Natural dye-based photoelectrode for improvement of solar cell performance

In the present paper, photovoltaic studies of dye-sensitized solar cells (DSSCs) based on betacyanin/TiO₂ and betacyanin/WO₃–TiO₂ have been done. The cell performances were compared through I–V curves and wavelength dependant photocurrent measurements for the two new types of DSSCs. The TiO₂-coated DSSC showed the photovoltage and photocurrent of 300 mV and 4.96 mA/cm², whereas the cell employing WO₃–TiO₂ photoelectrode showed the values 435 mV and 9.86 mA/cm², respectively. The conversion efficiency of TiO₂ based dye-sensitized solar cell was found to be 0.69 %, while WO₃–TiO₂-based cell exhibited a higher conversion efficiency of 2.2 %. The better performance of the WO₃–TiO₂ dye-sensitized solar cell photoelectrode is thought to be due to an inherent energy barrier at the electrode/electrolyte interface leading to the reduced recombination of photoinduced electrons.     

Poly(vinyl chloride)-<Emphasis Type="Italic">graft</Emphasis>-poly(<Emphasis Type="Italic">N</Emphasis>-vinyl caprolactam) graft copolymer: synthesis and use as template for porous TiO<Subscript>2</Subscript> thin films in dye-sensitized solar cells

Poly(N-vinyl caprolactam) (PNVCL) side chains were grafted to a poly(vinyl chloride) (PVC) backbone via atom transfer radical polymerization. The synthesized PVC-g-PNVCL graft copolymer was templated for the preparation of porous TiO₂ thin films, which involved a sol–gel reaction and calcination process. The interaction of the carbonyl groups in the PVC-g-PNVCL with the titania was revealed by FT-IR spectroscopy. X-ray diffraction and transmission electron microscopy analysis showed the formation of porous TiO₂ thin films with the anatase phase. A series of porous TiO₂ thin films with different pore sizes and porosities was prepared by varying the solution compositions and were used as photoelectrodes in dye-sensitized solar cells (DSSC) with a polymer electrolyte. The DSSC performed best when using the TiO₂ film with higher porosity, lower interfacial resistance, and longer electron life time. The highest energy conversion efficiency, photovoltage (V _oc), photocurrent density (J _sc), and fill factor (FF) were 1.2%, 0.68 V, 3.2 mA/cm², and 0.57 at 100 mW/cm², respectively, for the quasi-solid state DSSC with a 730-nm-thick TiO₂ film.     

TiO2 treatment using ultrasonication for bubble cavitation generation and efficiency assessment of a dye-sensitized solar cell

In this study, the impacts of different ultrasonic treatments on TiO₂ particles were determined and they were used to manufacture the photoelectrodes of a dye-sensitized solar cell (DSSC). Two methods were used to prepare TiO₂ particles directly sonicated by an ultrasonic horn, and TiO₂ treated indirectly by an ultrasonic cleaner. TEM, XPS analysis was confirmed that cavitation bubbles generated during ultrasonication resulted in defects on the surface of TiO₂ particles, and the defect induced surface activation. To understand the effect of TiO₂ surface activation on energy conversion efficiency of DSSC, ultrasonic horn DSSC and ultrasonic cleaner DSSC were prepared. The UV–vis analysis exhibited that the ultrasonic horn DSSC possessed higher dye adsorption when compared to the ultrasonic cleaner DSSC, and the EIS analysis confirmed that the electron mobility was greatly increased in the ultrasonic horn DSSC. The energy conversion efficiency of the ultrasonic horn DSSC was measured to be 3.35%, which is about 45% increase in comparison to that of the non-ultrasonic treated DSSC (2.35%). In addition to this regard, recombination resistance of ultrasonic horn DSSC was calculated to be 450 Ω·cm², increasing more than two times compared to the non-ultrasonic treated DSSC (200 Ω·cm²). Taken together, these ultrasonic treatments significantly improved the energy conversion efficiency of DSSC, which was not tried in DSSC-related research, and might lead us to develop more efficient practical route in the manufacturing of DSSC.     

