Fabrication of hydrophobic surface of titanium dioxide films by successive ionic layer adsorption and reaction (SILAR) method

Titanium dioxide (TiO₂) films were fabricated on fluorine doped tin oxide (FTO) coated glass substrate using successive ionic layer adsorption and reaction (SILAR) method. The X-ray diffraction, scanning electron microscopy, transmission electron microscopy, optical absorption and contact angle measurement were applied to study the structural, surface morphological, optical and surface wettability properties of the as-deposited and annealed TiO₂ films. The X-ray diffraction studies revealed both as-deposited and annealed TiO₂ films are amorphous. Irregular shaped spherical grains of random size and well covered to the fluorine doped tin oxide coated glass substrates were observed from SEM studies with some cracks after annealing. The optical band gap values of virgin TiO_2, annealed, methyl violet and rose bengal sensitized TiO₂ were found to be 3.6, 3.5, 2.87 and 2.95 eV, respectively. Surface wettability studied in contact with liquid interface, showed hydrophobic nature as water contact angles were greater than 90°. The adsorption of dyes, as confirmed by the photographs, is one of the prime requirements for dye sensitized solar cells (DSSC).     

Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

Au/TiO2/Ru(0 0 0 1) model catalysts and their interaction with CO

Au/TiO₂/Ru(0 0 0 1) model catalysts and their interaction with CO were investigated by scanning tunneling microscopy and different surface spectroscopies. Thin titanium oxide films were prepared by Ti deposition on Ru(0 0 0 1) in an O₂ atmosphere and subsequent annealing in O₂. By optimizing the conditions for deposition and post-treatment, smooth films were obtained either as fully oxidized TiO₂ or as partly reduced TiO_x, depending on the preparation conditions. CO adsorbed molecularly on both oxidized and reduced TiO₂, with slightly stronger bonding on the reduced films. Model catalyst surfaces were prepared by depositing submonolayer quantities of Au on the films and characterized by X-ray photoelectron spectroscopy and scanning tunneling microscopy. From X-ray photoelectron spectroscopy, a weak interaction between the Au and the TiO₂ substrate was found. At 100 K CO adsorption occurred on both the TiO₂ film and on the Au nanoparticles. CO desorbed from the Au particles with activation energies between 53 and 65 kJ/mol, depending on the Au coverage. If the Au deposit was annealed to 770 K prior to CO exposure, the CO adsorption energy decreased significantly. STM measurements revealed that the Au particles grow upon annealing, but are not encapsulated by TiO_x suboxides. The higher CO adsorption energy observed for smaller Au coverages and before annealing is attributed to a significantly stronger interaction of CO with mono- and bilayer Au islands, while for higher particles, the adsorption energy becomes more bulk-like. The implications of these effects on the known particle size effects in CO oxidation over supported Au/TiO₂ catalysts are discussed.     

Preparation and photo-induced superhydrophilicity of composite TiO2-SiO2-In2O3 thin film

In this work, TiO₂-SiO₂-In₂O₃ composite thin films on glass substrates were prepared by the sol-gel dip coating process. X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF) and X-ray photoelectron spectroscopy (XPS) were used to evaluate the structural and chemical properties of the films. UV-vis spectrophotometer was used to measure the transmittance spectra of thin films. The water contact angle (WCA) of thin films during UV/vis irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that fabrication of composite film has a significant effect on transmittance and superhydrophilicity of TiO₂ films.     

Albumin adsorption on oxide thin films studied by spectroscopic ellipsometry

Thin films of tantalum, niobium, zirconium and titanium oxides were deposited by reactive magnetron sputtering and their wettability and surface energy, optical properties, roughness, chemical composition and microstructure were characterized using contact angle measurements, spectroscopic ellipsometry, profilometry, X-ray photoelectron spectroscopy and X-ray diffraction, respectively. The purpose of the work was to correlate the surface properties of the films to the Bovine Serum Albumin (BSA) adsorption, as a first step into the development of an initial in vitro test of the films biocompatibility, based on standardized protein adsorption essays. The films were immersed into BSA solutions with different protein concentrations and protein adsorption was monitored in situ by dynamic ellipsometry; the adsorption-rate was dependent on the solution concentration and the immersion time. The overall BSA adsorption was studied in situ using spectroscopic ellipsometry and it was found to be influenced by the wettability of the films; larger BSA adsorption occurred on the more hydrophobic surface, the ZrO₂ film. On the Ta₂O₅, Nb₂O₅ and TiO₂ films, hydrophilic surfaces, the overall BSA adsorption increased with the surface roughness or the polar component of the surface energy.     

