基于模式转换及双峰谐振效应的薄包层镀膜长周期光纤光栅特性研究

基于耦合模理论,首先研究了镀膜长周期光纤光栅(LPFG)高阶包层模的模式转换,划分了高阶包层模的非模式转换区及模式转换区。分析了高阶包层模有效折射率随薄膜厚度增加的响应特性,包层模谐振波长在模式转换区的偏移量要大于非模式转换区。在此基础上,研究了不同包层半径下高阶包层模谐振波长随光栅周期的变化情况,结果表明,相同包层半径下模式转换区内双峰间距的偏移量大于非模式转换区;无论在模式转换区还是非模式转换区,包层半径的减小将增加双峰间距的偏移量。最后分析了不同包层半径下的高阶包层模双峰透射谱在模式转换区及非模式转换区内的折射率响应,进而提出了薄包层镀膜LPFG的优化设计方案,当选定敏感膜层厚度及折射率处于镀膜LPFG的模式转换区内,光栅周期靠近相位匹配转折点时,将得到灵敏度高于传统LPFG双峰传感器的镀膜LPFG折射率型双峰传感器;而减小包层半径,将进一步提高传感器的分辨本领。     

Enhancement of sensitivity in long-period fiber gratings with deposition of low-refractive-index materials

It was proved [Opt. Lett. 30, 720 (2005)] that the deposition of an overlay of higher refractive index than that of the cladding on a long-period fiber grating (LPFG) causes large shifts in the attenuation bands induced by the grating. The result is an enhancement of the sensitivity of the LPFG to variations in the ambient and overlay refractive indices or the overlay thickness. The limitation of the previous design to materials with higher refractive indices than that of the cladding of the LPFG is overcome with a five-layer model. To this purpose, a first overlay of higher refractive index than that of the cladding of the LPFG will enhance the sensitivity of the device to variations in the refractive index of a second overlay of lower refractive index than that of the cladding of the LPFG. Moreover, it is proved that, if the second overlay is thick enough, its behavior resembles that of an infinite layer.     

Deposition of coatings on long-period fiber gratings: tunnel effect analogy

The sensitivity of Long-period fiber gratings (LPFGs), coated with high-refractive-index thin film overlays, to the refractive index and the thickness of the overlay, and to the ambient refractive index, can be enhanced with a design based on a two-overlay coating of an LPFG. The first overlay of lower refractive index than the cladding affects the guidance of a cladding mode in the second overlay of higher refractive index than the cladding. This causes a more abrupt cladding modal redistribution than with the deposition of a unique high-refractive-index overlay. The phenomenon is analyzed with a method based on a vectorial analysis of modes and the application of coupled mode theory.     

一种双段多层长周期光纤光栅光谱特性研究

长周期光纤光栅(LPFG)传感器具有非常广泛的应用价值,而有效解决物理量交叉敏感问题是其实用化的关键。基于LPFG对包层外介质折射率和厚度的敏感性,提出一种双段多层折射率横向分布结构的新型LPFG传感器的设计,并利用耦合模理论和传输矩阵方法分析了镀膜材料折射率、膜层厚度和镀层长度对新型LPFG传感器光谱特性的影响。软件仿真结果证明,这种LPFG由于结构设计上的特殊性,将使LPFG的谐振峰发生分裂,即一个透射峰分裂为两个。由于两个分裂峰对应力和温度的灵敏度不同,利用该结构的LPFG作为传感器,可以实现温度、应力等物理量的同步测量,从而解决LPFG传感器的交叉敏感问题。     

Structure design of refractive index sensor based on LPFG with double-layer coatings

