气质联用仪法测定奶粉中多环芳烃

研究了奶粉中多环芳烃的气相色谱/质谱(GC/MS)测定方法. 样品经甲醇-KOH皂化后用甲苯提取, 提取液经微孔滤膜过滤后用气相色谱质谱仪测定其含量, 外标法定量. 结果16种PAHs的回收率范围为92.0%～106%;RSD为2.2%～4.7%. 方法能同时分离16种PAHs, 适合于奶粉中多环芳烃的分析测定.     

Determination of polycyclic aromatic hydrocarbons in honey by matrix solid-phase dispersion and gas chromatography/mass spectrometry

A multiresidue method was developed for the de termination of 16 polycyclic aromatic hydrocarbons (PAHs) in unifloral and multifloral honeys. The analytical procedure is based on the matrix solid-phase dispersion of honey on a mixture of Florisil and anhydrous sodium sulfate in small glass columns and extraction with hexane-ethyl acetate (90 + 10, v/v) with assisted sonication. The PAH residues are determined by gas chromatography with mass spectrometric detection using selected-ion monitoring. Average recoveries for all the PAHs studied were in the range of almost 80 to 101%, with relative standard deviations of 6 to 15%. The limits of detection ranged from 0.04 to 2.9 microg/kg. The simultaneous extraction and cleanup of samples makes this method simple and rapid, with low consumption of organic solvents     

快速溶剂萃取-气相色谱-串联质谱法分析海洋沉积物中16种多环芳烃

建立了快速溶剂萃取（ASE）-气相色谱-串联质谱（GC-MS/MS）分析海洋沉积物中16种多环芳烃（PAHs）的分析方法。样品由正己烷-丙酮（1∶1,v/v）溶液萃取,经无水硫酸钠脱水、氮吹浓缩后,采用硅胶固相萃取小柱进行净化,然后经HP-5MS色谱柱（30 m×0.25 mm×0.25 μm）分离,在电子轰击电离源下以多反应监测（MRM）模式进行检测,内标法定量。分析结果表明,16种PAHs在0.01~1.00 mg/L范围内线性关系良好,相关系数（R）大于0.997;目标物的加标回收率为75.8%~97.8%;日内与日间精密度（RSD）均小于10%。当取样量为20.0 g时,16种PAHs的方法检出限为0.048~0.234 μg/kg。该法快速、准确、稳定,能够满足海洋沉积物中痕量PAHs的测定。     

Determination of chlorinated polycyclic aromatic hydrocarbons in water by solid‐phase extraction coupled with gas chromatography and mass spectrometry

Given the potential risks of chlorinated polycyclic aromatic hydrocarbons, the analysis of their presence in water is very urgent. We have developed a novel procedure for determining chlorinated polycyclic aromatic hydrocarbons in water based on solid‐phase extraction coupled with gas chromatography and mass spectrometry. The extraction parameters of solid‐phase extraction were optimized in detail. Under the optimal conditions, the proposed method showed wide linear ranges (1.0–1000 ng/L) with correlation coefficients ranging from 0.9952 to 0.9998. The limits of detection and the limits of quantification were in the range of 0.015–0.591 and 0.045–1.502 ng/L, respectively. Recoveries ranged from 82.5 to 102.6% with relative standard deviations below 9.2%. The obtained method was applied successfully to the determination of chlorinated polycyclic aromatic hydrocarbons in real water samples. Most of the chlorinated polycyclic aromatic hydrocarbons were detected and 1‐monochloropyrene was predominant in the studied water samples. This is the first report of chlorinated polycyclic aromatic hydrocarbons in water samples in China. The toxic equivalency quotients of chlorinated polycyclic aromatic hydrocarbons in the studied tap water were 9.95 ng the toxic equivalency quotient m^?3. 9,10‐Dichloroanthracene and 1‐monochloropyrene accounted for the majority of the total toxic equivalency quotients of chlorinated polycyclic aromatic hydrocarbons in tap water.     

