Active synchronization of two mode-locked lasers with optical cross correlation

Two mode-locked Ti:sapphire lasers of different wavelengths were precisely synchronized by a simple feedback system employing sum-frequency generation (cross correlation). When the timing error exceeded the pulse duration, the periodic bunch of the sum-frequency pulse was used for rough timing adjustment. Using cross correlation with a stretched pulse, we struck a balance between wide locking range and sensitive timing detection. When the two lasers were well-synchronized, we obtained a continuous cross-correlation pulse train for 3 min. The holding time of the laser synchronization was extended to over one hour by adding a motorized stage to the PZT-mounted cavity mirror. We estimated the rms timing jitter between the two lasers by a scanning cross-correlation measurement. We confirmed that the rms timing jitter of the two lasers during 1.8 s was 28 fs. Received: 30 January 2002 / Revised version: 14 June 2002 / Published online: 8 August 2002     

Wavelength-independent all-optical synchronization of a Q-switched 100-ps microchip laser to a femtosecond laser reference source

We present a Q-switched microchip laser emitting 1064-nm pulses as short as 100 ps synchronized to a cavity dumped femtosecond laser emitting 800-nm pulses as short as 80 fs. The synchronization is achieved by presaturating the saturable absorber of the microchip laser with femtosecond pulses even though both lasers emit at widely separated wavelengths. The mean timing jitter is 40 ps and thus considerably shorter than the pulse duration of the microchip laser.     

Comparison between c-cut and a-cut Nd:YVO4 lasers passively Q-switched with a Cr4+:YAG saturable absorber

Comparison between c-cut and a-cut Nd:YVO₄ microchip lasers passively Q-switched with a Cr⁴⁺:YAG saturable absorber is experimentally made. The lower emission cross section of the c-cut Nd:YVO₄ crystal can enhance the passive Q-switching effect to produce a peak power 10 times higher than that obtained with the a-cut crystal. The experimental result further reveals that a c-cut Nd:YVO₄ crystal is a very convenient material for short-pulse (sub-nanosecond) and high-peak-power (>10 kW) lasers. Received:10December2001/Revisedversion:22January2002 / Published online: 14 March 2002     

Q-switched Nd lasers pumped directly into the F3/2 emitting level

The influence of the direct pumping into the ⁴F_3/2 emitting level on the output characteristics of continuous-wave (CW) pumped, passively or actively (acoustooptic, AO) Q-switched Nd lasers is discussed. In case of passive Q-switching by Cr⁴⁺:YAG saturable absorber (SA) crystal, the change of pumping wavelength from 0.81 μm into the highly-absorbing ⁴F_5/2 level to 0.88 μm into the ⁴F_3/2 level of Nd does not modify the energy of the Q-switch pulse, but increases the pulse repetition rate and the laser average power for the same absorbed pump power. This is demonstrated with 0.81 and 0.88 μm CW laser diode-pumped Nd:YAG and Nd-vanadate lasers with average output power in the watt-level range at 1.06 μm. The effect is explained by the control of passive Q-switching by the intracavity photon flux that is influenced by the pump wavelength and by the initial transmission of the SA crystal. On the other hand, it is discussed and experimentally proved that due to the possibility to control externally the frequency of switching, in case of the AO Q-switched Nd laser the change of the pump wavelength from 0.81 to 0.88 μm increases the pulse energy for a fixed frequency, leading to a corresponding increase of the average laser power.     

Repetitive passive Q-switching and bistability in lasers with saturable absorbers

We report detailed experimental data on the passive Q-switching operation in a CO₂ laser with CH₃I saturable absorber, and on the transient behaviour in the near-Q-switching situation. Under suitable operating conditions, we found bistability in the output power. In some cases, we observed the simultaneous presence of bistability and passive Q-switching. The theoretical part of the paper starts from the four-level model of laser with saturable absorber, as formulated by other authors. By adiabatically eliminating the variables of the resonant levels, we reduce the problem to a set of three differential equations, from which we derive explicit analytical conditions for the rise of passive Q-switching. These conditions turn out to be in good qualitative and partially quantitative agreement with our experimental findings as well as with other experimental data previously obtained by other authors. Finally we classify the possible combinations of passive Q-switching and bistability that one can find in this type of experiments.     

