钙钛矿型LaFe1-xCuxO3的光催化活性研究

用柠檬酸络合法制备了钙钛矿型LaFeO3及LaFe1-xCuxO3化合物，测定了其对酸性红3B等水溶性染料的光催化降解活性。利用红外、紫外和光声光谱、正电子寿命谱及光电子能谱等技术分析了LaFeO3的光催化性能及掺杂对其活性的影响。结果表明，掺杂Cu^2 可使LaFeO3的光催化活性明显提高。     

LaFe1—xCuxO3光催化降解水溶性染料的活性

采用柠檬酸法合成了钙钛矿型复合氧化物催化剂ＬａＦｅＯ３,并按不同比例进行掺杂,制备了ＬａＦｅ１－ｘＣｕＯ３（ｘ＝０．０１～０．０９）系列样品,以高压荧光汞灯为光源,测定了该系列样品对酸性红３Ｂ等水溶性染料的光催化降解活性。采用红外、紫外、光声光谱及正电子寿命谱等技术分析了催化剂的光催化性能及掺杂对活性的影响。结果表明,掺杂后ＬａＦｅＯ３的光催化活性明显提高,这主要与Ｂ离子的ｄ电子结构有关。     

LaFe1-xCuxO3的光催化性及正电子湮没研究

研究LaFeO3及微量掺铜LaFeO3的光催化活性,利用正电子湮没谱分析掺杂的影响,发现随着掺杂百分比的增加,正电子寿命逐渐下降达到一最小值,然后又上升;而光催化活性随掺杂百分比的增加逐渐上升达到最大值,然后下降。结果表明：LaFeO3掺杂后光催化活性得以提高;正电子湮没技术是研究点阵缺陷结构的有效方法之一。     

Zn掺杂的LaFeO_3纳米晶的制备及其光催化活性研究

以氧化镧、硝酸铁和硝酸锌为原料,用柠檬酸络合法制备了La1-xZnxFeO3(x=0,0.1,0.3,0.5,0.7)纳米光催化剂,对其进行了XRD,TEM,UV-vis,IR等测试,并研究了其对水溶性染料活性艳红X-3B的光催化活性。结果表明:制得的LaFeO3为钙钛矿型结构,Zn2+的少量掺杂不改变LaFeO3的钙钛矿型结构,当x=0.3时开始出现尖晶石型ZnFe2O4相,当x=0.5时光催化活性最好,x=0.7时钙钛矿的结构被破坏。适量的Zn2+掺杂可以提高LaFeO3的光催化活性。     

柠檬酸络合法制备La1-xPbxFeO3及其光催化性能

用柠檬酸络合法制备了钙钛矿型复合氧化物LaFeO3,并按不同比例进行掺杂,制备了La1-xPbxFeO3(x=0,0.1,0.3,0.5,0.7)。用XRD,SEM,IR,UV-vis等方法对其进行表征,其结构均为钙钛矿型。并测定了其对活性艳红X-3B水溶性染料脱色的光催化活性。实验结果表明:在A位掺杂Pb2 ,产生了较多氧空位,降低了光生电子与空穴的复合速率,使LaFeO3的光催化活性明显提高,其中La0.7Pb0.3FeO3效果最佳。     

钕掺杂对纳米TiO2光催化分解水制氢活性的影响

 采用溶胶-凝胶法制备了一系列纳米TiO2和掺杂Nd3+ 的纳米TiO2光催化剂,并通过XRD, UV-Vis, TEM和N2吸附等技术对其进行了表征和分析,考察了样品光催化分解水制氢的活性. 结果表明, Nd3+的掺杂使TiO2的相变温度从600 ℃提高到800 ℃, 同时有效抑制了TiO2的粒径增长,提高了粒子的分散性和样品的比表面积, Nd3+掺杂量越大,催化剂的比表面积越大. 掺杂Nd3+ 后, TiO2的光催化制氢活性提高,本实验中Nd3+的最佳掺杂量为0.1%, 此时催化剂的活性比未掺杂TiO2提高了3.5倍. 随着焙烧温度升高, TiO2和Nd3+/TiO2样品的光催化活性均下降,但同时一定量的金红石相与锐钛矿相共存所产生的协同效应也使样品的光催化活性有所提高.     

