1 Gbit/s transmission over step-index plastic optical fiber using an optical receiver with an integrated equalizer

A single chip optical receiver with an integrated large-diameter photodiode, transimpedance amplifier, two stages active equalizer, post amplifier and 50 Ω driver is used for gigabit transmission over PMMA step plastic optical fiber (SI-POF). The large-diameter photodiode with an antireflection coating optimized for red light. The integrated equalizer enables the presented optical receiver to reach 1 Gbit/s over 50 m SI-POF at bit error ratio of 10^− 6. An error free (< 10^− 9) 1 Gbit/s data rate over 40 m standard PMMA step-index plastic optical fiber is also achieved.     

Numerical analysis and system optimization for 100 Gbit/s carrier Ethernet serial modulation formats

The performance of various modulation schemes for 100 Gbit/s single-channel serial transmission is investigated by means of numerical simulations. Different ASK and PSK modulation formats are compared in terms of total system reach for a 10⁻⁹ BER requirement. RZ-DQPSK format with a 1920 km reach, without FEC and without the support of additional Raman amplification, outperforms all the other schemes including 10 × 10 Gbit/s NRZ DWDM inverse multiplexing.     

The analysis of the error statistics in a 5 × 40 Gbit/s fibre link with hybrid amplification

We quantify the error statistics and patterning effects in a 5 × 40 Gbit/s WDM RZ-OOK SMF/DCF fibre link using hybrid Raman/EDFA amplification. By extensive use of a numerical model, we determine how the error statistics change with the transmission distance. This knowledge is used as a basis for a constrained coding technique in order to improve the transmission error rate. We propose an adaptive constrained code for mitigation of the patterning effects and demonstrate that this approach can substantially reduce the bit error rate (BER) even for very large values of the channel BER (BER > 10^− 1). The proposed technique can be used in combination with forward error correction schemes (FEC) to extend the range of channel BERs that an FEC scheme is effective over.     

The ν1 + 3ν2 + 3ν3 and 4ν1 + ν2 + ν3 bands of ozone by CW-cavity ring down spectroscopy between 5900 and 5960 cm

The absorption spectrum of ozone, ¹⁶O₃, has been recorded in the 5903-5960 cm⁻¹ region by high sensitivity CW-cavity ring down spectroscopy (α_min ∼ 5 × 10⁻¹⁰ cm⁻¹). The ν₁ + 3ν₂ + 3ν₃ and 4ν₁ + ν₂ + ν₃ A-type bands centred at 5919.15 and 5947.07 cm⁻¹ were newly observed. A set of 173 and 168 energy levels could be experimentally determined for the (1 3 3) and (4 1 1) states, respectively. Except for a few K_a = 5 levels of the (4 1 1) state, the rotational structure of the two states was found mostly unperturbed. The spectroscopic parameters were determined from a fit of the corresponding line positions by considering the (1 3 3) and (4 1 1) states as isolated. The determined effective Hamiltonian and transition moment operators were used to generate a list of 785 transitions given as Supplementary Material.     

Perpendicular magnetic recording technology at 230 Gbit/in

A perpendicular recording system that allows areal densities beyond 200 Gbit/in² has been designed and tested to investigate the major challenges in perpendicular magnetic recording. The integrated write/read head has a trailing shield to improve the write head field gradient and a conventional CIP–GMR reader. The medium is a low-noise CoPtCr-based oxide medium with a CoTaZr soft underlayer. On track byte error rates at ∼ 50 Mb/s are better than 10⁻⁴ at ∼1000 kbpi. Using a 15% off-track criterion at 10⁻² byte error rate, track densities between 200–240 ktpi are realized, yielding areal densities of 210–233 Gbit/in². High-resolution magnetic force microscopy (hrMFM) has been employed to investigate the write characteristics of these heads with improved cross-track resolution. Using a quantitative analysis method, many parameters, such as transition curvature and transition width, are estimated from the hrMFM image. Significant transition curvature is found, which increases the width of the read head response to a transition, T₅₀, by 2–3 nm.These results give insights into the recording physics of perpendicular recording and in particular point out improvements required for achieving even higher areal densities.     