Based on the coupled-mode theory, the mode transition and transmittance of LP modes in an LPFG with double-layer coatings are studied theoretically. As a refractive index sensor, this LPFG structure is designed for high sensitivity by selecting a suitable thickness and refractive index of the double-layer coatings. Date simulation indicates that the effective index of the LP cladding mode increases in steps with the first coating thickness, thus LP mode is guided to the overlay and the mode transition takes place, where the LP modes can be easily affected by the ambient. Thereby, the coated LPFG sensor should be designed to operate at the transition region. In addition, the effective refractive index of LP cladding modes also increases in steps with the refractive index of the second overlay. For the higher order LP modes, the transition regions are broaden and the dynamic responses are greater than the lower LP modes, which means the higher order LP modes can be used for lower index overlay sensing. Further, the transmittance spectrum, sensitivity and measurable dynamic range of this LPFG are analyzed. The sensitivity of the LPFG sensor is available to $10^{3}$ with suitable overlay thickness and measurable dynamic range of the sensitive film refractive index is available to $10^{-2}$ . So the presented LPFG sensor enhances the design flexibility and enlarges the scope of application, which will likely be developed for high sensitivity LPFG sensors.     

Design of a coated thinly clad chalcogenide long-period fiber grating refractive index sensor based on dual-peak resonance near the phase matching turning point

A novel method for designing chalcogenide long-period fiber grating (LPFG) sensors based on the dual-peak resonance effect of the LPFG near the phase matching turning point (PMTP) is presented. Refractive index sensing in a high-refractive-index chalcogenide fiber is achieved with a coated thinly clad film. The dual-peak resonant characteristics near the PMTP and the refractive index sensing properties of the LPFG are analyzed first by the phase-matching condition of the LPFG. The effects of film parameters and cladding radius on the sensitivity of refractive index sensing are further discussed. The sensor is optimized by selecting the appropriate film parameters and cladding radius. Simulation results show that the ambient refractive index sensitivity of a dual-peak coated thinly clad chalcogenide LPFG at the PMTP can be 2400 nm/RIU, which is significantly higher than that of non-optimized gratings. It has great application potential in the field of chemical sensing and biosensors.     

啁啾长周期光纤光栅的超宽带滤波特性及其切趾优化

基于光纤光栅的模式耦合理论,采用传输矩阵法对啁啾长周期光纤光栅(LPFG)的超宽带滤波特性进行了分析。研究表明当啁啾LPFG的纤芯模同时与同向传输的多个阶次的包层模发生耦合,且与多个不同阶次包层模对应的谐振峰交叠时,其传输谱带宽可扩展到500nm以上,可用做超宽带带阻滤波器。传输谱带宽随模式序数、啁啾系数、光栅长度、周期和折射率调制量的增加单调递增,但随光纤包层半径的增大单调递减。采用高斯折射率切趾技术抑制了传输谱旁瓣,为设计超宽带滤波器提供了新的方法。     

镀有SiO_2-WO_3薄膜LPFG折射率传感特性研究

采用四层阶跃折射率几何模型,研究了镀有SiO2-WO3薄膜LPFG在溶液折射率测量方面的特性,并与未镀膜情况进行了比较。当LPFG包层外镀膜后,测量纯水、CaCl2溶液(浓度为450gL-1,折射率为1.4056)时波长漂移量分别是未镀膜时的1.67和2.55倍;谐振峰的损耗变化分别是未镀膜时的4.44和2.82倍;在1.36-1.38折射率范围内,传感器的灵敏度和分辨率分别是216.58nm和0.82×10-5,是镀膜前的3.27和0.30倍,说明镀膜后LPFG对溶液折射率测量的灵敏度和分辨率得到了很大的提高。     

镀高折射率纳米膜的长周期光纤光栅特性研究

针对镀高折射率纳米膜的长周期光栅,建立了传感理论模型,研究了长周期光栅的谐振波长与纳米膜厚度及外界折射率的关系,给出不同纳米膜厚度下长周期光栅不同包层模式重组特性.研究发现,当长周期光栅外面镀上一层沿角向均匀分布的纳米膜时,随着膜厚变化会出现包层模分布的明显调制;适当选择镀膜参数和外界介质折射率,最低次包层模式HE1,2会成为镀膜层中的导模,其他的包层模式将会发生模式转换现象;对于较低次包层模式(如HE1.6),在模式转换的时候存在两步转换,而高次的包层模只有一步转换(如HE1.14).同时给出了包层模式转换对外界折射率响应的关系:当膜层厚度增加时,长周期光栅模式转换现象移至低折射率区域.     

