The conductance and capacitance-frequency characteristics of Au/pyronine-B/p-type Si/Al contacts

The rectifying junction characteristics of the organic compound pyronine-B (PYR-B) film on a p-type Si substrate have been studied. The PYR-B has been evaporated onto the top of p-Si surface. The barrier height and ideality factor values of 0.67 ± 0.02 eV and 2.02 ± 0.03 for this structure have been obtained from the forward bias current-voltage (I-V) characteristics. The energy distribution of the interface states and their relaxation time have been determined from the forward bias capacitance-frequency and conductance-frequency characteristics in the energy range of ((0.42 ± 0.02) − E_v)-((0.66 ± 0.02) − E_v) eV. The interface state density values ranges from (4.21 ± 0.14) × 10¹³ to (3.82 ± 0.24) × 10¹³ cm⁻² eV⁻¹. Furthermore, the relaxation time ranges from (1.65 ± 0.23) × 10⁻⁵ to (8.12 ± 0.21) × 10⁻⁴ s and shows an exponential rise with bias from the top of the valance band towards the midgap.     

Effect of erbium interlayer on nickel silicide formation on Si(1 0 0)

To reveal the influence of erbium interlayer on the formation of nickel silicide and its contact properties on Si substrate, Er(0.5-3.0 nm) and Ni(20 nm) are successively deposited onto Si(1 0 0) substrate and are treated by rapid thermal annealing in pure N₂ ambient. The NiSi formation temperature is found to increase depending on the Er interlayer thickness. The formation temperature of NiSi₂ (700 °C) is not influenced by Er addition. But with 2 nm Er interlayer, the formed NiSi₂ is observed textured with preferred orientation of (1 0 0). During the formation of NiSi, Er segregates to the surface and little Er remains at the NiSi/Si(1 0 0) interface. Therefore, the Schottky barrier height of the formed NiSi/n-Si(1 0 0) contact is measured to be 0.635 ∼ 0.665 eV which is nearly invariable with different Er addition.     

Current transport mechanism in Al/Si3N4/p-Si (MIS) Schottky barrier diodes at low temperatures

The current-voltage (I-V) and capacitance-voltage (C-V) characteristics of metal-insulator-semiconductor (Al/Si₃N₄/p-Si) Schottky barrier diodes (SBDs) were measured in the temperature range of 80-300 K. By using the thermionic emission (TE) theory, the zero-bias barrier height Φ_B0 calculated from I-V characteristics was found to increase with increasing temperature. Such temperature dependence is an obvious disagreement with the negative temperature coefficient of the barrier height calculated from C-V characteristics. Also, the ideality factor decreases with increasing temperature, and especially the activation energy plot is nonlinear at low temperatures. Such behaviour is attributed to Schottky barrier inhomogeneties by assuming a Gaussian distribution of barrier heights (BHs) at interface. We attempted to draw a Φ_B0 versus q/2kT plot to obtain evidence of a Gaussian distribution of the BHs, and the values of Φ_Bo = 0.826 eV and α_o = 0.091 V for the mean barrier height and standard deviation at zero-bias, respectively, have been obtained from this plot. Thus, a modified ln(I_o/T²) − q²σ_o²/2(kT)² versus q/kT plot gives Φ_B0 and Richardson constant A^* as 0.820 eV and 30.273 A/cm² K², respectively, without using the temperature coefficient of the barrier height. This value of the Richardson constant 30.273 A/cm² K² is very close to the theoretical value of 32 A/cm² K² for p-type Si. Hence, it has been concluded that the temperature dependence of the forward I-V characteristics of the Al/Si₃N₄/p-Si Schottky barrier diodes can be successfully explained on the basis of TE mechanism with a Gaussian distribution of the barrier heights. In addition, the temperature dependence of energy distribution of interface state density (N_SS) profiles was determined from the forward I-V measurements by taking into account the bias dependence of the effective barrier height and ideality factor.     

