Synthesis, characterization and optical properties of water-soluble ZnS:Mn nanoparticles

ZnS nanoparticles with Mn²⁺ doping (0.5-20%) have been prepared through a simple chemical method, namely the chemical precipitation method. The structure of the nanoparticles has been analyzed using X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and UV-vis spectrometer. The size of the particles is found to be 3-5 nm range. Photoluminescence spectra were recorded for undoped ZnS nanoparticles using an excitation wavelength of 320 nm, exhibiting an emission peak centered at around 445 nm. However, from the Mn²⁺-doped samples, a yellow-orange emission from the Mn²⁺⁴T₁-⁶A₁ transition is observed along with the blue emission. The prepared Mn²⁺-doped sample shows efficient emission of yellow-orange light with the peak emission 580 nm with the blue emission suppressed. The maximum PL intensity is observed only at the excitation energy of 3.88 eV (320 nm). Increase in stabilizing time up to 48 h in de-ionized water yields the enhancement of emission intensity of doped (4% Mn²⁺) ZnS. The correlation made through the concentration of Mn²⁺ versus PL intensity resulted in opposite trend (mirror image) of blue and yellow emissions.     

Dual mode emission and harmonic generation in ZnO-CaO-Al2O3: Er nano-composite

Er³⁺ doped ZnO-CaO-Al₂O₃ nano-composite phosphor has been synthesized through combustion method and its emission and harmonic generation properties have been studied. The X-ray diffraction and thermal analysis techniques have been used to prove the dual phase (ZnO and CaO-Al₂O₃) nature of the phosphor. The phosphor has shown up-conversion emission on near-infra-red (976 nm) excitation and down-conversion emission on 355 nm excitation in presence of Er³⁺ and thus behaves as a dual mode phosphor. On excitation with 976 nm diode laser, material shows color tunability (calcination of composite material at different temperatures). Formation of ZnO nanocrystals on heat treatment of as-synthesized sample has shown its characteristic emission at 388 nm and also the energy transfer from ZnO to Er³⁺ ions. The low temperature emission measurements have been carried out and the results have been discussed. Phosphor has shown strong second harmonic generation (SHG) at 532 nm on 1064 nm and at 266 nm on 532 nm excitation.     

The influence of growth parameters on the optical properties and morphology of UHV deposited Ni thin films

Nickel films of different thickness ranging from 15 nm to 350 nm were deposited on glass substrates, at different substrate temperatures (313-600 K) under UHV condition. The nano-structure of the films was obtained, using X-ray diffraction (XRD) and atomic force microscopy (AFM). The nano-strain in these films was obtained using the Warren-Averbach method. Their optical properties were measured by spectrophotometry in the spectral range of 190-2500 nm. Kramers-Kronig method was used for the analysis of the reflectivity curves. The absorption peaks of Ni thin films at ∼1.4 eV (transition between the bands near W and K symmetry points) and ∼5.0 eV (transition from L_2^′ to L₁ upper) are observed, with an additional bump at about 2 eV. The over-layer thickness was calculated to be less than 3.0 nm, using the Transfer Matrix method. The changes in optical data are related to different phenomena, such as different crystallographic orientations of the grains in these polycrystalline films (film texture), nano-strain, and film surface roughness.     

Photophysical and nonlinear optical properties of zincphthalocyanines with peripheral substitutions

Photophysical and nonlinear optical properties of zinc phthalocyanines (ZnPc) bearing peripheral phenoxy substituents containing different functionalized groups were studied. Fluorescence spectra corresponding to the optical transition S₁ → S₀ are found to be appeared at 684 or 686.4 nm. Z-scan technique reveals large nonlinearities, where the absorptive and refractive effects are separately evaluated. Saturation absorption of ZnPc-1 was observed at 632.8 nm, with a very large nonlinear absorption coefficient β = −1.36 × 10⁻² cm/W. However a strong nonlinear refractive effect was found in all ZnPcs (1-4). Transmitted versus incident irradiance measurements carried out on ZnPc-1 and ZnPc-2, showed a very clear optical limiting behavior with irradiance thresholds around be 44 W/cm² and 90 W/cm² respectively.     