XPS characterization of sensitized n-TiO2 thin films for dye-sensitized solar cell applications

TiO₂ thin films, employed in dye-sensitized solar cells, were prepared by the sol-gel method or directly by Degussa P25 oxide and their surfaces were characterized by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The effect of adsorption of the cis-[Ru(dcbH₂)₂(NCS)₂] dye, N3, on the surface of films was investigated. From XPS spectra taken before and after argon-ion sputtering procedure, the surface composition of inner and outer layers of sensitized films was obtained and a preferential etching of Ru peak in relation to the Ti and N ones was identified. The photoelectrochemical parameters were also evaluated and rationalized in terms of the morphological characteristics of the films.     

Transparent nano composite PVA–TiO2 and PMMA–TiO2 thin films: Optical and dielectric properties

Transparent nano composite PVA–TiO₂ and PMMA–TiO₂ thin films were prepared by an easy and cost effective dip coating method. Al/PVA–TiO₂/Al and Al/PMMA–TiO₂/Al sandwich structures were prepared to study the dielectric behavior. The presence of metal–oxide (Ti–O) bond in the prepared films was confirmed by Fourier transform infrared spectroscopy. X-ray diffraction pattern indicated that the prepared films were predominantly amorphous in nature. Scanning electron micrographs showed cluster of TiO₂ nanoparticles distributed over the film surface and also there were no cracks and pin holes on the surface. The transmittance of the films was above 80% in the visible region and the optical band gap was estimated to be about 3.77 eV and 3.78 eV respectively for PVA–TiO₂ and PMMA–TiO₂ films by using Tauc's plot. The determined refractive index (n) values were between 1.6 and 2.3. High value of dielectric constant (?′ = 24.6 and ?′ = 26.8) was obtained for the prepared composite films. The conduction in the composite films was found to be due to electrons. The observed amorphous structure, good optical properties and dielectric behavior of the prepared nano composite thin films indicated that these films could be used in opto-electronic devices and in thin film transistors.     

Deposition of graded TiO2 films featured both hydrophobic and photo-induced hydrophilic properties

Graded TiO₂ films were deposited on unheated glass substrates by using a twin dc magnetron sputtering system. The graded TiO₂ films showed a highly polycrystalline structure of anatase with a little rutile phases revealed by X-ray diffraction spectra. The surface energy of the fresh and UV irradiated films were evaluated by water contact angle measurement. The results indicated that the water contact angle of the fresh graded TiO₂ films was found within 100-112°. The films then became a highly hydrophilic surface with the water contact angle of almost zero under 60 min UV irradiation. The XPS spectrum of Ti 2p revealed that the graded TiO₂ films became a stoichiometric titanium oxide layer near the surface, proving that titanium was fully oxidized. It was found that the surface OH group density depended on the substrates employed for given sputtering conditions. In addition, AFM images revealed a considerably rough surface of the graded films with RMS roughness of 12.6-14.5 nm. One can conclude that the unique properties of highly hydrophobicity and photo-induced hydrophilicity can be attributed to fully oxidized chemical composition and higher roughness on the film surface.     

Methylene blue photoelectrodegradation under UV irradiation on Au/Pd-modified TiO2 films

In this work TiO₂ thin films were modified with gold/palladium (Au/Pd) bimetallic paticles by sputtering method. TiO₂ films were deposited on ITO (SnO₂:In) by Doctor Blade method and post-anneling. The properties of the films were studied through measurements of XRD (X-ray diffraction) and AFM (atomic force microscopy). The degradation of methylene blue was studied by UV-irradiated pure TiO₂ and Au/Pd-modified TiO₂ in aqueous solution. Langmuir-Hinshelwood model was used to obtain kinetic information. Photocatalytic study indicated that Au/Pd-modified TiO₂ photocatalytic activity was better than TiO₂ pure; the best half-life time for Au/Pd-modified TiO₂ in photodegradation was 2.8 times smaller than TiO₂ pure; finally the efficiency in methylene blue photodegradation was improved from 23% to 43% when Au/Pd-modified TiO₂ films were used.     