The barrier height inhomogeneity in Al/p-Si Schottky barrier diodes with native insulator layer

The current-voltage (I-V) characteristics of Al/p-Si Schottky barrier diodes (SBDs) with native insulator layer were measured in the temperature range of 150-375 K. The estimated zero-bias barrier height Φ_B0 and the ideality factor n assuming thermionic emission (TE) theory show strong temperature dependence. Evaluation of the forward I-V data reveals an increase of zero-bias barrier height Φ_B0 but decrease of ideality factor n with increase in temperature. The conventional Richardson plot exhibits non-linearity below 250 K with the linear portion corresponding to activation energy of 0.41 eV and Richardson constant (A^*) value of 1.3 × 10⁻⁴ A cm⁻² K⁻² is determined from intercept at the ordinate of this experimental plot, which is much lower than the known value of 32 A cm² K² for holes in p-type Si. Such behavior is attributed to Schottky barrier inhomogene ties by assuming a Gaussian distribution of barrier heights (BHs) due to barrier height inhomogeneities that prevail at interface. Also, Φ_B0 versus q/2kT plot was drawn to obtain evidence of a Gaussian distribution of the BHs, and values of Φ_B0 = 1.055 eV and σ₀ = 0.13 V for the mean BH and zero-bias standard deviation have been obtained from this plot, respectively. Thus, the modified versus q/kT plot gives Φ_B0 and A^* as 1.050 eV and 40.08 A cm⁻² K⁻², respectively, without using the temperature coefficient of the barrier height. This value of the Richardson constant 40.03 A cm⁻² K⁻² is very close to the theoretical value of 32 A K⁻² cm⁻² for p-type Si. Hence, it has been concluded that the temperature dependence of the forward I-V characteristics of the Al/p-Si Schottky barrier diodes with native insulator layer can be successfully explained on the basis of TE mechanism with a Gaussian distribution of the barrier heights.     

Current-voltage characteristics of Au/GaN/GaAs structure

Au/GaN/n-GaAs structure has been fabricated by the electrochemically anodic nitridation method for providing an evidence of achievement of stable electronic passivation of n-doped GaAs surface. The change of the electronic properties of the GaAs surface induced by the nitridation process has been studied by means of current-voltage (I-V) characterizations on Schottky barrier diodes (SBDs) shaped on gallium nitride/gallium arsenide structure. Au/GaN/n-GaAs Schottky diode that showed rectifying behavior with an ideality factor value of 2.06 and barrier height value of 0.73 eV obeys a metal-interfacial layer-semiconductor (MIS) configuration rather than an ideal Schottky diode due to the existence of GaN at the Au/GaAs interfacial layer. The formation of the GaN interfacial layer for the stable passivation of gallium arsenide surface is investigated through calculation of the interface state density N_ss with and without taking into account the series resistance R_s. While the interface state density calculated without taking into account R_s has increased exponentially with bias from 2.2×10¹² cm⁻² eV⁻¹ in (E_c−0.48) eV to 3.85×10¹² cm⁻² eV⁻¹ in (E_c−0.32) eV of n-GaAs, the N_ss obtained taking into account the series resistance has remained constant with a value of 2.2×10¹² cm⁻² eV⁻¹ in the same interval. This has been attributed to the passivation of the n-doped GaAs surface with the formation of the GaN interfacial layer.     

Correlation between barrier heights and ideality factors of Cd/n-Si and Cd/p-Si Schottky barrier diodes

Our goal is to experimentally investigate whether or not the effective Schottky barrier heights (SBHs) and ideality factors obtained from the current-voltage (I-V) and capacitance-voltage (C-V) characteristics differ from diode to diode even if the samples were identically prepared. For this purpose, we prepared Cd/n-Si (33 dots) and Cd/p-Si (15 dots) diodes. The SBH for the Cd/n-Si diodes ranged from 0.701 to 0.605 eV, and ideality factor n from 1.913 to 1.213. Φ_b value for the Cd/p-Si diodes ranged from 0.688 to 0.730 eV, and ideality factor n value from 1.473 to 1.040. The experimental SBH distributions obtained from the C⁻²-V and I-V characteristics were fitted by a Gaussian function and their mean SBH values were calculated. Furthermore, the laterally homogeneous barrier heights were also computed from the extrapolation of the linear plot of experimental barrier heights versus ideality factors.     