Dye-sensitized solar cells based on ZnO nanowire array/TiO2 nanoparticle composite photoelectrodes with controllable nanowire aspect ratio

The ZnO nanowire (NW) array/TiO₂ nanoparticle (NP) composite photoelectrode with controllable NW aspect ratio has been grown from aqueous solutions for the fabrication of dye-sensitized solar cells (DSSCs), which combines the advantages of the rapid electron transport in ZnO NW array and the high surface area of TiO₂ NPs. The results indicate that the composite photoelectrode achieves higher overall photoelectrical conversion efficiency (η) than the ZnO NW alone. As a result, DSSCs based on the ZnO NW array/TiO₂ NP composite photoelectrodes get the enhanced photoelectrical conversion efficiency, and the highest η is also achieved by rational tuning the aspect ratio of ZnO NWs. With the proper aspect ratio (ca. 6) of ZnO NW, the ZnO NW array/TiO₂ NP composite DSSC exhibits the highest conversion efficiency (5.5 %). It is elucidated by the dye adsorption amount and interfacial electron transport of DSSCs with the ZnO NW array/TiO₂ NP composite photoelectrode, which is quantitatively characterized using the UV-Vis absorption spectra and electrochemical impedance spectra. It is evident that the DSSC with the proper aspect ratio of ZnO NW displays the high dye adsorption amount and fastest interfacial electron transfer.     

Electrostatic assembly of CdTe quantum dots with different charged ligands into TiO2 porous film for solar cells

We have demonstrated an approach for the electrostatic assembly of CdTe quantum dots (QDs) with different charged ligands as sensitizers, achieving high coverage and good dispersion in TiO₂ porous films. The CdTe QD-sensitized TiO₂ porous films were subjected to thermal annealing in a high vacuum chamber to remove the ligand linker, resulting in the formation of direct heterojunctions between the bare CdTe QDs and TiO₂ for a favorable charge transfer. The as-received CdTe QD-sensitized TiO₂ porous films were employed as photoanodes for quantum dot-sensitized solar cells (QSSCs), and the photocurrent density reached as high as 4.69 mA/cm² under a standard illumination condition of simulated AM 1.5G (100 mW/cm²).     

A facile low temperature synthesis of TiO2 nanorods for high efficiency dye sensitized solar cells

Titania (TiO₂) nanorods have been synthesized with controlled size for dye-sensitized solar cells (DSSCs) via hydrothermal route at low hydrothermal temperature of 100 °C for 24 h. The titania nanorods were characterized using XRD, SEM, TEM/HRTEM, UV-vis Spectroscopy, FTIR and BET specific surface area (S _BET), as well as pore-size distribution by BJH. The results indicated that the bulk traps and the surface states within the TiO₂ nanorods films have enhanced the efficiency of DSSCs. The size of the titania nanorods was 6.7 nm in width and 22 nm in length. The high surface area can provide more sites for dye adsorption, while the fast photoelectron-transfer channel can enhance the photogenerated electron transfer to complete the circuit. The specific surface area S _BET was 77.14 m²?g^?1 at the synthesis conditions. However, the band gap energy of the obtained titania nanorods was 3.2 eV. The oriented nanorods with appropriate lengths are beneficial in improving the electron transport property and thus leading to the increase of photocurrent, together enhancing the power conversion efficiency. A nearly quantitative absorbed photon-to-electrical current conversion achieved upon excitation at wave length of 550 nm and the power efficiency was enhanced from 5.6 % for commercial TiO₂ nanoparticles Degussa (P25) cells to 7.2 % for TiO₂ nanorods cells under AM 1.5 illumination (100 mW?cm^?2). The TiO₂ cells performance was improved due to their high surface area, hierarchically mesoporous structures and fast electron-transfer rate compared with the Degussa (P25).     

