Synthesis of fluorinated TiO2 hollow microspheres and their photocatalytic activity under visible light

Fluorinated TiO₂ hollow microspheres with three-dimensional hierarchical architecture were prepared by solvothermally treatment using solid microspheres as precursor. The obtained solid and hollow TiO₂ microspheres were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectrum (DRS) and photoluminescence (PL) spectra. The photocatalytic activity of as-prepared solid and hollow TiO₂ microspheres was determined by degradation of methyl orange (MO) under visible light irradiation. The results showed that the surface fluorination, the existence of accessible mesopores channels, and the increased light harvesting abilities could remarkably improve the photocatalytic activity of TiO₂ hollow microspheres.     

Improvement in the photocatalytic activity of TiO2 by the partial oxidation of the C impurities

TiO₂ was treated by water in an ultrasonic bath, resulting in the enhancement of the photocatalytic activity for the decomposition of methylene blue under UV and visible light irradiation. No change in the crystallinity and optical properties of TiO₂ by the H₂O-treatment was observed. The X-ray photoelectron spectroscopy (XPS) and FT-IR data revealed that the C impurities were oxidized by this treatment, indicating that the change in the structure of the C impurities plays a pivotal role in the photocatalytic activity of TiO₂.     

Effect of surface species on Cu-TiO2 photocatalytic activity

The Cu-TiO₂ nanoparticles with different Cu dopant content were prepared by sol-gel method. The structure of the as-prepared catalysts and the surface species of Cu-TiO₂ were determined using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and diffuse reflection spectroscopy (DRS). The relationship between the photocatalytic activity and the surface species of Cu-TiO₂ was revealed via the measurement of surface photovoltage spectroscopy (SPS) as well as the degradation of the rhodamine B (RhB). The experimental results suggest that the Cu-TiO₂ photocatalysts with appropriate content of Cu (about 0.06 mol%) possess abundant electronic trap, which effectively inhibits the recombination of photoinduced charge carriers, improving the photocatalytic activity of TiO₂. While at high Cu dopant region (>0.06 mol%), the excessive oxygen vacancies and Cu species can become the recombination centers of photoinduced electrons and holes. Meanwhile, at heavy Cu doping concentration, excessive P-type Cu₂O can cover the surface of TiO₂, which leads to decrease in the photocatalytic activity of photocatalyst. The photocatalytic experimental results are in good agreement with the conclusions of SPS measurements, indicating that there is a close relationship between the photocatalytic activity and the intensity of SPS spectra.     

Synthesis of anatase TiO2 nanowires by modifying TiO2 nanoparticles using the microwave heating method

Anatase TiO₂ nanowires with a diameter of 5-10 nm and length of 500 nm to 2 μm have been successfully synthesized by modifying TiO₂ nanoparticles (P25) using the microwave heating method. The microwave power, reaction pressure, and reaction time for the synthesis of TiO₂ nanowires were 500 W, 0.5-3.0 MPa (corresponding to a temperature range of 175-260), and 40-70 min, respectively. X-ray diffraction (XRD), field-emission scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), and the BET techniques were used to investigate the phase structures, morphologies, and specific surface areas of the TiO₂ nanowires. The effects of reaction time, pressure, and different post-treatment processes on the microstructures of TiO₂ nanowires were discussed. It has been shown that the microwave heating method is efficient in transforming TiO₂ nanoparticles to anatase TiO₂ nanowires.     

Sunlight photocatalytic activity of CdS modified TiO2 loaded on activated carbon fibers

To improve the photocatalytic application performances of TiO₂, in this work, firstly CdS modified Degussa P25 TiO₂ (CdS/TiO₂) composites were prepared by two methods, sol-gel method and precipitation method. Next they, sol-gel-CdS/TiO₂ (sg-CdS/TiO₂) and precipitation-CdS/TiO₂ (pp-CdS/TiO₂), were loaded on activated carbon fibers (ACFs) by dip-coating method using the sodium carboxymethyl cellulose as adhesives. The composites were characterized by XRD, UV-vis absorbance spectra, SEM, EDS and BET. The photocatalytic activities under sunlight were investigated by the degradation of methylene blue. The results showed that CdS/TiO₂ composites were mainly composed of anatase-TiO₂ and little CdS cubic phases. The absorption wavelengths of sg-CdS/TiO₂ and pp-CdS/TiO₂ composites were extended to 590 nm and 740 nm, respectively. The absorption edge had a pronounced ‘red shift’. From EDS analysis, the elemental contents of CdS/TiO₂ were mainly Ti and O and a small quantity of S and Cd. CdS/TiO₂ loaded on ACFs were in the form of small clusters, but not very uniform; compared with the original ACFs, the surface area and pore volume of CdS/TiO₂/ACFs decreased slightly, respectively, while the average pore diameter was not changed. The photodegradation rate of methylene blue under sunlight with CdS/TiO₂/ACFs composites was markedly higher than that of P25-TiO₂/ACFs, and the effect of pp-CdS/TiO₂/ACFs composites was better than that of sg-CdS/TiO₂/ACFs, when irradiated for 180 min, and the photodegradation rate of methylene blue reached to 90.1%. The photodegradation kinetics of the methylene blue fitted with the Langmuir-Hinshelwood equation. The apparent reaction rate constants of sg-CdS/TiO₂/ACFs and pp-CdS/TiO₂ were 0.0105 min⁻¹ and 0.0146 min⁻¹, respectively, which were about 1.3-1.7 times as large as that of P25-TiO₂/ACFs.     

