首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
Ding Y  Garcia CD 《Electrophoresis》2006,27(24):5119-5127
In this paper, we describe the separation and detection of six phenolic acids using an electrophoretic microchip with pulsed amperometric detection (PAD). The selected phenolic acids are particularly important because of their biological activity. The analysis of these compounds is typically performed by chromatography or standard CE coupled with a wide variety of detection modes. However, these methods are slow, labor intensive, involve a multistep solvent extraction, require skilled personnel, or use bulky and expensive instrumentation. In contrast, microchip CE offers the possibility of performing simpler, less expensive, and faster analysis. In addition, integrated devices can be custom-fabricated and incorporated with portable computers to perform on-site analysis. In the present report, the effect of the separation potential, buffer pH and composition, injection time and PAD parameters were studied in an effort to optimize both the separation and detection of these phenolic acids. Using the optimized conditions, the analysis can be performed in less than 3 min, with detection limits ranging from 0.73 microM (0.10 microg/mL) for 4-hydroxyphenylacetic acid to 2.12 microM (0.29 microg/mL) for salicylic acid. In order to demonstrate the capabilities of the device, the degradation of a mixture of these acids by two aquatic plants was followed using the optimized conditions.  相似文献   

2.
Ultra-rapid analysis of nitrate and nitrite by capillary electrophoresis   总被引:3,自引:0,他引:3  
Rapid analysis of nitrate and nitrite by capillary electrophoresis (CE) has been limited by the ions' very similar electrophoretic mobilities. With a pKa of 3.15, the mobility of nitrite can be selectively reduced using a low pH buffer in CE. A much shorter capillary can be used and separation voltages can be increased. With this method, nitrate and nitrite are separated in just over 10 s. This is roughly 20 times faster than current separation methods. Direct UV detection at 214 nm was employed and offered sub microM detection limits. Total analysis time (pre-rinse, injection, and separation) was less than 1 min, making this method ideal for high-throughput analysis.  相似文献   

3.
A unique integrated separation-based fiber-optic sensor for remote analysis, that incorporates capillary electrophoresis (CE) directly at the fiber sensing terminus is described for the first time. Based on laser-induced fluorescence detection, the sensor offers the potential for high sensitivity. Although the broad-band nature of fluorescence spectra limits selectivity, the high separation power of CE provides a unique dimension of selectivity, while permitting a design of diminutive size. Previously reported fluorescence-based sensors that utilize a chemical reagent phase to impart selectivity tend to be inflexible (not readily adaptable to the detection of different species) and "one-measurement-only" sensors. Conversely, the CE-based fiber-optic sensor described here is both versatile and reusable. The analysis speed and the potential for remote control are further attributes which make the system amenable to remote sensing. A "single-fiber" optical detection arrangement and a "single-reservoir" CE system with the fiber-optic probing the outlet of the separation capillary are employed. A preliminary evaluation of the separation characteristics of this CE-based sensor is presented. Highlights include an observed separation efficiency of up to 3000 theoretical plates (8 cm separation capillary) and migration time reproducibility of less than 10% for frontal mode CE separations. The potential utility of the sensor for remote analysis is demonstrated with separations involving the CE analysis of charged fluorescent dyes, CE analysis of metal complexes based on in situ complexation and micellar electrokinetic capillary chromatographic analysis of neutral fluorescent compounds.  相似文献   

4.
A high-throughput method is described for the analysis of D-serine and other neurotransmitters in tissue homogenates. Analysis is performed by microdialysis-capillary electrophoresis (CE) with laser-induced fluorescence (LIF) detection in a sheath flow detection cell. Sample pretreatment is not required as microdialysis sampling excludes proteins and cell fragments. Primary amines are derivatized on-line with o-phthaldialdehyde (OPA) in the presence of beta-mercaptoethanol followed by on-line CE-LIF analysis. Under the separation conditions described here, D-serine is resolved from L-serine and other primary amines commonly found in biological samples. Each separation requires less than 22 s. Eliminating the need for sample pretreatment and performing the high-speed CE analysis on-line significantly reduces the time required for D-serine analysis when compared with traditional methods. This method has been used to quantify D-serine levels in larval tiger salamander retinal homogenates, as well as dopamine, gamma-amino-n-butyric acid (GABA), glutamate and L-aspartate. D-serine release from an intact retina was also detected.  相似文献   

