Effect of Interfacially Active Fractions of Some Egyptian Crude Oils on Their Emulsion Stability

Four samples from different crude oils were used for this study: light and heavy crude oils from Iran and two crude oils from Egypt, namely, Ras Gharb and Suez mix. The asphaltenes were separated from these crude oils and then the maltene (non‐asphaltenic fraction) was fractionated into waxes, aromatics, and resins. All fractions were characterized using FTIR and UV spectroscopic analyses in addition to gel permeation chromatograph (GPC). These fractions were tested for their emulsion stability. For chemometric analysis different parameters (variables) have been used to study the effect of different fractions (objects) on the emulsion stability. Such variables included the integrated areas under the stretching absorption peaks of CH in the range of 3000–2800 cm^?1, C?O in the range of 1750–1650 cm^?1, and the aromatic C?C in the range of 1650–1550 cm^?1, as well as UV absorption value at 235 nm and average molecular weight (MW). Principal component analysis (PCA) and multiple linear regression (MLR) were conducted for examining the relationship between multiple variables and the stability of water‐in‐crude oil emulsions. The results of PCA explain the interrelationships between the observations and variables in multivariate data. The correlation coefficients between different parameters derived from PCA reveals that the UV absorption value and MW are strongly correlated with emulsion stability. It also reveals that the resins, asphaltenes, and maltene have better emulsion stability than waxes and lower molecular weight aromatics. The linear relationship between the parameters and the stability of water‐in‐crude oil emulsions using MLR was modeled according to the better statistical results. The obtained mathematical model can be used to predict the stability of water‐in‐crude oil emulsions from the chemical groups and functionalities in each crude oil fraction.     

Qualitative and quantitative analysis of pyrolysis oil by gas chromatography with flame ionization detection and comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry

Pyrolysis oils have attracted a lot of interest, as they are liquid energy carriers and general sources of chemicals. In this work, gas chromatography with flame ionization detector (GC-FID) and two-dimensional gas chromatography with time-of-flight mass spectrometry (GC×GC-TOFMS) techniques were used to provide both qualitative and quantitative results of the analysis of three different pyrolysis oils. The chromatographic methods and parameters were optimized and solvent choice and separation restrictions are discussed. Pyrolysis oil samples were diluted in suitable organic solvent and were analyzed by GC×GC-TOFMS. An average of 300 compounds were detected and identified in all three samples using the ChromaToF (Leco) software. The deconvoluted spectra were compared with the NIST software library for correct matching. Group type classification was performed by use of the ChromaToF software. The quantification of 11 selected compounds was performed by means of a multiple-point external calibration curve. Afterwards, the pyrolysis oils were extracted with water, and the aqueous phase was analyzed both by GC-FID and, after proper change of solvent, by GC×GC-TOFMS. As previously, the selected compounds were quantified by both techniques, by means of multiple point external calibration curves. The parameters of the calibration curves were calculated by weighted linear regression analysis. The limit of detection, limit of quantitation and linearity range for each standard compound with each method are presented. The potency of GC×GC-TOFMS for an efficient mapping of the pyrolysis oil is undisputable, and the possibility of using it for quantification as well has been demonstrated. On the other hand, the GC-FID analysis provides reliable results that allow for a rapid screening of the pyrolysis oil. To the best of our knowledge, very few papers have been reported with quantification attempts on pyrolysis oil samples using GC×GC-TOFMS most of which make use of the internal standard method. This work provides the ground for further analysis of pyrolysis oils of diverse sources for a rational design of both their production and utilization process.     

Identification and quantification of alkene-based drilling fluids in crude oils by comprehensive two-dimensional gas chromatography with flame ionization detection

Comprehensive two-dimensional gas chromatography with flame ionization detection (GC x GC-FID) was used to measure alkene-based drilling fluids in crude oils. Compared to one-dimensional gas chromatography, GC x GC-FID is more robust for detecting alkenes due to the increased resolution afforded by second dimension separations. Using GC x GC-FID to analyze four oil samples from one reservoir contaminated with the same drilling fluid, C(15), C(16), C(17), C(18) and C(20) alkenes were identified. The drilling fluid that contaminated these samples also differed from another commercially obtained fluid, which only contained C(16) and C(18) alkenes. These results should motivate the petroleum industry to consider GC x GC-FID for measuring drilling fluids.     

