Laser frequency stabilization at 1.5 microns using ultranarrow inhomogeneous absorption profiles in Er:LiYF4

Single-frequency diode lasers have been frequency stabilized to 1.5 kHz Allan deviation over 0.05-50 s integration times, with laser frequency drift reduced to less than 1.4 kHz/min, using the frequency reference provided by an ultranarrow inhomogeneously broadened Er³⁺:⁴I_15/2→⁴I_13/2 optical absorption transition at a vacuum wavelength of 1530.40 nm in a low-strain LiYF₄ crystal. The 130 MHz full-width at half-maximum (FWHM) inhomogeneous line width of this reference transition is the narrowest reported for a solid at 1.5 μm. Strain-induced inhomogeneous broadening was reduced by using the single isotope ⁷Li and by the very similar radii of Er³⁺ and the Y³⁺ ions for which it substitutes. To show the practicability of cryogen-free cooling, this laser stability was obtained with the reference crystal at 5 K; moreover, this performance did not require vibrational isolation of either the laser or crystal frequency reference. Stabilization is feasible up to T=25 K where the Er³⁺ absorption thermally broadens to ∼500 MHz. This stabilized laser system provides a tool for interferometry, high-resolution spectroscopy, real-time optical signal processing based on spatial spectral holography and accumulated photon echoes, secondary frequency standards, and other applications such as quantum information science requiring narrow-band light sources or coherent detection.     

Continuous-wave high-power multi-pass pumped thin-disc Nd:GdVO4 laser

A thin-disc Nd:GdVO₄ laser in multi-pass pumping scheme was developed. Continuous-wave output power of 13.9 W at 1.06 μm for an absorbed power at 808 nm of 22 W was demonstrated from a 250-μm thick, 0.5-at.% Nd:GdVO₄ in a 4-pass pumping; the slope efficiency in absorbed power was 0.65, or 0.47 in input power. Output performances were also investigated under diode laser pumping at 879 nm, directly into the emitting ⁴F_3/2 level: maximum power of 3.6 W was obtained at 6.2 W of absorbed power with 0.69 slope efficiency. Compared with pumping at 808 nm, into the highly absorbing ⁴F_5/2 level, improvements of laser parameter in absorbed power (increase of slope efficiency, decrease of threshold) were obtained, showing the advantages of the pumping into the emitting level. However, the laser performances expressed vs. the incident power were modest owing to the low absorption efficiency at 879 nm. Thus, increased number of passes of the medium would be necessary in order to match the performances in input power obtained under 808-nm pumping.     

Self-Q-switching and mode-locking in an all-fiber Er/Yb co-doped fiber ring laser

Using a section of un-pumped Er/Yb co-doped fiber (EYDF) as a saturable absorber, Self-Q-switching and self-mode-locking pulses have been obtained in an all-fiber EYDF ring laser. Such laser is with the self-Q-switched pulse threshold of 135.22 mW, the repetition rate of approximately 22.2 kHz, and the pulse duration of ∼2.8 μs, respectively. The self-mode-locked threshold is 591.8 mW. By incorporating the saturable absorption in an un-pumped EYDF and a Mach-Zehnder interferometer, when the pump power is increased to 1242.9 mW, the continuous-wave (CW) mode-locking with the pulse width of 26 ns has also been demonstrated experimentally for the first time.     

Continuous-wave broadly tunable Cr:ZnSe laser pumped by a thulium fiber laser

We describe a compact, broadly tunable, continuous-wave (cw) Cr²⁺:ZnSe laser pumped by a thulium fiber laser at 1800 nm. In the experiments, a polycrystalline ZnSe sample with a chromium concentration of 9.5 × 10¹⁸ cm⁻³ was used. Free-running laser output was around 2500 nm. Output couplers with transmissions of 3%, 6%, and 15% were used to characterize the power performance of the laser. Best power performance was obtained with a 15% transmitting output coupler. In this case, as high as 640 mW of output power was obtained with 2.5 W of pump power at a wavelength of 2480 nm. The stimulated emission cross-section values determined from laser threshold data and emission measurements were in good agreement. Finally, broad, continuous tuning of the laser was demonstrated between 2240 and 2900 nm by using an intracavity Brewster cut MgF₂ prism and a single set of optics.     