Characterization of single-crystalline In2O3 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

Epitaxial In₂O₃ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates by metalorganic chemical vapor deposition (MOCVD). The films were deposited at different substrate temperatures (450-750 °C). The film deposited at 650 °C has the best crystalline quality, and observation of the interface area shows a clear cube-on-cube epitaxial relationship of In₂O₃(1 0 0)||YSZ(1 0 0) with In₂O₃[0 0 1]||YSZ[0 0 1]. The Hall mobility of the single-crystalline In₂O₃ film deposited at 650 °C is as high as 66.5 cm² V⁻¹ s⁻¹ with carrier concentration of 1.5 × 10¹⁹ cm⁻³ and resistivity of 6.3 × 10⁻³ Ω cm. The absolute average transmittance of the obtained films in the visible range exceeds 95%.     

Intracavity Laser Absorption Spectroscopy of D2O between 12 850 and 13 380 cm

The high resolution absorption spectrum of dideuterated water, D₂O, has been recorded by Intracavity Laser Absorption Spectroscopy (ICLAS) in the 12 850-13 380 cm⁻¹ spectral region which is the higher energy region reported so far for this water isotopologue. Very high deuterium enrichment was necessary to minimize the HDO absorption lines overlapping the D₂O spectrum. The achieved sensitivity (noise equivalent absorption α_min ∼ 10⁻⁹ cm⁻¹) allowed detecting transitions with line strengths on the order of 5 × 10⁻²⁸ cm/molecule. The spectrum analysis, based on recent variational calculations has provided a set of 422 new rovibrational energy levels belonging to 11 vibrational states, including rotational sublevels for four new vibrational states and one level of the (0 9 1) highly excited bending state. The very weak (1 0 4)-(0 0 0) band at 13 263.902 cm⁻¹, which is the highest D₂¹⁶O band currently observed, could be assigned despite the fact that the HDO absorption in the region is stronger by three orders of magnitude. The list of 996 D₂¹⁶O transitions is provided as Supplementary Material.     

Numerical analysis of amplification characteristics of ErxY2 − xSiO5

The gain characteristics of Er_xY_2 − xSiO₅ waveguide amplifiers have been investigated by solving rate equations and propagation equations. The gain at 1.53 μm as a function of waveguide length, Er³⁺ concentration and pump power is studied pumping at three different wavelengths of 654 nm, 980 nm and 1480 nm, respectively. The optimum Er³⁺ concentrations of 1 × 10²¹ cm^− 3-2 × 10²¹ cm^− 3 with the high gain are obtained for all three pump wavelengths. Pumping at 654 nm wavelength is shown to be the most efficient one due to weak cooperative upconversion. A maximum 16 dB gain at 1 mm waveguide length under a 30 mW pump with Er³⁺ concentration of 1 × 10²¹ cm^− 3 is demonstrated pumping at 654 nm wavelength.     

Synthesis and electrical conductivity of various melilite-type electrolytes Ln1 + xSr1 − xGa3O7 + x/2

Melilite type ceramics ABC₃O₇ such as La_1.54Sr_0.46Ga₃O_7.27 are a new class of oxide conductors where the conductivity is carried out through interstitial oxygen ions. This work presents the attempt to replace the A-site element La with the other lanthanide elements and Y, resulting in various Ln_1 + xSr_1 − xGa₃O_7 + x/2 ceramics, in which Ln = La, Pr, Nd, Sm, Eu, Gd, Dy, Yb, Y, and 0.1 < x < 0.54. X-ray diffraction analysis shows that the melilite structure could be formed when the replacement is conducted with most lanthanides but not Yb and Y. Impedance spectroscopy demonstrates that the conductivity decreases dramatically with the decreasing of Ln³⁺ size and the charge-carrier concentration. These results suggest that, as an interstitial oxide ion electrolyte, La_1.54Sr_0.46Ga₃O_7.27 is the most promising ceramic in the Ln_1 + xSr_1 − xGa₃O_7+x/2 melilite family since La³⁺ has the largest ionic radius of the lanthanide elements.     