5.
CE on microchip is an emerging separation technique that has attracted wide attention and gained considerable popularity. Because of miniaturization of the separation format, CE on chip typically offers shorter analysis time and lower reagent consumption with potential development of portable analytical instrumentation. This review with 143 references is focused on proteins and peptides analysis, DNA separation including fragment sizing, genotyping, mutation detection and sequencing, and also the analysis of low-molecular-weight compounds, namely explosive residues and warfare agents, pharmaceuticals and drugs of abuse, and various small molecules in body fluids.  相似文献   

6.
Woods LA  Roddy TP  Ewing AG 《Electrophoresis》2004,25(9):1181-1187
Capillary electrophoresis (CE) has been established as powerful tool for single cell analysis. Newly developed sampling, separation and detection methods have allowed the investigation of single mammalian cells with CE despite their small size and complex composition. Advances in sample injection techniques include several novel methods for the injection of whole cells and sampling techniques for the study of cellular secretion. CE of single mammalian cells has been applied in a wide range of fields including protein analysis, neuroscience, and oncology. The development of new detection schemes in the analysis of single mammalian cells with CE has included studies of protein expression and the utilization of mass spectrometric and electrochemical detection. Subcellular mammalian cell analysis with CE also has been investigated.  相似文献   

7.
Capillary electrophoresis (CE) is a small-volume separation approach amenable to the analysis of complex samples for their small molecule, peptide and protein content. A number of the features of CE make it a method of choice for addressing questions related to neurochemistry. The figures of merit inherent to CE that make it well suited for studying cell-to-cell and intracellular signaling include small sample volumes, high separation efficiency, the ability for online analyte concentration, and compatibility with sensitive and high-information content detection methods. A variety of instrumental aspects are detailed, including detection methods and sampling techniques that are particularly useful for the analysis of signaling molecules. Studies that have used these techniques to increase our understanding of neurobiology are emphasized throughout. One notable application is single neuron chemical analysis, a research area that has been greatly advanced by CE.  相似文献   

8.
Naphthalene-2,3-dicarboxyaldehyde (NDA) is commonly used for detection of primary amines in conjunction with their separation with HPLC and CE. The fluorescence of the derivatives can be measured by a conventional fluorometer or via LIF. NDA is a reactive dye, which can replace o-phthaldehyde (OPA) and provides for derivatives which are considerably more stable than OPA derivatives. In addition, NDA can be used to derivatize primary amines at concentrations as low as 100 pM. In this work, HPLC/fluorescence and MEKC/LIF experiments were performed to separate/detect six neuroactive compounds, the amino acids, Gly, Glu, Asp, gamma-aminobutyric acid (GABA) and the catecholamines, dopamine and noradrenaline. The two methods were compared in terms of performance of separation. The amino acids can be separated in HPLC in less than 30 min and an identical separation is obtained in CE using MEKC and lithium salts with greater resolution (the number of theoretical plates was approximately 5000 for HPLC and 200 000 for MEKC). The lowest detected concentration was in the range of 0.1 nM for CE/LIF. The presence of a high salt concentration does not affect the separation of the samples. Examples of the analysis of microdialysate samples as well as amino acids in Ringer's solution are presented.  相似文献   

9.
A solid-phase microextraction (SPME) and gas chromatography-mass spectrometry (GC-MS) sampling and analysis method was developed for bis(diisopropylaminoethyl)disulfide (a degradation product of the nerve agent VX) in soil. A 30-min sampling time with a polydimethylsiloxane-coated fiber and high temperature alkaline hydrolysis allowed detection with 1.0 microg of VX spiked per g of agricultural soil. The method was successfully used in the field with portable GC-MS instrumentation. This method is relatively rapid (less than 1 h), avoids the use of complex preparation steps, and enhances analyst safety through limited use of solvents and decontamination of the soil before sampling.  相似文献   

