利用自制的单频激光器获得近通讯波段正交振幅压缩态光场

利用自制的1.34 μm和0.67 μm双波长输出单频激光器作为泵浦源,泵浦基于PPKTP晶体的光学参量放大器,通过边带锁频技术将光学参量放大腔腔长锁定在激光频率上,将泵浦光和信号光相对相位锁定在π相位,经参量缩小过程获得低于散粒噪声极限约3 dB的正交振幅压缩光.压缩光位于光纤通信窗口——1.3 μm波段.     

红外探测装置中光谱分光镜的设计与制备

在红外探测装置中,光谱分光镜是用来把3 μm～5 μm和8 μm～12 μm 2个波段的光谱分开的零件.介绍了一种在通用镀膜机上制备光谱分光镜的新工艺.在该膜系的设计过程中,把Willey公式引入到对其平均透过率最高值进行估算的过程中,同时针对国产镀膜机控制精度不高的特点,尽量使用规整膜层进行设计.为了进一步提高8 μm～12 μm波段的透过率,在膜系的最外侧引进了一层自行配制的低折射率氟化物材料,制备出了符合技术指标的红外光谱分光镜.     

聚合物微环电光开关的模拟和优化

利用耦合模理论、电光调制理论和微环谐振理论,提出一个完善合理的聚合物微环电光开关的器件模型,并给出了可用以分析微环谐振过程的光强传递函数,据此在谐振波长1 550 nm下对该器件进行了模拟和优化.结果表明：微环波导芯截面尺寸为1.8×1.8 μm2,波导芯与电极间的限制层厚度为1.1 μm,电极厚度为0.15 μm,微环半径为15.2 μm,微环与信道间的耦合间距为0.16 μm,光绕微环转300 圈即可形成稳定的谐振状态,此时的谐振时间约为147.4 ps.不加电压时,下信道的插入损耗约为0.8 dB,上信道的串扰约为－26 dB;当取工作电压等于19.7 V为开关电压时,上信道的插入损耗约为0.34 dB,下信道的串扰约为－20 dB.     

基于哈特曼波前传感器的非制冷红外成像光学读出系统

提出了一种新的基于哈特曼波前传感器(SHWS)的光学读出系统.该系统利用SHWS探测焦平面阵列(FPA)单元在受热前后反射波前斜率的变化量重构被探测物体的红外辐射图像.在理论上详细讨论其成像性能后,实验获得了单元尺寸为60 μm×60 μm,阵列大小为34 pixel×38 pixel的高温物体红外图像,其噪声等效温度差(NETD)约为3.8 K.优化系统参数设计,可以提高哈特曼波前传感器对到达角的测量精度进而获得更小的噪声等效温度差.     

深亚微米SOI射频 LDMOS功率特性研究

提出了一种SOI LDMOS大信号等效电路模型,并给出了功率增益和输入阻抗表达式. 基于制备的深亚微米SOI射频LDMOS,测试了功率增益和功率附加效率. 深入研究了SOI LDMOS功率特性与栅长,单指宽度,工作电压和频率之间关系. 栅长由0.5 μm减到0.35 μm时,小信号功率增益增加44％,功率附加效率峰值增加9％. 单指宽度由20 μm增加到40 μm,600 μm /0.5 μm器件小信号功率增益降低23％,功率附加效率峰值降低9.3％. 漏端电压由3 V增加到5 V,600 μm /0.3 关键词： SOI射频 LDMOS 深亚微米 功率增益 功率附加效率     

基于VO_2薄膜非致冷红外探测器光电响应研究

VO2 薄膜是非致冷微测辐射热红外探测器热敏电阻材料 .研究中应用微电子工艺制备了VO2 溅射薄膜红外探测器 ,在 2 96K的环境中测试了该探测器在不同的直流偏置、光调制频率下对 873K标准黑体源 8— 12 μm红外辐射的光电响应以及器件的噪声电压 ,在 10和 30Hz的调制频率下其响应率分别大于 17kV/W和接近 10kV/W .该探测器实现了探测率D 大于 1 0× 10 8cmHz/W ,热时间常量为 0 0 11s的 8— 12 μm非致冷红外探测     

LYB晶体主轴折射率测量与评价

采用自准直法测量了在30℃~170℃范围内,0.473 μm、0.632 8 μm、1.064 0 μm、1.338 μm等波长下LYB晶体的主轴折射率,得到Sellmeier方程并计算了1.319 μm下该晶体的主轴折射率,与实验测量的结果进行了比较,两者之间的吻合性较好.测量结果表明,该晶体具有较低的折射率以及折射率随温度变化小,热稳定性较好.     

红外3.7～4.8 μm波段折射/衍射光学系统的消热差设计

研究了衍射光学元件在红外折射/衍射混合光学系统中的消热差特性并给出了具体设计实例,该系统工作波段为3.7～4.8 μm,全视场角为7.12°,满足100%冷光阑效率.系统仅采用硅和锗两种材料,设计结果表明,该系统在-50～100℃温度范围内不仅成像质量接近衍射极限,而且结构简单、体积小、质量轻,适用于像元尺寸为30 μm、像元数320×240的凝视焦平面阵列探测器.     

用于光纤传像束的折-衍混合光学耦接器研究

在光学耦接器设计中引入衍射面,根据衍射光学元件的三级像差理论,分析了衍射面初始结构参量的求解规律,通过理论计算和ZEMAX光学软件的优化,给出工作波长0.4~0.7 μm,焦距27.5 mm,光学长度为64 mm,采用一个衍射面的耦接器设计实例.该耦接器适用于单丝直径16 μm,截面直径为6 mm的光纤传像束.对设计结果的分析表明,折-衍混合耦接器不仅在光学性能方面优于传统的光学耦接器,而且在尺寸和重量上有非常显著的减少.     

基于相移技术的显微数字全息重构细胞相位

介绍了用显微镜物镜、压电陶瓷和CCD建立的一套测量细胞相位的显微数字全息光路,基于相移技术,给出了重构相位的理论分析,并用洋葱磷片叶细胞作为测试样品,完成了测量细胞相位的实验.结果表明：该系统可以完成细胞相位重构,系统分辨率不低于1 μm.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.