The preparation, properties and application of carbon fibers for SPME

The conditions of preparation of new types of carbon fibers for solid phase micro extraction (SPME) prepared by methylene chloride pyrolysis (at 600 °C) on the quartz fiber (100 μm) as well as by supporting synthetic active carbon (prepared especially for this purposes) supported in a special epoxide-acrylic polymer is described. The properties of such carbon fibers for SPME were defined by determination of the partition coefficient of the tested substances (i.e., benzene, toluene, xylenes, trichloromethane and tetrachloromethane) and by the microscopic investigations with the application of the optical and scanning electron microscope.

The obtained carbon SPME fibers were applied to the analysis of some volatile organic compounds from its aqueous matrix. During chromatographic GC test, at the investigated SPME carbon fibers, we obtained different but mostly high partition coefficients for the determined compounds (Kfs from 120 for trichloromethane up to 11,500 for tetrachloromethane).

Owing to the high partition coefficients of the studied substances obtained on carbon fibers, it was possible to do the analysis of organic substances occurring in trace amounts in different matrices. In this paper, we present the analysis of BTX contents in the petrol analyzed with the application carbonized with CH₂Cl₂ SPME fiber (C1NM) and a headspace over the petrol sample (concentration of each BTX g/dm³).     

Rapid analysis of free medium-chain fatty acids and related ethyl esters in beer using SPE and HRGC

A modification of a procedure by Hage [1] is proposed for the gas chromatographic evaluation of the content of free medium-chain fatty acids and related ethyl esters in beer. The method involves extraction of free fatty acids and ethyl esters by SPE using C₁₈ bonded phase columns, derivatization of free fatty acids and related ethyl esters with diazomethane, and GC analysis using an SP-2340 capillary column. The results obtained have shown the method to be rapid and highly reproducible. The technique has been compared with other methods used for determination of free fatty acids.     

Use of SPME extraction to determine organophosphorus pesticides adsorption phenomena in water and soil matrices

Solid-phase micro extraction (SPME) coupled with GC enables rapid and simple analysis of organophosphorus pesticides in a range of complex matrices. Investigations were made into the extraction efficiencies from water of six organophosphorus insecticides (methamidophos, omethoate, dimethoate, parathion methyl, malathion, and parathion ethyl) showing a wide range of polarities. Three SPME fibres coated with different stationary phases, polydimethylsiloxane, polyacrylate, and carbowax-divinylbenzene (CW-DVB), were investigated. Water was spiked with the pesticides at concentrations from 1 to 0.01 µg mL-1, and the solutions used for optimization of the procedure. The CW-DVB fibre, with a 65 µm coating, gave the best performance. The optimized experimental conditions were sample volume 10 mL at 20°C, equilibration time 16 min, pH 5, and presence of 10% w/v NaCl. SPME analyses were performed on solutions obtained by equilibrating aqueous pesticide solutions with six certified soils with various physico-chemical characteristics. SPME data were also assessed by comparison with analyses performed by using conventional solid-phase extraction. Results indicate the suitability of SPME for analysis of pesticides in environmental water samples.     

一种改进的SPME方法提取火场残留物中的促燃剂

对当前国内外用于火场残留物中促燃剂的提取方法进行研究,包括采用活性炭片法(ACS)、固相微萃取(SPME)以及对固相微萃取技术从传统的热解吸模式到溶剂脱附模式的扩展性思考。通过提取3种促燃剂(汽油,煤油和柴油)检材的效能比较与分析,优化了实验条件,确定了SPME的提取和溶剂脱附的方法,实验研究表明,SPME-溶剂脱附法是火场促燃剂残留物分析的有效方法之一。     

Optimisation of a simple and reliable method based on headspace solid-phase microextraction for the determination of volatile phenols in beer

A simple, accurate and sensitive method based on headspace solid-phase microextraction (HS-SPME) coupled to gas chromatography–tandem mass spectrometry (GC–MS/MS) was developed for the analysis of 4-ethylguaiacol, 4-ethylphenol, 4-vinylguaiacol and 4-vinylphenol in beer. The effect of the presence of CO₂ in the sample on the extraction of analytes was examined. The influence on extraction efficiency of different fibre coatings, of salt addition and stirring was also evaluated. Divinylbenzene/carboxen/polydimethylsiloxane was selected as extraction fibre and was used to evaluate the influence of exposure time, extraction temperature and sample volume/total volume ratio (V_s/V_t) by means of a central composite design (CCD). The optimal conditions identified were 80 °C for extraction temperature, 55 min for extraction time and 6 mL of beer (V_s/V_t 0.30). Under optimal conditions, the proposed method showed satisfactory linearity (correlation coefficients between 0.993 and 0.999), precision (between 6.3% and 9.7%) and detection limits (lower than those previously reported for volatile phenols in beers). The method was applied successfully to the analysis of beer samples. To our knowledge, this is the first time that a HS-SPME based method has been developed to determine simultaneously these four volatile phenols in beers.     