Effects of pressure drop on absolute retention matching in comprehensive two-dimensional gas chromatography

Comprehensive two-dimensional gas chromatography (GC x GC) analysis has the capability to resolve many more components of complex mixtures than traditional single column GC analysis. There is an increasing need to provide reliable identification of these separated components; time-of-flight mass spectrometry (TOFMS) is the most appropriate technology to achieve this task. Rather than require MS for all GC x GC separations, it is desirable to assign peak identities to specific peak positions in the GC x GC separation space, and this necessitates matching peak retentions in the two experiments - GC x GC-FID and GC x GC-TOFMS. The atmospheric vs. vacuum outlet conditions confound this task. It is shown here that by employing a supplementary gas supply, provided to a T-union between the column outlet and the MS interface, it is possible to generate 2D chromatograms for GC x GC-FID and GC x GC-TOFMS that are essentially exactly matched. There is no degradation in separation performance or efficiency in the second column in the system interfaced to the T-union. Since the GC x GC-FID experiment uses hydrogen for maximum efficiency, and GC x GC-TOFMS uses helium carrier, translation of (conditions/retentions) must account for the different viscosities of the carrier gases. Translation of conditions is based on well-known principles established in single column analysis. Tabulated data illustrate that retention reproducibility was of the order of better than 4 s for the average first dimension retention difference, and about 40 ms for the average second dimension retention difference when comparing GC x GC-FID and GC x GC-TOFMS results. This should provide considerable support for identification in routine GC x GC-FID analysis of specific sample types, once the peaks in 2D separation space have been assigned identities through GC x GC-TOFMS analysis.     

多环芳烃指纹用于渤海采油平台原油的鉴别

采用气相色谱/质谱方法,对渤海海上4个不同区块、5个平台的6口油井原油进行了烷基化多环芳烃系列化合物和美国环保署（EPA）优先控制多环芳烃系列化合物的准确定性定量分析。通过多环芳烃原始指纹谱图、多环芳烃组分分布模式和特征比值的比较对上述原油进行鉴别。结果证明不同区块的原油中多环芳烃指纹信息不尽相同,即使在同一平台不同油井中所产的原油其指纹也存在一定差异。为确保原油鉴别的准确性,分析过程中必须在仪器的稳定性和样品前处理方面实施严格的质量控制措施。     

Identification of volatiles from pineapple (Ananas comosus L.) pulp by comprehensive two-dimensional gas chromatography and gas chromatography/mass spectrometry

Combining qualitative data from the chromatographic structure of 2-D gas chromatography with flame ionization detection (GC×GC-FID) and that from gas chromatography-mass spectrometry (GC/MS) should result in a more accurate assignment of the peak identities than the simple analysis by GC/MS, where coelution of analytes is unavoidable in highly complex samples (rendering spectra unsuitable for qualitative purposes) or for compounds in very low concentrations. Using data from GC×GC-FID combined with GC/MS can reveal coelutions that were not detected by mass spectra deconvolution software. In addition, some compounds can be identified according to the structure of the GC×GC-FID chromatogram. In this article, the volatile fractions of fresh and dehydrated pineapple pulp were evaluated. The extraction of the volatiles was performed by dynamic headspace extraction coupled to solid-phase microextraction (DHS-SPME), a technique appropriate for slurries or solid matrices. Extracted analytes were then analyzed by GC×GC-FID and GC/MS. The results obtained using both techniques were combined to improve compound identifications.     

Multidimensional Capillary GC-GC for the Analysis of Real Complex Samples. Part IV. Enantiomeric Distribution of Monoterpene Hydrocarbons and Monoterpene Alcohols of Lemon Oils

This paper describes a fully automated, multidimensional, double-oven GC-GC system, developed in our laboratory. The system is based on the use of mechanical valves which allow the multitransfer of different fractions during the same GC analysis and the use of the two GC independently when the multitransfer options is not used. Pneumatic and electronic circuits permit maintenance of constant retention times in the pre-column, even for the components eluted after numerous transfers. The system has been used for the determination of the enantiomeric distribution of β-pinene, sabinene, limonene, linalol, terpinen-4-ol, and α-terpineol in lemon oils. The results obtained allowed the characterization of cold-pressed lemon oils.     