Identification of oxygenated polycyclic aromatic hydrocarbons in diesel particulate matter by capillary gas chromatography and capillary gas chromatography/mass spectrometry

Summary Using a two-step liquid chromatographic separation on normalphase cartridges, crude extracts of diesel particulate matter can be separated without time-consuming sample handling into special fractions which mainly contain slightly-polar oxygenated polycyclic aromatic hydrocarbons (oxy-PAH) and nitrated polycyclic aromatic hydrocarbons (nitro-PAH). Subsequent analysis was by fused-silica capillary gas chromatography on a SE54 column along with flame-ionisation (GC/FID) and positive-ion electron-impact mass spectrometric detection (GC/MS) respectively. A number of individual oxy-PAH belonging to four different chemical classes (ketones, quinones, anhydrides and aldehydes) and several individual nitro-PAH were characterized by their retention times and mass spectra. Presented at the 15th International Symposium on Chromatography, Nürnberg, October 1984     

Determination of polycyclic aromatic hydrocarbons in vegetable oils using solid-phase microextraction-comprehensive two-dimensional gas chromatography coupled with time-of-flight mass spectrometry

A simple and fast solid-phase microextraction method coupled with comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry was developed for analysis of polycyclic aromatic hydrocarbons in edible oil, performed directly in a hexane solution of the oil. Sampling conditions (solvent used, extraction time, extraction temperature and fiber rinsing time) were optimized by using a sample of oil fortified with a standard solution of polycyclic aromatic hydrocarbons. The method was validated by calculating linear range, correlation coefficient, accuracy, repeatability, detection limit and quantification limit. The method was applied to several oils collected from the market and directly from an olive pomace extraction plant.     

Determination of polycyclic aromatic hydrocarbons, azaarenes, and thiaarenes emitted from coal-fired residential furnaces by gas chromatography/mass spectrometry

Summary Since the carcinogenic effect of emissions from hard coal briquet-fired furnaces is almost entirely caused by polycyclic aromatic compounds (PAC) with more than three rings, the composition of this fraction has been analyzed in detail.More than 170 neutral [111 polycyclic aromatic hydrocarbons (PAH), 57 thiaarenes, 6 oxaarenes] and 70 basic (azaarenes) compounds were characterized as PAC by means of GC/MS (limit of detection 0.1 mg/kg briquet). About 80 compounds were identified by comparison with reference standards. In order to obtain unequivocal evidence for the identification of 11 PAH with a molecular weight of 302, the UV- and fluorescence spectra were compared with those of the synthesized reference compounds [naphtho(1,2-k) fluoranthene, dibenz(e,k)acephenanthrylene, naphth-(2,3e) acephenanthrylene, naphtho(2,3-k)fluoranthene, dibenzo (de,qr)naphthacene, coronene, dibenzo(fg,op)naphthacene, naphtho(1,2,3,4-def)chrysene, benzo(b)perylene, dibenzo (-def,j)chrysene, benzo(rst)pentaphene]. In case of the emission condensate from hard coal briquets, PAC containing 6 and more rings cause about 50% of the carcinogenic effect in animal experiments.

---

Bestimmung von polycyclischen aromatischen Kohlenwasserstoffen, Azaarenen und Thiaarenen in der Emission von Kohle-beheizten Haushaltöfen — Bestandsaufnahme durch GC/MS