Magnetic mixed hemimicelles solid-phase extraction of xanthohumol in beer coupled with high-performance liquid chromatography determination

In this study, silica-coated magnetic nanoparticles (Fe(3)O(4)/SiO(2) NPs) modified by cetyltrimethylammonium bromide (CTAB) were synthesized. They were successfully applied for extraction of xanthohumol in beer based on magnetic mixed hemimicelles solid-phase extraction (MMHSPE) coupled with high-performance liquid chromatography-ultraviolet determination. The main factors influencing the extraction efficiency including the surfactant amount, the beer pH, the extraction time, the desorption condition and the maximum extraction beer volume were optimized. Under the optimized conditions, a concentration factor of 60 was achieved by extracting 120 mL beer sample using MMHSPE and the detection limit of xanthohumol is 0.0006 mg/L. The proposed method was successfully applied for determination of xanthohumol in various beer samples with the xanthohumol contents in the range of 0.031-0.567 mg/L. The satisfactory recoveries (90-103%) were obtained in analyzing spiked beer samples.     

Comparison and validation of calibration methods for in vivo SPME determinations using an artificial vein system

The success of in vivo solid phase microextraction (SPME) depends significantly on the selection of calibration method. Three kinetic in vivo SPME calibration methods are evaluated in this paper: (1) on-fibre standardization (OFS), (2) dominant pre-equilibrium desorption (DPED), and (3) the diffusion-based interface (DBI) model. These are compared in terms of precision, accuracy, and ease of experimental use by employing a flow device simulating an animal circulatory system. In addition, the kinetic calibration methods were validated against established SPME equilibrium extraction (EE) external calibration and a conventional sample preparation method involving protein precipitation. The comparison was performed using a hydrophilic drug fenoterol as the analyte of interest. Liquid chromatography-tandem mass spectrometry (LC-MS/MS) was used for the determinations. All three kinetic methods compared well with both EE extraction and the conventional method in terms of accuracy (93-119%). In terms of precision, the DBI model had the best precision in whole blood and buffered phosphate saline solution with %RSD similar to the standard techniques (9-15%). DPED had the poorest precision of %RSD (20-30%) possibly due to errors associated with uncertainty in the amount of standard loaded on-fibre and remaining on the fibre after desorption. In addition, incurred errors could result due to the greater number of fibres used in comparison to the other two calibration methods. The precision of the OFS procedure was better than for DPED primarily because the use of multiple fibres is eliminated. In terms of the ease of use for calibration, the DBI model was the simplest and most convenient as it did not require standards once it had been calibrated or the uptake constant was calculated. This research suggests the potential use of DBI model as the best kinetic calibration method for future in-vein blood SPME investigations.     

Detection of ethanol in human body fluids by headspace solid-phase micro extraction (SPME)/capillary gas chromatography

Summary Ethanol has been found extractable from human whole blood and urine samples by headspace solid-phase micro extraction (SPME) with a Carbowax/divinylbenzene-coated fiber. After heating a vial containing the body fluid sample with ethanol, and isobutanol as internal standard (IS) at 70°C in the presence of (NH₄)₂SO₄, a Carbowax/divinylbenzene-coated SPME fiber was exposed in the headspace of the vial to allow adsorption of the compounds. The fiber needle was then injected into a middle-bore capillary gas chromatography (GC) port. The headspace SPME-GC gave intense peaks for both compounds; a small amount of background noises appeared, but did not interfere with the detection of the compounds. Recoveries of ethanol and IS were 0.049 and 0.026% for whole blood, respectively, and 0.054 and 0.085% for urine, respectively. The calibration curves for ethanol showed excellent linearity in the range of 80–5000 mg L^–1 for whole blood and 40–5000 mg L^–1 for urine; the detection limits for both samples were 20 and 10 mg L^–1, respectively. The data on actual determination of ethanol after the drinking of beer are also presented for two subjects.     