Passive Q-switching of short-length Tm-doped silica fiber lasers by polycrystalline Cr:ZnSe microchips

We demonstrate passive Q-switching of short-length double-clad Tm³⁺-doped silica fiber lasers near 2 μm pumped by a laser diode array (LDA) at 790 nm. Polycrystalline Cr²⁺:ZnSe microchips with thickness from 0.3 to 1 mm are adopted as the Q-switching elements. Pulse duration of 120 ns, pulse energy over 14 μJ and repetition rate of 53 kHz are obtained from a 5-cm long fiber laser. As high as 530 kHz repetition rate is achieved from a 50-cm long fiber laser at ∼10-W pump power. The performance of the Q-switched fiber lasers as a function of fiber length is also analyzed.     

半导体可饱和吸收镜作为被动调Q吸收体的发展状况

简介了近年来发展起来的若干种新型固体激光器被动调Q用吸收体：掺Cr4+系列，Cr，Nd∶YAG自调Q激光晶体，人眼安全激光器被动调Q用吸收体，GaAs吸收体，半导体可饱和吸收镜。着重介绍了固体激光器和光纤激光器调Q用半导体可饱和吸收镜的原理、研制方法及应用状况。     

Lasers operating on cascade transitions of triatomic molecules

The general conditions necessary for the operation of gas lasers based on cascade vibrational-rotational transitions of molecules in the pulse-periodic regime are formulated. The features of such triatomic-molecule lasers with arbitrary excitation are discussed. A computation model is proposed for determining the energy characteristics (maximum attainable efficiency, average and relative lasing power, specific energy output) of free-flow cascade lasers. Systems are analyzed with various excitation methods: gasdynamic (including those with optical feedback), electric-discharge, and chemical (with the DF-CO₂ laser as the example). Practical recommendations with respect to the choice of mixture composition, optimum cavity lengths along the gas stream, and Q-switching frequency are made for the cascade lasers. A molecular gasdynamic laser emitting three wavelengths simultaneously is proposed.Quantum Radiophysics and Optics Division, Lebedev Physics Institute. Translated from Preprint No. 177 of the Lebedev Physics Institute, Academy of Sciences of the USSR, Moscow, 1989     

Synchronization of Chaotic Intensities and Phases in an Array of N Lasers

A linear array of N mutually coupled single-mode lasers is investigated. It is shown that the intensities of N lasers are chaotically synchronized when the coupling between lasers is relatively strong. The chaotic synchronization of intensities depends on the location of the lasers in the array. The chaotic synchronization appears between two outmost lasers, the second two outmost lasers, etc. There is no synchronization between nearest neighbors of the lasers. If the number of N is odd, the middle laser is never synchronized between any lasers. The chaotic synchronization of phases between nearest lasers in the array is examined by using the analytic signal and the Gaussian filter methods based on the peak of the power spectrum of the intensity. It can be seen that the message of chaotic intensity synchronization is conveyed through the phase synchronization.     

Dual-lag synchronization between coupled chaotic lasers due to path-delay interference

We study experimentally the synchronization dynamics of two semiconductor lasers coupled unidirectionally via two different delayed paths. The emitter laser operates in a chaotic regime characterized by low-frequency fluctuations due to optical feedback and induces a synchronized dynamical activity in the receiver laser, which operates in the continuous-wave regime when uncoupled. Different delays in the two coupling paths lead to the coexistence of two time lags in the synchronized dynamics of the oscillators. This dual-lag synchronization degrades the average synchronization quality of the system of coupled lasers and hinders the transmission of information between them. Numerical simulation results agree with the experimental observations, and allow us to explore this phenomenon in a wide parameter range, and quantify the degree of signal transmission degradation caused by this chaotic path-delay interference.     