10.
The nerve agents belong among the most toxic compounds produced by human kind. While they have been used very sporadically until now, typically in local conflicts or by local terrorists groups, the global increase in terrorist activity in the recent years has generated tremendous demand for innovative tools capable of detecting nerve agents. Fast, sensitive and reliable detection of nerve agents in the field is very important issue in present days. Capillary electrophoresis (CE) offers great possibilities for sensitive detection of these harmful compounds as well as incorporation in mobile laboratory and it proved to have capability to detect nerve agent breakdown products in real environmental samples. Laboratory-on-a-chip format offers great possibilities to create portable, field deployable, rapidly responding and potentially disposable device, allowing security forces to make the important decision regarding the safety of civilians. This article overviews the conventional capillary electrophoretic and laboratory-on-a-chip techniques for analysis of degradation products of G-type and V-type nerve agents. It discusses diverse strategies of detection of different nerve agents breakdown products, which are corresponding to their parental nerve agents. It also overviews possibilities and challenges for analysis of the real samples.  相似文献   

11.
Novel CE methods have been developed on portable instrumentation adapted to accommodate a capacitively coupled contactless conductivity detector for the separation and sensitive detection of inorganic anions and cations in post‐blast explosive residues from homemade inorganic explosive devices. The methods presented combine sensitivity and speed of analysis for the wide range of inorganic ions used in this study. Separate methods were employed for the separation of anions and cations. The anion separation method utilised a low conductivity 70 mM Tris/70 mM CHES aqueous electrolyte (pH 8.6) with a 90 cm capillary coated with hexadimethrine bromide to reverse the EOF. Fifteen anions could be baseline separated in 7 min with detection limits in the range 27–240 μg/L. A selection of ten anions deemed most important in this application could be separated in 45 s on a shorter capillary (30.6 cm) using the same electrolyte. The cation separation method was performed on a 73 cm length of fused‐silica capillary using an electrolyte system composed of 10 mM histidine and 50 mM acetic acid, at pH 4.2. The addition of the complexants, 1 mM hydroxyisobutyric acid and 0.7 mM 18‐crown‐6 ether, enhanced selectivity and allowed the separation of eleven inorganic cations in under 7 min with detection limits in the range 31–240 μg/L. The developed methods were successfully field tested on post‐blast residues obtained from the controlled detonation of homemade explosive devices. Results were verified using ion chromatographic analyses of the same samples.  相似文献   

12.
A nonaqueous CE system for separation and detection of novel electron-dopable molecular wires based on p-phenylene-bis-4,4'-(1-aryl-2,6-diphenylpyridinium) oligomers is described. The method is based on the coupling of CE separation in pure organic solvent, DMF with 50 mM acetic acid, and UV detection at 338 nm. The system offers a rapid measurement in less than 20 min for two priority nanowires and their impurities. Calibration data confirmed linear response for all compounds of interest in the concentration range 0.1-1.0 mg/mL. A highly stable response was observed for repetitive injections (RSD < or = 2.8%, n = 10).  相似文献   

13.
An experimental setup is presented here for the automated analysis of microsamples, based on the on-line coupling of a capillary SPE module and a CE unit using a two-position six-port valve, an open-closed valve to isolate electrically the sample preparation from the CE unit and a "T" interface. A C18 trapping microcolumn (dimensions 2.5 cm x 100 microm id x 360 microm od) was used for the SPE step. The utility of the proposed experimental setup was demonstrated by applying it to the determination of quinolone antibiotics in serum microsamples, which was efficiently carried out in less than 20 min (4 min for protein denaturation and 15 min for analytes preconcentration and CE-UV separation-determination). A complete optimization study was performed for preconcentration and cleanup of quinolones, the coupling of sample preparation module to the CE unit and electrophoretic separation of quinolones. A preconcentration factor of 10.4 was achieved. The volume injected with the proposed method was 125 nL versus 160 nL introduced by hydrodynamic injection. The volume required for the analysis was 2 microL, which makes the proposed experimental setup very useful for the analysis of microsamples in fields of current interest such as metabolomics or proteomics.  相似文献   

