Single-wavelength-pump bi-directional hybrid fiber amplifier for bi-directional local area network application

This paper proposes a novel bi-directional hybrid fiber amplifier using a single-wavelength pump laser diode (LD) at 1495 nm. The hybrid amplifier is theoretically applied in a 50 km bi-directional local area network (LAN) with 26 ch × 10 Gb/s for bi-directional transmission. Thirteen C-band channels serve as downlink signals while the other 13 L-band channels are employed as uplink signals. Without loss of generality, four channels (two from each band) are experimentally analyzed. Erbium doped fiber (EDF) provides amplification for the C-band channels and Raman amplification amplifies the L-band channels. The pump efficiency is improved by employing a double-pass scheme for both the Erbium doped fiber amplifier (EDFA) and Raman fiber amplifier (RFA). The chromatic dispersion incurred by all the channels is precisely compensated for by inserting a fiber Bragg grating (FBG) array in appropriate locations along the dispersion compensating fiber (DCF) segments. Moreover, gain equalization of all the channels is achieved by adjusting the FBG reflectivity. Both the simulation results and experimental measurements confirm the proposed device feasibility and potential application in a bi-directional LAN.     

Gain and gain-flatness improved photonic crystal fiber Raman amplifier based on a dual-pass amplification configuration with single pump laser

A gain and gain-flatness improved L-band dual-pass Raman fiber amplifier (RFA) utilizing a photonic crystal fiber (PCF) as gain medium is demonstrated. By introducing complementary gain spectra of typical forward and backward pumping single-pass RFA using the same PCF, we finally achieve average net gain level of 22.5 dB with a ±0.8 dB flattening gain in 20-nm bandwidth from 1595 nm to 1615 nm, which is rare in RFAs with only one single pump and no flattening filter. Compared with the single-pass pump configurations, gain level, flatness and bandwidth are greatly improved by using the dual-pass amplification configuration. The limitation of this configuration caused by multi-path interference (MPI) noise and stimulated Brillouin scattering (SBS) is also discussed.     

Utilization of stimulated Raman Scattering as secondary pump on hybrid remotely-pump l-band Raman/erbium-doped fiber amplifier

An L-band remotely-pumped erbium-doped fiber amplifier incorporating a secondary pumping scheme utilizing stimulated Raman Scattering (SRS) was demonstrated. 1423 nm Raman laser was employed to generate SRS which became the secondary pump source. The amplifier displayed excellent gain of up to 27.3 dB at 1570 nm for −30 dBm input. Noise figures were also kept to a minimum, with the highest figure measured at 11 dB which was influenced by imperfection of the C/L coupler utilized in this architecture. Overall transmission performance was measured as well and demonstrated an encouraging outcome with gain as high as 24 dB while the noise figure was maintained at about 11 dB. The L-band signal amplification was also contributed by the stimulated Raman scattering along the transmission fiber. The outcome of this study emphasized the feasibility of secondary pumping scheme using SRS in L-band gain enhancement.     

Simulation and experimental characterization of Raman/EDFA hybrid amplifier with enhanced performance

We present simulation and experimental characterization of a hybrid amplifier comprising of a Raman amplifier and an erbium doped fiber (EDF) amplifier, with enhanced performance. The incorporation of a pumped EDF section in a fiber Raman amplifier (FRA) employing a dispersion compensating fiber is demonstrated to provide superior performance than a sole FRA system. The hybrid amplifier is characterized in terms of single channel gain and noise figure, and the results of measurements are shown to be in close agreement with the simulated results. Polarization-dependent gain (PDG) and multi-channel measured and simulated gain characterization of the Raman/EDFA hybrid amplifier are also presented.     

A dual pumped double-pass L-band EDFA with high gain and low noise

This paper presents an efficient pumping scheme for L-band erbium-doped fiber (EDFA) amplifier to reach high gain and low noise performance in a double-pass configuration. The main L-band amplifier is composed of two sections of EDFs. A 980 nm and a 1480 nm pump lasers are used to pump the first section of EDF bi-directionally. The generated backward C-band amplified spontaneous emission noise from this EDF is used to pump a subsequent un-pumped section of EDF. In the double-pass scheme, a narrow-band fiber Bragg grating at each channel wavelength is used to back-reflect the L-band signal to make it amplified twice by the pair of EDFs. Compared with its conventional counterpart, this new double-pass configuration provides a lower noise figure and a higher gain. The pump conversion efficiency can be improved by more than 50% in a 3-channel demonstration by using the proposed configuration.     

