两相催化体系中α，β－不饱和醛的选择性加氢反应研究Ⅰ．水溶性钌－膦配合物催化肉桂醛的加氢性能

本文研究了两种水溶性钌－膦配合物ＲｕＣｌ_２（ＴＰＰＴＳ）_３和Ｒｕｃｌ_２（ＣＯ）_２（ＴＰＰＴＳ）_２［ＴＰＰＴＳ为：Ｐ（ｍ－Ｃ_６Ｈ_４ＳＯ_３Ｎａ）_３］的合成，在水相和有机相组成的两相催化体系中，考察了它们衍生出的活性物种和以ＲｕＣｌ３－ＴＰＰＴＳ原位合成的活性物种对肉桂醛的选择加氢性能，并对反应温度（２０—８０℃），氢压（２—６ＭＰａ），催化剂浓度（１．１２×１０~（－３）～４．５０×１０~（－３）ｍｏｌ／Ｌ），配体ＴＰＰＴＳ浓度（９．０×１０~（－３）～５．４×１０~（－２）ｍｏｌ／Ｌ），表面活性剂浓度和反应时间的变化对选择加氢反应的影响进行了详细研究。实验结果表明，ＲｕＣｌ_３－ＴＰＰＴＳ原位合成配合物的催化加氢活性最高，而在金属Ｒｕ上羰基的配位将使加氢活性降低，表面活性剂ＣＴＡＢ是有效的促进剂，它的加入可大大提高加氢活性，选择适当的ＣＴＡＢ浓度，在反应结束后水相与有机相分层迅速，有利于Ｒｕ催化剂的分离，在所考察的反应条件下，肉桂醛选择加氢生成肉桂醇的转化率大于８０％，选择性达９６％以上。     

两相体系中钌膦配合物催化4—苯基—3—丁烯—2—酮加氢反应的研究

研究了水和有机物组成的两相催化体系中,由ＲｕＣｌ３－ＴＰＰＴＳ（ＴＰＰＴＳ：Ｐ（ｍ－Ｃ６Ｈ４ＳＯ３Ｎａ）３）原位反应生成的催化活性物种对４－苯基－３－丁烯－２－酮（又名苄叉丙酮）的催化加氢反应．考察了钌浓度（１．０×１０－３～６．０×１０－３ｍｏｌ／Ｌ）、氢压（１．０～６．０ＭＰａ）、反应温度（３０～７０℃）、配体浓度（１．２～７．２×１０－２ｍｏｌ／Ｌ）、阳离子表面活性剂（ＣＴＡＢ：十六烷基三甲基溴化铵）及反应时间等对加氢反应活性和选择性的影响,并与以配合物ＲｕＣｌ２（ＴＰＰＴＳ）３为催化剂前体生成的催化活性物种对加氢反应的活性及选择性进行了比较．结果表明,分别由配合物ＲｕＣｌ２（ＴＰＰＴＳ）３及ＲｕＣｌ３－ＴＰＰＴＳ原位反应生成的催化活性物种,都只催化４－苯基－３－丁烯－２－酮的Ｃ＝Ｃ键选择加氢．由配合物ＲｕＣｌ２（ＴＰＰＴＳ）３形成的催化体系的加氢活性及选择性均优于ＲｕＣｌ３－ＴＰＰＴＳ原位反应生成的催化活性物种．阳离子表面活性剂的加入,使加氢反应活性下降,选择性略有提高     

水溶性钯－膦配合物催化1－己烯加氢反应研究

研究了水溶性钯－膦配合物ＰｄＣｌ２（ＴＰＰＴＳ）２催化１－己烯加氢反应，考察了两相催化体系中添加表面活性剂ＣＴＡＢ，膦配体ＴＰＰＴＳ，以及溶液ｐＨ值等对反应的影响，证明了１－己烯加氢反应中有一诱导期．反应中涉及两种催化活性物种．一种是由ＰｄＣｌ２（ＴＰＰＴＳ）２还原生成的低氧化态催化物种，它在一定的ＣＴＡＢ浓度下，可以保持相当的稳定性．另一种是被ＴＰＰＴＳ或Ｈ２还原形成的钯黑．根据ＰｄＣｌ２和ＴＰＰＴＳ反应过程的３１ＰＮＭＲ研究，对ＰｄＣｌ２（ＴＰＰＴＳ）２分子中Ｐｄ被还原和ＴＰＰＴＳ被氧化提出了解释     

水溶性钯—膦配合物催化1—己烯加氢反应研究

研究了水溶性钯－膦配合物ＰｄＣｌ２（ＴＰＰＴＳ）２催化１－己烯加氢反应，考察了两相催化体系中添加表面活性剂ＣＴＡＢ，膦配体ＴＰＰＴＳ，以及溶液ＰＨ值等对反应的影响。证明了１－己烯加氢反应中有一诱导期。反应中涉及两种催化活性物种。     

水溶性铑－膦配合物的结构及性能表征

采用ＩＣＰ、ＦＴＩＲ、１３ＣＷＲ、３１ＰＮＭＲ、ＴＧＡ、ＸＰＳ等方法，对三种水溶性铑配合物：ＨＲｈ（ＣＯ）（ＴＰＰＴＳ）３、ＲｈＣｌ（ＣＯ）（ＴＰＰＴＳ）２和ＲｈＩ（ＣＯ）（ＴＰＰＴＳ）２的组成、结构和性质进行了表征．结果表明，采用新设计的方法合成的水溶性铑－膦配合物，具有以三苯基膦为配体的配合物类似的结构．它们的热稳定性很好，在水中的溶解度大，而在非极性有机溶剂中极难溶解，是良好的烯烃氢甲酰化催化剂．     