High-resolution FTIR and MMW study of the v4 = 2 (A1, E) excited state of NF3 near 985 cm: the axial ground state rotational constants derived by the “loop-method”

The two substates v₄ = 2⁰ (A₁, 983.702 cm⁻¹) and v₄ = 2^±2 (E, 986.622 cm⁻¹) of the oblate symmetric top molecule, ¹⁴NF₃, have been studied by high-resolution (2.5 × 10⁻³ cm⁻¹) infrared spectroscopy of the overtones and 2ν₄ − ν₄ hot bands. Transitions of the overtone, the hot band, and the previously measured fundamental band were combined to yield 585 ground state combination differences differing in K by ±3, with K_max = 36. Using the “loop-method,” a fit (standard deviation σ = 0.320 × 10⁻³ cm⁻¹) provided a complete set of the hitherto not experimentally known axial ground state constants. In units of cm⁻¹ these have the following values: . Upper state parameters were determined using a vibrationally isolated model. Considering l (2, 2) and l (2, −1) interactions between the v₄ = 2⁰ and v₄ = 2^±2 substates and effects accounting for the l (4, −2) interactions within the kl = −2 levels, 25 upper state parameters were obtained by fitting 2747 IR data (1842 transitions, 905 deduced energies, J_max = 42, K_max = 39) with σ_IR = 0.353 × 10⁻³ cm⁻¹. Moreover, millimeter-wave spectroscopy furnished 86 transitions (J_max = 16, K_max = 13) measured on the v₄ = 2 excited state. A merged fit, refining 24 parameters using the described model gave σ_IR = 0.365 × 10⁻³ cm⁻¹ andσ_MMW = 0.855 × 10⁻⁶ cm⁻¹ (26 kHz). The anharmonicity constants (in cm⁻¹) are x₄₄ = −0.84174 (2) and g₄₄ =  + 0.73014 (1). In addition to this model, the D, Q, and L reductions of the rovibrational Hamiltonian were tested. Standard deviations σ_IR = 0.375 × 10⁻³ cm⁻¹ and σ_MMW = 0.865 × 10⁻⁶ cm⁻¹ were obtained for both D and L reductions, and σ_IR = 0.392 × 10⁻³ cm⁻¹ and σ_MMW = 0.935 × 10⁻⁶ cm⁻¹ for Q reduction. The unitary equivalence of the majority of the 18 tested relations between the derived parameters was satisfactorily fulfilled. This confirms that the v₄ = 2 excited vibrational state can be considered in reasonable approximation to be isolated.     

Rotational levels of the (0 0 0) and (0 1 0) states of D2O from hot emission spectra in the 320-860 cm region

The far-infrared emission spectra of deuterated water vapour were measured at different temperatures (1370, 1520, and 1950 K) in the range 320-860 cm⁻¹ at a resolution of 0.0055 cm⁻¹. The measurements were performed in an alumina cell with an effective length of hot gas of about 50 cm. More than 1150 new measured lines for the D₂¹⁶O molecule corresponding to transitions between highly excited rotational levels of the (0 0 0) and (0 1 0) vibrational states are reported. These new lines correspond to rotational states with higher values of the rotational quantum numbers compared to previously published determinations: J_max=26 and for the (0 0 0) ← (0 0 0) band, J_max=25 and for the (0 1 0) ← (0 1 0) band, and J_max=26 and for the (0 1 0) ← (0 0 0) band. The estimated accuracy of the measured line positions is 0.0005 cm⁻¹. To our knowledge no experimentally measured rotational transitions for D₂¹⁶O within an excited vibrational state have been available in the literature so far. An extended set of experimental rotational energy levels for (0 0 0) and (0 1 0) vibration states including all previously available data has been determined. For the data reduction we used the generating function model. The root mean square (RMS) deviation between observed and calculated values is 0.0012 cm⁻¹ for 692 rotational levels of the (0 0 0) state and 0.0010 cm⁻¹ for 639 rotational levels of the (0 1 0) vibrational state. A comparison of the observed energy levels with the best available values from the literature and with the global predictions from molecular electronic potential energy surface [J. Chem. Phys. 106 (1997) 4618] for the (0 0 0) and (0 1 0) states is discussed.     

