Polypyrazolinones from aromatic di(propynoic ester)s and aromatic dihydrazines

Novel polypyrazolinones with inherent viscosities ranging from 0.12 to 0.44 dL/g were prepared by the Michael-type nucleophilic addition-cyclization of various dihydrazines with 3,3′-(1,3- or 1,4-phenylene)bis(ethyl propynoate) (1,3- or 1,4-PEP) and 3,3′-(1,4-phenylene)bis(phenyl propynoate) (1,4-PPhP) in N-methylpyrrolidone (NMP) solution at 25–110°C. The polymers exhibited moderate thermal stability with initial weight loss in air about 200°C and in nitrogen about 300°C (TGA). No apparent T_g′s were observed by DSC analysis. The synthesis and characterization of the polypyrazolinones is discussed.     

Hydrazine‐based polyimides from isomeric bis(chlorophthalimide)s

3,3′‐Dichloro‐N,N′‐biphthalimide (3,3′‐DCBPI), 3,4′‐dichloro‐N,N′‐biphthalimide (3,4′‐DCBPI), and 4,4′‐dichloro‐N,N′‐biphthalimide (4,4′‐DCBPI) were synthesized from 3‐ or 4‐chlorophthalic anhydrides and hydrazine in glacial acetic acid. The yield of 3,3′‐DCBPI (90%) was much higher than that of 4,4′‐DCBPI (33%) because of the better stability of the intermediate, 3‐chloro‐N‐aminophthalimide, and 3,3′‐DCBPI. A series of hydrazine‐based polyimides were prepared from isomeric DCBPIs and 4,4′‐thiobisbenzenethiol (TBBT) in N,N‐dimethylacetamide in the presence of tributylamine. Inherent viscosity of these polymers was in the range of 0.51–0.69 dL/g in 1‐methyl‐2‐pyrrolidinone (NMP) at 30 °C. These polyimides were soluble in 1,1,2,2‐terachloroethane, NMP, and phenols. The 5% weight‐loss temperatures (T_5%s) of the polymers were near 450 °C in N₂. Their glass‐transition temperatures (T_gs) determined by dynamic mechanical thermal analysis and differential scanning calorimetry increased according to the order of polyimides based on 4,4′‐DCBPI, 3,4′‐DCBPI, and 3,3′‐DCBPI. The hydrolytic stability of these polymers was measured under acid, basic, and neutral conditions and the results indicated that the order was 3,3′‐DCBPI/TBBT > 3,4′‐DCBPI/TBBT > 4,4′‐DCBPI/TBBT. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4933–4940, 2007     

The synthesis of a precursor of polybenzimidazole (PBI) and blends with polyamic acid (PAA)

The precursor of polybenzimidazole (PBI), poly(3,3′-diamino-4,4′-benzidine isophthalamide) (PDABI), was synthesized from poly(3,3′-dinitro-4,4′-benzidine isophthalamide) (PDNBI) by reduction. With increasing temperature, the NH₂ moiety which was protected by SnCl₅^?1 could cyclize and form PBI. Blends with polyamic acid (LaRC-TPI) were prepared. Clear blend films were prepared at up to 400°C. The IR spectra displayed shifts in the NH stretching band, thereby providing evidence for specific interactions related to the miscibility of their cured blends. © 1993 John Wiley & Sons, Inc.     

Polyquinoxalines. III

Six thermally stable polyquinoxalines have been prepared by the reactions of combinations of three tetraamines, 3,3′,4,4′-tetraaminodiphenyl sulfone (II), and 3,3′,4,4′-tetraaminodiphenyl ether (V), with two bisglyoxals, 4,4′-diglyoxalyldiphenyl sulfide dihydrate (III) and 4,4′-diglyoxalyldiphenyl sulfone dihydrate (IV). The polymers were prepared from polymerization in two stages. The first stage, a solution polymerization, produces an initially low or moderate molecular weight material, which is advanced to a high molecular weight (η_inh > 1.0) by heating at 375°C. under reduced pressure. All the polyquinoxalines have excellent thermal stability both in nitrogen and in air and improved solubility.     