Dye sensitized solar cells prepared by flames stabilized on a rotating surface

A previously developed flame synthesis method was applied to the preparation of mesoporous titania films for application in dye sensitized solar cells (DSSC). The method combines the synthesis of narrowly sized, ultrafine metal oxide particles with controllable chemical and phase purity and the deposition of these particles into a uniform, porous thin film in a single step. The current work used a series of ethylene–oxygen–argon flames to produce DSSC anode films of wide ranging properties. The performance of the solar cells prepared with these anode films was studied at the fundamental level with respect to variations of the titania crystal phase purity and content resulting from changes primarily from flame stoichiometry changes. Based on the basic relationship established among flame synthesis condition-material property-cell performance, a highly efficient DSSC was designed, which shows photocurrent densities better than some of the best performing cells reported to date. Additional studies have focused on a demonstration of the suitability of the flame process in engineering TiO₂ films structurally and chemically with the potential of further improved DSSC efficiency.     

Performance and stability studies of inverted polymer solar cells with TiO2 film as a buffer layer

TiO₂ based inverted polymer solar cells (PSCs) with a structure of fluorine-doped tin oxide (FTO)/TiO₂/P3HT:PCBM/PEDOT:PSS/Ag presented excellent air stabilities,; the power conversion efficiency (PCE) of devices exhibited only 15 % decay as compared to the highest value while being exposed in air-condition for more than 20 days. Interestingly, an overall enhancement of PCE from 3.5 % to 3.9 % was observed while the PSCs were exposed in air-condition up to 3 days; the improvement of performance was attributed to the TiO₂ films’ oxygen and water protection effect and the oxidation of Ag, which will benefit to form an effective work function match with the HOMO of P3HT leading to improved ohmic contact. However, the performance slowly decreased when the exposure time remains longer due to the physical adsorbed oxygen. UV–ozone treatment on the TiO₂ films’ leads to the formation of a metal-deficient oxide that results in a decreased PCE for the devices. Finally, X-ray photo-emission spectroscopy (XPS) was used to analyze the compositional changes of the TiO₂ films while they were exposed in air-condition or treated by UV–ozone.     

Effects of Gd<Superscript>3+</Superscript> modifications on the photoelectrochemical properties of TiO<Subscript>2</Subscript>-based dye-sensitized solar cells

In this paper, TiO₂ particles (~30 nm) modified with Gd₂O₃-coating layer (~2 nm) for dye-sensitized solar cells (DSSCs) were fabricated via the hydrothermal method. Among the solar cells based on the Gd³⁺-doped TiO₂ photoanodes, the optimal conversion efficiency was obtained from the 0.025Gd³⁺-modified TiO₂-based cell, with a 17.7% improvement in the efficiency as compared to the unmodified one (7.18%). This enhancement was probably due to the improved UV radiation harvesting via a down-conversion luminescence process by Gd³⁺ ions, enhancement of visible light absorption and improved dye loading capacity. In addition, after Gd modification, a thin coating could be formed on the TiO₂ nanoparticles, which worked as an energy barrier and resulted in a lower charge recombination.     

Synthesis of two-dimensional nanowall of Cu-Doped TiO2 and its application as photoanode in DSSCs

Two-dimensional nanowall of Cu-doped TiO₂ (CuTNW) has been prepared in this work to study the role of Cu doping on its photoactivity properties and its photovoltaic performance as photoanode in a dye-sensitized solar cell (DSSC). TiO₂ nanowall with five Cu ion doping, i.e. 6.25, 12.5, 25.0, 50.0 and 100.0 mM, were prepared via a liquid-phase deposition method using ammoniumhexafluorotitanate and hexamethylenetetramine as the reagents with a growth temperature of 90 °C. The X-Ray Diffraction (XRD), X-ray energy dispersion (EDX) and diffuse optical reflectance spectroscopy analysis results confirmed the successfulness of the Cu doping process in the TiO₂ nanowall and effective modification on the photoactivity of the TiO₂ nanowall. We found that the power conversion efficiency of the DSSC utilizing TiO₂ nanowall as photoanode can be enhanced up to 2 times, i.e. from 0.2% to 0.44%, when the TiO₂ nanowall doped with Cu ion. The nanostructure preparation, device fabrication and the mechanism for the device performance enhancement will be discussed.     