用SPME/GC-MS方法检验涉火案件中痕量汽油残留物成分

在纵火、爆炸、凶杀等刑事案件中,经常会遇到痕量汽油残留组分的检验与认定。汽油主要由C12以前的烷烃、烯烃、环烷烃和芳香烃化合物组成。由于涉火案件现场中燃烧介质及其中所含汽油的燃烧时间和燃烧程度都不尽相同,那么残留在介质中的汽油组分多少及轻重组分相对含量会产生较     

SPME-GC-MS法分析水中的精禾草克

精禾草克,又名精喹禾灵,英文名为quizalofop-p-ethy、NC302D(+),分子式为C19H17ClN2O4,为淡褐色结晶,熔点76～77℃,沸点220℃／26.6Pa,密度1.35g／cm3,蒸气压110nPa(20℃),溶解度0.4mg／L(20℃),溶剂中溶解度(20℃)丙酮650,乙醇22,己烷5,甲苯360(g／L,20℃),pH9时半衰期20h,酸性中性介质中稳定,碱中不稳定。结构式如右所示。     

Tracing the origin of beer samples by NMR and chemometrics: Trappist beers as a case study

An NMR and chemometric analytical approach to classify beers according to their brand identity was developed within the European TRACE project (FP6‐2003‐FOOD‐2‐A, contract number: 0060942). Rochefort 8 Trappist beers (47 samples), other Trappist beers (76 samples) and non‐Trappist beers (110 samples) were analyzed by ¹H NMR spectroscopy. Selected NMR signals were measured and used to build classification models. Three different classification problems were identified, namely Trappist versus non‐Trappist, Rochefort versus Non‐Rochefort, and Rochefort 8 versus non‐Rochefort 8. In all the three cases, both a discriminant and a modeling approaches were followed, using partial least squares discriminant analysis (PLS‐DA) and soft independent modeling of class analogies (SIMCA), respectively, leading to very high classification accuracy as evaluated by external validation. Information regarding chemical composition was also obtained: Trappist beers contain a higher amount of formic and pyruvic acids and a lower amount of acetic acid and alanine with respect to non‐Trappist ones. Rochefort beers turned out to have also a higher content of propanol and isopentanol with respect to non‐Rochefort samples. Finally, Rochefort 8, shows the highest content of pyruvic acid and the lowest content of gallic, fumaric, acetic acids, adenosine, uridine, 2‐phenylethanol, GABA, and alanine.     

Determination of sulfite in beer samples using an amperometric fill and flow channel biosensor employing sulfite oxidase

A simple method is described to determine sulfite in beer samples using a fill and flow channel biosensor. A droplet of sample is placed into the inlet of a rectangular flow cell and begins to flow through the channel by capillarity. The flow is maintained and controlled by a porous outlet plug of defined porosity. In a rectangular flow cell, the sample solution flows through three consecutive zones: over a predictor electrode, an enzyme layer and a detector electrode. Together these three zones enable the differentiation between current due to sulfite and current due to other electroactive species in the sample. The predictor electrode is located upstream, and on the opposite channel wall to the enzyme layer and detector electrode, and is poised at the same potential (+0.65 V versus Ag/AgCl) as the detector electrode. On this electrode, the current contribution from all species in the sample solution that are oxidized at that potential is determined. The enzyme layer contains sulfite oxidase, which, in the process of oxidizing sulfite, produces hydrogen peroxide, which itself is reduced by excess sulfite. The current at the downstream detector electrode is therefore different from that at the predictor electrode as a result of the enzyme reaction and the difference of the currents, corrected for the dimensions of the electrodes, is proportional to the concentration of sulfite. The method enables a straightforward correction of the interfering current at the detector electrode and a determination of the analyte concentration. The effect of interferences from ascorbic acid, ethanol, sorbic acid and tartaric acid in the detection of sulfite is efficiently removed. The concentration of sulfite in a sample of beer measured by the biosensor is equivalent to that measured using a reference method based on the AOAC-recommended Monier-Williams method.     

Preparation of novel solid-phase microextraction fibers by sol-gel technology for headspace solid-phase microextraction-gas chromatographic analysis of aroma compounds in beer

3-(Trimethoxysilyl)propyl methacrylate (TMSPMA) was first used as precursor as well as selective stationary phase to prepare the sol-gel-derived TMSPMA-hydroxyl-terminated silicone oil (TMSPMA-OH-TSO) solid-phase mircroextraction (SPME) fibers for the analysis of aroma compounds in beer. TMSPMA-OH-TSO was a medium polarity coating, and was found to be very effective in carrying out simultaneous extraction of both polar alcohols and fatty acids and nonpolar esters in beer. The extraction temperature, extraction time, and ionic strength of the sample matrix were modified to allow for maximium sorption of the analytes onto the fiber. Desorption temperature and time were optimized to avoid the carryover effects. To check the matrix effects, several different matrices, including distilled water, 4% ethanol/water (v/v) solution, a concentrated synthetic beer, a "volatile-free" beer and a real beer were investigated. Matrix effects were compensated for by using 4-methyl-2-pentanol as internal standard and selecting the "volatile-free" beer as working standard. The method proposed in this study showed satisfactory linearity, precision and detection limits and accuracy. The established headspace SPME-gas chromatography (GC) method was then used for determination of volatile compounds in four beer varieties. The recoveries obtained ranged from 92.8 to 105.8%. The relative standard deviations (RSD, n = 5) for all analytes were below 10%. The major aroma contributing substances of each variety were identified via aroma indexes.     