14.
With fast separation times (seconds to minutes), minimal sample requirements (nanoliters to femtoliters), and excellent mass detection limits (femtomole to zeptomole), capillary electrophoresis (CE) is ideally suited for in vitro and in vivo sampling of neurological samples with a high degree of spatial resolution. Advances in extracellular fluid analysis employing improved microdialysis and push–pull perfusion sampling methodologies has enabled the resolution of neurotransmitters present in limited amounts using CE. Great progress has been made to resolve complex neuropeptides, amino acids, and biogenic amines in tissue and cell cultures. Finally, owing largely to the small volume sampling abilities of CE, investigations of single nerve cells, both invertebrate and mammalian, have been accomplished. These applications of CE to the advancement of neuroscience are presented.  相似文献   

15.
The development of efficient and sensitive analytical methods for the separation, identification and quantification of complex biological samples is continuously a topic of high interest in biological science. In the present study, the possibility of using a polyether ether ketone (PEEK) capillary for the CE separation of peptides, proteins and other biological samples was examined. The performance of the tubing was compared with that of traditional silica capillaries. The CE analysis was performed using contactless conductivity detection (C4D), which eliminated any need for the detection window and was suitable for the detection of optically inactive compounds. In the PEEK capillary the cathodic EOF was low and of excellent stability even at extremes pH. In view of this fast biological anions were analyzed using an opposite end injection technique without compromising separation. A comparison of the performances of fused‐silica and polymer capillaries during the separation of model sample mixtures demonstrated the efficiency and separation resolution of the latter to be higher and the reproducibility of the migration times and peak areas is better. Furthermore, PEEK capillaries allowed using simple experimental conditions without any complicated modification of the capillary surface or use of an intricate buffer composition. The PEEK capillaries are considered as an attractive alternative to the traditional fused‐silica capillaries and may be used for the analysis of complex biological mixtures as well as for developing portable devices.  相似文献   

16.
This paper reports, for the first, the fast and simultaneous detection of prominent heavy metals, including: lead, cadmium and copper using microchip CE with electrochemical detection. The direct amperometric detection mode for microchip CE was successfully applied to these heavy metal ions. The influences of separation voltage, detection potential, as well as the concentration and pH value of the running buffer on the response of the detector were carefully assayed and optimized. The results clearly show that reliable analysis for lead, cadmium, and copper by the degree of electrophoretic separation occurs in less than 3min using a MES buffer (pH 7.0, 25mM) and l-histidine, with 1.2kV separation voltage and -0.8V detection potential. The detection limits for Pb(2+), Cd(2+), and Cu(2+) were 1.74, 0.73 and 0.13microM (S/N=3). The %R.S.D. of each peak current was <6% and migration times <2% for prolonged operation. To demonstrate the potential and future role of microchip CE, analytical possibilities and a new route in the raw sample analysis were presented. The results obtained allow the proposed microchip CE-ED acts as an alternative approach for metal analysis in foods.  相似文献   

17.
Borowsky J  Collins GE 《The Analyst》2007,132(10):958-962
The ability to separate complex mixtures of analytes has made capillary electrophoresis (CE) a powerful analytical tool since its modern configuration was first introduced over 25 years ago. The technique found new utility with its application to the microfluidics based lab-on-a-chip platform (i.e., microchip), which resulted in ever smaller footprints, sample volumes, and analysis times. These features, coupled with the technique's potential for portability, have prompted recent interest in the development of novel analyzers for chemical and biological threat agents. This article will comment on three main areas of microchip CE as applied to the separation and detection of threat agents: detection techniques and their corresponding limits of detection, sampling protocol and preparation time, and system portability. These three areas typify the broad utility of lab-on-a-chip for meeting critical, present-day security, in addition to illustrating areas wherein advances are necessary.  相似文献   