Anisotropic nonlinear optical absorption of gold nanorods in a silica matrix

Nanocomposite films consisting of gold nanospheres or gold nanorods embedded in a silica matrix have been prepared using a hybrid deposition technique consisting of plasma-enhanced chemical vapor deposition of SiO₂ and co-sputtering of gold, followed by annealing at 900 °C. Subsequent irradiation with 30 MeV heavy ions (Cu⁵⁺) was used to form gold nanorods. Linear and nonlinear optical properties of this material are closely related with the surface plasmon resonance in the visible. The nonlinear absorption coefficient (α₂@532 nm) for the films containing gold nanospheres was measured by Z-scan and P-scan techniques, and it was found to be isotropic and equal to −4.8 × 10⁻² cm/W. On the contrary, gold nanorods films exhibited two distinct surface plasmon resonance absorption bands giving rise to a strong anisotropic behavior, namely a polarization-dependent linear absorption and saturable absorption. Z-scan and P-scan measurements using various light polarization directions yielded nonlinear absorption coefficient (α₂@532 nm) values varying from −0.9 × 10⁻² cm/W up to −3.0 × 10⁻² cm/W. Linearity of the P-scan method in the context of nanocomposite saturable absorption is also discussed.     

Nonlinear optical absorption and fluorescence of phosphine-substituted bithiophenes in the violet-blue spectral region

The nonlinear optical absorptions of two 5,5′-bis(diphenylphosphino)-2,2′-bithiophene derivatives, Ph₂(X)P(C₄H₂S)₂P(X)Ph₂ (X = O, 1; S, 2), have been investigated by direct transmission measurement with both picosecond and nanosecond laser pulses from 420 nm to 480 nm. Saturated dichloromethane solutions of 1 and 2 exhibit strong nonlinear optical absorptions in this violet-blue spectral region with that of 2 being stronger at all wavelengths. In the picosecond regime, at 420 nm, the transmittance rapidly falls to 50% when the incident fluence is 0.22 J/cm² for 1 and 0.11 J/cm² for 2. Two-photon absorption appears to be the primary mechanism for this nonlinear absorption. The two-photon absorption coefficients β for 1 (2.1 cm/GW) and 2 (4.4 cm/GM) were obtained by fitting the measurement of transmittance as the function of incident beam intensity at 420 nm. These β values are comparable with some of the best results obtained for organic materials in the green, red and infrared spectral region. Both compounds also show fluorescence with an emission peak at 390 nm for 1 and 400 nm for 2. The fluorescence of 1 is considerably stronger than is that of 2. The combination of the wide band gap and strong fluorescence emission of 1 makes it a promising candidate as a host material for blue organic light emitting diodes.     

Iodine hyperfine structure and absolute frequency measurements at 565, 576, and 585 nm

The hyperfine structure splittings of the P(10)14-1, R(15)14-1, and R(99)15-1 transitions at 585 nm, P(62)17-1 at 576 nm, and P(80)21-1 at 565 nm in ¹²⁷I₂ are measured by heterodyne spectroscopy using two dye lasers. In addition, the absolute frequencies of the hyperfine components P(10)14-1 a₁₅ and P(80)21-1 a₁₀ are determined using a self-referenced frequency comb. These frequencies are used in an experiment testing relativistic time dilation by laser spectroscopy on a fast ion beam.     

Nonlinear optical properties of periodic gold nanoparticle arrays

Periodic Au nanoparticle arrays were fabricated on silica substrates using nanosphere lithography. The identical single-layer masks were prepared by self-assembly of polystyrene nanospheres with radius R = 350 nm. The structural characterization of nanosphere masks and periodic particle arrays was investigated by atomic force microscopy. The nonlinear optical properties of the Au nanoparticle arrays were determined using a single beam z-scan method at a wavelength of 532 nm with laser duration of 55 ps. The results show that periodic Au nanoparticle arrays exhibit a fast third-order nonlinear optical response with the nonlinear refractive index and nonlinear absorption coefficient being n₂ = 6.09 × 10⁻⁶ cm²/kW and β = −1.87 × 10⁻⁶ m/W, respectively.     

BaAl12O19:Mn green emitting nanophosphor for PDP application synthesized by solution combustion method and its Vacuum Ultra-Violet Photoluminescence Characteristics