Zusammenfassung Da die krebserzeugende Wirkung von Emissionen aus Steinkohlebrikett-beheizten Zimmeröfen nahezu vollständig durch die im Kondensat enthaltenene polycyclischen aromatischen Verbindungen (PAC) mit mehr als 3 Ringen verursacht wird, wurde die Zusammensetzung dieser PAC-Fraktion untersucht.Mehr als 170 neutrale [111 polycyclische aromatische Kohlenwasserstoffe (PAH), 57 Thiaarene, 6 Oxaarene] sowie 70 basische Verbindungen (Azaarene) konnten mit der GC/MS-Kombination als PAC charakterisiert werden (Nachweisgrenze 0,1 mg/kg Brikett). Etwa 80 Verbindungen wurden durch den Vergleich mit Referenzsubstanzen identifiziert. Um in einigen zweifelhaften Fällen die Identität der isolierten mit der synthetischen Verbindung zu bestätigen, wurden bei 11 PAH mit einem Molgewicht von 302 zusätzlich auch UV- und Fluorescenzspektren verglichen [Naphtho(1,2-k)fluoranthen, Dibenz(e,k)acephenanthrylen, Naphth(2,3-e)acephenanthrylen, Naphtho(2,3-k)fluoranthen, Dibenzo(de,qr)naphthacen, Coronen, Dibenzo(fg,op)naphthacen, Naphtho(1,2,3,4-def)chrysen, Benzo(b)perylen, Dibenzo(def,j)chrysen, Benzo(rst)pentaphen]. Diese Verbindungen sind von besonderem Interesse, da PAC mit 6 und mehr Ringen im Tierversuch etwa 50% der carcinogenen Wirkung des Steinkohlenbrikett-Emissionskondensates verursachen.

     

Determination of polycyclic aromatic hydrocarbons in soy isoflavone nutraceutical products by gas chromatography coupled to triple quadrupole tandem mass spectrometry

Thirteen polycyclic aromatic hydrocarbons have been determined in soy‐based nutraceutical products. First, an optimization of extraction procedure was performed, and a solid–liquid extraction assisted by sonication and a dilute and shoot procedure were compared, selecting the dilute and shoot approach for the extraction of target compounds, utilizing a mixture of acetone/n‐hexane (1:1 v/v) as extractant solvent. After this, a clean‐up step was needed bearing in mind the complexity of these matrices. Dispersive solid‐phase extraction, using a mixture of C₁₈ and Zr‐Sep+ (25 mg/mL each) was used. The separation was achieved by gas chromatography and detection with triple quadrupole tandem mass spectrometry. For quantification purposes, matrix‐matched calibration was used. The validation was applied at three concentration levels (20, 100 and 250 μg/kg), obtaining recoveries between 70 and 120% and precision values equal to or lower than 23%. Limits of detection and quantification were below 8 and 20 μg/kg, respectively. The method was applied in 11 samples, detecting five polycyclic aromatic hydrocarbons at concentrations ranging from 4.1 to 18.5 μg/kg.     

Determination of nitrated polycyclic aromatic hydrocarbons in diesel particulate-related standard reference materials by using gas chromatography/mass spectrometry with negative ion chemical ionization

Gas chromatography/mass spectrometry (GC/MS) with negative ion chemical ionization (NICI) detection was utilized for quantitative determination of nitrated polycyclic aromatic hydrocarbons (nitro-PAHs) in diesel particulate-related standard reference materials (SRMs). Prior to GC/MS analysis, isolation of the nitro-PAHs from the complex diesel particulate extract was accomplished using solid phase extraction (SPE) and normal-phase liquid chromatographic (LC) fractionation using an amino/cyano stationary phase. Concentrations of eight to ten mononitro-PAHs and three dinitropyrenes were determined in three diesel particulate-related SRMs: SRM 1650a Diesel Particulate Matter, SRM 1975 Diesel Particulate Extract, and SRM 2975 Diesel Particulate Matter (Industrial Forklift). The results from GC/MS NICI using two different columns (5% phenyl methylpolysiloxane and 50% phenyl methylpolysiloxane) were compared to each other and to results from two other laboratories for selected nitro-PAHs. 1-Nitropyrene was the most abundant nitro-PAHs in each of the diesel particulate SRMs (19.8+/-1.1 micro g g(-1) particle in SRM 1650a and 33.1+/-0.6 micro g g(-1) particle in SRM 2975). Three dinitropyrene isomers were measured in SRM 1975 at 0.5-1.4 micro g g(-1) extract and in SRM 2975 at 1-3 micro g g(-1) particle.     