TiO2/LaFeO3微纳米纤维的可控制备及光催化性能简

利用静电纺丝技术及水热合成法制备了TiO2/LaFeO3异质结构. 采用场发射扫描电子显微镜(FE-SEM),X射线衍射(XRD),傅里叶变换红外(FTIR)光谱和紫外-可见漫反射光谱(UV-Vis)等手段对TiO2/LaFeO3微纳米纤维的结构和表面形态进行表征. 通过亚甲基蓝(MB)光降解反应研究了其光催化性能. 结果表明,不完全碳化TiO2纤维表面的缺陷位点是LaFeO3纳米粒子的有利生长点. TiO2/LaFeO3异质结材料的带隙明显窄于TiO2,光催化活性得到提高;经140 min紫外光照射后,TiO2/LaFeO3异质结催化剂对MB的降解率为65.34%,分析和探讨了其光催化机理.     

TiO_2/LaFeO_3微纳米纤维的可控制备及光催化性能

利用静电纺丝技术及水热合成法制备了TiO2/LaFeO3异质结构.采用场发射扫描电子显微镜(FESEM),X射线衍射(XRD),傅里叶变换红外(FTIR)光谱和紫外-可见漫反射光谱(UV-Vis)等手段对TiO2/LaFeO3微纳米纤维的结构和表面形态进行表征.通过亚甲基蓝(MB)光降解反应研究了其光催化性能.结果表明,不完全碳化TiO2纤维表面的缺陷位点是LaFeO3纳米粒子的有利生长点.TiO2/LaFeO3异质结材料的带隙明显窄于TiO2,光催化活性得到提高;经140 min紫外光照射后,TiO2/LaFeO3异质结催化剂对MB的降解率为65.34%,分析和探讨了其光催化机理.     

稀土离子掺杂对纳米TiO2光催化制氢活性的影响

采用溶胶-凝胶技术制备了纳米TiO2和一系列稀土离子掺杂的TiO2光催化剂,通过X射线衍射、透射电镜及N2吸附等技术对其进行了表征,考察了样品光催化分解水制氢的性能.结果表明,稀土离子掺杂有效抑制了TiO2粒子的生长,提高了粒子的分散性,增大了催化剂的比表面积,从而大幅度提高了其光催化分解水制氢的性能.其中,Gd3 掺杂的TiO2样品粒径最小,分散性最好,比表面积最大(是未掺杂TiO2的35倍).掺杂离子的电子构型对样品的光催化制氢活性有较大影响,具有全空电子构型的La3 和半充满电子构型的Gd3 掺杂的样品具有较高的光催化制氢活性(分别是未掺杂TiO2的3.69倍和3.72倍).     

La_(1-x)Sr_xFeO_3光催化降解水溶性染料

用柠檬酸法合成了钙钛矿型复合氧化物 La Fe O3,并按不同比例进行掺杂 ,制备了L a1-x Srx Fe O3( x=0 .0 1、0 .0 2、0 .0 3、0 .0 4、0 .0 5) .以荧光汞灯为光源测定了样品对不同染料的光催化降解活性 ,根据红外、紫外、光声光谱等技术对催化剂的分析结果 ,讨论了光催化性能及掺杂Sr2 对其活性的影响 ,结果表明 ,掺杂后 L a Fe O3的光催化活性明显提高     

Preparation of LaFe0.95Pd0.05O3 perovskites and their catalytic performances in methane combustion

The physic-chemical properties of LaFe0.95Pd0.05O3 perovskites were strongly dependent on the temperature of calcination. Most of the organic substances and inorganic impurities were readily removed at 723 K but single-phase and well crystallized perovskite structure was formed at 873 K. With further raising the calcination temperature, the crystallite size of LaFe0.95Pd0.05O3 increased considerably. The LaFe0.95Pd0.05O3 sample that calcined at 1073 K showed only comparable activity as the reference LaFeO3 catalyst, in particular below 923 K, but pre-treatment with the reaction gas at 1223 K resulted in significantly enhanced activity due to the generation of active PdO species on the surface. The hysteresis feature upon heating-cooling cycle further confirmed the strong interaction between Pd and LaFeO3 in the perovskite structure.     