水溶性钯配合物催化柠檬醛的选择加氢研究 Ⅱ.催化剂的循环使用

研究了以水溶性ＰｄＣｌ２（ＴＰＰＴＳ）２为催化剂，在水／有机物两相体系中，添加ＴＰＰＴＳ、ＣＴＡＢ、ＰＶＡ、明胶和碳酸钠对柠檬醛加氢反应及催化剂稳定性的影响．添加配体ＴＰＰＴＳ、明胶或表面活性剂ＣＴＡＢ有利于减少钯黑的形成，但会引起催化活性的降低；而添加ＰＶＡ和Ｎａ２ＣＯ３，虽然都不能抑制钯黑的形成，但后者的添加会明显提高加氢速度；发现，明胶加碳酸钠的体系不仅可以稳定催化剂的活性物种，避免钯黑的析出，而且催化反应的转化率及选择性都较高．     

La(ClO4)3-OCBAAP-H2O体系(30℃)溶度及Ln(OCBAAP)4(ClO4)3·nH2O的合成和表征

测定了三元体系Ｌａ（ＣｌＯ４）３－ＯＣＢＡＡＰ－Ｈ２Ｏ在３０℃时的溶解度．结果表明，该体系有一个新固相（不一致溶解化合物）Ｌａ（ＯＣＢＡＡＰ）４（ＣｌＯ４）３·６Ｈ２Ｏ形成．参考该体系溶度图确定合成条件，合成了系列化合物Ｌｎ（ＯＣＢＡＡＰ）４（ＣｌＯ４）３·ｎＨ２Ｏ（Ｌｎ＝Ｌａ，ｎ＝６；Ｌｎ＝Ｐｒ，Ｎｄ，Ｓｍ，Ｇｄ，Ｙｂ，ｎ＝２）．通过化学分析、元素分析、ＴＧ－ＤＴＧ、ＩＲ和密度对化合物进行了表征，计算了Ｌａ（ＯＣＢＡＡＰ）４（ＣｌＯ４）３热分解过程各阶段的表观活化能．     

Carbonylation of Allyl Chloride Catalyzed by PdCl_2（TPPTS）_2 in Two－phase Medium

ＣａｒｂｏｎｙｌａｔｉｏｎｏｆＡｌｌｙｌＣｈｌｏｒｉｄｅＣａｔａｌｙｚｅｄｂｙＰｄＣｌ_２（ＴＰＰＴＳ）_２ｉｎＴｗｏ－ｐｈａｓｅＭｅｄｉｕｍＣａｒｂｏｎｙｌａｔｉｏｎｏｆＡｌｌｙｌＣｈｌｏｒｉｄｅＣａｔａｌｙｚｅｄｂｙＰｄＣｌ_２（ＴＰＰＴＳ）_２ｉｎ...     

烯丙基硫脲与支持电解质阴离子在银电极上共吸附的拉曼光谱

用表面增强拉曼散射光谱（ＳＥＲＳ）和时间分辨ＳＥＲＳ光谱（ＴＲＳＥＲＳ）等技术首次研究了烯丙基硫脲（ＡＴＵ）在ＨＣｌＯ４、Ｈ２ＳＯ４和ＨＮＯ３介质中与无机阴离子在银电极上的电化学共吸附行为．提出ＡＴＵ很可能以Ｓ端与银电极表面形成化学吸附键，仲氨基相对伯氨基距离表面较近，整个分子偏向烯丙基一侧倾斜吸附在表面上．ＣｌＯ－４、ＳＯ２－４和ＮＯ－３等弱吸附无机阴离子均能被ＡＴＵ诱导共吸附在其质子化了的仲氨基上，这３种无机阴离子被ＡＴＵ诱导共吸附的强弱顺序是ＣｌＯ－４＞ＳＯ２－４＞ＮＯ－３．被诱导共吸附的无机阴离子对ＡＴＵ在电极表面的化学吸附起到稳定剂的作用，有利于ＡＴＵ在电极表面形成致密的吸附层     

水溶性铑—膦配合物催化长链烯烃氢甲酰化反应研究—反应条件的影响

本文研究了两相催化体系中，在ＣＴＡＢ（Ｃ１６Ｈ３３ＮＭｅ３Ｂｒ）存在下，水溶性铑－膦配合物ＲｈＣｌ（ＣＯ）（ＴＰＰＴＳ）２对１－己烯氢甲酰化反应的催化性能，详细考察了反应温度、压力、膦／铑比等对催化活性的影响。结果表明，在１．０ＭＰａ恒压下，反应温度１００℃，膦／铑摩尔比为１６，Ｈ２：ＣＯ＝１：１的条件下，１－己烯氢甲酰化的转化频率（ＴＯＦ）可达到３９．８ｍｉｎ＾－１。在此反应条件下，有机相和水相     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Copper catalyzed/mediated synthetic methodology for ebselen and related isoselenazolones

Scope of the copper catalyzed/mediated selenium-nitrogen coupling reaction has been studied for the synthesis of isoselenazolones. It is noticed that the 2-chloro, 2-bromo-, and 2-iodo-aryl amides substrates can be exploited in the selenium-nitrogen coupling reaction by employing 25-100 mol % of CuI/1,10-phenanthroline (L) and potassium carbonate as a base in DMF. Furthermore, electron rich 2-chloro-arylamides also underwent selenium-nitrogen coupling reaction to give biologically important selenium-nitrogen heterocycles. Also, copper-catalyzed selenium-nitrogen coupling reaction has been meticulously applied for the synthesis of diaryl diselenides having methoxy, amine, and amide functionality from respective aryl iodides in the presence of stoichiometric amount of succinimide as an external Se-N coupling partner.