气相色谱-质谱法测定热塑性弹性体中的多环芳烃

建立了一种简单、准确的测定热塑性弹性体中16种多环芳烃(PAHs)的气相色谱-质谱(GC-MS)方法。考察了样品制备、萃取溶剂、萃取方法、时间以及温度对厂家制备的阳性热塑性弹性体样品中PAHs提取效率的影响,确定了萃取条件和方法。样品经甲苯超声萃取、浓缩后用环己烷溶解、二甲亚砜液液萃取净化后采用GC-MS进行分析,内标法定量。通过对不同材质阳性热塑性弹性体样品的加标回收、精密度试验等对建立的方法进行评价,16种PAHs的平均回收率为70%～117%,精密度为0.2%～10.8%。该方法适合于热塑性弹性体中PAHs的测定。     

固相萃取-气相色谱-质谱联用法测定水中的硝基苯类有机污染物的分析方法研究

建立了固相萃取、毛细柱气相色谱-质谱、内标标准曲线法使用选择离子(SIM)监测采集数据定量分析水中硝基苯类有机化合物的分析方法.通过对固相萃取柱的选择、固相萃取条件(样品溶液的pH、上样速率、上样体积、洗脱液选择及配比)的优化,得出了最佳实验条件.始漏体积达1.5 L.回收率大于80%.检出限为0.015～0.045 μg/L.RSD在1.1%～5.9%之间.     

Determination of 43 polycyclic aromatic hydrocarbons in air particulate matter by use of direct elution and isotope dilution gas chromatography/mass spectrometry

We are reporting a method for measuring 43 polycyclic aromatic hydrocarbons (PAH) and their methylated derivatives (Me-PAHs) in air particulate matter (PM) samples using isotope dilution gas chromatography/high-resolution mass spectrometry (GC/HRMS). In this method, PM samples were spiked with internal standards, loaded into solid phase extraction cartridges, and eluted by dichloromethane. The extracts were concentrated, spiked with a recovery standard, and analyzed by GC/HRMS at 10,000 resolution. Sixteen ¹³C-labeled PAHs and two deuterated Me-PAHs were used as internal standards to account for instrument variability and losses during sample preparation. Recovery of labeled internal standards was in the range of 86–115%. The proposed method is less time-consuming than commonly used extraction methods, such as sonication and accelerated solvent extraction (ASE), and it eliminates the need for a filtration step required after the sonication extraction method. Limits of detection ranged from 41 to 332 pg/sample for the 43 analytes. This method was used to analyze reference materials from the National Institute of Standards and Technology. The results were consistent with those from ASE and sonication extraction, and these results were also in good agreement with the certified or reference concentrations. The proposed method was then used to measure PAHs on PM_2.5 samples collected at three sites (urban, suburban, and rural) in Atlanta, GA. The results showed distinct seasonal and spatial variation and were consistent with an earlier study measuring PM_2.5 samples using an ASE method, further demonstrating the compatibility of this method and the commonly used ASE method.      

Determination of polycyclic aromatic hydrocarbons in water by solid-phase microextraction-gas chromatography-mass spectrometry

A solid-phase microextraction (SPME)-gas chromatography (GC)-mass spectrometry (MS) analytical method for the simultaneous separation and determination of 16 polycyclic aromatic hydrocarbons (PAHs) from aqueous samples has been developed, based on the sorption of target analytes on a selectively sorptive fibre and subsequent desorption of analytes directly into GC-MS. The influence of various parameters on PAH extraction efficiency by SPME was thoroughly studied. Results show that the fibre exposure time and the use of agitation during exposure are critical in enhancing SPME performance. The presence of colloidal organic matter (as simulated by humic acid) in water samples is shown to significantly reduce the extraction efficiency, suggesting that SPME primarily extracts the truly dissolved compounds. This offers the significant advantage of allowing the differentiation between freely available dissolved compounds and those associated with humic material and potentially biologically unavailable. The method showed good linearity up to 10 μg/l. The reproducibility of the measurements expressed as relative standard deviation (R.S.D.) was generally <20%. The method developed was then applied to extract PAHs from sediment porewater samples collected from the Mersey Estuary, UK. Total PAH concentrations in porewater were found to vary between 95 and 742 ng/l with two to four ring PAHs predominating. Results suggest that SPME has the potential to accurately determine the dissolved concentrations of PAHs in sediment porewater.     