The effect of interface states, excess capacitance and series resistance in the Al/SiO2/p-Si Schottky diodes

The current-voltage (I-V) characteristics of Al/SiO₂/p-Si metal-insulator-semiconductor (MIS) Schottky diodes were measured at room temperature. In addition the capacitance-voltage (C-V) and conductance-voltage (G-V) measurements are studied at frequency range of 10 kHz-1 MHz. The higher value of ideality factor of 3.25 was attributed to the presence of an interfacial insulator layer between metal and semiconductor and the high density of interface states localized at Si/SiO₂ interface. The density of interface states (N_ss) distribution profile as a function of (E_ss − E_v) was extracted from the forward bias I-V measurements by taking into account the bias dependence of the effective barrier height (Φ_e) at room temperature for the Schottky diode on the order of ≅4 × 10¹³ eV⁻¹ cm⁻²_. These high values of N_ss were responsible for the non-ideal behaviour of I-V and C-V characteristics. Frequency dispersion in C-V and G-V can be interpreted only in terms of interface states. The N_ss can follow the ac signal especially at low frequencies and yield an excess capacitance. Experimental results show that the I-V, C-V and G-V characteristics of SD are affected not only in N_ss but also in series resistance (R_s), and the location of N_ss and R_s has a significant on electrical characteristics of Schottky diodes.     

Current conduction mechanism in Al/p-Si Schottky barrier diodes with native insulator layer at low temperatures

The forward bias current-voltage (I-V) characteristics of Al/p-Si (MS) Schottky diodes with native insulator layer were measured in the temperature range of 80-300 K. The obtained zero bias barrier height Φ_B0(I-V), ideality factor (n) and series resistance (R_s) determined by using thermionic emission (TE) mechanism show strong temperature dependence. There is a linear correlation between the Φ_B0(I-V) and n because of the inhomogeneties in the barrier heights (BHs). Calculated values from temperature dependent I-V data reveal an unusual behaviour such that the Φ_B0 decreases, as the n and R_s values are increasing with decreasing absolute temperature, and these changes are more pronounced especially at low temperatures. Such temperature dependence of BH is contradictory with the reported negative temperature coefficient of the barrier height. In order to explain this behaviour we have reported a modification in the expression reverse saturation current I_o including the n and the tunnelling factor (αΧ^1/2δ) estimated to be 15.5. Therefore, corrected effective barrier height Φ_bef.(I-V) versus temperature has a negative temperature coefficients (α = −2.66 × 10⁻⁴ eV/K) and it is in good agreement with negative temperature coefficients (α = −4.73 × 10⁻⁴ eV/K) of Si band gap. In addition, the temperature dependent energy distribution of interface states density N_ss profiles was obtained from the forward bias I-V measurements by taking into account the bias dependence of the Φ_e and n. The forward bias I-V characteristics confirm that the distribution of N_ss, R_s and interfacial insulator layer are important parameters that the current conduction mechanism of MS Schottky diodes.     

Analysis of current-voltage characteristics of inhomogeneous Schottky diodes at low temperatures

Two approaches of Gaussian distribution of barrier heights in inhomogeneous Schottky diodes have been analyzed by comparing the results for consistency between the two. For this the current-voltage characteristics of inhomogeneous Schottky diodes have been generated by using analytically solved thermionic-emission diffusion equation incorporating Gaussian distribution of barrier heights and by direct numerical integration over a barrier height range. The differences in the results obtained in two approaches are discussed and it is shown that the two approaches yield current-voltage characteristics with slightly different features. The discrepancies in the results obtained in two approaches are attributed to the same series resistance assumed for all elementary barriers of the distribution. It is shown that assigning same series resistance to all barrier of the distribution in numerical integration approach causes current saturation at low bias and inhibits intersection of current-voltage curves from being observable which otherwise occurs in the curves obtained using analytical equation. The paper deals with these aspects in details.     