Self-Q-switched and mode-locked Nd,Cr:YAG laser with 6.52-W average output power

Simultaneous self-Q-switched and mode-locked have been demonstrated in a diode-pumped Nd,Cr:YAG laser. For the first time as we know, almost 100% modulation depth has been achieved at an intracavity intensity of 5.6 × 10⁵ W/cm². The maximum average output power of 6.52 W corresponding to a slope efficiency of 30% is obtained at 1064 nm. The laser produces high-quality pulses in a TEM₀₀-mode at the pump power of 16.5 W. The pulse duration of the mode-locked pulses is about 600 ps with 136 MHz repetition rate.     

Diode-pumped passively Q-switched Nd:LuVO4 laser at 916 nm

We demonstrate a passively Q-switched Nd:LuVO₄ laser at 916 nm by using a Nd, Cr:YAG crystal as the saturable absorber. As we know, it is the first time to realize the laser with a simple linear resonator. When the incident pump power increased from 14.6 W to 23.7 W, the pulse width of the Q-switched laser decreased from 24 ns to 21 ns. The pulse width was insensitive to the incident pump power in the experiment. The average output power of 288 mW with repetition rate of 39 kHz was obtained at an incident pump power of 22.5 W, with the optical-to-optical efficiency and slope efficiency 1.3% and 3.6%, respectively.     

LD end pumped, actively mode locked and passively Q-switched Nd:YAP laser at 1341 nm

An end pumped Nd:YAP laser at 1341 nm is actively mode locked and passively Q-switched. Pumping was done with a pulsed high power laser diode with maximum power 425 W. V³⁺:YAG with 61% initial transmission served as saturable absorber, and an acousto-optic modulator is used for active mode locking. The output pulse train with 69 ns duration has a total energy of 3.2 mJ with ±4% shot-to-shot fluctuation. The peak output energy of a single mode locked pulse is 0.25 mJ. The pulse duration of a single mode locked pulse is less than 800 ps. The output laser beam is nearly diffraction limited with 1.6 mm diameter, and beam propagation factor M² about 1.3.     

Self-Q-switched and mode-locked 946 nm Cr,Nd:YAG laser

A simultaneous self-Q-switched and mode-locked diode-pumped 946 nm laser by using a Cr,Nd:YAG crystal as gain medium as well as saturable absorber is demonstrated for the first time as we know. The maximum average output power of 751 mW with a slope efficiency of 18.38% is obtained at an intra-cavity average peak power intensity of 4.83 × 10⁶ W/cm². Under this circumstance, the repetition rate of Q-switched envelopes is 9.63 kHz and the pulse width is about 460 ns. Almost 100% mode-locked modulation depth is obtained at all time in the experiment process whether the incident pump power is low or high. The repetition rate of mode-locked pulses within a Q-switched envelope is 135.13 MHz and the mode-locked pulse width is within 600 ps. The laser produces high-quality pulses in TEM₀₀-mode in the simultaneous self-Q-switched and mode-locked experiment.     

Efficient generation of 200 mJ nanosecond pulses at 100 Hz repetition rate from a cryogenic cooled Yb:YAG MOPA system

A diode-pumped Master Oscillator Power Amplifier (MOPA) laser system based on cryogenic cooled Yb:YAG has been designed, developed and its output performance characterised. The laser system consists of a fibre oscillator, an active mirror regenerative amplifier and a four pass main amplifier. 2.4 mJ, 10 ns, 100 Hz seed pulses from the fibre oscillator/regenerative amplifier arrangement were amplified up to pulse energies of over 200 mJ by using the four pass main amplifier arrangement. As a further study we have obtained an increased slope efficiency of 40% and an optical-to-optical efficiency of 30% using a pinhole vacuum spatial filter/image relay for laser mode control. With 1.8 mJ input seed pulses, output pulse energies of around 150 mJ were achieved.     