气相色谱质谱法测定化妆品中9种多环芳烃

建立了气相色谱质谱法测定化妆品中9种多环芳烃的分析方法。化妆品中的萘、苯并[a]蒽、、苯并[b]荧蒽、苯并[j]荧蒽、苯并[k]荧蒽、苯并[e]芘、苯并[a]芘、二苯并[a,h]蒽等9种多环芳烃用甲醇超声提取后,用环己烷液-液萃取后浓缩,经硅胶-中性氧化铝柱净化后,采用气相色谱-质谱测定。多环芳烃浓度在0.05～2 mg/L范围内,质量浓度与其峰面积呈良好的线性关系。在低、中、高3个添加水平下,9种多环芳烃化合物的平均回收率为81.6%～100.2%,相对标准偏差为1.3%～5.8%。方法可用于化妆品中多环芳烃的检测。     

气相色谱-三重四极杆串联质谱法检测环境空气中的多环芳烃

建立了气相色谱-三重四极杆串联质谱检测环境空气中多环芳烃的方法,并利用同位素稀释法对多环芳烃进行了测定。将该方法应用于华南地区某大型石化企业周边环境空气中多环芳烃的检测,并与气相色谱-质谱方法进行了对比。结果表明,该方法的仪器检出限（0.01~0.15 μg/L）和定量限（0.03~1.5 μg/L）均优于气相色谱-质谱法（0.1~0.8 μg/L和0.3~3.5 μg/L）,并有更好的灵敏度与选择性。当利用气相色谱-质谱作为检测手段时,回收率指示物氘代菲和进样内标六甲基苯均受到了杂质的严重干扰,影响了定量结果的准确性,而三重四极杆串联质谱很好地解决了这些问题。实际样品分析时,标准曲线中16种多环芳烃相对响应因子的相对标准偏差为2.60%~15.6%,氘代化合物的回收率为55.2%~82.3%,空白加标样品的回收率为98.9%~111%,平行样品的相对标准偏差为6.50%~18.4%,采样空白含量范围为未检出~44.3 pg/m³,实验室空白含量范围为未检出~36.5 pg/m³。上述研究表明,分析环境空气中的多环芳烃时,气相色谱-三重四极杆串联质谱方法值得推广。     

Determination of polycyclic aromatic hydrocarbons in water samples by gas chromatography coupled to triple quadrupole tandem mass spectrometry using macroporous resin solid‐phase extraction

A method for the determination of 16 polycyclic aromatic hydrocarbons in water has been developed. First, we made a solid‐phase extraction column. After this, the parameters affecting the efficacy of the experimental method were optimized, including appropriate selection of a solid‐phase extraction column and cleanup conditions on columns. The separation was achieved by gas chromatography and detection with triple quadrupole tandem mass spectrometry. The method showed satisfactory linearity (R² > 0.999) over the range assayed (0.01–1 μg/mL), and limits of quantification ranging from 0.0011 to 0.0199 μg/L. The recoveries ranged from 83 to 113%. The relative standard deviation is in the range 0.86–3.1%. The results indicated that this method had high selectivity and precision that was suitable for the simultaneous determination of 16 polycyclic aromatic hydrocarbons in water.     