Polarization maintaining holey fibers for residual dispersion compensation over S + C + L wavelength bands

We report on a highly birefringent holey fiber for broadband dispersion compensation covering the S, C, and L telecommunication bands i.e. wavelength ranging from 1460 to 1625 nm. The finite element method with circular perfectly matched layer boundary condition is used to investigate the guiding properties. Numerical analysis demonstrates that it is possible to obtain negative dispersion coefficient of about −470 to −850 ps/nm/km over S to L-bands and a relative dispersion slope perfectly matched with single mode fiber (SMF) of about 0.0036 nm⁻¹ at 1550 nm. At the same time birefringence of the order 2.53 × 10⁻² is realized at 1550 nm wavelength. Owing to superior optical properties of the proposed holey fiber, this can be a promising candidate for broadband dispersion compensation and sensing applications.     

A density functional theory study of ethylene adsorption on Ni10(1 1 1), Ni13(1 0 0) and Ni10(1 1 0) surface cluster models and Ni13 nanocluster

Ethylene adsorption was studied by use of DFT/B3LYP with basis set 6-31G(d,p) in Gaussian’03 software. It was found that ethylene has adsorbed molecularly on all clusters with π adsorption mode. Relative energy values were calculated to be −50.86 kcal/mol, −20.48 kcal/mol, −32.44 kcal/mol and −39.27 kcal/mol for Ni₁₃ nanocluster, Ni₁₀(1 1 1), Ni₁₃(1 0 0) and Ni₁₀(1 1 0) surface cluster models, respectively. Ethylene adsorption energy is inversely proportional to Ni coordination number when Ni₁₀(1 1 1), Ni₁₃(1 0 0) and Ni₁₀(1 1 0) cluster models and Ni₁₃ nanocluster are compared with each other.     

High-temperature electrical properties of magnesiowustite Mg1 − xFexO and spinel Fe3 − x − yMgxCryO4 ceramics

Phase relationships, thermal expansion and electrical properties of Mg_1 − xFe_xO (x = 0.1-0.45) cubic solid solutions and Fe_{3 − x − y}Mg_xCr_yO_4 ± δ (x = 0.7-0.95; y = 0 or 0.5) spinels were studied at 300-1770 K in the oxygen partial pressure range from 10 Pa to 21 kPa. Increasing iron content enlarges the spinel phase stability domain at reduced oxygen pressures and elevated temperatures. The total conductivity of the spinel ceramics is predominantly n-type electronic and is essentially p(O₂)-independent within the stability domain. The computer simulations using molecular dynamics technique confirmed that overall level of ion diffusion remains low even at high temperatures close to the melting point. Temperature dependencies of the total conductivity in air exhibit a complex behavior associated with changing the dominant defect-chemistry mechanism from prevailing formation of the interstitial cations above 1370-1470 K to the generation of cation vacancies at lower temperatures, and with kinetically frozen cation redistribution in spinel lattice below 700-800 K. The average thermal expansion coefficients of the spinel ceramics calculated from dilatometric data in air vary in the range (9.6-10.0) × 10^− 6 K^− 1 at 300-500 K and (13.2-16.1) × 10^− 6 K^− 1 at 1050-1370 K. Mg_1 − xFe_xO solid solutions undergo partial decomposition on heating under oxidizing and mildly reducing conditions, resulting in the segregation of spinel phase and conductivity decrease.     