原油中芳香硫化合物形态分布的研究

建立了原油中多环芳香硫化合物形态分布的研究方法。采用氯化钯/硅胶配位交换色谱分离原油中的芳香硫化合物,并用气相色谱/质谱分析、气相色谱-硫化学发光检测法结合色谱保留指数,鉴定出原油中的100多个多环芳香硫化物,包括含烷基取代基的苯并噻吩和二苯并噻吩类硫化物。定量分析表明,二苯并噻吩类化合物的含量占芳香硫化合物总量的91%左右。该方法可用于不同来源的原油中芳香硫化合物的形态分布研究。     

Separation and Chemical Characterization of Wetting Crude Oil Compounds

To improve the understanding of wettability, especially the influence of colloidal stability and composition of crude oil, wetting experiments on quartz sand were performed with an asphaltene-rich oil, a resin-rich oil, and with model oils containing different colloid compositions. A two-step procedure was developed to investigate the wetting behavior. In the first step those crude oil components were extracted, which preferentially wet solid surfaces. The extracted crude oil components were characterized in the second step. The amount of adsorbed oil components correlates with the stability of the crude oil colloids: low colloidal stability of crude oil leads to larger amounts of adsorbed components than does high colloidal stability. The addition of resins and/or low molecular weight asphaltenes to the crude oil stabilizes the crude oil colloids; i.e., a lower amount of wetting components are isolated by extraction in such systems. To find out, which fraction of the adsorbed oil components determines the wetting behavior of a crude oil, the wetting properties of the toluene solutions of these fractions were compared to those of the toluene solutions of the precipitated crude oil colloids. The fractions extracted with the solvent systems chloroform and methanol/chloroform showed nearly the same wetting behavior as the crude oil colloids. These fractions are characterized by the highest molecular weights, higher sulfur compositions, and the lowest H/C ratios. On the other hand, the nitrogen compounds predominate in the acetone fraction.     

Solubility Parameters Based on IR and NIR Spectra: I. Correlation to Polar Solutes and Binary Systems

IR and NIR spectra were correlated to Hildebrand and Hansen solubility parameters through use of multivariate data analysis. PLS‐1 models were developed and used to predict solubility parameters for solvents, crude oils, and SARA fractions. PLS regression showed potential for good correlation of the solubility parameters with IR and NIR spectra. Principal component analysis of IR spectra showed that crude oils are grouped according to their relative contents of heavy components such as asphaltenes. PCA of IR spectra for SARA fractions resulted in obvious groupings of the respective fractions. Prediction of solubility parameters from IR spectra of polymers, crude oils, and SARA fractions gave values that are comparable to literature values. This study indicates that correlation of solubility parameters with IR and NIR spectra is possible. In turn, it may be possible to develop models that can predict the polarities of crude oils and crude oil fractions such as resins and asphaltenes.     

原油非烃化合物结构与含量的馏分分离及联用色谱信息获取通用方法

用正己烷将沥青质从油样中分离,再根据类组分之间极性差别,用中性氧化铝-硅胶双层析柱将原油样其余部分分成脂肪烃、芳香烃和7个非烃馏分。各馏分回收完全。用色-质联用技术,将非烃馏分再分离并获取实验数据,为原油非烃结构和含量测定奠定有关的信息基础。不同油井样品研究和重复实验表明,方法对各种原油非烃化合物分离和信息测定有很好的重现性。     