CO2激光脉冲边缘写入的长周期光栅折射率特性研究

报道了一种用高频CO2激光脉冲在普通通信光纤包层边缘单侧写入的新型长周期光纤光栅。研究发现,这种长周期光纤光栅的折射率变化主要发生在光纤包层区域,而纤芯的折射率变化较小;同时该光栅的附加损耗低于0.5 dB。进一步折射率特性实验研究表明,由于其特殊的折变结构,这种光栅具有较高的外界环境灵敏度,当外界折射率在1.41~1.45范围内变化时,其谐振波长漂移量高达15.52 nm,比实验测得的用传统方法写入的长周期光纤光栅谐振波长漂移量高出近3倍,这种光栅结构在光纤传感中将具有重要的应用。     

长周期光纤光栅折射率特性仿真的新方法

基于长周期光纤光栅的模式耦合机理,提出一种快速模拟长周期光纤光栅折射率特性的方法。该方法在计算包层模式的有效折射率时分开计算,在环境折射率小于包层折射率时采用二分法和分步搜索法结合计算包层模式的有效折射率,在环境折射率大于包层折射率时采用Nelder-Mead加分步搜索法求解包层模式的有效折射率。在应用谐振波长的决定式求解与环境折射率的匹配的谐振波长时,采用变区间应用二分法求解而不是传统的逐步搜索法求解谐振波长。数值结果与实验结果做了对比,两者基本一致。实践证明,该方法方便快捷,比一般的方法速度提高7倍以上。     

Optimal design of temperature-insensitive long period fiber gratings for athermal refractive-index sensor

Based on coupled-mode theory of long-period fiber grating (LPFG), a theoretical analysis and simulations for the optimal design of a temperature-insensitive LPFG is presented in order to achieve an athermal condition for sensing the refractive index of the external medium. Effects of the variation of the cladding radius and grating period on the temperature sensitivity of the LPFG are discussed. Both of these parameters are found to be important to control the temperature sensitivity when the thermo-optic coefficients of core and cladding materials are of the same order. Other grating parameters are also optimized in order to achieve a good contrast of the grating period with resonance wavelength in the 1.5 μm region and to sense the external medium refractive index over a wide range. Variation of external medium refractive index from 1.0 to 1.45 results a red-shift in the LPFG resonance wavelength by 86 nm with its temperature sensitivity as low as 0.008 nm/°C over a temperature range of 0–80 °C for this optimally designed LPFG.     

基于长周期光纤光栅的磁场传感方案的实现

长周期光纤光栅是近几年出现的一种新型光纤器件。其耦合机理是前向传输的纤芯基模与前向传输的各阶包层模式之间的耦合 ,这与光纤布喇格光栅明显不同。它对温度、应力、弯曲及外部折射率的变化具有相当高的灵敏度 ,是一种理想的光纤型敏感结构。提出利用长周期光纤光栅谐振波长的移动或移动变化量进行磁场强度的测量 ,并进行了理论推导、仿真实验及分析研究。得出了谐振波长变化量与外界磁场强度的关系模型。分析了设计中应该考虑的因素。     

Spectral characteristics of a two-section multilayer long-period fiber grating sensor

A novel long period fiber grating (LPFG) sensor structure is proposed in this paper. It is constituted by coating an over-layer partially on the fiber grating. Then the LPFG has a two-section multilayer transversely distributed refractive index structure. Using coupling mode theory and transfer matrix method, the influences of refractive index, thickness and length of the coating layer on the spectral characteristics of the new type LPFG were analyzed. The simulation results show that the resonant band is split due to the particularity of the LPFG structure, and the wavelength splitting is strongly dependent on the parameters of the coating layer. This LPFG designing may solve the cross sensitive problem and then realize synchronous measurement of temperature, strain and other physical quantities.     

基于双峰谐振效应的镀金属长周期光纤光栅液体浓度传感器

利用长周期光纤光栅(LPFG)中的双峰谐振效应,结合表面等离子体共振(SPR)传感器的高灵敏度,提出了一种新型镀金属光纤光栅液体浓度传感器.采用双包层结构模型和耦合模理论,分析r镀金属长周期光纤光栅双峰效应的谐振特性,环境折射率的传感特性以及金属膜厚对双峰LPFG灵敏度的影响.实验上制作了具有双峰效应的镀银膜长周期光纤...     