Isolation and analysis of polycyclic aromatic hydrocarbons from natural water using accelerated solvent extraction followed by gas chromatography-mass spectrometry

An innovative analytical procedure for the analysis of polycyclic aromatic hydrocarbons (PAHs) from large-volume water samples is presented. It involves sample preparation, sampling and the elution process in an automated continuous procedure involving the ASE technique. Prior to sampling, a XAD-2 resin column is prepared on the basis of a commercial accelerated solvent extraction (ASE) cartridge so that the resin bed is permanently fixed. Then, the XAD column inside the ASE cartridge is cleaned and conditioned. The sampling procedure involves conventional filtration with subsequent isolation of dissolved PAHs on an XAD-2 resin contained in the ASE cartridge. After sampling, the XAD-2 resin content inside the cartridge is eluted by ASE without any further sample preparation and subsequently reused. In order to validate the procedure, the PAHs were isolated from water samples from the Lake Maggiore (North of Italy) using both XAD-2 resin adsorption and hexane liquid-liquid extraction according to the International Standard Methodology ISO 17993. The mean percentages of deviation between concentrations obtained by both methodologies range from 6% for benzo(a)pyrene to 15% for fluoranthene and benzo(b,k)fluoranthene. Compared to the traditional techniques, this procedure offers numerous practical advantages: easy to perform, fast, savings in solvent volume and in time, all steps are fully automated thus avoiding any XAD-2 resin manipulation during and between steps and moreover, low detection limits were provided (0.001 ng l⁻¹ for chrysene, benzo(b,k)fluoranthene, benzo(a)pyrene, dibenz(a,h)anthracene, benzo(g,h,i)perylene and indeno(1,2,3-cd)pyrene, and 0.01 ng l⁻¹ for acenaphthylene and fluoranthene).This procedure was developed in the frame of a project aimed at evaluating the diffuse input of organic contaminants in the Lake Maggiore.     

Solid-phase microextraction combined with gas chromatography/triple quadrupole tandem mass spectrometry for determination of nitrated polycyclic aromatic hydrocarbons in sediments

Nitro-polycyclic aromatic hydrocarbons have been detected in various environmental media. However, determination in sediment matrix is challenging due to the lack of a suitable method. In this study, a reliable method for determining 15 nitro-polycyclic aromatic hydrocarbons in sediments was developed based on accelerated solvent extraction and solid-phase microextraction coupled with gas chromatography–tandem mass spectrometry. The accelerated solvent extraction and solid-phase microextraction are sample pre-treatment techniques that have advantages, such as rapid operation and minimal sample volume. Initially, the solid-phase microextraction was optimized using five commercial fibers and from that 65 μm polydimethylsiloxane/divinylbenzene fiber was selected as the best fiber. Further, the accelerated solvent extraction conditions were optimized by Taguchi experimental design, such as extraction temperature (120℃), extraction solvent (dichloromethane), number of cycles (two), static extraction period (4 min), and rinse volume (90%). The method parameters, such as limits of quantitation, and intraday and interday accuracy and precision, were in the range of 0.067–1.57 ng/g, 75.2–115.2%, 69.9–115.4%, and 1.0–16.5%, respectively. Upon meeting all the quality criteria, the method was applied successfully to analyze real sediment samples. Therefore, our study creates a new prospect for the future application of direct immersion solid-phase microextraction in sediment analysis.     

Study of fungal degradation products of polycyclic aromatic hydrocarbons using gas chromatography with ion trap mass spectrometry detection

Representatives of polycyclic aromatic hydrocarbons (PAHs) were degraded by ligninolytic fungus Irpex lacteus. The products were analyzed by GC-Ion trap mass spectrometry. The combination of full scan mass spectra, product ion scans (MS-MS) and derivatization of the degradation products of anthracene, phenanthrene, fluoranthene and pyrene provided further insight in the degradation mechanism initiated by I. lacteus. Particularly, the product ion scans enabled the interpretation of unknown degradation products, even though they were only produced at trace level. Most of the structures suggested were later confirmed with authentic standards.