Nanostructured BaAl₁₂O₁₉:Mn²⁺ phosphor particles of nano-rod morphology with diameter 40-100 nm and length up to 200-600 nm has been synthesized by solution combustion method and its photoluminescence characteristics have been studied by Vacuum Ultra-Violet Photoluminescence spectrometer (VUVPL) under 147 nm excitation. The crystallographic phase purity of BaAl₁₂O₁₉:Mn²⁺ nanostructured phosphor particle synthesized by solution combustion approach is confirmed by X-ray diffraction (XRD). The broadening of XRD diffraction peaks indicates nanocrystalline nature of particles present in powder. The emission spectrum of BaAl₁₂O₁₉:Mn²⁺ nanophosphor on 147 nm excitation consists of a wide green band with a peak at about 515 nm, which is due to a 3d⁵ (⁴T_1g)-3d⁵ (⁶A_1g) transition corresponds of Mn²⁺ ions. It is found that the concentration quenching is obtained when Mn²⁺ content (x) is 0.05 in BaAl₁₂O₁₉:xMn²⁺ nanophosphor on 147 nm excitation. The decay time of 3d⁵ (⁴T_1 g)-3d⁵ (⁶A_1 g) transition of Mn²⁺ ions at 147 nm excitation is about 23 ms for BaAl₁₂O₁₉:Mn²⁺ nanophosphor. This nanostructured green emitting BaAl₁₂O₁₉:Mn²⁺ phosphor can find potential application in Plasma Display Panels (PDPs) and mercury-free fluorescent lamps.     

Nonlinear optical absorption studies of an organo-metallic complex by Z-scan technique

An organo-metallic complex, [(CH₃)₄N][Ni(dmit)₂] (dmit²⁻ = (1,3-dithiole-2-thione-4,5-dithiolate), abbreviated as MeNi, is synthesized. The nonlinear optical absorption properties of MeNi dissolved in acetone have been studied using the open-aperture Z-scan technique with 40 ps pulse width at 1064 nm and 1 ns, 15 ns pulse width at 1053 nm, respectively. Strong saturable absorption has been found when the sample solution is irradiated by 40 ps and 1 ns laser pulses. While irradiated with 15 ns laser pulse, a stronger reverse saturable absorption has been found. The nonlinear optical absorption coefficients are −1.03 × 10⁻¹¹ m/W, −1.85 × 10⁻¹¹ m/W and 3.84 × 10⁻¹⁰ m/W, respectively. The mechanism responsible for the difference between the results is analyzed. All the results suggest that this material may be a promising candidate for the application to laser pulse compression in the near-infrared waveband.     

Synthesis and optical characterization of PVP and SHMP-encapsulated Mn-doped ZnS nanocrystals

Zinc sulfide semiconductor nanocrystals doped Mn²⁺ have been synthesized via a solution-based method utilizing optimum dopant concentration (4%) and employing polyvinyl pyrrolidone (PVP) and sodium hexametapolyphosphate (SHMP) as capping agents. UV-vis absorbance spectra for all of the synthesized nanocrystals show an exitonic peak at around 310 nm. The particle size and morphology were characterized by scanning electron microscopy (SEM), FT-IR, X-ray diffraction (XRD), transmission electron microscopy (TEM) and photoluminescence spectrum (PL). Diffraction data confirmed that the crystallite size is around 3-5 nm. Room temperature photoluminescence (PL) spectrum for the bare ZnS sample shows a strong band at ∼445 nm. The uncapped and capped(SHMP, PVP) ZnS:Mn²⁺ samples show a strong and broad band in the ∼580-585 nm range.     

Synthesis and nonlinear optical characterization of SnO2 quantum dots

The present paper demonstrates the preparation and characterization of SnO₂ semiconductor quantum dots. Extremely small ∼1.1 and ∼1.4 nm SnO₂ samples were prepared by microwave assisted technique with a frequency of 2450 MHz. Based on XRD analysis, the phase, crystal structure and purity of the SnO₂ samples are determined. UV-vis measurements showed that, for the both size of SnO₂ samples, excitonic peaks are obtained at ∼238 and ∼245 nm corresponding to ∼1.1 nm (sample 1) and ∼1.4 nm (sample 2) sizes, respectively. STM analysis showed that, the quantum dots are spherical shaped and highly monodispersed. At first, the linear absorption coefficients for two different sizes of SnO₂ quantum dots were measured by employing a CW He-Ne laser at 632.8 nm and were obtained about 1.385 and 4.175 cm⁻¹, respectively. Furthermore, the nonlinear refractive index, n₂, and nonlinear absorption coefficient, β, were measured using close and open aperture Z-scan respectively using the same laser. As quantum dots have strong absorption coefficient to obtain purely effective n₂, we divided the closed aperture transmittance by the corresponding open aperture in the same incident beam intensity. The nonlinear refraction indices of these quantum dots were measured in order of 10⁻⁷ (cm²/W) with negative sign and the nonlinear absorption coefficients were obtained for both in order of 10⁻³ (cm/W) with positive sign.     