Temperature-dependent optical absorption measurements and Schottky contact behavior in layered semiconductor n-type InSe(:Sn)

The layered n-InSe(:Sn) single crystal samples have been cleaved from a large crystal ingot grown from non-stoichiometric melt by the Bridgman-Stockbarger method. It has been made the absorption measurements of these samples without Schottky contact under electric fields of 0.0 and 6000 V cm⁻¹. The band gap energy value of the InSe:Sn has been calculated as 1.36 ± 0.01 eV (at 10 K) and 1.28 ± 0.01 eV (at 300 K) under zero electrical field, and 1.31 ± 0.01 eV (at 10 K) and 1.26 ± 0.01 eV (at 300 K) under 6000 Vcm⁻¹. The current-voltage (I-V) characteristics of Au-Ge/InSe(:Sn)/In Schottky diodes have been measured in the temperature range 80-320 K with a temperature step of 20 K. An experimental barrier height (BH) Φ_ap value of about 0.70 ± 0.01 eV was obtained for the Au-Ge/InSe(:Sn)/In Schottky diode at the room temperature (300 K). An abnormal decrease in the experimental BH Φ_b and an increase in the ideality factor n with a decrease in temperature have been explained by the barrier inhomogeneities at the metal-semiconductor interface. From the temperature-dependent I-V characteristics of the Au-Ge/InSe(:Sn)/In contact, that is, and A^* as 0.94 ± 0.02 and 0.58 ± 0.02 eV, and 27 ± 2 and 21 ± 1 (A/cm² K²), respectively, have been calculated from a modified versus 1/T plot for the two temperature regions. The Richardson constant values are about two times larger than the known value of 14.4 (A/cm² K²) known for n-type InSe. Moreover, in the temperature range 80-320 K, we have also discussed whether or not the current through the junction has been connected with TFE.     

Inhomogeneities in 130 MeV Au ion irradiated Au/n-Si (1 0 0) Schottky structure

The electrical characteristics of Au/n-Si (1 0 0) Schottky rectifier have been studied in a wide irradiation fluence range using conventional current-voltage (I-V) and capacitance-voltage (C-V) measurements. The I-V characteristics showed an abnormal increase in forward current at low voltage. The device shows a bend in forward I-V and reverses bias C-V characteristics due to extra current, suggesting that there are two independent contributions to thermionic current, corresponding to two levels of the Schottky barrier. It is shown that the excess current at low voltage can be explained by taking into account the role of heavy ion irradiation induced defects at the metal semiconductor interface.     

Schottky barrier and pn-junctionI/V plots — Small signal evaluation

This paper proposes and examines three different plots for the determination of the saturation current, the ideality factor, and the series resistance of Schottky diodes and solar cells from the measurement of a single current (I)/voltage(V) curve. All three plots utilize the small signal conductance and avoid the traditional Norde plot completely. A test reveals that the series resistance and the barrier height of a test diode can be determined with an accuracy of better than 1%. Finally it is shown that a numerical agreement between measured and fittedI/V curves is generally insufficient to prove the physical validity of current transport models.     