The bΣ(b0) → XΣ(X10,X21) and aΔ(a2) → X21 transitions of AsBr

Emission spectra of the b¹Σ⁺(b0⁺) → X³Σ⁻(X₁0⁺,X₂1) and a¹Δ(a2) → X₂1 transitions of AsBr have been measured in the near-infrared spectral region with a Fourier-transform spectrometer. The arsenic bromide radicals were generated in fast-flow systems by reaction of arsenic vapor (As_x) with bromine and were excited by microwave-discharged oxygen. The most prominent features in the spectrum are the Δv = +1,0,−1, and −2 band sequences of the b¹Σ⁺(b0⁺) → X³Σ⁻(X₁0⁺) transition in the range 11 700-12 700 cm⁻¹. With lower intensities, the Δv = 0 and −1 sequences of the b¹Σ⁺(b0⁺) → X³Σ⁻(X₂1) sub-system show up in the same range. Further to the red, between 6000 and 6700 cm⁻¹, the Δv = 0, +1, and −1 sequences of the hitherto unknown a¹Δ(a2) → X₂1 transition are observed. Analyses of medium- and high-resolution spectra have yielded improved molecular constants for the X₁0⁺, X₂1, and b0⁺ states and first values of the electronic energy and the vibrational constants of the a2 state.     

Intracavity laser absorption spectroscopy of HDO between 12 145 and 13 160 cm

The high resolution absorption spectrum of monodeuterated water, HDO, has been recorded by Intracavity Laser Absorption Spectroscopy (ICLAS) in the 12 145-13 160 cm⁻¹ region. The achieved sensitivity (noise equivalent absorption on the order of α_min ∼ 10⁻⁹ cm⁻¹) allowed detecting transitions with line strengths as weak as 10⁻²⁷ cm/molecule which is about 50 times lower than the weakest line intensities previously detected in the considered region.The rovibrational assignment of the 1179 lines attributed to the HDO isotopologue was based on the results of the variational calculations of Schwenke and Partridge as well as the recent calculations based on a new HDO potential energy surface refined from the fitting to the available experimental data. The overall agreement between these new calculations and the observed spectrum is very good, the rms deviation of the differences between the calculated and observed energy values being 0.05 cm⁻¹. A set of 304 new experimental HDO energy levels was obtained. In particular, band origins for the (1 2 2), (2 0 2), and (3 1 1) vibrational states, at 12 568.190, 12 644.652, and 12 919.938 cm⁻¹, respectively, and their rotational sublevels are derived for the first time. A detailed HDO database of 1337 transitions was constructed and is provided as Supplementary Material.     

Laser excitation spectrum of C3 in the region 26 000-30 700 cm

The vibrational structure of the electronic state of C₃ in the region 26 000-30 775 cm⁻¹ has been re-examined, using laser excitation spectra of jet-cooled molecules. Rotational constants and vibrational energies have been determined for over 60 previously-unreported vibronic levels; a number of other levels have been re-assigned. The vibrational structure is complicated by interactions between levels of the upper and lower Born-Oppenheimer components of the state, and by the effects of the double minimum potential in the Q₃ coordinate, recognized by Izuha and Yamanouchi [16]. The present work shows that there is also strong anharmonic resonance between the overtones of the ν₁ and ν₃ vibrations. For instance, the levels 2 1⁺ 1 and 0 1 ⁺ 3 are nearly degenerate in zero order, but as a result of the resonance they give rise to two levels 139 cm⁻¹ apart, centered about the expected position of the 2 1⁺ 1 level. With these irregularities recognized, every observed vibrational level up to 30 000 cm⁻¹ (a vibrational energy of over 5000 cm⁻¹) can now be assigned. A vibronic level at 30181.4 cm⁻¹, which has a much lower B′ rotational constant than nearby levels of the state, possibly represents the onset of vibronic perturbations by the electronic state; this state is so far unknown, but is predicted by the ab initio calculations of Ahmed et al. [36].     

