not only inhibit the aggregation of MXene sheets, but also improve the quantity of active sites and electronic conductivity. The aptamers (Apts) were able to immobilize on the MXene–AuNP modified electrode surface through Au–S interaction. Upon specifically binding with CAP with high affinity, the CAP–Apt complexes produced low conductivity on the aptasensor surface, leading to a decreased electrochemical signal. The resulting current change was quantitatively correlated with CAP concentration. Under optimized experimental conditions, the constructed aptasensor exhibited a good linear relationship within a wide range of 0.0001–10 nM and with a low detection limit of 0.03 pM for CAP. Moreover, the developed aptasensor has been applied to the determination of CAP concentration in honey samples with satisfactory results.     

A Hairpin Electrochemical Aptasensor for Sensitive and Specific Detection of Thrombin Based on Homogenous Target Recognition

An electrochemical aptasensor was developed for sensitive and specific detection of thrombin by combining homogenous recognition strategy and gold nanoparticles (AuNPs) amplification. Streptavidin‐alkaline phosphatase was used as reporter molecule. Compared with the traditional hairpin aptasensor monitoring the distance of the redox molecule from the electrode surface, the proposed aptasensor successfully overcome the limitations of distance and improved the stability and high affinity of the aptamer hairpin through homogenous recognition, which enhanced the sensitivity and selectivity of the sensors effectively. Additionally, AuNPs were employed to increase the active area and conductivity of the electrode, thus, improving the sensitivity of the aptasensor. As a result, the designed thrombin detection sensor obtained a lower detection limit of 0.52 pM in buffer and 6.9 pM in blood serum.     

Electrochemical impedance spectroscopy detection of lysozyme based on electrodeposited gold nanoparticles

A simple, highly sensitive, and label-free electrochemical impedance spectroscopy (EIS) aptasensor based on an anti-lysozyme-aptamer as a molecular recognition element, was developed for the detection of lysozyme. Improvement in sensitivity was achieved by utilizing gold nanoparticles (AuNPs), which were electrodeposited onto the surface of a gold electrode, as a platform for immobilization of the aptamer. To quantify the amount of lysozyme, changes in the interfacial electron transfer resistance (R_et) of the aptasensor were monitored using the redox couple of an [Fe(CN)₆]^3−/4− probe. The R_et increased with lysozyme concentration. The plot of R_et against the logarithm of lysozyme concentration is linear over the range from 0.1 pM to 500 pM with a detection limit of 0.01 pM. The aptasensor also showed good selectivity for lysozyme without being affected by the presence of other proteins.     

A novel aptasensor based on 3D-inorganic hybrid composite as immobilized substrate for sensitive detection of platelet-derived growth factor

A novel electrochemical detection approach for platelet-derived growth factor(PDGF) via "sandwich"structure is reported in this paper. 3D-4MgCO_3 Mg(OH)_2 4H_2O-Au NPs inorganic hybrid composite was utilized as immobilized substrate for sensitive PDGF detection and Pt-Au bimetallic nanoparticles were labelled on PDGF aptamer to indirectly detect PDGF for the first time. The proposed aptasensor exhibited a high catalytic efficiency towards reduction of H_2O_2, hence the sensitive detection of PDGF was achieved.Results showed that the aptasensor exhibited excellent linear response to PDGF, in the range of 0.1 pg/m L–10 ng/m L(4 fmol/L–400 pmol/L), with detection limit of 0.03 pg/m L(1.2 fmol/L).     

Au/In2O3 Nanocubes Based Label-free Aptasensor for Ultrasensitive and Rapid Recognition of Cardiac Troponin I

Cardiac Troponin I (cTnI) is a preferred biomarker to diagnose acute myocardial infarction which is one of the leading risks to health globally due to its short term. However, clinical analyzers are difficult to achieve its on-site quantitative detection. A novel label-free aptasensor was constructed to realize ultrasensitive and rapid recognition of cTnI. A nanocubic AuNPs/In₂O₃ composite was designed to provide synergistic effects of abundant active sites and signal magnification for aptamers grafting. Relying on a conductance-dependence strategy, this aptasensor can achieve the quantitative detection within 10 min, which is much faster than state-of-the-art analyzers, as well as exhibiting an ultrawide linear range of 0.1–1000 ng/mL and a low detection limit of 0.06 ng/mL with an excellent selectivity in the analysis of human serum.     

