A structural study of promethium metal under pressure

Abstract

The structural behaviour of Pm metal has been investigated up to 60 GPa of pressure using a Diamond Anvil Cell (DAC) and the energy dispersive X-ray diffraction technique. The room temperature/pressure structural form of Pm is dhcp and it transforms to a fcc phase by 10 GPa. This cubic phase of the metal converts by 18 GPa to a third phase, which has frequently been referred to as representing a distorted fcc structure. This latter form of Pm was retained up to 60 GPa, the maximum pressure studied, but subtle changes in the X-ray spectra between 50 and 60 GPa hinted that an additional structural change could be forthcoming at higher pressures. From the experimental data a bulk modulus (B₀) of 38 GPa and a B₀′ constant of 1.5 were calculated using the Birch equation. This modulus for Pm is in accord with the moduli reported for the neighboring lanthanide metals.     

Phase transition of samarium under high pressure

Abstract

The DAC X-ray power photograph method was employed for studing the phase transition of samarium up to 26.3 GPa. The experimental results show that the dhcp and fcc high pressure phase of Sm appeared at about 4.0 and 12.5 GPa and room temperature respectively. The dhcp phase was kept until 19.6 GPa. A model for Sm-type -? dhcp -? fcc phase transition is provided in this paper.     

Crystal structure and compressibility of FePt nanoparticles under high pressures and high temperatures

FePt nanoparticles with an average grain size of 4 nm and equiatomic composition of Fe and Pt was studied under high pressures in a diamond anvil cell to investigate its structural stability and compressibility under high compression. The ambient pressure disordered face-centered-cubic (fcc) phase was found to be stable to the highest pressure of 61 GPa (compression of 15%) at room temperature. The compression of Fe₅₀Pt₅₀ nanoparticles is closer to the compression curve for pure Pt and shows lower compressibility than what would be expected for a bulk Fe₅₀Pt₅₀ alloy. The nanoparticle character of Fe₅₀Pt₅₀ sample is maintained to the highest pressure without any observable grain coarsening effects at ambient temperature. Laser heating of disordered fcc phase at 32 GPa to a temperature of 2000 K resulted in a phase transformation to a microcrystalline phase with the distorted fcc structure.     

Pressure-induced phase transition in an orthorhombic C60 crystal

X-ray diffraction studies of an orthorhombic C₆₀ single crystal grown from CS₂ solution have revealed a phase transition to a monoclinic phase between 1.1 and 2.2GPa. Compressibility of three principal axes is measured up to 3GPa and found to be nearly isotropic. Its bulk modulus is obtained as 10.5±1.9GPa, and this crystal is more compressible than an fcc one. We discuss the structural characteristic differences under pressure between the orthorhombic crystal and the fcc crystal.     

Crystal Structure Transformations of Rare-Gas Solids Under Pressure

Pressure-induced structural changes in solid krypton (Kr) and xenon (Xe) have been studied using angle dispersive X-ray diffraction in a diamond-anvil cell (DAC) up to 50 GPa. The analysis of the results shows that in solid Kr (Xe) the phase transition from fcc to hcp starts below 3.2 GPa (1.5 GPa). Albeit the hcp/fcc ratio increases under pressure, both phases coexist up to the highest pressure reached in this study. Room temperature (RT) equations of state (EOS) are determined.     

Elastic moduli of single-crystal C60

The matrix of elastic constants of the fcc phase of solid C₆₀ has been determined experimentally from measurements of the the velocity of 5 MHz ultrasound in single-crystal samples with different crystallographic orientations. The following values were obtained for the elastic moduli: C ₁₁=14.9±0.9 GPa, C ₁₂=8.8±1.0 GPa, and C ₄₄=6.6±0.18 GPa. The results are compared with theoretical estimates of the elastic moduli and data obtained in previous measurements of the elastic characteristics of solid C₆₀. Fiz. Tverd. Tela (St. Petersburg) 40, 173–175 (January 1998)     

Performance of different types of detectors in a high-pressure X-ray study of phase transition

Abstract

Phase transitions in praseodymium and lanthanum under pressure have been studied using a synchrotron powder X-ray diffraction technique. A structure refinement of the distorted fcc phase of Pr using diffraction data collected with an imaging plate (IP) detector demonstrate that among some possible structures the rhombohedral structure with space group R3m best reproduces the observed diffraction pattern. The distorted fcc-fcc phase transition in La was observed as a function of the temperature at 23 GPa using a CCD-based detector. A five-minute exposure sufficiently long to measure the intensities of very weak superlattice reflections from the distorted fcc phase, which has been found to transform to the fcc phase at 550 K. The performance of the IP and a CCD-based detector are compared and their future developments discussed.     