Phenyl-substituted polyquinoxalines

Four phenyl-substituted polyquinoxalines have been prepared by the reaction of combinations of two tetraamines, 3,3′-diaminobenzidine and 3,3,′4,4′-tetraaminodiphenyl ether, with two bisbenzils, 4,4′-dibenzil and 4,4′-oxydibenzil. The polymers were prepared by melt and solution polymerizations. Melt condensations were performed at 180, 220, and 280°C. and samples were periodically removed and characterized. The solution polymerizations consisted of two stages, initially forming an intermediate molecular weight polymer (η_inh 0.6–1.0) which was advanced at 400°C. to final polymer (η_inh 1.5 to 2.2). Clear yellow films, cast from m-cresol solution, exhibited good toughness and flexibility. The phenyl-substituted polyquinoxalines exhibited excellent oxidative and thermal stability. Polymer decomposition temperatures in air were generally about 550°C. Isothermal aging at 371°C. (700°F.) in air showed weight retentions as high as 93 and 50% after 100 and 200 hr., respectively. Weight-average molecular weight determination by light-scattering technique on a polymer with an η_inh of 2.16 suggested a value of 247,000. Certain physical properties of the phenyl-substituted polyquinoxalines are compared with those of the corresponding ordinary polyquinoxalines to illustrate the advantageous effect of introducing a phenyl group on the quinoxaline ring.     

Fully imidized soluble polyimides based on a novel dianhydride: 2,2′-dichloro-4,4′,5,5′-benzophenone tetracarboxylic dianhydride

We have synthesized a novel dianhydride, 2,2′-dichloro-4,4′,5,5′-benzophenone tetracarboxylic dianhydride (DCBTDA). Polyimides were synthesized with DCBTDA or 3,3′,4,4′-benzophenone tetracarboxylic dianhydride (BTDA) and several relatively rigid meta- and para- substituted mononuclear diamines. The BTDA based systems were insoluble in dipolar, aprotic solvents whereas the DCBTDA based polymers displayed enhanced solubility in these solvents. The thermal stability of these polyimides was excellent as measured by 5% weight loss decomposition. The T_g's of the polymers were all above 290°C.     

Syntheses and properties of organosoluble polyimides based on 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐4, 7‐methanohexahydroindan

A series of organosoluble aromatic polyimides (PIs) was synthesized from 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐4,7‐methanohexahydroindan (3) and commercial available aromatic dianhydrides such as 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (ODPA), 4,4′‐sulfonyl diphthalic anhydride (SDPA), or 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropanic dianhydride (6FDA). PIs (III_c–f), which were synthesized by direct polymerization in m‐cresol, had inherent viscosities of 0.83–1.05 dL/g. These polymers could easily be dissolved in N,N′‐dimethylacetamide (DMAc), N‐methyl‐2‐pyrrolidone (NMP), N,N‐dimethylformamide (DMF), pyridine, m‐cresol, and dichloromethane. Whereas copolymerization was proceeded with equivalent molar ratios of pyromellitic dianhydride (PMDA)/6FDA, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA)/6FDA, or BTDA/SDPA, or ½ for PMDA/SDPA, copolyimides (co‐PIs), derived from 3 and mixed dianhydrides, were soluble in NMP. All the soluble PIs could form transparent, flexible, and tough films, and they showed amorphous characteristics. These films had tensile strengths of 88–111 MPa, elongations at break of 5–10% and initial moduli of 2.01–2.67 GPa. The glass transition temperatures of these polymers were in the range of 252–311°C. Except for III_e, the 10% weight loss temperatures (T_d) of PIs were above 500°C, and the amount of carbonized residues of the PIs at 800°C in nitrogen atmosphere were above 50%. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1681–1691, 1999     