Characteristics of N-doped TiO2 thin films grown on unheated glass substrate by inductively coupled plasma assisted dc reactive magnetron sputtering

N-doped TiO₂ thin films have been deposited on unheated glass substrates by an inductively coupled plasma (ICP) assisted direct current (dc) reactive magnetron sputtering. All films were produced in the metallic mode of sputtering in order to achieve a high deposition rate. The structures and properties of the N-doped TiO₂ films were studied by X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, field emission scanning electron microscopy and UV–Vis spectrophotometer. Experimental results show that we can obtain well crystallized N-doped anatase phase TiO₂ thin films at low deposition temperature and at high deposition rate by using the ICP assisted dc reactive magnetron sputtering process. The doping of nitrogen into TiO₂ lattices leads to a smooth shift of the absorption band toward visible light regions.     

Annealing effects on microstructural and optical properties of Nanostructured-TiO2 thin films prepared by sol-gel technique

In this paper we report on the effect of annealing on the microsctructural and optoelectronic properties of titanium dioxide (TiO₂) thin films prepared using sol-gel method onto silicon (Si) (100) and quartz substrates. The annealing temperatures range from 200 to 1000 °C. The Microstructural properties of annealed thin films were investigated by Thermal gravimetric analyses (TGA), X-ray diffraction (XRD) and Raman Spectroscopy. The surface morphology of the film was examined using Atomic Force Microscopy (AFM) method. The optical properties of TiO₂ thin films were characterized using UV-VIS and Spectroscopic ellipsometry. The results have shown that the TiO₂ thin films persist in the anatase phase even after annealing at 800 °C. The phase transformation from anatase to rutile occurred only when the films were annealed at 1000 °C. AFM studies revealed nanocrystalline structure where their shape and density depend strongly on the annealing temperatures. The elaborated nanostructured-TiO₂ thin films present a high transparency in the visible range. Spectroscopic ellipsometry (SE) study was used to determine the effect of annealing temperature on the thickness and on the optical constant of TiO₂ thin films. Spectroscopic ellipsometry and UV-VIS shows that the band gap of TiO₂ thin films was found to decrease when the annealing temperature increases. The Anatase phase was find to show higher photocatalytic activity than the rutile one.     

Influence of annealing temperature on the photoluminescence property of ZnO thin film covered by TiO2 nanoparticles

In this work, ZnO thin films covered by TiO₂ nanoparticles (labeled as TiO₂-ZnO thin films) were prepared by electron beam evaporation. The influence of annealing temperature on the photoluminescence property of the samples was studied. The structures and surface morphologies of the samples were analyzed by X-ray diffraction (XRD) and atomic force microscope, respectively. The photoluminescence was used to investigate the fluorescent properties of the samples. The measurement results show that the ultraviolet emission of ZnO thin films is largely enhanced after they are covered by TiO₂ nanoparticles, while the green emission is suppressed. However, when the annealing temperature is relatively high (≥500 °C), the intensity of ultraviolet emission drops off and a violet emission peak along with a blue emission peak appears. This is probably connected with the atomic interdiffusion between TiO₂ nanoparticles and ZnO thin film. Therefore, selecting a suitable annealing temperature is a key factor for obtaining the most efficient ultraviolet emission from TiO₂-ZnO thin films.     