Fabrication of hydrophobic surface of titanium dioxide films by successive ionic layer adsorption and reaction (SILAR) method

Titanium dioxide (TiO₂) films were fabricated on fluorine doped tin oxide (FTO) coated glass substrate using successive ionic layer adsorption and reaction (SILAR) method. The X-ray diffraction, scanning electron microscopy, transmission electron microscopy, optical absorption and contact angle measurement were applied to study the structural, surface morphological, optical and surface wettability properties of the as-deposited and annealed TiO₂ films. The X-ray diffraction studies revealed both as-deposited and annealed TiO₂ films are amorphous. Irregular shaped spherical grains of random size and well covered to the fluorine doped tin oxide coated glass substrates were observed from SEM studies with some cracks after annealing. The optical band gap values of virgin TiO_2, annealed, methyl violet and rose bengal sensitized TiO₂ were found to be 3.6, 3.5, 2.87 and 2.95 eV, respectively. Surface wettability studied in contact with liquid interface, showed hydrophobic nature as water contact angles were greater than 90°. The adsorption of dyes, as confirmed by the photographs, is one of the prime requirements for dye sensitized solar cells (DSSC).     

Dye-sensitized solar cells fabricated with black raspberry, black carrot and rosella juice

In this work, dye sensitized solar cells (DSSC’s) were constructed from black raspberry (Rubus Ideaus), black carrot (Daucuscarota L.) and rosella juice (Hibiscus Sabdariffa L.). In order to fabricate a DSSC the fluorine-doped tin (IV) oxide (FTO) thin films obtained by using spray pyrolysis technique were used as a substrate. TiO₂ films on FTO layers were prepared by doctor-blading technique. Platinum-coated counter electrode and liquid Iodide/Iodine electrolyte solution were used to fabricate DSSC’s. The efficiencies of solar cells produced with black carrot, rosella and black raspberry juice were calculated as 0.25%, 0.16% and 0.16% respectively, under a sunny day in Kahramanmaraş-Turkey.     

Utilization of saffron (<Emphasis Type="Italic">Crocus sativus L.</Emphasis>) as sensitizer in dye-sensitized solar cells (DSSCs)

Photoelectrodes of dye-sensitized solar cells (DSSCs) have been prepared using nanosized titanium dioxide that have soaked in a solution of different saffron (Crocus sativus L.) spice content in ethanol. The optimized polyacrylonitrile (PAN)-based gel polymer electrolyte with 40.93 wt.% ethylene carbonate, 37.97 wt.% propylene carbonate, 4.37 wt.% tetrapropylammonium iodide, 9.86 wt.% PAN, 1.24 wt.% 1-butyl-3-methylimidazolium iodide, 4.35 wt.% lithium iodide and 1.28 wt.% iodine has been used as the electrolyte for DSSC. The electrolyte has conductivity of 2.91 mS cm^?1 at room temperature (298 K). DSSCs were also sensitized with saffron solution that has been added with 30 wt.% chenodeoxycholic acid (CDCA) co-adsorbent and designated as DSSC P4. The solar cell converts light-to-electricity at an efficiency of 0.31%. This is 29% enhancement in efficiency for the DSSC without addition of CDCA in the saffron-ethanol solution. The DSSC exhibits current density at short-circuit (J _sc ) of 1.26 mA cm^?2, voltage at open circuit (V _oc ) of 0.48 V and 51% fill factor. DSSC P4 also exhibits the highest incident photon-to-current density of more than 40% at 340 nm wavelength.     

Characterization techniques of sandwich-type TiO2/QD composites for low-cost quantum dots' solar cell

There is a high impact of the solar cells on energy manufacturing. For several years the energy efficiency was limited due to base-materials' structural and technological limits. High increase of energy harvesting of solar cells has been observed since the first solar cell based on dye-sensitized colloidal TiO₂ films occurred. One of the most promising solutions are used quantum dots (QD) for light energy conversion. In this paper, we described the use of selected characterization techniques for sandwich-type TiO₂/QD composites for a low-cost quantum dots' solar cell in the point of view of mass manufacturer of solar cells and research and development laboratory. Moreover, the increasing role of Raman spectroscopy and mapping for the TiO₂/QD was presented and compared with other necessity techniques for solar cell investigations such as ellipsometry, atomic force microscopy (AFM), and secondary ion mass spectrometry (SIMS).     