Diode-pumped Nd:YVO<Subscript>4</Subscript> and Nd:KGd(WO<Subscript>4</Subscript>)<Subscript>2</Subscript> 1.3 μm lasers passively Q-switched with PbS-doped glass

Diode-pumped Nd:YVO₄ and Nd:KGW lasers passively Q-switched with PbS-quantum dot-doped phosphate glass were demonstrated. For the Nd:YVO₄ laser, pulses 110 ns in duration with a 13% Q-switching efficiency were obtained. The absorption recovery time of the PbS-doped glass was measured to be 27±4 ps. Some recommendations for more efficient use of PbS-doped glasses for Q-switching of diode-pumped lasers are suggested on the basis of our analysis. Received: 29 July 2002 / Revised version: 18 September 2002 / Published online: 12 February 2003 RID="*" ID="*"Corresponding author. Fax: +375-17/232-6286, E-mail: savitski@eudoramail.com     

CW and passive Q-switching of 1331-nm Nd:GGG laser with Co<Superscript>2+</Superscript>:LMA saturable absorber

In this paper, the output performances at 1331 nm in continuous-wave (CW) operation and the passive Q-switching regime of a Nd:Gd₃Ga₅O₁₂(Nd:GGG) laser crystal have been investigated under pumping with diode lasers. A maximum CW output power of 1.5 W was reached at an incident pump power of 7.5 W; the overall optical-to-optical efficiency and the slope efficiency with respect to the pump power were 21.5% and 19.4%, respectively. The passive Q-switching regime was achieved with Co²⁺:LaMgAl₁₁O₁₉ (Co²⁺:LMA) saturable absorber (SA) crystals. A maximum average output power of 183 mW was recorded with a Co²⁺:LMA SA with initial transmission T _i of 90%. The pulse energy was 18.7 μJ and the pulse duration was 26.1 ns, which correspond to a pulse peak power of 0.7 kW. With a Co²⁺:LMA SA with T _i=81%, the average power decreased to 131 mW. However, the pulse energy increased to 21.4 μJ, the pulse duration was 16.4 ns and the pulse peak power increased to 1.3 kW.     

Temporal synchronization of independently tunable single longitudinal mode hybrid CO2 lasers

We report a quantitative study of temporal synchronization of two independently tunable, single longitudinal mode, hybrid CO₂ lasers, sharing a common high pressure section. The theoretical estimates for the dependence of the laser pulse build up time on the cw section pressure are in satisfactory agreement with the experimental results. Further, we show that temporal synchronization over a larger frequency range with no significant degradation of peak power or longitudinal mode selection is possible, by utilising the cw section gain length and cavity Q as additional control parameters.     

Mode-locked diode-pumped vanadate lasers operated with PbS quantum dots

The use of glasses doped with PbS nanocrystals as intracavity saturable absorbers for passive Q-switching and mode locking of c-cut Nd:Gd_0.7Y_0.3VO₄, Nd:YVO₄, and Nd:GdVO₄ lasers is investigated. Q-switching yields pulses as short as 35 ns with an average output power of 435 mW at a repetition rate of 6–12 kHz at a pump power of 5–6 W. Mode locking through a combination of PbS nanocrystals and a Kerr lens results in 1.4 ps long pulses with an average output power of 255 mW at a repetition rate of 100 MHz.     

Solid-state laser passively Q-switched in a new geometry

A new passive Q-switching geometry of a laser cavity has been proposed. In the proposed scheme, the volume of the passive Q-switch just partially overlaps the intracavity laser beam cross-section, leading, however, to the entire beam modulation. This technique was applied for passive Q-switching of a flash-lamp pumped multimode YAG:Nd³⁺ laser by LiF:F₂⁻ crystals. The giant pulse laser action threshold has been detected in the proposed geometry, and is lower than that in the scheme where the passive Q-switch operates in the traditional manner. Stable giant pulse oscillation of 1064 nm wavelength with a pulse duration of 24 ns, pulse energy of 450 mJ, and pulse repetition rates of up to 100 Hz, have been obtained.     