Effect of deposition pressure on structural, optical and electrical properties of zinc selenide thin films

ZnSe thin films have been prepared by inert gas condensation method at different gas pressures. The influence of deposition pressure, on structural, optical and electrical properties of polycrystalline ZnSe films have been investigated using X-ray diffraction (XRD), optical transmission and conductivity measurements. The X-ray diffraction study reveals the sphalerite cubic structure of the ZnSe films oriented along the (1 1 1) direction. The structural parameters such as particle size [6.65-22.24 nm], strain [4.01-46.6×10⁻³ lin⁻² m⁻⁴] and dislocation density [4.762-18.57×10¹⁵ lin m⁻²] have been evaluated. Optical transmittance measurements indicate the existence of direct allowed optical transition with a corresponding energy gap in the range 2.60-3.00 eV. The dark conductivity (σ_d) and photoconductivity (σ_ph) measurements, in the temperature range 253-358 K, indicate that the conduction in these materials is through an activated process having two activation energies. σ_d and σ_ph values decrease with the decrease in the crystallite size. The values of carrier life time have been calculated and are found to decrease with the reduction in the particle size. The conduction mechanism in present samples has been explained, and the density of surface states [9.84-21.4×10¹³ cm⁻²] and impurity concentration [4.66-31.80×10¹⁹ cm⁻³] have also been calculated.     

Near-infrared emission bands of Er-doped YAP and LSO crystals

The ground state absorption (GSA), photoluminescence (PL) and photoluminescence excitation (PLE) spectra for Er(1.0 at%):YAP and Er(0.5 at%):LSO were measured at room temperature. Based on the GSA spectra, the radiative transition rates and luminescence branch ratios of erbium ions were determined by the Judd-Ofelt (J-O) method. In the range of 1400-1700 nm Er(1.0 at%):YAP has intense absorption at 1509 nm (0.96×10⁻²⁰ cm²), which is almost two times larger than the peak absorption of Er(0.5 at%):LSO. From the PL and PLE spectra, four intense emission bands around 850 nm (⁴S_3/2→⁴I_13/2), 980 nm (⁴I_11/2→⁴I_15/2), 1230 nm (⁴S_3/2→⁴I_11/2) and 1520 nm (⁴I_13/2→⁴I_15/2) were observed. The stimulated emission cross-sections of the four bands were calculated by the Fuchtbauer-Ladenberg (F-L) equation. The results suggest that Er(1.0 at%):YAP has potential to realize laser oscillation at 858 nm because of the relatively large simulated emission cross-section (1.76×10⁻²⁰ cm²). The temperature dependences of the PL spectra for the two crystals were also investigated in the range of 290-12 K. The ∼1520 nm emission presents continuous increase with temperature, while the emissions around 850, 1230 and 980 nm firstly increase with temperature, then reach their own largest values at the transition temperatures (about 100 K), and finally decrease with temperature. These results were well interpreted by the temperature dependence of multi-phonon process.     

Characterization of optical waveguide in Nd: LuVO4 crystals by triple-energy oxygen ion implantation

We report on the optical planar waveguide formation and modal characterization in Nd:LuVO₄ crystals by triple-energy O³⁺-ion implantation at energies of 2.4, 3.0, and 3.6 MeV and doses of 1.4, 1.4, and 3.1×10¹⁴ ions/cm², respectively. The prism-coupling method is used to investigate the dark-mode property at a wavelength of 633 nm. The refractive index profiles of the waveguide are reconstructed by the reflectivity calculation method (RCM). The modal analysis shows that the fields of TE modes are well restricted in the guiding region, which indicates the formation of non-leaky waveguide in the crystal.     

Growth of oxide thin films for optical gas sensor applications

Tungsten trioxide and titanium dioxide thin films were synthesised by pulsed laser deposition. We used for irradiations of oxide targets an UV KrF* (λ = 248 nm, τ_FWHM ≅ 20 ns, ν = 2 Hz) excimer laser source, at 2 J/cm² incident fluence value. The experiments were performed in low oxygen pressure. The (0 0 1) SiO₂ substrates were heated during the thin film deposition process at temperature values within the 300-500 °C range. The structure and crystalline status of the obtained oxide thin films were investigated by high resolution transmission electron microscopy. Our analyses show that the films are composed by nanoparticles with average diameters from a few to a few tens of nm. Moreover, the films deposited at substrate temperatures higher than 300 °C are crystalline. The tungsten trioxide films consist of a mixture of triclinic and monoclinic phases, while the titanium dioxide films structure corresponds to the tetragonal anatase phase. The oxide films average transmittance in the visible-infrared spectral range is higher than 80%, which makes them suitable for sensor applications.     