The synthesis and kinetic growth of anisotropic silver particles loaded on TiO2 surface by photoelectrochemical reduction method

Silver nanorods with average diameters of 120-230 nm and aspect ratio of 1.7-5.0 were deposited on the surface of TiO₂ films by photoelectrochemical reduction of Ag⁺ to Ag under UV light. The composite films prepared on soda-lime glass substrates were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The results show that the TiO₂ film after UV irradiation in AgNO₃ solution is composed of anatase phase TiO₂ and metallic silver with face centered cubic structure. Other compounds cannot be found in the final films. The maximum deposition content of silver particles on the surface of TiO₂ film was obtained with the AgNO₃ concentration of 0.1 M. The kinetic growth rates of silver particles can be controlled by photocatalytic activity of TiO₂ films. The studies suggest that the growth rates of silver particles increase with the enhancement of photocatalytic activity of TiO₂ films. The maximum growth rate of silver particles loaded on TiO₂ films can be up to 0.353 nm min⁻¹ among samples 1#, 2# and 3#, while the corresponding apparent rate constant of TiO₂ is 1.751 × 10⁻³ min⁻¹.     

Effects of γ rays irradiation on structure and property of TiO2 thin films

TiO₂ thin films were deposited on a glass substrate by the radio frequency magnetron sputtering method, and annealed for 2 h at temperatures of 550°C. Then, ⁶⁰Co γ rays with different doses were used to irradiate the resulting TiO₂ thin films. The surface features of films before and after irradiation were observed by scanning electron microscope (SEM). Simultaneously, the crystal structure and optical properties of films before and after irradiation were studied by X-ray diffraction (XRD), UV–VIS transmission spectrum and Photoluminescence (PL) spectrum, respectively. The SEM analysis shows that the film is smooth with tiny particles on the film surface, and non-crystallization trend was clear after irradiated with γ rays. The XRD results indicated that the structure of the film at the room temperature mainly exists in the form of amorphous and mixed crystal at a sputtering power of 200 W, and non-crystallinity was more obvious after irradiation. Obvious difference can be found for the transmissibility of the irradiated and pre irradiation TiO₂ films by the UV-VIS spectra. The color becomes light yellow, and the new absorption edge also appeared at about 430 nm. PL spectra and photocatalysis experiments indicate that the photocatalysis degradation rate of the TiO₂ films on methylthionine chloride solution irradiated with the maximum dose can be increased to 90%.     

Preparation of TiO2 thin films from autoclaved sol containing needle-like anatase crystals

A new inorganic sol-gel method was introduced in this paper to prepare TiO₂ thin films. The autoclaved sol with needle-like anatase crystals was synthesized using titanyl sulfate (TiOSO₄) and peroxide (H₂O₂) as starting materials. The transparent anatase TiO₂ thin films were prepared on glass slides from the autoclaved sol by sol-gel dip-coating method. A wide range of techniques such as Fourier transform infrared transmission spectra (FT-IR), X-ray diffraction (XRD), thermogravimetry-differential thermal analysis (TG-DTA), scanning electron microscopes, X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible spectrum were applied to characterize the autoclaved sol and TiO₂ thin films. The results indicate that the autoclaved sol is flavescent, semitransparent and stable at room temperature. The anatase crystals of TiO₂ films connect together to form net-like structure after calcined and the films become uniform with increasing heating temperature. The surface of the TiO₂ films contain not only Ti and O elements, but also a small amount of N and Na elements diffused from substrates during heat treatment. The TiO₂ films are transparent and their maximal light transmittances exceed 80% under visible light region.     

Synthesis of nanoporous TiO2 materials using a doubly surfactant system and applying them as useful adsorbents

Hydrothermal and non-hydrothermal nanoporous TiO₂ materials were synthesized via a doubly surfactant route by using cationic cetyltrimethylammonium bromide and anionic sodium dodecyl sulfate surfactants as the molecular template/structure directing agent. Hydrothermal treatment was performed for comparison. The bulk chemical and phase compositions, crystalline structures, particle morphologies, thermal stabilities and surface texturing were determined by means of X-ray powder analysis, SEM and N₂ sorptiometry. The nanoporous TiO₂ materials were found to have a spherical morphology with a diameter range of 50–200 nm and a high surface area (390 m² g^?1). Hydrothermal and non-hydrothermal nanoporous TiO₂ materials were applied for adsorption of heavy metal cations and the toxic organic compound, copper phthalocyanine, from water for evaluation of their adsorption properties. Both nanoporous TiO₂ materials were found to have similar adsorption capacities toward heavy metal cations and CuPc. Both hydrothermal and non-hydrothermal TiO₂ nanoporous materials were found to have very good potential for application as a new adsorbent especially for adsorbing heavy metal cations from wastewaters.     