Effect of annealing treatment on the uniformity of CeO2/TiO2 bilayer resistive switching memory devices

Bilayer CeO₂/TiO₂ films with high-k dielectric property were prepared by rf magnetron sputtering technique at room temperature. Effect of annealing treatment on resistive switching (RS) properties of bilayer CeO₂/TiO₂ films in O₂ ambient at different temperature in the range of 350–550 °C was investigated. Our results revealed that the bilayer films had good interfacial property at 500 °C and this annealing temperature is optimum for different RS characteristics. Results showed that bilayer CeO₂/TiO₂ film perform better uniformity and reliability in resistive switching at intermediate temperature (i.e. 450 °C and 500 °C) instead of low and high annealing temperature (i.e. 350 °C and 550 °C) at which it exhibits poor crystalline structure with more amorphous background. Less Gibbs free energy of TiO₂ as compared to CeO₂ results in an easier re-oxidation of the filament through the oxygen exchange with TaN electrode. However, the excellent endurance property (>2500 cycles), data retentions (10⁵ s) and good cycle-to-cycle uniformity is observed only in 500 °C annealed devices. The plots of cumulative probability, essential memory parameter, show a good distribution of Set/Reset voltage.     

One-pot,large-scale synthesis silica-encapsulated NIR alloy quantum dots CdSeTe within short time

Hydrothermal process has been employed to synthesize titanium oxide (TiO₂) bottle brush. The nanostructured bottle brushes with tetragonal nanorods of ~75 nm diameter have been synthesized by changing the nature of the precursors and hydrothermal processing parameters. The morphological features and structural properties of TiO₂ films were investigated by field emission scanning electron microscopy, X-ray diffraction, high-resolution transmission electron spectroscopy, Fourier transform Raman spectroscopy, and X-ray photoelectron spectroscopy. The influence of such nanostructures on the performance of dye-sensitized solar cells (DSSCs) is investigated in detail. The interface and transient properties of these nanorods and bottle brush-based photoanodes in DSSCs were analyzed by electrochemical impedance spectroscopic measurements in order to understand the critical factors contributing to such high power conversion efficiency. Surface area of sample was recorded using Brunauer–Emmett–Teller measurements. It is found that bottle brush provides effective large surface area 89.34 m² g^?1 which is much higher than TiO₂ nanorods 63.7 m² g^?1. Such effective surface area can facilitate the effective light harvesting, and hence improves the dye adsorption and the photovoltaic performance of DSSCs, typically in short-circuit photocurrent and power conversion efficiency. A best power conversion efficiency of 6.63 % has been achieved. We believe that the present device performance would have wide interests in dye-sensitized solar cell research.     

Influence of pyrazole on the photovoltaic performance of dye-sensitized solar cell with polyvinylidene fluoride polymer electrolytes

We investigate the influence of the pyrazole content on the polyvinylidene fluoride (PVDF)/KI/I₂ electrolytes for dye-sensitized solar cells (DSSCs). The solid polymer electrolyte films consisting of different weight percentage ratios (0 20, 30, 40, and 50 %) of pyrazole doped with PVDF/KI/I₂ have been prepared by solution casting technique using N,N-dimethyl formamide (DMF) as a solvent. The as-prepared polymer electrolyte films were characterized by various techniques such as Fourier transform infrared spectroscopy (FT-IR spectroscopy), differential scanning calorimetry (DSC), X-ray diffractometer (XRD), alternate current (AC)-impedance analysis, and scanning electron microscopy (SEM). The 40 wt% pyrazole-PVDF/KI/I₂ electrolyte exhibited the highest ionic conductivity value of 9.52?×?10^?5 Scm^?1 at room temperature. This may be due to the lower crystallinity of PVDF and higher ionic mobility of iodide ions in the electrolyte. The DSSC fabricated using this highest ion conducting electrolyte showed an enhanced power conversion efficiency of 3.30 % under an illumination of 60 mW/cm² than that of pure PVDF/KI/I₂ electrolyte (1.42 %).     