A sensitive electrochemical aptasensor for ATP detection based on exonuclease III-assisted signal amplification strategy

A target-induced structure-switching electrochemical aptasensor for sensitive detection of ATP was successfully constructed which was based on exonuclease III-catalyzed target recycling for signal amplification. With the existence of ATP, methylene blue (MB) labeled hairpin DNA formed G-quadruplex with ATP, which led to conformational changes of the hairpin DNA and created catalytic cleavage sites for exonuclease III (Exo III). Then the structure-switching DNA hybridized with capture DNA which made MB close to electrode surface. Meanwhile, Exo III selectively digested aptamer from its 3′-end, thus G-quadruplex structure was destroyed and ATP was released for target recycling. The Exo III-assisted target recycling amplified electrochemical signal significantly. Fluorescence experiment was performed to confirm the structure-switching process of the hairpin DNA. In fluorescence experiment, AuNPs–aptamer conjugates were synthesized, AuNPs quenched fluorescence of MB, the target-induced structure-switching made Exo III digested aptamer, which restored fluorescence. Under optimized conditions, the proposed aptasensor showed a linear range of 0.1–20 nM with a detection limit of 34 pM. In addition, the proposed aptasensor had good stability and selectivity, offered promising choice for the detection of other small molecules.     

DNA Electrochemical Aptasensor for Detecting Fumonisins B1 Based on Graphene and Thionine Nanocomposite

In this paper, a novel aptasensor was designed by with the dual amplification of Au nanoparticles (AuNPs) and graphene/thionine nanocomposites (GS‐TH) for sensitive determination of fumonisins B₁ (FB₁). AuNPs is modified at the electrode surface to increase the electrical conductivity and fabricate specific recognition interface for FB₁ through the hybridization of capture DNA and its aptamer. Large number of TH molecules were loaded at the surface of graphene sheet to served as electrochemical probe and increase its electrochemical signal due to the excellent conductivity and large surface area of graphene sheet. This type of nanocomposites is then assembled to the single strand section of FB₁ aptamer at electrode surface by π–π stacking interactions between them, leading to an enhanced electrochemical signal. After the specific combination between FB₁ aptamer and its target (FB₁) in solution, GS–TH was released from electrode surface, resulting in a decreased electrochemical signal. The result demonstrated that the decreased currents were proportional to the FB₁ concentration in the range of 1–10⁶ pg/mL with a detection limit of 1 pg/mL. Besides, the developed aptasensor was also applied successfully for the determination of FB₁ in feed samples. The result shows this aptasensor has a higher sensitivity and selectivity.     

Label‐free Electrochemical Aptasensor for Carcino‐embryonic Antigen Based on Ternary Nanocomposite of Gold Nanoparticles,Hemin and Graphene

In this report, a label‐free electrochemical aptasensor for carcino‐embryonic antigen (CEA) was successfully developed based on a ternary nanocomposite of gold nanoparticles, hemin and graphene nanosheets (AuNPs‐HGNs). This nanocomposite was prepared by decorating gold nanoparticles on the surface of hemin functionalized graphene nanosheets via a simple wet‐chemical strategy. The aptamer can be assembled on the surface of AuNPs‐HGNs/GCE (glassy carbon electrode) through Au‐S covalent bond to form the sensing interface. Hemin absorbed on the graphene nanosheets not only acts as a protective agent of graphene sheets, but also as an in situ probe base on its excellent redox properties. Gold nanoparticles provide with both numerous binding sites for loading CEA binding aptamer (CBA) and good conductivity to promote the electron transfer. The current changes, which are caused by CEA specifically binding on the modified electrode, are exploited for the label‐free detection of CEA in a very rapid and convenient protocol. Therefore, the method has advantages of high sensitivity, wide linear range (0.0001–10 ng mL^?1), low detection limit (40 fg mL^?1) and attractive specificity. The results illustrate that the proposed label‐free electrochemical aptasensor has a potential application in the biological or clinical target analysis for its simple operation and low cost.     

Highly sensitive electrochemical label-free aptasensor based on dual electrocatalytic amplification of Pt-AuNPs and HRP

In this work, a label-free electrochemical aptamer-based sensor (aptasensor) was constructed on account of the direct immobilization of redox probes on an electrode surface. For this proposed aptasensor, a gold nanoparticles (AuNPs)-coated electrode was firstly modified with redox probes-nickel hexacyanoferrates nanoparticles (NiHCFNPs) through chemisorption and electrostatic adsorption. Then, platinum-gold alloy nanoparticles (Pt-AuNPs) and horseradish peroxidase (HRP) were respectively assembled onto the modified electrode surface, which formed the multilayer films for amplifying the electrochemical signal of NiHCFNPs and immobilizing thiolated thrombin aptamers (TBAs). In the presence of target thrombin, the TBA on the multilayer could catch the thrombin onto the electrode surface, which resulted in a barrier for electro-transfer, leading to the decrease of the electrochemical signal of NiHCFNPs amplified by the Pt-AuNPs and HRP toward H(2)O(2). The proposed method avoided the redox probes labeling process, increased the amount of redox probes, and further amplified the electrochemical signal. Thus, the approach showed a high sensitivity and a wider linearity to thrombin in the range between 0.01 nM and 50 nM with a detection limit of 6.3 pM.     