Multistage gain-flattened hybrid optical amplifier at reduced wavelength spacing

In this paper, two stage hybrid optical amplifier (HOA) composed of a single erbium doped fiber amplifier and Raman amplifier is proposed for dense wavelength division multiplexed (DWDM) system and investigate the impact of reduced channel spacing. The performance has been evaluated in the term of gain, gain flatness and noise figure. Also, using gain equalization technique, hybrid optical amplifier that has a gain flatness of 3 dB, and a noise figure of less than 7.4 dB is observed.     

Double-pass erbium-doped zirconia fiber amplifier for wide-band and flat-gain operations

The double-pass erbium-doped zirconia fiber amplifier (EDZFA) is proposed and demonstrated to provide a wide-band amplification as well as flat-gain operation in both the C- and L-band regions using only a single-gain medium. The proposed amplifier utilizes an erbium-doped zirconia fiber (EDZF) with erbium ion concentration of 2800 ppm as a gain medium. The medium is fabricated in a ternary glass host, zirconia-yttria-aluminum codoped silica fiber through solution doping technique along with modified chemical vapor deposition (MCVD). Compared to a single-pass operation, the double-pass EDZFA shows a better gain performance. At input signal power of 0 dBm and the optimum EDZF length of 2 m, a flat gain of around 16 dB is achieved by the proposed double-pass amplifier with gain variation of approximately 2.5 dB throughout the wavelength range from 1530 to 1590 nm. However, the noise figure of the double-pass amplifier is slightly higher than that of the single-pass due to inefficient population inversion at the input part of the amplifier.     

Gain ripple minimization in fiber Raman amplifiers based on variational method

In this paper, the variational method is employed for minimizing the gain ripple of multi-wavelength fiber Raman amplifiers. The variance of gain spectrum of the fiber Raman amplifier is regarded as the cost function, restriction on total pump power and average gain is given as the constraints of the minimization problem. It is shown that the minimization problem with any necessary constraints on the pump powers, average gain and signal to noise ratio, is reduced to a two-point boundary value problem. The method gives the entire possible local and global solutions. The method is applied to different examples of fiber Raman amplifiers with different lengths from 25 km to 100 km and different numbers of pumps from 4 to 20 to determine the pump powers and wavelengths for minimum gain ripple. It was obtained for a 100 km fiber Raman amplifier the gain ripple can be about 0.1 dB with on-off gain more than 20 dB.     

1410 nm波段分布式光纤拉曼增益放大器的研究

讨论了分布式光纤拉曼增益放大器的工作原理,采用1320nm固体激光器作为抽运源,获得了1410nm波段附近的光放大,在单模GI光纤长度为23km时,初步研究了拉曼放大器增益与光纤作用长度的关系,抽运脉冲峰值功率分别为50W、30W时,光纤的有效作用长度分别为15．5km和10.5km;研究了在不同的光纤有效作用长度时,拉曼放大器增益与抽运功率的关系;从光纤拉曼光谱图估算了光纤拉曼放大器的光谱宽度为50nm或250cm^-1。     

New trend for optical signal-to-noise ratio of disturbed Raman fiber amplifier

In a distributed Raman fiber amplifier (DRFA), Raman amplification allows a lower signal launch powers to transverse the span above the noise floor while still increasing the optical signal-to-noise ratio (OSNR). It improves the noise figure and reduces the nonlinear penalty of fiber systems. In this paper, we demonstrate a new trend of OSNR at different pump configurations: forward, backward and bidirectional pumping for DRFAs as a function of fiber length. We also present the variation of OSNR with both input pump power and input signal power. It is found that forward pumping provides the highest OSNR, reaching its maximum value of 37 dB. However, backward pumping provides the smallest OSNR that has its maximum of 22 dB and the bidirectional pumping provides the moderate OSNR between the others having its peak of 26 dB.     