Structural properties of single and multilayer ITO and TiO2 films deposited by reactive pulsed laser ablation deposition technique

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser. The films were deposited on SiO₂ substrates heated at 200 and 400 °C. ITO and TiO₂ films with uniform thicknesses of about 400 and 800 nm, respectively, over large areas were prepared. X-ray diffraction (XRD) analysis revealed that the ITO films are formed of highly orientated nanocrystals with an average particle size of 10-15 nm. Atomic force microscopy (AFM) observations indicate rough ITO films surfaces with average roughness of 26-30 nm. Pores were also observed. TiO₂ films deposited on the prepared ITO films result less crystalline. Annealing at 300 and 500 °C for three consecutive hours promoted formation of TiO₂ anatase phase, with crystal size of ∼6-7 nm. From the scanning transmission electron microscope (STEM) images, it can be seen that the TiO₂ films deposited onto the prepared ITO films present a relatively high pore sizes with an average pore diameter of ∼40 nm and excellent uniformity. In addition, STEM cross-sectional analysis of our films showed a columnar structure but no evidence of voids in the structure. Therefore, films exhibited large surface area, well suited for dye-sensitized solar cells (DSSC) applications.     

A novel TiO2 nanoparticles/nanowires composite core with ZrO2 nanoparticles shell coating photoanode for high-performance dye-sensitized solar cell based on different electrolytes

The novel TiO₂ nanopartilces/nanowires (TNPWs) composite with ZrO₂ nanoparticles (ZNPs) shell-coated photoanodes were prepared to fabricate high-performance dye-sensitized solar cell (DSSC) based on different types of electrolytes. Hafnium oxide (HfO₂) is a new and efficient blocking layer material applied over the TNPWs-ZNPs core-shell photoanode film. TiO₂ nanoparticles (TNPs) and TiO₂ nanowires (TNWs) were characterized by X-ray diffractometer (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). DSSCs were fabricated using the novel photoanodes with an organic sensitizer D149 dye and different types of electrolytes namely liquid electrolyte, ionic liquid electrolyte, solid-state electrolyte, and quasi-solid-state electrolyte. The DSSC-4 made through the novel core-shell photoanode using quasi-solid-state electrolyte showed better photocurrent efficiency (PCE) as compared to the other DSSCs. It has such photocurrent-voltage characteristics: short circuit photocurrent (Jsc)?=?19 mA/cm², the open circuit voltage (Voc)?=?650 mV, fill factor (FF)?=?65 %, and PCE (η)?=?8.03 %. The improved performance of DSSC-4 is ascribed to the core-shell with blocking layer photoanode could increased electron transport and suppressed recombination of charge carriers at the TNPWs-ZNPs/dye/electrolyte interface.     

Magnetic carbon nanotubes: synthesis by a simple solvothermal process and application in magnetic targeted drug delivery system

A poly(vinyl chloride) (PVC) main chain was grafted with poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) containing a quaternary amine group using atom transfer radical polymerization. The successful synthesis of a PVC-g-PDMAEMA graft copolymer was confirmed by Fourier transform infrared, nuclear magnetic resonance, thermogravimetric analysis, and transmission electron microscopy. The PVC-g-PDMAEMA graft copolymer was used as a structure-directing agent (SDA) for the fabrication of a mesoporous thin film containing a titanium dioxide (TiO₂) layer. To control the porosity of the resultant inorganic layer, the ratio of SDA to TTIP as well as the concentration of the sol?Cgel was varied. The structure and porosity of the mesoporous film were characterized by XRD and SEM analysis. The mesoporous TiO₂ film fabricated on the FTO surface was used as a photoanode for the dye-sensitized solar cell (DSSC). DSSC performance was the greatest when using TiO₂ film with a higher porosity and lower interfacial resistance. The highest energy conversion efficiency reached 3.2?% at 100?mW/cm², which was one of the highest reported values for a quasi-solid-state DSSC with 600-nm-thick TiO₂ film.