基于AuNPs/PDDA-GO纳米复合物的电化学免疫传感器的构建及对SirT1蛋白的检测

基于AuNPs/PDDA-GO纳米复合物制备了一种新型电化学免疫传感器, 并将其用于SirT1的检测. 首先, 在电极表面修饰复合材料AuNPs/PDDA-GO, 然后将目标蛋白SirT1固定到修饰了AuNPs/PDDA-GO的电极表面, 再通过特异性免疫反应结合一抗(Ab₁)和辣根过氧化酶标记的二抗分子(HRP-Ab₂), 最后用示差脉冲伏安法检测电流信号, 实现了对SirT1蛋白水平的测定. 在优化的实验条件下, SirT1蛋白的浓度在0.1~100 ng/mL范围内与响应电流呈良好线性关系, 检出限为0.029 ng/mL.     

A Sandwich‐type Electrochemiluminescence Aptasensor for Thrombin Based on Functional Co‐polymer Electrode Using Ru(bpy)32+ Doped Nanocomposites as Signal‐amplifying Tags

Herein, a signal‐on sandwich‐type electrochemiluminescence (ECL) aptasensor for the detection of thrombin (TB) was proposed. The graphene (GR) doped thionine (TH) was electropolymerized synchronously on the bare glassy carbon electrode (GCE) to form co‐polymer (PTG) electrode. The gold nanoparticles (AuNPs) were decorated on the surface of the PTG by in‐situ electrodeposition, and the functional co‐polymer (PTG‐AuNPs) electrode was utilized as sensing interface. Then, TB binding aptamer I (TBA I) as capture probes were modified on the PTG‐AuNPs electrode to capture TB, and Ru(bpy)₃²⁺/silver nanoparticles doped silica core‐shell nanocomposites‐labeled TB binding aptamer II (RuAg/SiO₂NPs@TBA II) were used as signal probes to further bind TB, resulting in a sandwich structure. With the assistant of silica shell and AgNPs, the enrichment and luminous efficiency of Ru(bpy)₃²⁺ were significantly improved. Under the synergy of PTG‐AuNPs and RuAg/SiO₂NPs, the ECL signal was dramatically increased. The proposed ECL aptasensor displayed a wide linear range from 2 fM to 2 pM with the detection limit of 1 fM, which is comparable or better than that in reported ECL aptasensors for TB using Ru(bpy)₃²⁺ and its derivatives as the luminescent substance. The excellent sensitivity makes the proposed aptasensor a promising potential in pharmaceutical and clinical analysis.     

Amperometric sandwich-type aptasensor based on peroxidase mimetic Au@Pt for the carcinoembryonic antigen

For sensitive analysis of cancer biomarker carcinoembryonic antigen (CEA), an amperometric sandwich-type aptasensor is proposed based on a signal amplification strategy of Au@Pt bimetallic nanoprobes. As the excellent catalytic activity to hydrogen peroxide (H₂O₂), core-shell Au@Pt nanoparticles are employed as nanoprobes by conjugating directly with the secondary aptamer of CEA (Apt-II). Due to the synergic recognition effect of dual aptamers and the excellent catalytic activity of nanoprobes, this amperometric sandwich-type aptasensor for CEA exhibits high specificity and good sensitivity with a limit of detection of 0.31 ng/mL, along with a wide linear range from 0.1 ng/mL to 100 ng/mL.     

Coordination of mercury(II) to gold nanoparticle associated nitrotriazole towards sensitive colorimetric detection of mercuric ion with a tunable dynamic range

A simple colorimetric assay with high sensitivity, excellent selectivity and a tunable dynamic range is reported for detecting trace amounts of mercuric ion in aqueous solution based on the coordination of Hg(2+) to the gold nanoparticle (AuNP)-associated 3-nitro-1H-1,2,4-triazole (NTA). The NTA can stabilize the AuNPs against tris-induced aggregation through capping the AuNPs. In the presence of Hg(2+), the NTA is released from the AuNP surface via the formation of a NTA-Hg(2+) coordination complex, leading to the aggregation of AuNPs in tris. This detection strategy is unique in terms of high sensitivity and excellent selectivity, a tunable dynamic range, and simplicity of probe preparation. Low detection limits of 7 nM (1.4 ppb) and 50 nM (10 ppb) can be achieved by spectrophotometer and by direct visualization, respectively, under the optimized conditions. No noticeable colour changes are observed towards other metal ions (Ag(+), Zn(2+), Ni(2+), Cr(3+), Mg(2+), Cu(2+), Co(2+), Cd(2+), Pb(2+), Fe(2+)) at concentrations up to 100 μM without the need of any other masking agents. In addition, the dynamic range of the assay can be easily tuned by adjusting the amount of NTA in the NTA-AuNP probes. More importantly, the NTA-AuNP probes can be simply prepared by mixing NTA with as-synthesized citrate-capped AuNPs. This not only avoids complicated surface modifications and tedious separation processes, but also is cost-effective.     