New polyphenylquinoxalines linked by m-terphenyl flexibilizing groups

Three new monomers with phenylglyoxyloyl groups fixed on the 4,4′-, 4,6′-, and 4,4″-positions of m-terphenyl were synthesized by different pathways. They were used to prepare a series of polyphenylquinoxalines by solution polycondensation with 3,3′-diaminobenzidine and 3,3′,4,4′-tetraaminodiphenyl ether. These polymers exhibited excellent oxidative and thermal stability as shown by thermogravimetric analysis and isothermal aging in circulating air between 300 and 450°C. Clear yellow films, cast from m-cresol solution, were used to measure their softening temperature by thermomechanical analysis (TMA). Numerical data thus obtained, indicated a thermoplastic behavior in the temperature range 300 ± 15°C. Crosslinking of the linear polymers by isothermal heat exposure under argon between 300 and 500°C was investigated by means of TMA. Molded materials were fabricated under constant pressure (996 psi) at 500–525°C with an Instron testing machine. These polymers were also used for preliminary evaluation as matrices for 181-E glass reinforced composites. Flexural values obtained after isothermal aging in air up to 400°C indicated a potential use varying from 150 hr at 350°C to 24 hr at 400°C.     

A novel synthesis of polyethers with pendant hydroxyl groups by polyaddition of bis(oxetane)s with bis(phenol)s

The polyaddition of 1,4-bis[(3-ethyl-3-oxetanyl)methoxymethyl]benzene (BEOB) with 3,3′,5,5′-tetrachlorobisphenol A (TCBPA) was examined with or without catalysts. High molecular weight polymer (polymers 1) (M_n = 13,600) with pendant primary hydroxyl groups was obtained in a 99% yield without any gel products when the reaction was performed with 5 mol % of tetraphenylphosphonium bromide as a catalyst in NMP at 160°C for 96 h. However, when the reaction was carried out without a catalyst under the same conditions, a low molecular weight polymer (M_n = 3200) was obtained in a 51% yield. The structure of the resulting polymer was confirmed by IR, ¹H-NMR, and ¹³C-NMR spectra. In this reaction system, it was also found that tetraphenylphosphonium iodide and crown ether complexes such as 18-crown-6 (18-C-6)/KBr and 18-C-6/KI have high catalytic activity. Polyadditions of 1,4-bis[(3-methyl-3-oxetanyl)methoxymethyl]benzene with TCBPA and BEOB with 3,3′,5,5′-tetrabromobisphenol-S were also examined, and corresponding polymers (polymers 2 and 3) were obtained in good yields. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2781–2790, 1999     

Polyaddition reactions of bisethyleneureas and 1,1,3,3-diethyleneurea with polymethylene dimercaptans in LiCl-dimethylformamide

Polyaddition reactions of 1,1′-tetramethylenebis(3,3-ethyleneurea) (IIa), 1,1′-octamethylenebis(3,3-ethyleneurea) (IIb), 1,1′-p-phenylenebis(3,3-ethyleneurea) (IIc), 1,1′-(4,4′-diphenylmethane)bis(3,3-ethyleneurea) (IId) and 1,1,3,3-diethyleneurea (III) with polymethylene dimercaptans were investigated. 1,1′-Polymethylenebis(3,3-ethyleneureas) and polymethylene dimercaptans successfully reacted at 80–95°C. in the presence of triethylamine to give poly(urea sulfides) with intrinsic viscosities up to 1.1 in about 90% yield when dimethylformamide, dimethylacetamide, or N-methyl-2-pyrrolidone containing lithium chloride as a solvent were used. The other ethyleneureas, however, failed to give high molecular weight polymers.     