以金属氧化物及钙钛矿结构化合物为活性组分的ZSM-5催化剂上NOx选择性还原研究

研究了在水蒸汽存在条件下,以ＮＨ３为还原剂,金属／ＺＳＭ－５催化剂和负载于ＺＳＭ－５上的钙钛矿结构催化剂上的ＮＯｘ选择性催化还原（ＳＣＲ）性能。实验结果表明,当反应气中通入水蒸汽时,各样品的催化活性均下降,同时伴随着Ｎ２选择性的增加。而Ｃｕ－ＺＳＭ－５样品却表现出独特的性能,在所有测定样品中具有最高的ＮＯｘ转化率（在４５０℃时达到６９％）,当有水蒸汽存在时,其活性没有下降,反而有所增加,４５０℃时     

钙钛矿型复合氧化物LaFeO3和LaCoO3的光催化活性

采用柠檬酸法合成了钙钛矿复合氧化物ＬａＦｅＯ３和ＬａＣｏＯ３,并以其为光催化剂对水溶性染料进行光催化降解实验,研究了不同光源和不同光照时间对降解脱色率的影响。结果表明ＬａＦｅＯ３和ＬａＣｏＯ３均有较强的光催化活性,而ＬａＣｏＯ３的光催化活性明显高于ＬａＦｅＯ３,这主要与Ｆｅ＾３＋和Ｃｏ＾３＋离子的电子构型以及Ｆｅ－Ｏ间和Ｃｏ－Ｏ间的结合能有关。     

Self-regeneration of Pd-LaFeO3 catalysts: new insight from atomic-resolution electron microscopy

Aberration-corrected transmission electron microscopy was used to study atomic-scale processes in Pd-LaFeO(3) catalysts. Clear evidence for diffusion of Pd into LaFeO(3) and out of LaFe(0.95)Pd(0.05)O(3-δ) under high-temperature oxidizing and reducing conditions, respectively, was found, but the extent to which these processes occurred was quite limited. These observations cast doubt that such phenomena play a significant role in a postulated mechanism of self-regeneration of this system as an automotive exhaust-gas catalyst.     

An application of the "coloring problem": structure-composition-bonding relationships in the magnetocaloric materials LaFe13-xSix

The LaFe(13)-(x)Si(x) (1.0 < or = x < or = 5.0) series is studied experimentally and theoretically to gain possible understanding for the relationships among geometrical structure, chemical composition, magnetic behavior, and physical properties as related to the magnetocaloric effect in these compounds. As the Si concentration increases, LaFe(13)-(x)Si(x) exhibits a structural transformation from the cubic NaZn(13) structure type to a tetragonal derivative due primarily to preferential ordering of Fe and Si atoms. At room temperature, LaFe(13)-(x)Si(x) crystallize in the cubic structure for the range 1 < or = x < or = 2.6 and in the tetragonal for 3.2 < or = x < or = 5. In the range 2.6 < or = x < or = 3.2, it shows a two-phase mixture. Temperature-dependent single-crystal X-ray diffraction experiments near the corresponding Curie temperatures were performed on the room-temperature cubic phases to examine the origin of the large isothermal magnetic entropy changes. A thorough statistical and structural analysis of the data indicates that the noncentrosymmetric F43c space group provides a more adequate atomic arrangement than the centrosymmetric Fm3c space group. This change in space group leads to divergence for specific sets of Fe-Fe distances below the Curie temperature that arises from tilting of Fe-centered [Fe(12)-(x)Si(x)] icosahedra. The noncentrosymmetric space group also agrees with the predominance of icosahedral clusters lacking local inversion symmetry. From extended Hückel and tight-binding linear muffin-tin orbital (TB-LMTO) electronic structure calculations on various model structures, the F43c model is more energetically favorable than the Fm3c model. Extended Hückel calculations on various icosahedral [Fe(12)-(n)Si(n)] (n = 1-5) clusters and TB-LMTO calculations on "LaFe(13)," LaFe(11)Si(2), and LaFe(9)Si(4) have also been carried out to study the effects of a main group element (Si) on stabilizing the cubic NaZn(13)-type structure, influencing the transformation between cubic and tetragonal symmetries, and to study relationships among their chemical bonding and magnetic properties.