Study of the early stages of Cr/6H-SiC(0 0 0 1) interface formation

The early stages of the Cr/6H-SiC(0 0 0 1) interface formation at room temperature were investigated using XPS, LEED and work function (WF) measurements. Upon stepwise Cr evaporation in UHV up to a thickness of 5-10 monolayers (ML) at RT, the binding energy of the XPS Cr 2p_3/2 core level peak shifted from 576.1 eV, at submonolayer coverage, to 574.7 eV (corresponding to metallic Cr) for the final Cr deposit, while the binding energies of the substrate XPS core level peaks remained stable. The WF exhibited a steep decrease of about 0.5 eV from the initial SiC substrate value, upon submonolayer coverage, but then increased gradually to saturation at a value of about 4.8 eV (polycrystalline Cr film with some chemisorbed oxygen). The growth of the ultrathin film was via 3D-cluster formation. The height of the Schottky barrier for the Cr/6H-SiC(0 0 0 1) contact was found by XPS to be 0.5 ± 0.1 eV. The results, generally, indicate the absence of any extended interfacial silicide-like interaction at RT.     

A note on TiN/Si (1 0 0) contacts

The contact properties of TiN on p- and n-type Si (1 0 0) obtained by magnetron reactive sputtering were investigated. Schottky diode characteristics were observed on p-type Si (1 0 0) as determined by forward current-voltage (I-V) measurements, but on n-type Si (1 0 0) the reverse I-V relation has shown a nonsymmetrical character. The zero-bias barrier heights evaluated by I-V on both type diodes were in the range of ∼0.60-0.64 V within the range of a few mVs, not more than ∼±(10-30) mV from each other. Incorporation of the effect of the series resistance in the I-V analysis resulted in a significant reduction in the magnitude of the ideality factor of the TiN/p-type specimen. Almost no change has occurred in the barrier height values. The contradictory reports on the TiN/n-type Si (1 0 0) diode characteristics in earlier works have been explained in terms of surface passivation of Si by the HF cleaning solution. It was stated in these reports that following annealing at 673 K the diodes have shown rectifying behavior. It has been speculated, that the nonsymmetrical nature of the TiN/n-Si (1 0 0) showing an intermediate behavior between Ohmic and rectifying behavior is a result of the specimen being exposed to a temperature lower than 673 K during sputtering where no complete depassivation took place. In order to obtain a rectifying behavior of TiN on both n-type and p-type Si surface passivation has to be eliminated.     

Chemical bonding and electronic structures at magnesium/copper phthalocyanine interfaces

Chemistry, electronic structure and electrical behavior at the interfaces between copper phthalocyanine (CuPc) and Mg with a reverse formation sequence were investigated using X-ray photoemission spectroscopy (XPS), ultraviolet photoemission spectroscopy (UPS), and current-voltage (I-V) measurements. A chemical reaction occurs between CuPc and Mg irrespective of the deposition sequence. Despite having different reaction zone thicknesses, both the CuPc-on-Mg and the Mg-on-CuPc interfaces exhibit chemistry-induced gap states and identical carrier injection barriers, which are confirmed by the symmetric electrical behavior obtained from I-V characteristics of devices with a structure of Mg/CuPc/Mg. These findings contrast with those expected from physisorptive noble metal-CuPc interfaces and suggest that strong local chemical bonding is a primary factor determining molecular level alignment at reactive metal-CuPc interfaces.     

Electrical Characteristics of Co/n-Si Schottky Barrier Diodes Using I-V and C-V Measurements

Electrical characteristics of Co/n-Si Schottky barrier diodes are analysed by current- voltage （I- V） and capacitancevoltage （C- V） techniques at room temperature. The electronic parameters such as ideality factor, barrier height and average series resistance are determined. The barrier height 0. 76 eV obtained from the C - V measurements is higher than that of the value 0. 70 eV obtained from the I - V measurements. The series resistance Rs and the ideality factor n are determined from the d ln（ I） /dV plot and are found to be 193.62 Ω and 1.34, respectively. The barrier height and the Rs value are calculated from the H（I） - I plot and are found to be 0.71 eV and 205.95Ω. Furthermore, the energy distribution of the interface state density is determined from the forward bias I - V characteristics by taking into account the bias dependence of the effective barrier height. The interface state density Nss ranges from 6.484×10^11 cm^-2eV^-1 in （Ec - 0.446） eV to 2.801×10^10 cm^-2eV^-1 in （Ec - 0.631） eV, of the Co/n-Si Schottky barrier diode. The results show the presence of a thin interracial layer between the metal and the semiconductor.     