Synthesis and characterization of hyperbranched polyimides with good organosolubility and thermal properties based on a new triamine and conventional dianhydrides

A triamine monomer, 1,3,5‐tris(4‐aminophenoxy)benzene (TAPOB), was synthesized from phloroglucinol and 4‐chloronitrobenzene, and it was successfully polymerized into soluble hyperbranched polyimides (HB PIs) with commercially available dianhydrides: 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride (6FDA), 4,4′‐oxydiphthalic anhydride (ODPA), and 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA). Different monomer addition methods and different monomer molar ratios resulted in HB PIs with amino or anhydride end groups. From ¹H NMR spectra, the degrees of branching of the amino‐terminated polymers were estimated to be 0.65, 0.62, and 0.67 for 6FDA–TAPOB, ODPA–TAPOB, and BTDA–TAPOB, respectively. All polymers showed good thermal properties with 10% weight‐loss temperatures (T₁₀'s) above 505 °C and glass‐transition temperatures (T_g's) of 208–282 °C for various dianhydrides. The anhydride‐terminated HB PIs showed lower T₁₀ and T_g values than their amino‐terminated counterparts. The chemical conversion of the terminal amino or anhydride groups of the 6FDA‐based polyimides into an aromatic imido structure improved their thermal stability, decreased their T_g, and improved their solubility. The HB PIs had moderate molecular weights with broad distributions. The 6FDA‐based HB PIs exhibited good solubility even in common low‐boiling‐point solvents such as chloroform, tetrahydrofuran, and acetone. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3804–3814, 2002     

Aromatic polyamides and polyimides derived from 3,3′-diaminobiphenyl: Synthesis,characterization, and molecular simulation study

In this article a new synthesis of 3,3′-diaminobiphenyl (3,3′-DABP) is described, along with the preparation and characterization of polyamides and polyimides based on it. Reactivity of this monomer was calculated by a molecular simulation study, using ab initio quantum-mechanical methods. Terephthaloyl and isophthaloyl chloride were used for the synthesis of polyamides, while 3,3′,4,4′-biphenylenetetracarboxylic acid dianhydride and 4,4′-(hexafluoroisopropylidene) diphthalic anhydride were used for the synthesis of polyimides. Medium to high molecular weight polymers were attained, with inherent viscosities near or higher than 1.0 dL/g, the solubility of the 3,3′-DABP polymers was much better than that of the homologous polymers from benzidine (4,4′-DABP), the glass-transition temperatures were lower, by about 40°C, and the thermal resistance, as measured by thermogravimetry, was virtually the same. Amorphous films, made from cast polymer solutions, showed excellent mechanical properties, comparable to conventional aromatic polyamides and polyimides. Theoretical calculations demonstrated that the radius of giration, end-to-end distance and density of poly(3,3′-DABP-isophthalamide) were lower than those of poly(4,4′-DABP-isophthalamide), as a consequence of the chain folding induced in the backbone by the m-substitution in 3,3′-DABP. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4646–4655, 1999     

Two‐Dimensional Monovalent Copper Halide Coordination Polymers Incorporating Anti‐Conformation 3,3′‐Bipyridine

Hydrothermal treatment of aqueous mixtures of copper(II) halides and 3,3′‐bipyridine (3,3′‐bpy) has afforded the coordination polymers [CuCl(3,3′‐bpy)]_n ( 1 ) and [Cu₂Br₂(3,3′‐bpy)]_n ( 2 ), which were analyzed via single crystal X‐ray diffraction, infrared spectroscopy, and elemental analysis. The structure of 1 consists of two‐dimensional (2‐D) layers constructed from the linkage of castellated one‐dimensional (1‐D) [CuCl]_n stepped chains through anti‐conformation 3,3′‐bpy tethers. Compound 2 presents a related 2‐D sheet motif, albeit built from infinite 1‐D [Cu₂Br₂]_n ladders strutted by 3,3′‐bpy ligands in anti conformation. In both cases neighboring 2‐D sheets stack into 3‐D via weak C–H···halogen interactions.     