Label-free aptasensor for thrombin using a glassy carbon electrode modified with a graphene-porphyrin composite

We report on an electrochemical aptasensor for the ultrasensitive determination of thrombin. A glassy carbon electrode modified with a graphene-porphyrin nanocomposite exhibits excellent electrochemical activity and can be used as a redox probe in differential pulse voltammetry of the porphyrin on its surface. The thrombin aptamer is then immobilized via p-stacking interactions between aptamer and graphene and π-π stacking with porphyrin simultaneously. The resulting electrochemical aptasensor displays a linear response to thrombin in the 5–1,500 nM concentration range and with a limit of detection of 0.2 nM (at an S/N of 3). The sensor benefits from the synergetic effects of graphene (with its high conductivity and high surface area), of the porphyrin (possessing excellent electrochemical activity), and of the aptamer (with its high affinity and specificity). This kind of aptasensor conceivably represents a promising tool for bioanalytical applications.

A Sensitive Signal-off Electrochemical Aptasensor for Thrombin Detection using PB−Au@MoS2 Nanomaterial as Both Platform and Signal Reporter

Human serum is one of the effective samples for point-of-care testing (POCT). Sensitive and quick determination of thrombin content in human serum samples is important. An electrochemical aptasensor based on Prussian blue and Au nanoparticles loaded MoS₂ nanoflowers (PB−Au@MoS₂) hybrid was constructed. By using PB−Au@MoS₂ as both a substrate and a signal reporter, this aptasensor could demonstrate excellent performance for thrombin detection with a detection linear range from 0.01 pM to 30 nM and detection limit down to 1 fM. This work may provide a strategy to establish effective and sensitive sensing devices for thrombin in clinical diagnosis.     

纳米金信号探针/石墨烯修饰免疫传感器检测微囊藻毒素

利用石墨烯纳米片层(GS)偶联牛血清白蛋白(BSA)标记的微囊藻毒素(MCLR)(BSA-MCLR)构建了纳米金(Au NPs)为信号探针的电流型免疫传感器。分别用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和紫外-可见吸收光谱对合成纳米材料进行表征;用循环伏安法研究修饰电极表面的电化学特性。通过待测MCLR与固定的BSA-MCLR竞争结合抗体(anti-MCLR),之后恒电位将Au NPs氧化为Au Cl-4,再利用差分脉冲伏安法(DPV)进行阴极电位扫描,还原Au Cl-4为Au,以产生的峰电流值为检测信号,测定MCLR浓度。最佳实验条件下,用免疫传感器测定MCLR的线性范围为0.1~50μg/L,检出限为0.05μg/L。对传感器的重现性、稳定性和选择性进行了考察。相较于酶标探针,以Au NPs为信号探针标记抗体,可使检测过程更经济便捷,稳定性更强,检测效果良好。     

Gold-dendrimer Nanocomposite Based Electrochemical Sensor for Dopamine

An electrochemical sensor for dopamine was developed by electrodepositing poly(propylene imine) (PPI) dendrimer and gold nanoparticles (AuNPs) onto a glassy carbon electrode (GCE). Electrochemical characterisation of the sensor was carried out by cyclic voltammetry and electrochemical impedance spectroscopy in ferri/ferrocyanide electrolyte. The nanocomposite electrode (GCE-PPI-AuNPs) showed improved electroactive surface area and electrochemical response over bare GCE. The sensor recorded a detection limit of 0.16 μM over a concentration range of 0.1 μM to 125 μM. The sensor was applied for dopamine detection in human serum samples and in the presence of interfering substances such as ascorbic acid and epinephrine.     

Ultrasensitive electrochemical biosensor for uranium using deoxyribozymes with amplification by gold nanoparticles

A novel highly sensitive and specific electrochemical biosensor for detecting uranium based on specific Deoxyribozymes and gold nanoparticles (AuNPs) is reported. In this work, AuNPs provide excellent electrochemical signal transduction and a large surface area for immobilising numerous Deoxyribozymes, so a low detection limit of 3.24 ng L^?1 uranium and a good linear relationship over the range 5.94–35.1 ng L^?1 (r = 0.994) were obtained. The proposed biosensor presents high specificity and selectivity for uranium and is not affected by other metal ions. Thus, the biosensor protocol offers good selectivity, rapid speed and operational convenience for detection uranium in liquid waste.