High-pressure phases of thorium and uranium compounds with the rocksalt structure

Abstract

The high-pressure crystal structures of the actinide compounds ThX and UX (X= C, N, P, S, As, Se, Sb, Te) have been studied by X-ray diffraction using synchrotron radiation, in the pressure range up to about 60 GPa Distorted fcc structures were observed for UC (27 GPa), UN (29 GPa), UP (10/28 GPa), US (10 GPa) and ThS (20 GPa). No phase transition has been observed for ThC and ThN. Compounds with As, Se, Sb all transform to the CsCl structure. ThP transform to the CsCl structure at 30 GPa. ThTe has the CsCl structure at ambient pressure and no further phase transition has been observed. UTe transforms to the CsCl structure at 9 GPa.     

X-ray difffraction studies on samarium up to one megabar pressure

Abstract

High—pressure crystal structure studies have been performed on Sm up to 100 GPa using synchrotron x-radiation and a diamond anvil cell. The structural sequence Sm-dhcp-fcc-dist.fcc has been confirmed. There is no evidence of any volume collapse. The bulk modulus and its pressure derivative have been determined (B₀ = 30.7 GPa, B₀’ = 2.5).     

室温下Fe62Ni27Mn11（wt%）合金的压致fcc-hcp相变

 本文采用Mao-Bell型金刚石对顶砧（DAC）及高压在位（in situ）粉末X光衍射照相方法研究了Fe₆₂Ni₂₇Mn₁₁（wt%）合金在0~43.2 GPa压力范围内的压致结构相变和等温压缩行为，实验结果表明，该合金在低压时为fcc结构，在19.4 GPa压力附近出现压致fcc→hcp结构相变，直到43.2 GPa一直保持fcc、hcp二相共存；相变过程中，二相的molar体积相同；高压hcp相得晶格参数比值c/a基本上不随压力而变，可以表示为c/a=1.630±0.006；在卸压过程中，hcp相可保持到5.8 GPa，当卸压到常压时，该合金完全恢复到fcc结构；用Murnaghan等温固体状态方程对其压缩数据进行最小二乘法拟合，得到B₀=(166±12) GPa，B₀'=5.2±0.5；本文还给出了该合金的压致fcc→hcp结构相变模型，并对存在很宽的二相共存区间问题进行了初步探讨。     

Electron transport properties of lithium and phase transitions at high pressures

The electric resistivity and thermopower of lithium have been precisely measured at high pressures (up to 8 GPa) and temperatures from room temperature to 100°C. Transition to the fcc phase of lithium has been analyzed. The hysteresis of the direct and inverse transitions is 0.3 GPa at room temperature, decreases slightly with an increase in the temperature, and is almost independent of the prehistory of the sample. The phase transition line on the P-T diagram has a positive slope of dP/dT = 0.03 GPa/K. It is assumed that the fcc phase of lithium, which is stable at a high pressure, can appear for kinetic regions from the 9R phase, which is intermediate in energy between the bcc and fcc modifications.     

Structure and magnetism in compressed iron–cobalt alloys

Combined Co K-edge XANES-XMCD and XRD measurements were used to shed light on the magnetic and structural phase diagram of the Fe_1?x Co _x alloy under HP in the Co-rich region (x≥0.5). At 0.5≤x≤0.75, the alloy shows a pressure-induced structural/magnetic phase transition from bcc-FM to hcp-non-FM phase just like pure iron but at higher pressures. The x=0.9 sample has an fcc structure in the pressure range investigated but presents an FM to non-FM transition at P=64 GPa, a significantly lower pressure compared with pure Co (predicted ≈120 GPa), showing that Fe impurities strongly affect the HP Co response.     

Phase diagram and equations of state of BaSO4

Abstract

The phase diagram and equations of state of BaSO₄, were determined up to 29 GPa and 1000 K in a resistance-heating type diamond anvil cell. At room temperature, barite is the stable form of BaSO₄ which undergoes a reversible phase transition at 10 GPa. The high-pressure form is tentatively determined to be triclinic. At high temperature, a similar phase transition takes place in BaSO₄, but at a pressure higher than that at room temperature. Our results indicate that the phase boundary of the two polymorphs in BasO₄ has a positive slope (dT/dP) of 90 K/GPa. The equations of state for both barite and its high-pressure phase are reported.     

Electroconductivity and pressure–temperature states of step shocked C60 fullerite

A study of electrophysical and thermodynamic properties of C₆₀ single crystals under step shock loading has been carried out. The increase and the following reduction in specific electroconductivity of C₆₀ fullerite single crystals at step shock compression up to pressure 30 GPa have been measured. The equations of state for face centred cubic (fcc) C₆₀ fullerite as well as for two-dimensional polymer C₆₀ and for three-dimensional polymer C₆₀ (3D-C₆₀) were constructed. The pressure–temperature states of C₆₀ fullerite were calculated at step shock compression up to pressure 30 GPa and temperature 550 K. The X-ray diffraction studies of shock-recovered samples reveal a mixture of fcc C₆₀ and a X-ray amorphous component of fullerite C₆₀. The start of the formation of the X-ray amorphous component occurs at a pressure P _m≈ 19.8 GPa and a temperature T _m≈ 520 K. At pressures exceeding P _m and temperatures exceeding T _m, the shock compressed fullerite consist of a two-phase mixture of fcc C₆₀ fullerite and an X-ray amorphous component presumably consisting of the nucleators of polymer 3D-C₆₀ fullerite. The decrease in electroconductivity of fullerite can be explained by the percolation effect caused by the change of pressure, size and number of polymeric phase nuclei.     