Studies on heat-resistant poly(metal phthalocyanine)-imide copolymers

Several new poly(metal phthalocyanine)imide copolymers have been prepared using 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BPTDA), metal(11) 4,4′,4″,4″′-phthalocyanine tetraamines (MPTA), p-phenylenediamine, 4,4′-methylenedianiline, and 9,9-bis(4-aminophenyl)-fluorene (BAF). The attractive feature of these polymers is their high thermooxidative and thermal stability. The polymer decomposition temperatures of all the imide copolymers are greater than 500°C in air and N atomspheres. Another noteworthy property is their high char yield: 60–78% at 800°C in a N₂ atmosphere. Variation of the metal phthalocyanine concentration has a remarkable effect on the thermal stability and degree of polymerization. The most preferred molar proportion of the reagents MPTA, diamine, and BTDA is 1.25:7.5:10. These polymers may be useful in the preparation of heat-resistant films and fibers.     

Synthesis and properties of poly(imide-sulfonate)s

Polycondensations of N,N′-bis(hydroxyalkyl)pyromellitic diimides, N,N′-bis(hydroxyphenyl)-pyromellitic diimides, N,N′-bis(hydroxyalkyl)-3,3′,4,4′-benzophenonetetracarboxylic diimides and N,N′-bis(hydroxyphenyl)-3,3′-4,4′-benzophenonetetracarboxylic diimides with aromatic disulfonyl chlorides were carried out in pyridine to produce poly(imide-sulfonate)s. The resulting polymers had inherent viscosities in the range of 0.25–0.38 dL/g. These poly(imide-sulfonate)s were insoluble in common organic solvents and had relatively good thermal stability. The TGA data showed 10% weight losses at 253–365°C and residual weights at 500°C were 22–72% in nitrogen.     

Triphenylphosphine oxide-based bismaleimide and poly(bismaleimide): Synthesis,characterization, and properties

A novel phosphorus-containing bismaleimide, 3,3′-bis(maleimidophenyl)phenylphosphine oxide (BMPPPO), was synthesized from triphenylphosphine oxide. This bismaleimide exhibited good solubility in common organic solvents, such as methylethylketone, methylisobutylketone, dichloromethane, chloroform, tetrahydrofuran, acetone, methanol, ethanol, and hot toluene. A low melting point (T_m = 148 °C), a relatively low polymerization temperature (T_p = 214 °C), and a wide processing window (T_p − T_m = 66 °C) were also obtained for BMPPPO. This implies better processing capability. In contrast to most known phosphorus-containing polymers, the incorporation of BMPPPO into poly(bismaleimide) enhanced the polymer glass-transition temperature. Thermal stability at temperatures over 550 °C and char yields in the high-temperature region over 700 °C were also improved. As a result, the flame-retardant properties of the poly(bismaleimide)s were improved. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1716–1725, 2001     

Chain Conformation and Local Rigidity of Isomerized Polyimides in Dimethyl Formamide by Size Exclusion Chromatography Coupled with Multi-Detectors

Chain conformation and local rigidity of two isomerized polyimides (PIs), poly(6FDA/3,3′-DMB) and poly(6FDA/2,2′-DMB) in dimethyl formamide (DMF) with either 0.1 M LiBr or 3.1 mM tetrabutylammonium bromide at 35 °C, are investigated. Size exclusion chromatography (SEC) coupled with multi-angle laser light scattering detector, viscometer, and differential refractive index detector was used. The scaling exponents α and ν related to conformation are estimated from the above results. The values of α and ν for poly(6FDA/3,3′-DMB) are 0.68 ± 0.01 and 0.54–0.55 ± 0.01, respectively. The values of α and ν for poly(6FDA/2,2′-DMB) are 0.65 ± 0.02 and 0.55 ± 0.01, respectively, which indicate that both PIs in DMF have a random coil conformation. In particular, poly(6FDA/3,3′-DMB) exhibits more extended conformation than that of poly(6FDA/2,2′-DMB). Parameters related to chain flexibility of polymers, including persistence length l _p, shift factor M _L (relative molecular weight per unit contour length), and backbone diameter d are evaluated from the relationship between intrinsic viscosity and molecular weight based on the wormlike continuous cylinder model. The three parameters (l _p, M _L, and d) indicate that the two samples are flexible chains with local rigidity, and poly(6FDA/3,3′-DMB) is slightly stiffer than poly(6FDA/2,2′-DMB). In addition, influence of salt types on the parameters is also discussed.