Optical and hydrophilic properties of Cr doped TiO2-SiO2 nanostructure thin film

Cr doped TiO₂-SiO₂ nanostructure thin film on glass substrates was prepared by a sol-gel dip coating process. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the structural and chemical properties of the films. A UV-vis spectrophotometer was used to measure the transmittance spectra of the thin film. The hydrophilicity of the thin film during irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that Cr doping has a significant effect on the transmittance and super-hydrophilicity of TiO₂-SiO₂ thin film.     

Co离子注入TiO2薄膜的显微结构和磁性研究

利用直流磁控溅射技术在玻璃衬底上沉积了TiO₂薄膜,并对其进行了Co离子注入,最后在真空中500 ℃退火50 min,得到系列薄膜样品. 利用剥离-分散方法制备了薄膜的透射电镜样品,并用扫描电镜(SEM)、X射线能量散射谱(EDX)和高分辨透射电镜(HRTEM)对样品做了近似原位观察,研究了薄膜样品中不同Co离子注入深度的成分分布和显微结构. 结果表明,薄膜呈锐钛矿结构,Co元素主要分布在薄膜表层,Co离子的注入使TiO₂薄膜的晶粒被部分破坏,并形成CoO,而5 关键词： 2薄膜')" href="#">Co注入TiO₂薄膜 电镜原位观察 室温铁磁性     

Nanocoral architecture of TiO2 by hydrothermal process: Synthesis and characterization

TiO₂ thin films with novel nanocoral-like morphology were successfully grown directly onto the glass and conducting fluorine doped tin oxide coated glass substrates via multi-step hydrothermal (MSH) process. Titanium chloroalkoxide [TiCl₂ (OEt)₂ (HOEt)₂)] precursor was used in an aqueous saturated NaCl in presence of 1 mM HCl catalyst and HNO₃ peptizer at 120 °C. Reaction time varied from 3 to 12 h. The morphological features and physical properties of TiO₂ films were investigated by field emission scanning electron microscopy, high resolution transmission electron microscopy, X-ray diffraction, Fourier transform IR spectroscopy, Fourier transform Raman spectroscopy, room temperature photoluminescence spectroscopy and X-ray photoelectron spectroscopy. The surface morphology revealed the formation of TiO₂ corals having nanosized (30-40 nm) polyps. The photoelectrochemical properties of the TiO₂ nanocoral electrodes were investigated in 0.1 M NaOH electrolyte under UV illumination. The results presented in this study highlight two major findings: (i) ability to tune the photoelectrochemical response and photoconversion efficiency via controlled thickness of TiO₂ nanocorals and (ii) the substantial increase in short circuit photocurrent (J_sc) due to the improved charge transport through TiO₂ nanocorals prepared via MSH process. This approach would be quite useful for the fabrication of nanocoral architecture that finds key applications in photocatalysis, dye-sensitized solar cells and hybrid solar cells.     

Controlling the orientation of ZnO nanorod arrays using TiO<Subscript>2</Subscript> thin film templates dip-coated by sol–gel

The oriented ZnO nanorod arrays have been synthesized on a silicon wafer that coated with TiO₂ films by aqueous chemical method. The morphologies, phase structure and the photoluminescence (PL) properties of the as-obtained product were investigated by field-emission scanning electron microscopy (FE-SEM), X-ray diffractometer (XRD), transmission electron microscope (TEM) and PL spectrum. The nanorods were about 100 nm in diameter and more than 1 μm in length, which possessed wurtzite structure with a c axis growth direction. The room-temperature PL measurement of the nanorod arrays showed strong ultraviolet emission. The effect of the crystal structure and the thickness of TiO₂ films on the morphologies of ZnO nanostructures were investigated. It was found that the rutile TiO₂ films were appropriate to the oriented growth of ZnO nanorod arrays in comparison with anatase TiO₂ films. Moreover, flakelike ZnO nanostructures were obtained with increasing the thickness of anatase TiO₂ films.