High sensitivity ICLAS of D2O between 12 450 and 12 850 cm

The weak absorption spectrum of dideuterated water, D₂O, has been recorded between 12 450 and 12 850 cm⁻¹ by high sensitivity Intracavity Laser Absorption Spectroscopy (ICLAS). This spectral region corresponds to the (ν₁ + ν₂/2 + ν₃) = 5 polyad, dominated by the 4ν₁ + ν₃ band centered at 12 743.035 cm⁻¹. The achieved sensitivity has allowed for the detection of lines with a minimum intensity of 2 × 10⁻²⁸ cm/molecule i.e. typically two orders of magnitude lower than previous observations in the region considered. A total of 586 energy levels belonging to 11 vibrational states were determined. The rovibrational assignment process of 1025 lines ascribed to D₂O was based on new results of variational calculations by Shirin et al. [S.V. Shirin, N.F. Zobov, O.L. Polyansky, J. Quant. Spectrosc. Radiat. Transfer, in press, doi:10.1016/j.jqsrt.2007.07.010]. The overall agreement between these calculations and the observed spectrum is good both for the line positions and line intensities. The difficulties encountered while performing the rovibrational labeling and the assignment of the weakest transitions not included in Combination Differences relations, are discussed.     

Driving force for the WO3(0 0 1) surface relaxation

The optimized structure of the WO₃(0 0 1) surface with various types of termination ((1 × 1)O, (1 × 1)WO₂, and c(2 × 2)O) has been simulated using density functional theory with the Perdew-Wang 91 gradient corrected exchange-correlation functional. While the energy of bulk WO₃ depends weakly on the distortions and tilting of the WO₆ octahedra, relaxation of the (0 0 1) surface results in a significant decrease of surface energy (from 10.2 × 10⁻² eV/Ų for the cubic ReO₃-like, c(2 × 2)O-terminated surface to 2.2 × 10⁻² eV/Ų for the relaxed surface). This feature illustrates a potential role of surface relaxation in formation of crystalline nano-size clusters of WO₃. The surface relaxation is accompanied by a dramatic redistribution of the density of states near the Fermi level, in particular a transformation of surface electronic states. This redistribution is responsible for the decrease of electronic energy and therefore is suggested to be the driving force for surface relaxation of the WO₃(0 0 1) surface and, presumably, similar surfaces of other transition metal oxides.     

High resolution analysis of the rotational levels of the (0 0 0), (0 1 0), (1 0 0), (0 0 1), (0 2 0), (1 1 0) and (0 1 1) vibrational states of SO2

A high resolution (0.0018 cm⁻¹) Fourier transform instrument has been used to record the spectrum of an enriched ³⁴S (95.3%) sample of sulfur dioxide. A thorough analysis of the ν₂, 2ν₂ − ν₂, ν₁, ν₁ + ν₂ − ν₂, ν₃, ν₂ + ν₃ − ν₂, ν₁ + ν₂ and ν₂ + ν₃ bands has been carried out leading to a large set of assigned lines. From these lines ground state combination differences were obtained and fit together with the existing microwave, millimeter, and terahertz rotational lines. An improved set of ground state rotational constants were obtained. Next, the upper state rotational levels were fit. For the (0 1 0), (1 1 0) and (0 1 1) states, a simple Watson-type Hamiltonian sufficed. However, it was necessary to include explicitly interacting terms in the Hamiltonian matrix in order to fit the rotational levels of the (0 2 0), (1 0 0) and (1 0 1) states to within their experimental accuracy. More explicitly, it was necessary to use a ΔK = 2 term to model the Fermi interaction between the (0 2 0) and (1 0 0) levels and a ΔK = 3 term to model the Coriolis interaction between the (1 0 0) and (0 0 1) levels. Precise Hamiltonian constants were derived for the (0 0 0), (0 1 0), (1 0 0), (0 0 1), (0 2 0), (1 1 0) and (0 1 1) vibrational states.