The L-band EDFA of high clamped gain and low noise figure implemented using fiber Bragg grating and double-pass method

The L-band erbium-doped fiber amplifier (EDFA) of low noise figure and high clamped-gain using gain-clamped and double-pass configuration is presented in this paper. A total of five different configurations of EDFAs by reflection scheme with single forward pumping schemes are examined and compared here. Among these configurations, we first find the configuration of 1480-nm pumped L-band EDFA with optimum gain and noise figure value. To further minimize the gain variation, a fiber Bragg grating (FBG) with 1615-nm center wavelength and 1-nm bandwidth is determined and added in double-pass L-band EDFA. The gain variation and maximum noise figure of EDFA while channel dropping is investigated. As the number of channel dropping from 32 to 4, the L-band type-A EDFA keep the variation of gain within 2.9 dB and the maximum noise figure below 5 dB with each channel’s input power of −23 dBm.     

Multi-channel gain and noise figure evaluation of Raman/EDFA hybrid amplifiers

We present detailed multi-channel experimental characterization of different configurations of single pump hybrid Raman-erbium doped fiber (EDF) amplifiers. The incorporation of an EDF section in a dispersion compensating Raman amplifier is demonstrated to provide superior performance than Raman only system. It is shown that the multi-channel gain spectrum is quite different form the single-channel case. We have also measured the polarization dependent gain (PDG) of the hybrid amplifier configurations and results show that different configurations of hybrid amplifiers have different PDG effects on long-haul optically amplified link.     

Shooting algorithm and particle swarm optimization based Raman fiber amplifiers gain spectra design

An initial value determination method with a contraction factor for the counter-pumped Raman coupled equations is proposed. This method is used in conjunction with initial guess correction mechanism of Newton's method to construct a new efficient shooting algorithm for the solution of counter-pumped Raman coupled equations. The particle'swarm optimization is used to find the optimal wavelengths and powers for the pumps. By combining the new shooting algorithm and particle swarm optimization a powerful approach to the design of gain spectra for Raman fiber amplifiers is developed. Using this approach a counter-pumped broadband Raman fiber amplifier in C + L-band is designed and optimized. An average on-off gain of 9.3 dB for a bandwidth of 95 nm is obtained using only 4 pumps, with an in-band ripple level of ± 0.7 dB.     

An effective numerical method for gain profile optimizations of multi pumped fiber Raman amplifiers

In this paper, we have solved propagation equations of multi-pump fiber Raman amplifier using Runge–Kutta (RK 4th order) numerical method and pump power evolutions along with the fiber length. They are used to calculate the net gain and gain ripple by varying the input signals powers for different fiber lengths. The pump powers are optimized by genetic algorithm and resulting net gain and gain ripple are reported graphically as well as in tabular form. The optimum minimum gain ripple is 0.26 dB for 1 mW input signal powers for 50 km fiber length. By increasing the fiber length gain ripple increases to 0.5 dB for 0.1 mW input signal power. In comparison to other methods reported in the literature, our method is simple to implement and efficient for numerical design of Raman amplification in optical communication systems.     

L波段掺铒光纤放大器的自发辐射谱与增益的研究

利用Giles模型对L波段掺铒光纤放大器小信号增益特性进行了数值模拟,模拟结果表明最佳铒纤长度并不是一定值,它随输入信号波长的不同而改变,较短的波长对应较短的光纤长度;在数值模拟、分析的基础上,分别采用7m和9m的L波段铒光纤构成长波段掺铒光纤放大器,通过实验测量,分析比较了它们的自发辐射谱以及增益和噪声指数,得到了光纤长度对L波段增益谱、噪声指数和自发辐射谱的影响规律;最后,辅以C波段掺铒光纤放大器加以分析,指出了适合于放大L波段信号的最佳自发辐射谱型。     

Effect of sinusoidal ripples in refractive index profile distribution on the performance characteristics of dual concentric core step index fiber Raman amplifier