Study of nickel silicide formation on Si(1 1 0) substrate

Nickel silicide formation on Si(1 1 0) and Si(1 0 0) substrate was investigated in this paper. It is confirmed that nickel monosilicide (NiSi) starts to form after 450 °C annealing for Si(1 0 0) substrate, but a higher annealing temperature is required for NiSi formation on Si(1 1 0) substrate, which is demonstrated by X-ray diffraction (XRD) and Raman scattering spectroscopy. The higher formation temperature of NiSi is attributed to the larger Ni₂Si grain size formed on Si(1 1 0) substrate. Ni silicided Schottky contacts on both Si(1 0 0) and Si(1 1 0) substrates were also fabricated for electrical characteristics evaluation. It clearly reveals that the rectifying characteristics of NiSi/n-Si(1 1 0) Schottky contacts is inferior to that of NiSi/n-Si(1 0 0) Schottky contacts, which is attributed to a lower Schottky barrier height and a rougher contact interface. The formation kinetics for nickel silicide on Si(1 1 0) substrate is also discussed in this paper.     

Study of Ni/Si(1 0 0) solid-state reaction with Al addition

The characteristics of Ni/Si(1 0 0) solid-state reaction with Al addition (Ni/Al/Si(1 0 0), Ni/Al/Ni/Si(1 0 0) and Al/Ni/Si(1 0 0)) is studied. Ni and Al films were deposited on Si(1 0 0) substrate by ion beam sputtering. The solid-state reaction between metal films and Si was performed by rapid thermal annealing. The sheet resistance of the formed silicide film was measured by four-point probe method. The X-ray diffraction (XRD) was employed to detect the phases in the silicide film. The Auger electron spectroscopy was applied to reveal the element profiles in depth. The influence of Al addition on the Schottky barrier heights of the formed silicide/Si diodes was investigated by current-voltage measurements. The experimental results show that NiSi forms even with the addition of Al, although the formation temperature correspondingly changes. It is revealed that Ni silicidation is accompanied with Al diffusion in Ni film toward the film top surface and Al is the dominant diffusion species in Ni/Al system. However, no Ni_xAl_y phase is detected in the films and no significant Schottky barrier height modulation by the addition of Al is observed.     

Intersecting behaviour of nanoscale Schottky diodes I-V curves

We describe a new feature connected with Schottky barriers with nanosize dimensions. We found out by theoretical analysis that the I-V curves of such small diodes measured at different temperatures should intersect and consecutively at higher voltages larger current flows through the diode at lower temperatures. This effect which is at first glance in contradiction with the thermionic theory is caused by the series resistance influence. We show that the presence of the series resistance is a necessary condition of its observation. However, the intersection voltage—minimum voltage at which the intersection may occur—increases with the value of the series resistance and the diode dimensions for which the effect could be observable in Si diodes and the common series resistance values must be in submicrometer range. Diodes with several hundreds nanometers dimension have the intersection voltage ∼1 V. Analytical expression for the intersection voltage values was also derived.     

A unified model for metal/organic interfaces: IDIS, ‘pillow’ effect and molecular permanent dipoles

A unified model, embodying the induced density of interface states (IDIS) model, the reduction of the metal work function due to the adsorbed molecules (‘pillow’ effect) and molecular permanent dipoles, is presented for describing the barrier formation at metal/organic interfaces. While the IDIS model and ‘pillow’ effect have been described in previous approaches, in this paper we show how to introduce molecular permanent dipoles in the interface barrier formation. Examples for Au or Al/organic interfaces are discussed, which show the validity of our results and the generality of our formalism.