Offset frequency locking for nanosecond laser pulses

A method of multi-pulse discriminating frequency and high probability average value filtering is presented for offset frequency locking with ns laser pulses. In the experiment, the frequency locking for cavity-dumped CO₂ laser with 100 ns pulse width and the repetition rate of 10 kHz was studied. The precision was up to ±2 MHz at the heterodyne frequency 90 MHz. However, it is more than ±10 MHz for the single pulse discriminating frequency. This method can also be applied to laser offset frequency locking for many kinds of short pulse lasers.     

Diode-end-pumped linear-polarized single-frequency Tm:YAG laser at room temperature

By using two solid uncoated etalons, we present a diode-pumped linear-polarized single-frequency Tm:YAG laser operating at 2 μm. Placing one 0.1 mm F-P etalon at nearly Brewster angle in the cavity, the linear-polarization laser is achieved. The other 1 mm F-P etalon was turned in the range of very small angle, single-longitudinal-mode (SLM) could be obtained. The maximum output power of linear-polarized single-frequency laser of 60 mW is achieved at the wavelength of 2013 nm. The degree of the polarization is over 30 dB. Long-term frequency stability was also investigated, with the results of wavelength fluctuation about 2.55 × 10⁻¹³ m within 3 min and frequency change about 18.86 MHz, corresponding to a frequency stability of 1.27 × 10⁻⁷.     

High-beam-quality, 5.1 J, 108 Hz diode-pumped Nd:YAG rod oscillator-amplifier laser system

A high efficiency, high beam quality diode-pumped Nd:YAG master oscillator power-amplifier (MOPA) laser with six amplifier stages is demonstrated. The oscillator with two-rod birefringence compensation was designed as a thermally determined near hemispherical resonator, which presents a pulse energy of 223 mJ with a beam quality value of M² = 1.29 at a repetition rate of 108 Hz. The MOPA system delivers a pulse energy of 5.1 J with a pulse width of 230 μs, a M² factor of 3.6 and an optical-to-optical efficiency of 38.5%. To the best of our knowledge, this is the highest pulse energy for a diode-pumped Nd:YAG rod laser operation with a high beam quality and a pulse width of hundreds of microseconds at a repetition rate of over 100 Hz.     

Efficient passively Q-switched operation of a diode-pumped Nd:GGG laser with a Cr:YAG saturable absorber

The continuous-wave (cw) and passive Q-switching operation of a diode-end-pumped gadolinium gallium garnet doped with neodymium (Nd:GGG) laser at 1062 nm was realized. A maximum cw output power of 6.9 W was obtained. The corresponding optical conversion efficiency was 50.9%, and the slope efficiency was determined to be 51.4%. By using Cr⁴⁺:YAG crystals as saturable absorbers, Q-switching pulse with average output power of 1.28 W, pulse width of 4 ns and repetition rate of 6.2 kHz were obtained. The single-pulse energy and peak power were estimated to be 206 μJ and 51.6 kW, respectively. The conversion efficiency of the output power from cw to Q-switching operation was as high as 84.7%.     

High efficiency TEM00 mode, diode-pumped, conduction-cooled, Nd:YAG zig-zag slab laser

We report a compact, conduction-cooled, highly efficient, continuous wave (CW) Nd:YAG slab laser in diode-side-pumped geometry. To achieve high efficiency, a novel laser head for Nd:YAG slab has been developed. For an absorbed pump power of 27.6 W, maximum output power of 10.4 W in multimode and 8.2 W in near-diffraction-limited beam quality has been obtained. Slope and optical-to-optical conversion efficiencies are 45.3% and 37.7% in multimode with beam quality factors (M²) in x and y directions equal to 32 and 8, respectively. TEM₀₀ mode operation was achieved in a hybrid resonator with slope and optical-to-optical conversion efficiencies of 43.2% and 29.7%, respectively. Beam quality factors in x and y directions are ?1.5 and ?1.6 for the whole output power range. The laser radiation was linearly polarized and polarization contrast ratios are >1200:1 in the multimode and 1800:1 in the TEM₀₀ mode operation. In passive Q-switching with Cr⁴⁺:YAG crystal of 68% initial transmission, 18 ns pulsewidth has been achieved with an average power of 2 W at a repetition rate of 16 kHz.     