大气有机物热脱附-全二维气相色谱-火焰离子化分析方法

全二维气相色谱（GC×GC）是20世纪90年代发展起来的具有高分辨率、高灵敏度、高峰容量等优势的分离技术,在我国将其用于大气挥发性有机物（VOCs）研究方面才刚刚起步.本文将GC-GC与氢火焰离子化检测器（FID）联用,构建了用于测量大气有机物的热脱附-全二维气相色谱-氢火焰离子化分析系统（TD-GC×GC-FID）.采用HP-5MS和HP-INNOWAX色谱柱,建立了C5-C15大气有机物分析方法,实现了一次分析过程同时分离非甲烷烃（NMHCs）、含氧挥发性有机物（OVOCs）和卤代烃等多种组分.利用标准物质和四级杆质谱（qMS）进行定性,外标法结合FID质量校正因子定量.目标物在GC-GC谱图中第一和第二维保留时间变化分别小于0.6s和0.02s,峰体积平均相对标准偏差为14.3%,其中烷烃和芳香烃为4.5%.标准曲线r2均值大于0.99,平均检出限为6.04ng,平均回收率为111%.利用该方法检测到2010年1月北京市区大气中400多种有机物（信噪比大于50）,鉴定了其中的103种物质,包括烷烃、烯烃、芳香烃、卤代烃、醛、酮、酯、醇和醚等.所测定有机物平均总浓度为51.3×10-9V/V,其中OVOCs约占51%,芳香烃约占30%,烷烃约占15%,卤代烃和烯烃分别占3%和1%.平均浓度最高的前3个组分是乙醇（9.84×10-9V/V）、丙酮（6.72×10-9V/V）和甲苯（3.48×10-9V/V）.     

Characterisation of lavender essential oils by using gas chromatography-mass spectrometry with correlation of linear retention indices and comparison with comprehensive two-dimensional gas chromatography

Nine samples of lavender essential oil were analysed by GC–MS using low-polarity and polar capillary columns. Linear retention indices (LRI) were calculated for each component detected. Characterisation of the individual components making up the oils was performed with the use of an mass spectrometry (MS) library developed in-house. The MS library was designed to incorporate the chromatographic data in the form of linear retention indices. The MS search routine used linear retention indices as a post-search filter and identification of the “unknowns” was made more reliable as this approach provided two independent parameters on which the identification was based. Around 70% of the total number of components in each sample were reliably characterised. A total of 85 components were identified. Semi-quantitative analysis of the same nine samples was performed by gas chromatography (GC) with flame ionisation detection (FID). The identified components accounted for more than 95% of each oil. By comparing the GC–MS results with the results from the GC×GC–FID analysis of a lavender essential oil, many more components could be found within the two-dimensional separation space.     

Identification of structures of nitrogen-containing compounds in crude oils in conjunction with chemometric resolution

A universal method was established for the systematically structural identification of nitrogen-containing compounds in crude oils. Pre-fractionation of the non-hydrocarbons in a crude oil sample into 7 fractions was performed by di-adsorption column chromatography using neutral aluminum oxide and silica gel; subsequent high-resolution separation of individual components was achieved by using capillary column gas chromatography, and compound types were detected by mass spectrometer. The two-dimensional data from the compounds in the fractions were further resolved by a chemometric method to obtained the deconvoluted chromatogram and mass spectrum of every compound, and then, the nitrogen-containing compounds were identified in combination with the retention indices. This method could relieve the difficulty of classical analysis in identifying those species with very low contents or incompletely separation, particularly in the cases where the authentic standards were not available for addition into the unknown samples in order to reveal what indeed existed in them. The structures of 168 nitrogen-containing compounds in a crude oil sample were determined by this method with satisfactory results.     

碳稳定同位素比质谱法对中东原油的鉴别

采用气相色谱/稳定同位素比质谱法(GC/IRMS)对具有相似化学特征的科威特、阿联酋、沙特以及伊拉克产的原油中正构烷烃(n-C10～n-C24)的碳稳定同位素比δ(13C/12C)进行了分析,通过原油单体烃分布趋势对比、主成分归类、同位素比值与诊断比例(Diagnostic ratio,DR)联用等方法对4种原油进行了鉴别。结果表明,沙特与伊拉克所产原油、科威特与阿联酋所产原油的单体烃分布趋势相似,且主成分相近,采用同位素比值与诊断比例联用法成功地对它们进行溯源。结果表明,沙特与伊拉克所产原油的δ(13C/12C)值以及DR(n-C17/pristane(Pr)、n-C18/phytane(Ph)、Pr/Ph)相近,说明它们具有相同的母质类型及沉积环境,属于同一种原油;科威特与阿联酋所产原油的δ(13C/12C)值相似,而DR明显不同,表明其母质类型及成熟度不同,属于不同种原油。本研究所采用的分析技术也适用于其它原油的溯源研究。     