Phased matched wavelength, effective area, effective Raman gain, and wave guide dispersion are computed from exact numerical solution assuming scalar wave equation in the presence and absence of ripples as imperfections in the refractive index profile in dual cores of single mode fiber Raman amplifier for the first time. It is observed that for larger values of amplitude and lower frequencies, the effective Raman gain increases w.r.t. that calculated with no ripples. However, we assume ripple amplitude up to 5% of core cladding refractive index difference w.r.t. the available data, corresponding to the three ranges of relative ripple amplitudes of 1%, 2%, 3% and ripple frequencies of 1, 2, 3 μm⁻¹. Based on these data, we analyse performance of FRA over frequency shift band of 20–700 cm⁻¹. Uniformity of gain is interestingly seen to be maintained for higher ripple frequency and lower amplitude. However, no prominent effect in coefficient of dispersion and phase matched wavelength is observed within operating range of wavelength. Also, based on available structural parameter, the investigation should find use as a guide to system users to know the limit and promise of existence of ripples.     

Effect of Cascading Amplification Stages on the Performance of Serial Hybrid Fiber Amplifier

Abstract

This study demonstrates simulation and experimental validation of a wideband serial hybrid Raman/erbium-doped fiber amplifier. Two configurations are adopted; in type A, a Raman amplifier is the first stage, and in type B, an erbium-doped fiber amplifier is the first stage. At low input signal power, the average gain level is 20 dB with a flat gain bandwidth of 40 nm for both configurations. The noise figure in type B is dominated by the erbium-doped fiber amplifier and produces lower values and flatter spectra than in type A. The gain of the proposed hybrid amplifiers is affected more by the second amplification stage.     

Impacts of dispersion maps on nonlinear distortion in distributed Raman amplified multi-span systems

The influences of dispersion maps on three major nonlinear effects (SPM, XPM and SRS) in distributed Raman amplified fiber transmission systems with periodic dispersion compensation are numerically investigated at identical nonlinear phase shift. The results show that compared with lumped amplification, distributed amplification tends to enhance the SPM/XPM induced penalties provided per span complete DC is used. However, these performance differences can be canceled out by means of optimal dispersion managements. Moreover, distributed Raman amplification can change the optimal dispersion maps for XPM effects. On the other hand, the impacts of SRS crosstalk are mainly determined by wavelength spacing and walk-off parameter, and the effects of dispersion management are quite limited. For a system with properly designed fiber dispersion characteristics, SRS induced waveform distortion can be well suppressed.     

基于高非线性光纤的增益谱平坦拉曼光纤放大器研究

针对光纤通信中密集波分复用系统各信道的在线平坦光放大这一光通信问题,提出利用级联高非线性光纤来设计增益平坦的拉曼光纤放大器。对高非线性光纤(As S光纤)拉曼增益谱前后沿进行线性拟合处理,利用不同波长泵浦抽运同种光纤,实现前放大后增益补偿,并考虑信号光损耗不同,在输出端得到了一个近似固定的功率输出值,并分析了影响拉曼光纤放大器输出特性的因素。模拟结果表明:平均增益为20.45 dB,增益平坦度为0.15 dB。     

Gain clamped L-band EDFA with forward–backward pumping scheme using fiber Bragg grating

The paper proposes a novel two stage L-band erbium doped fiber amplifier with forward–backward pumping scheme for transmission of 32 wavelength division multiplexed (WDM) channels. It is gain clamped with an in-line fiber Bragg grating (FBG) to provide flat gain over 45 nm by restricting and reutilizing amplified spontaneous emission (ASE). We demonstrate that it provides an efficient small signal gain with minimum noise figure of over 20 dB and 5.5 dB, respectively, in the L-band region (1565–1610 nm) by comparing with its forward and backward pumped counterparts with fixed Er³⁺ fiber length of 20 m for −30 dBm/channel input power. We also obtain the gain and noise figure dependence as a function of each of the Er³⁺ fiber lengths, pump power (both 1480 and 980 nm), and temperature. Hence a 10 nm region (1580–1590 nm) has been acknowledged where temperature variations become constricted for 30 °C variations (15–45 °C).