All-fiber actively Q-switched Yb-doped laser

An all-fiber actively Q-switched Yb-doped laser is presented. Q-switching is performed by modulating a fiber Bragg grating via a magnetostrictive rod which is fixed to the fiber at the position of the grating. By exposing the rod to a changing magnetic field, the rod is stretched and relaxed causing the Bragg wavelength of the grating to shift and thereby changes the Q-factor of the cavity. Using Yb-doped fiber, pulses at 1052 nm are obtained at repetition rates from 1 to 200 kHz. At 75 kHz, 0.5 μJ pulses with peak powers of 3 W can be produced when 180 mW of pump power is applied. To the knowledge of the authors, this is the first all-fiber actively Q-switched Yb-doped laser presented to date.     

Diode-pumped passively Q-switched mode-locked Nd:YLF laser with uncoated GaAs saturable absorber

We have demonstrated passively Q-switched mode-locked all-solid-state Nd:YLF laser with an uncoated GaAs wafer as saturable absorber and output mirror simultaneously. Q-switched mode-locking pulses laser with about 100% modulation depth were obtained. The average output power is 890 mW at the incident pump power of 5.76 W, corresponding to an optical slop efficiency of 20%. The temporal duration of mode-locked pulses was about 21 ps. At the Q-switched repetition rate of 30 kHz, the energy and peak power of a single pulse near the maximum of the Q-switched envelope was estimated to be about 1.6 μJ and 76 kW.     

Reflective carbon nanotube as the saturable absorber for mode-locked 1064 nm laser

With a reflective single-walled carbon nanotube as the saturable absorber, a laser diode-pumped passively mode-locked Nd:YVO₄ laser at 1064 nm was realized for the first time. The pulse duration of 12 ps was produced with a repetition rate of 83.7 MHz. The peak power and the single pulse energy of the mode-locking laser were 1.28 kW and 15.4 nJ, respectively.     

Effect of the spiral phase element on the radial-polarization (0, 1) LG beam

Radially-polarized beams can be strongly amplified without significant birefringent-induced aberrations. However, radially-polarized beam is a high-order beam, and therefore has to be transformed into a fundamental Gaussian beam for reduction the beam-propagation factor M². In effort to transform the radially-polarized beam to a nearly-Gaussian beam, we consider effect of a spiral phase element (SPE) on the Laguerre-Gaussian (LG) (0, 1)^∗ beam with radial polarization, and compare this with the case when the input beam is a LG (0, 1)^∗ beam with spiral phase and uniform or random polarization. The LG (0, 1)^∗ beam with radial polarization, despite its identity in intensity profile to the beam with spiral phase, has distinctly different properties when interacting with the SPE. With the SPE and spatial filter, we transformed the radially-polarized (0, 1)^∗ mode with M² = 2.8 to a nearly-Gaussian beam with M² = 1.7. Measured transformation efficiency was 50%, and the beam brightness P/(M²)² was practically unchanged. The SPE affects polarization state of the radially-polarized beam, leading to appearance of spin angular momentum in the beam center at the far-field.     

Continuous-wave operation of a room-temperature Ho:YAP laser pumped by a Tm:YAP laser

We reported the Ho:YAP laser pumped by the Tm:YAP laser. The Ho:YAP laser maximum output power was 4.91 W when the incident power was 10.1 W with the threshold of 2.63 W. The slope efficiency was 63.7%, corresponding to an optical-to-optical efficiency of 48.6%. The Ho:YAP output wavelength was centered at 2118.2 nm with bandwidth of about 1 nm. We estimate the beam quality to be M² = 1.29.     

43 W picosecond laser and second-harmonic generation experiment

Combining the advantages of diode-end-pumped Nd: YVO₄ and diode-side-pumped Nd: YAG amplifiers, a high average power and high beam quality picosecond laser is designed. The system delivers a picosecond laser with average power of 43.4 W and good beam quality of M² < 1.7. By focusing the high power picosecond laser in LBO crystal, 532 nm green laser with maximal power of 20.8 W is generated and the conversion efficiency of second-harmonic generation reaches 56.4% when 17.7 W green laser obtained from the fundamental frequency laser with power of 31.4 W and beam quality of M² < 1.25.