结合直观推导式演进特征投影法分析原油中非烃结构和含量

提出一种分析原油非烃结构和含量的方法。用直观推导式演进特征投影法分辨有关二维数据以获得非烃的纯色谱和纯质谱,再将所获质谱在标准质谱库中检索,并结合色谱保留指数分析等来进行单个非烃化合物结构鉴定;利用实验数据,根据分辨获得的纯色谱峰面积所建立的规一化模型,进行非烃化合物定量分析。用本法确定了一原油样品中168个含氮化合物和该油样一个馏分中60个其它非烃化合物的结构和含量。本方法具有系统分析原油非烃结构和含量的通用性;标准化合物加标回收实验表明,其准确度很好。     

Analysis of the chemical composition of the essential oil of Polygonum minus Huds. using two-dimensional gas chromatography-time-of-flight mass spectrometry (GC-TOF MS)

The essential oil in leaves of Polygonum minus Huds., a local aromatic plant, were identified by a pipeline of gas chromatography (GC) techniques coupled with mass-spectrometry (MS), flame ionization detector (FID) and two dimensional gas chromatography time of flight mass spectrometry (GC x GC-TOF MS). A total of 48 compounds with a good match and high probability values were identified using this technique. Meanwhile, 42 compounds were successfully identified in this study using GC-MS, a significantly larger number than in previous studies. GC-FID was used in determining the retention indices of chemical components in P. minus essential oil. The result also showed the efficiency and reliability were greatly improved when chemometric methods and retention indices were used in identification and quantification of chemical components in plant essential oil.     

Evaluation of the chemical composition of Brazilian commercial Cymbopogon citratus (D.C.) stapf samples

The concentration and the chemical composition of the essential oils obtained from different samples of Cymbopogon citratus were evaluated. Among the 12 samples investigated (11 dried leaf samples and fresh plant leaves), seven presented essential oil concentrations within the threshold established by the Brazilian legislation. The moisture content was also determined and the majority of the samples presented humidity contents near 12%. The GC and GC/MS analyses of the essential oils led to identification of 22 compounds, with neral and geranial as the two major components. The total percentage of these two compounds varied within the investigated sample oils from 40.7% to 75.4%. In addition, a considerable variation in the chemical composition of the analyzed samples was observed. The process of grinding the leaves significantly decreased (by up to 68%) the essential oil content, as well as the percentage of myrcene in the oils.     

Chemotaxonomy of aromatic plants of the genus <Emphasis Type="Italic">Origanum</Emphasis> via vibrational spectroscopy

Fourier transformed-Raman (FT-Raman) and attenuated total reflection-infrared (ATR-IR) spectra of essential oils obtained from marjoram and oregano plants by hydrodistillation are presented. It is shown that the main components of the essential oils can be ascertained through both of these complementary techniques, using spectral information from the pure terpenoids. Spectroscopic analysis is based on the characteristic key bands of the individual volatile substances and therefore, in principle, these techniques allow us to discriminate between different essential oil profiles from individual oil plants of the same species (chemotypes). The combination of vibrational spectroscopy and hierarchical cluster analysis provides a fast, easy and reliable method for chemotaxonomy characterisation. The spectroscopic data presented here correlate very well with those found by gas chromatography (GC) analysis.     

Combustion characteristics and kinetic analysis of Turkish crude oils and their SARA fractions by DSC

In this study, two Turkish crude oils from southeastern part of Turkey and their saturate, aromatic, resin fractions were analyzed by differential scanning calorimetry (DSC). The experiments were performed at three different heating rates (5, 10, 15 °C min^?1) under air atmosphere. Two different reaction regions were observed from DSC curves due to the oxidative degradation of crude oil components. In the first reaction region, it was deduced that the free moisture, volatile hydrocarbons were evaporated from the crude oils, light hydrocarbons were burned, and fuel was formed. The second reaction region was the main combustion region where the fuel was burned. From DSC curves, it was observed that as the sample got heavier, the heat of the reaction increased. Saturates gave minimum heat of reaction. As the heating rate increased, shift of peak temperatures to high values and extended reaction region intervals were observed. The kinetic analysis of the crude oils and their fractions were also performed using ASTM E-698 and Borchardt and Daniels methods, respectively. Activation energy values of the crude oil samples and the fractions’ high-temperature oxidation region were close to each other and varied between 67 and 133 kJ mol^?1 in ASTM and 35 and 154 kJ mol^?1 in Borchardt and Daniels methods, respectively.