     

Synthesis and Characterization of Fluorinated Polyimide Derived from 3,3′‐Diisopropyl‐4,4′‐diaminodiphenyl‐3′′,4′′‐difluorophenylmethane

A novel aromatic diamine monomer, 3,3′‐diisopropyl‐4,4′‐diaminodiphenyl‐3′′,4′′‐difluorophenylmethane (PAFM), was successfully synthesized by coupling of 2‐isopropylaniline and 3,4‐difluorobenzaldehyde. The aromatic diamine was adopted to synthesize a series of fluorinated polyimides by polycondensation with various dianhydrides: pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (ODPA) and 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride (BTDA) via the conventional one‐step method. These polyimides presented excellent solubility in common organic solvents, such as N,N‐dimethylformamide (DMF), N,N‐dimethyl acetamide (DMAc), dimethyl sulfoxide (DMSO), N‐methyl‐2‐pyrrolidone (NMP), chloroform (CHCl₃), tetrahydrofuran (THF) and so on. The glass transition temperatures (T_g) of fluorinated polyimides were in the range of 260–306°C and the temperature at 10% weight loss in the range of 474–502°C. Their films showed the cut‐off wavelengths of 330–361 nm and higher than 80% transparency in a wavelength range of 385–463 nm. Moreover, polymer films exhibited low dielectric properties in the range of 2.76–2.96 at 1 MHz, as well as prominent mechanical properties with tensile strengths of 66.7–97.4 MPa, a tensile modulus of 1.7–2.1 GPa and elongation at break of 7.2%–12.9%. The polymer films also showed outstanding hydrophobicity with the contact angle in the range of 91.2°–97.9°.     

Preparation of phosphorus-containing polymers—XV. Preparation of phosphorus-containing polyamide-imides from N,N′-bis(4-carboxyphthalimido)-3,3′-diphenylalkylphosphine oxide and aromatic diacetamides

Phosphorus-containing polyamide-imides were prepared from N,N′-bis(4-carboxyphthalimido)-3,3′-diphenylalkylphosphine oxide and aromatic diacetamido derivatives by acidolysis; the reaction conditions are discussed. The resulting polymers were fairly soluble in DMA, DMF and conc. H₂SO₄; the reduced viscosities of polymers in DMA or cone. H₂SO₄ (0.2 g/dl) at 30° were 0.19–0.32. The phosphorus-containing polymers have good thermal stability, and are self-extinguished immediately after the flame is removed. Most of the i.r. absorption bands of polymers vanished on heating at above 600°.     

Synthesis and characterization of novel polybenzimidazoles bearing pendant phenoxyamine groups

A novel aromatic diacid, 3, 5‐dicarboxyl‐4′‐amino diphenyl ether, containing pendant phenoxy amine group was synthesized. Homo‐ and co‐polybenzimidazoles containing different content of pendant phenoxyamine groups were synthesized by condensation of 3,3′‐diaminobenzidine with this acid and a mixture of this acid and isophthalic acid in different ratio in polyphosphoric acid. Copolybenzimidazoles with structural variations were also synthesized based on this acid and pyridine dicarboxylic acid, terephthalic acid, adipic acid, or sebacic acid. The polymers have good solubility in polar aprotic solvents and strong acids and they form tough flexible films by solution casting. The polymers were characterized by different instrumental techniques (FTIR, TGA, DSC, XRD, etc.) and for solvent solubility, mechanical properties, inherent viscosity, and proton conductivity. The inherent viscosities of the polymers vary in the range of 0.62–1.52 dL/g. They have high thermal stability up to 475–506 °C (IDT) in nitrogen, high glass transition temperatures (T_g) ranging from 313 to 435 °C and good tensile strength ranging from 58 to 125 MPa. Proton conductivity of homo polymer is 3.72 × 10^?3 S/cm at 25 °C and 2.45 × 10^?2 S/cm at 200 °C © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5776–5793, 2008