18.
A simple, rapid method using CE and microchip electrophoresis with C4D has been developed for the separation of four nonsteroidal anti-inflammatory drugs (NSAIDs) in the environmental sample. The investigated compounds were ibuprofen (IB), ketoprofen (KET), acetylsalicylic acid (ASA), and diclofenac sodium (DIC). In the present study, we applied for the first time microchip electrophoresis with C4D detection to the separation and detection of ASA, IB, DIC, and KET in the wastewater matrix. Under optimum conditions, the four NSAIDs compounds could be well separated in less than 1 min in a BGE composed of 20 mM His/15 mM Tris, pH 8.6, 2 mM hydroxypropyl-beta-cyclodextrin, and 10% methanol (v/v) at a separation voltage of 1000–1200 V. The proposed method showed excellent repeatability, good sensitivity (LODs ranging between 0.156 and 0.6 mg/L), low cost, high sample throughputs, portable instrumentation for mobile deployment, and extremely lower reagent and sample consumption. The developed method was applied to the analysis of pharmaceuticals in wastewater samples with satisfactory recoveries ranging from 62.5% to 118%.  相似文献   

19.
We present a method for simultaneous determination of the aminopolycarboxylic acids DTPA, EDTA and NTA in dishwashing detergents, paper mill waters, and natural waters by capillary electrophoresis (CE). The complexing agents were examined as their copper(II) complexes and separated by conventional CE with reversed polarity of the applied voltage. The optimum separation conditions were established by varying the pH and phosphate and tetradecyltrimethylammonium bromide (TTAB) concentrations in the run buffer. The separations were carried out in a fused-silica capillary (61 cm×75 m i.d.) filled with phosphate buffer (80 mmol L–1, TTAB concentration 0.5 mmol L–1, pH 7.1, voltage –20 kV) using direct UV detection at 191 and 254 nm. With this CE method all the peaks in the electropherograms were properly separated, the calibration plots gave good correlation coefficients and all three complexing agents could be detected in less than 4 min. Linear calibration plots were obtained for CuDTPA, CuEDTA and CuNTA; limits of detection were 0.03 mmol L–1 for all complexing agents and recoveries for all tested samples were within the range 104±7%. Results obtained from dishwashing detergent samples were found to be reliable and comparable with those from HPLC (R2=0.989) and UV–Vis (R2=0.985) methods.  相似文献   

20.
CE methods have been developed for the analysis of organic and peroxide-based explosives. These methods have been developed for deployment on portable, in-field instrumentation for rapid screening. Both classes of compounds are neutral and were separated using micellar electrokinetic chromatography (MEKC). The effects of sample composition, separation temperature, and background electrolyte composition were investigated. The optimised separation conditions (25 mM sodium tetraborate, 75 mM sodium dodecyl sulfate at 25 °C, detection at 200 nm) were applied to the separation of 25 organic explosives in 17 min, with very high efficiency (typically greater than 300,000 plates m−1) and high sensitivity (LOD typically less than 0.5 mg L−1; around 1–1.5 μM). A MEKC method was also developed for peroxide-based explosives (10 mM sodium tetraborate, 100 mM sodium dodecyl sulfate at 25 °C, detection at 200 nm). UV detection provided LODs between 5.5 and 45.0 mg L−1 (or 31.2–304 μM), which is comparable to results achieved using liquid chromatography. Importantly, no sample pre-treatment or post-column reaction was necessary and the peroxide-based explosives were not decomposed to hydrogen peroxide. Both MEKC methods have been applied to pre-blast analysis and for the detection of post-blast residues recovered from controlled, small scale detonations of organic and peroxide-based explosive devices.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号