Experimental determination of optical constants of MgF2 and AlF3 thin films in the vacuum ultra-violet wavelength region (60-124 nm), and its application to optical designs

The investigation of some solar radiations of interest for astrophysicists requires optics in the 80-130 nm vacuum ultra-violet spectral range (VUV). In this domain, where both transmittance and reflectance of most materials are very low, the measurement of optical constants is specifically difficult, and optical data are consequently often either inexistent or uncertain. Reliable modelling of optical components for VUV, like polarizing multi-layered mirrors, necessitates prior measurement of complex indices of the thin films involved in the coating. Fluorides like MgF₂ or AlF₃ are among the rare materials capable to contribute to multi-layer mirrors in the VUV.We have determined optical constants of thin films of these two materials by using a two media reflectance method at normal incidence and a graphical determination particularly suited to this VUV region, which we presented in a previous paper. Optical constants are determined in the range 60-124 nm with 2 nm step, and are compared to existing data. On the basis of these measured indices, polarizing mirrors for λ₁ = 121.6 nm or λ₂ = 103.2 nm have been modelled and fabricated. Their reflectance measured versus incidence angle by using monochromatized synchrotron radiation at the above wavelengths is found in agreement with the calculated predictions.     

Second-harmonic generation in transparent surface crystallized GeS2-Ga2S3-CdS chalcogenide glasses

Transparent surface crystallized glasses containing CdGa₂S₄ nonlinear optical crystal were prepared by the 70GeS₂ · 15Ga₂S₃ · 15CdS (GGC15) chalcogenide glass. Average diameters of crystallites are about 150 nm and 600 nm for heating at 405 °C for 48 and 108 h (named GGC15-48 and GGC15-108), respectively, and the thickness of the surface crystallized layer was approximately 15 μm. By using the Maker fringe measurement, prominent second-harmonic generation was observed from these crystallized glasses, and the χ⁽²⁾ of the GGC15-48 sample is calculated to be as well as 38.85 pm/V, and the value is 13.7 pm/V for the GGC15-108. They are promising to be applied in photoelectric and all-optical field in the future.     

Electrical and optical properties of silver doped indium oxide thin films prepared by reactive DC magnetron sputtering

Silver doped indium oxide (In_2−x Ag_x O_3−y) thin films have been prepared on glass and silicon substrates at room temperature (300 K) by reactive DC magnetron sputtering technique using an alloy target of pure indium and silver (80: 20 atomic %. The magnetron power (and hence the metal atom sputter flux) is varied in the range 40-80 W. The energy dispersive analysis of X-ray (EDAX) results show that the silver content in the film decreases with increasing magnetron power. The grain size of these films is of the order of 100 nm. The resistivity of these films is in the range 10⁻²-10⁻³ Ω cm. The work function of the silver-indium oxide films (by Kelvin Probe) are in the range: 4.64-4.55 eV. The refractive index of these films (at 632.8 nm) varies in the range: 1.141-1.195. The optical band gap of indium oxide (3.75 eV) shrinks with silver doping. Calculations of the partial ionic charge (by Sanderson's theory) show that silver doping in indium oxide thin films enhance the ionicity.     

Effect of Nd concentration on structural and optical properties of Nd:Y2O3 transparent ceramic

Y₂O₃ transparent ceramics with different Nd concentration (0.1-7.0at%) were fabricated using ZrO₂ as additive. All the samples exhibit high transparency over a broad spectral region. The elements (Y, O and Nd) are uniformly distributed in the ceramic body, and the average grain size increases with Nd content. Based on the absorption spectrum, the Judd-Ofelt intensity parameters are calculated (Ω₂=4.364×10⁻²⁰ cm², Ω₄=3.609×10⁻²⁰ cm² and Ω₆=2.919×10⁻²⁰ cm²). The absorption coefficients increase linearly with Nd³⁺ doping concentration. The absorption cross-section at 804 nm and stimulated emission cross-section at 1078 nm are calculated to be 1.54×10⁻²⁰ and 7.24×10⁻²⁰ cm², respectively. All the emission bands exhibit the highest emission intensities with 1.0at% Nd³⁺ ion content, while the lifetime decreases dramatically from 321.5 μs (0.1at% Nd) to 17.9 μs (7.0at% Nd). According to the emission spectra and measured lifetime, the optimum doping concentration of Nd³⁺ ion in Y₂O₃ transparent ceramic might be around 1.0at%.