Characterisation of absorptive sampling with SPME fibres in the EUPHORE photoreactor

The implementation of an experimental set-up for sampling, and characterisation of parameters related to absorptive sampling solid phase microextraction (SPME) in the EUPHORE photoreactor is described. Toluene was taken as probe compound. Optimisation of the sampling and calibration curves are presented. Equilibrium was achieved in just 30 s due to the good agitation in the chambers and the LOD was 0.24 ppbV. The precision was ±0.02 expressed as relative standard deviation (n = 9). The inter-fibre reproducibility was ±0.03 expressed as relative standard deviation. The effect of the temperature and the sun radiation on absorption in the fibre is also studied using a relative method to calculate the ratio K/K₀ (ratio of absorption constants at two different times during the experiment at which temperature and radiation conditions experimented important variations) calculated through known parameters, avoiding in this way the need for external calibrations in the calculation of K. The results showed a difficult to predict dependence of absorption over the combination of temperature and sun radiation and the need to develop sampling systems with absorptive SPME in which sun radiation has no influence. The stability in different conditions of compounds absorbed in the fibre was also subject to study. At room temperature half of the compound absorbed is expected to desorb in 1.21 h. Conversely, when fibres were kept at low temperatures (−86 °C) after 21 days, desorption was negligible.     

自动顶空衍生化固相微萃取法测定啤酒中的老化醛类化合物

采用邻-五氟苯甲基羟胺(PFBOA)衍生,顶空固相微萃取(HS-SPME)和气相色谱质谱(GC-MS)测定啤酒中2-甲基丁醛、3-甲基丁醛、反-2-壬烯醛等8种老化醛类化合物.顶空固相微萃取采用65 μm PDMS/DVB纤维,先用纤维吸附PFBOA溶液,再将纤维插入装有2 mL啤酒的20 mL顶空进样瓶的顶空中在60 ℃萃取60 min,衍生和萃取都在自动进样器中进行.采用GC-MS检测,特征离子为m/z 181.8种羰基化合物在0.2～500 μg/L范围内线性关系良好,相关系数在0.990以上.检测样品的相对标准偏差为1.0%～15.7%,回收率为88%～103%.同时研究并讨论了萃取纤维、萃取温度、萃取时间、样品体积等因素对醛类萃取量的影响.该方法可用于啤酒保鲜期研究和产品质量控制.     

离子色谱法同时分析啤酒中的有机酸和无机阴离子

建立了以NaOH-甲醇混合淋洗液,离子交换色谱柱,电导检测器检测,分离啤酒中有机酸和无机阴离子的离子色谱法.结果表明：在20 min内分离出啤酒中的11种主要有机酸与无机阴离子,方法回收率和相对标准偏差分别为96.30%～104.8%和0.02%～4.0%.     

Determination of sterols in biological samples by SPME with on-fiber derivatization and GC/FID

A new procedure for the determination of sterols in serum samples is proposed. The system consists of coating a Solid Phase Microextraction (SPME) microfiber in headspace mode with the derivatizing agent N,O-bis(trimethylsilyl)trifluoracetamide (BSTFA) and then applying this coated fiber to the simultaneous extraction and derivatization of three precursors in the cholesterol biosynthesis pathway (desmosterol, lathosterol and lanosterol) and two phytosterols (sitosterol and sitostanol) in serum samples. Optimization of the analytical procedure via the application of an experimental design, a study of matrix effects, and an analysis of serum pool samples are all described and discussed.     

Silica-titania sol-gel hybrid materials: synthesis, characterization and potential application in solid phase extraction

The biphenilaminepropylsilica and biphenilaminepropylsilicatitania were synthesized by sol-gel method, in two steps: (a) biphenylamine reacts with chloropropyltrimethoxysilane and (b) the product of reaction was polycondensed with tetraethylorthosilicate (TEOS) or TEOS and titanium isopropoxide. The sol-gel materials were characterized using infrared spectroscopy and N₂ adsorption-desorption isotherms and they were employed as sorbents for carcinogenic N-containing compound retention, in aqueous solution, using the SPE technique. The N-containing compounds adsorption was influenced by the titania presence and the sorption process seems to happen in the pores with higher organic density.