Passive Q-switching at 1.54 μm of an Er–Yb: GdCa4O(BO3)3 laser with a Co2+: MgAl2O4 saturable absorber

We report, for the first time to our knowledge, efficient passive Q-switching of the 1.54-μm laser transition in an Er–Yb-doped crystalline medium. The laser configuration is a compact microchip design that is suitable for a range of practical applications such as range finding and lidar. The slope efficiency of 11.6%, pulse duration of 5–6 ns and average output power of 88 mW are all comparable with standard Er–Yb:glass lasers.     

Tri-wavelength laser with Nd:CLTGG crystal

Continuous-wave (CW) and passively Q-switched operations of laser diode-end-pumped Nd:CLTGG laser at 1.06 μm was demonstrated for the first time. The laser spectrum was found to be tri-wavelength, with respective wavelengths of 1058.4, 1060.5, and 1065.5 nm for both CW and passive Q-switching regime. The highest CW output power of 2.6 W was obtained with an optical-optical conversion efficiency of 13.9% and a slope efficiency of 17.1%. In the passive Q-switching regime, the highest output power, shortest pulse width, largest pulse energy and highest peak power were achieved as 242 mW, 45.8 ns, 1.65 μJ and 0.4 kW, respectively. The passively Q-switched tri-wavelength laser should have the potential to be used for terahertz radiation generation.     

Diode-laser pumped 1.328 μm Nd:Sr5(PO4)3F miniature laser

Nd:Sr₅(PO₄)₃F, known as Nd:S-FAP, is a new material for efficient and miniature diode-laser pumped solid-state lasers. By using a laser-diode pump operating at 805.4 nm, Nd:S-FAP has been successfully lased at 1.328 μm. A slope efficiency of 33.5% and a laser threshold of 18.5 mW have been measured. The theoretical formulas for threshold power and slope efficiency were given and the theoretical estimation agreed with the experimental result.     

Passive Q-switches for Nd:hosted Solid State Lasers

The currently available Nd:hosted lasers utilizing passive Q-switches: a plastic dye sheet, a LiF:F₂- color center crystal, a Cr⁴⁺:YAG crystal or a RG1000 colored glass filter have been investigated in detail and the results summarized for comparison purposes for the first time. We first briefly summarize our own and others’ past studies, and report on recent new results concerning the use of Cr⁴⁺:YAG crystals and RG1000 colored glass filters as Nd:hosted laser passive Q-switchings. We then investigate in detail solid state laser system design using the above four passive modulators. Typical interpretations are given based on characteristic features of the materials, such as their saturation intensity and relaxation times. The results are then explained via adequate equations derived with respect to the relevant physical parameters of the materials. The optical dersity selection of plastic dye sheet passive Q-switching for the Nd:YAG laser system design is verified quantitatively, and the slope efficiencies from plastic dye sheet passive Q-switched operation by single pulse and multiple pulse bursts are investigated. The multi-peak Q-switched pulse timing phenomena are presented as well. The outstanding annealability, long lifetime, inexpensiveness and high repetition rate operation of LiF:F₂- crystals are highly recommended.     

Generation of two-color femtosecond pulses by self-synchronizing Ti:sapphire and Cr:forsterite lasers

We report a novel technique for the synchronization of two different femtosecond solid-state lasers by crossing of both laser pulses in a Kerr medium. Stable dual-wavelength femtosecond pulses at central wavelengths of 820 and 1250 nm have been obtained. The tolerance of cavity-length mismatch is ~0.6mum , where the pulse widths of the Ti:sapphire and the Cr:forsterite lasers are 18 and 40 fs, respectively, at average powers of 600 and 110 mW. The typical timing jitter derived from the cross correlation is less than 3 fs.