A high pressure Raman study of terbium molybdate

Abstract

Tb₂(MoO₄)₃ has been studied by Raman spectroscopy under hydrostatic pressure up to 9 GPa at room temperature. The measurements reveal two phase transitions, one at around 2 GPa and another one above 5 GPa. The first phase transition is associated with an increase in the coordination number of Mo while the second is probably a transition to an amorphous phase in which only a wide band originating from Mo-O vibrations remains. This behaviour is irreversible as the Raman spectrum of the initial structure is not recovered at atmospheric pressure.     

Pressure-induced molecular dissociation in iodine at low temperatures

Abstract

Synchrotron x-ray diffraction experiments at low temperatures have revealed that even at 35K the molecular dissociation starts taking place at P_S=21.5 and finishes at P_f=26.1GPa. An extrapolation of the phase boundary thus obtained at several temperatures intersects the T=4K line at P_S=21.6 and P_f=26.3GPa. This result, inferring the monatomic structure to be realized at P=30GPa and T=4K, leads to a discrepancy against the recent Mössbauer result obtained at the same point in the P-T phase diagram.     

High-pressure crystal structure of thorium disulfide and diselenide and uranium disulfide

Abstract

The crystal structure of ThS₂, ThSe₂ and US₂ has been investigated for pressure up to 60GPa using x-ray powder diffraction. The bulk moduli are 175(10), 155(10) and 155(20) GPa, respectively. A pressure-induced phase transformation occurs at about 40 GPa for ThS₂, 30 GPa for ThSe₂ and 15 GPa for US₂. The results for ThSe₂ indicate that its high-pressure phase has a monoclinic structure. The same structure is compatible with the observed high-pressure spectra of ThS₂ and US₂. However, the crystal system assignment is less certain for these compounds.     

Phase Transition and Melting Curves of Calcium Fluoride via Molecular Dynamics Simulations

The phase transition and melting curves of CaF2 are investigated by using the general utility lattice programme （CULP） via the shell model with molecular dynamics method. By calculating the entropy H （at OK） and Cibbs free energy G^＊ （at 30OK）, we find that the phase transition pressure from the face-centred cubic （fee） structure to the orthorhombic structure is 11.40 CPa and 9.33 CPa at OK and 300K, respectively. The modified melting point of the fee CaF2 is in the range of 1650-1733K at OCPa. All these results are well consistent with the available experimental data and other theoretical results. We also obtain that the melting temperature of high pressure phase is 990-1073 K at 10 CPa. Moreover, the temperature dependences of the elastic constants Cij, bulk module B and shear module G are also predicted.     

Effects of pressure on the two polymorphs of [Co(NH3)5NO2]I2: The anisotropy of lattice distortion and a phase transition

Abstract

The effect of pressure on the two polymorphs of [CO(NH₃)₅NO₂]I₂ (phase I-orthorhombic, S.G. Pnma; phase II-monoclinic, S.G. C2/m) was studied by X-ray powder diffraction in a diamond anvil cell (DAC). In the presence of the ethanol-methanol-water mixture used as a pressure-transmitting liquid polymorph I was shown to undergo a phase transition at pressures between 0.45 GPa and 0.65 GPa. The diffraction pattern of the high-pressure phase (phase III) could be indexed as tetragonal with lattice parameters similar to those, which were previously reported for polymorph II in a 'pseudotetragonal setting'. The lattice distortions of phases II and III were studied at pressures up to 3.2 GPa and 3.7 GPa, correspondingly, and were shown to be very similar. Phases II and III were supposed to be very closely related. If poly(chlortrifluorethylen)-oil was used as a pressure-transmitting medium, no phase transitions were observed in phase I of [CO(NH₃)₅NO₂I₂ at least up to 1.8 GPa (the point when poly(chlortrifluorethylen)-oil becomes solid), and the anisotropy of lattice distortion could be measured.     

High-pressure phases of plutonium monoselenide studied by X-ray diffraction

Abstract

Plutonium monoselenide was studied under high pressure up to 47 GPa, at room temperature, using a diamond anvil cell in an energy dispersive X-ray diffraction facility. At ambient pressure, PuSe has the NaC1-type (B1) structure. The compound has been found to undergo a second-order crystallographic phase transition at around 20 GPa. This phase can be described as a distorted B1 structure, with a rhombohedral symmetry. PuSe transforms to a new phase at around 35 GPa, which can be indexed in the cubic CsCl-type (B2). The volume collapse at this phase transition is 11%. When releasing pressure, we observed a strong hysteresis to the inverse transformation down to 5 GPa. From the pressure-volume relationship, the bulk modulus has been determined to B ₀ = 98 GPa and its pressure derivative as B ₀ = 2.6. These results are compared to those obtained with other actinide monmictides and monochalcogenides.