镀膜相移长周期光纤光栅大间隔双峰滤波特性

研究了镀膜相移长周期光纤光栅(PS-LPFG)工作于相位匹配转折点(PMTP)时的大间隔双峰滤波特性。LPFG工作于PMTP时,纤芯模与高次包层模耦合产生的损耗峰3dB带宽可达288nm以上,在此LPFG中点引入单个π相移时在中心波长两侧出现的两个阻带峰间隔达388nm,远大于低次包层模耦合π相移LPFG的双峰间隔。在LPFG中均匀地引入M(M>1)个π相移时,双峰间隔随M的增大而增大,M为奇数时,中心波长损耗为0;M为偶数时,中心波长损耗随M的增大而减小。薄膜折射率与厚度的增加都将使两个阻带峰向短波长方向移动并增大双峰间隔。光栅长度的增大在改变双峰峰值损耗的同时使双峰间隔逐渐减小。     

Control of resonant peak depths of tunable long-period fiber gratings using overcoupling

We present a method to reduce changes in the resonant peak depth of a long-period fiber grating (LPFG) as the resonant band is tuned by varying the external refractive index. We theoretically analyze the effects of the initial coupling strength on the peak depth change as external refractive index is varied. By controlling the initial coupling strength, it is experimentally demonstrated that an optimum peak depth can be obtained over a range of operating wavelengths that will maximize the sensitivity and stability of LPFG based sensors and tunable filters.     

矩形折射率调制型薄膜长周期光纤光栅特性研究

镀膜长周期光纤光栅传感器是目前光纤光栅传感研究的一个热点,但关于此类传感器模型的全面的理论分析目前还很少。本文基于严格的四层模型,从理论上对芯层折射率调制为矩形波调制的薄膜长周期光纤光栅的特性进行了详细的分析。在充分考虑材料色散对光纤芯层和包层的影响后,对薄膜参数、占空比和环境折射率的变化对镀膜长周期光纤光栅的谱特性的影响进行了数值研究。研究结果表明,薄膜参数对透射谱有重要影响,合理设计薄膜厚度可以获得较佳的损耗峰。研究还发现,镀膜后占空比对透射谱的影响减小,而对环境折射率变化的敏感度增加。在占空比为0.5时光栅具有最大的损耗峰值。     

模式耦合理论在圆周对称长周期光纤光栅建模中的应用

长周期光纤光栅是不同于光纤Bragg光栅的一种光纤光栅器件 ,根据模式耦合理论 ,长周期光纤光栅表现为前向传播的纤芯导模和同向的各阶次包层模式之间的耦合。分析研究了长周期光纤光栅轴向的模场变化。忽略轴向的模式耦合以及包层模式之间的相互耦合作用 ,并认为折射率指数的调制只存在于纤芯中 ,建立了简化的长周期光纤光栅数学模型。对圆周对称轴向均匀型长周期光纤光栅谱特性进行了仿真 ,其结果与实验结果基本吻合 ,表明了简化的数学模型的合理性     

基于包层模的光纤布拉格光栅折射率传感特性

提出了基于光纤布拉格光栅(FBG)包层模式的折射率传感方案。实验中,利用不同浓度的丙三醇水溶液作为外界折射率传感溶液,采用氢氟酸溶液化学腐蚀的方法来减小光纤包层的直径以增大包层模式对外界折射率的敏感度,研究了腐蚀后光纤布拉格光栅包层模式的耦合波长对外部折射率的变化关系。实验结果表明在1.3300~1.4584的折射率范围内,包层模式耦合波长随外界折射率增大而增大,在接近光纤包层折射率处具有很高的折射率灵敏度,最大达到了172 nm/riu(refractive index unit)。而且,包层模谐振的光谱半峰全宽(约0.07 nm)仅为布拉格纤芯模谐振光谱半峰全宽的1/4,能够获得更好的传感精度。