Photoelectrochemical property and photocatalytic activity of N-doped TiO2 nanotube arrays

N-doped TiO₂ nanotube arrays (NTN) were prepared by anodization and dip-calcination method. Hydrazine hydrate was used as nitrogen source. The surface morphology of samples was characterized by SEM. It showed that the mean size of inner diameter was 65 nm and wall thickness was 15 nm for NTN. The ordered TiO₂ nanotube arrays on Ti substrate can sustain the impact of doping process and post-heat treatment. The atomic ratio of N/Ti was 8/25, which was calculated by EDX. Photoelectrochemical property of NTN was examined by anodic photocurrent response. Results indicated the photocurrent of NTN was nearly twice as that of non-doped TiO₂ nanotube arrays (TN). Photocatalytic activity of NTN was investigated by degrading dye X-3B under visible light. As a result, 99% of X-3B was decomposed by NTN in 105 min, while that of TN was 59%.     

One-step solvothermal preparation of TiO2/C composites and their visible-light photocatalytic activities

Preparation of anatase type titania nanoparticles and their carbon modification were synchronously achieved by the solvothermal method with glycerol as the carbon source. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and diffuse reflectance spectra (DRS). It was found that the glycerol/ethanol ratio affected significantly the morphology and properties of TiO₂/C composites. The TiO₂/C composite which was obtained in the solution with the glycerol/ethanol ratio of 5/75, contained 1.2 mass% carbon and exhibited both superior adsorption capability and visible-light photocatalytic activity. Contrary to this, samples prepared in the solution with higher glycerol/ethanol ratio, exhibited lower photocatalytic activity similar to that of the titania without carbon modification. It was suggested that excess addition of glycerol might contribute to large amounts of carbonaceous species and severe aggregation of the as-prepared samples, and thus reduced the surface area. As a result, the adsorption capability and visible-light photocatalytic activity increased at first and then decreased with the increase of glycerol addition. Present study provided a facile one-step method to obtain TiO₂/C composites with a controllable carbon content and photocatalytic performance under mild temperature.     

Enhanced photocatalytic activity of TiO2 nano-structured thin film with a silver hierarchical configuration

TiO₂ sol-gels with various Ag/TiO₂ molar ratios from 0 to 0.9% were used to fabricate silver-modified nano-structured TiO₂ thin films using a layer-by-layer dip-coating (LLDC) technique. This technique allows obtaining TiO₂ nano-structured thin films with a silver hierarchical configuration. The coating of pure TiO₂ sol-gel and Ag-modified sol-gel was marked as T and A, respectively. According to the coating order and the nature of the TiO₂ sol-gel, four types of the TiO₂ thin films were constructed, and marked as AT (bottom layer was Ag modified, surface layer was pure TiO₂), TA (bottom layer was pure TiO₂, surface layer was Ag modified), TT (pure TiO₂ thin film) and AA (TiO₂ thin film was uniformly Ag modified). These thin films were characterized by means of linear sweep voltammetry (LSV), X-ray diffraction (XRD), scanning electron microscopy (SEM), electrochemical impedance spectroscopy and transient photocurrent (I_ph). LSV confirmed the existence of Ag⁰ state in the TiO₂ thin film. SEM and XRD experiments indicated that the sizes of the TiO₂ nanoparticles of the resulting films were in the order of TT > AT > TA > AA, suggesting the gradient Ag distribution in the films. The SEM and XRD results also confirmed that Ag had an inhibition effect on the size growth of anatase nanoparticles. Photocatalytic activities of the resulting thin films were also evaluated in the photocatalytic degradation process of methyl orange. The preliminary results demonstrated the sequence of the photocatalytic activity of the resulting films was AT > TA > AA > TT. This suggested that the silver hierarchical configuration can be used to improve the photocatalytic activity of TiO₂ thin film.     

Surface effect of natural zeolite (clinoptilolite) on the photocatalytic activity of TiO2

The surface interaction between TiO₂ and natural zeolite, clinoptilolite, has been investigated by means of transmission electron microscope (TEM), atom force microscope (AFM), X-ray diffractometer (XRD), diffuse reflectance infrared Fourier transform (DRIFT) and far Fourier transform infrared ray (FTIR) spectroscopy. And the photocatalytic degradation (PCD) rate of methyl orange (MO), a model of recalcitrant azo dye, in aqueous system has been measured to compare the photocatalytic activities of different photocatalysts. A model has been carried out to explain the incorporation between TiO₂ particles and natural zeolite. The results show that the TiO₂ particles loaded on zeolite are 50 nm or so, smaller than the pure one, and combine with zeolite via chemical force. Since the reserved adsorption ability and the existence of electron trapper, the TiO₂-zeolite performed more efficient at low initial concentration and in the later period of PCD process, as compared with pure TiO₂ nanopowders.     

Characterization and photocatalytic activity of Zn–TiO2/AC composite photocatalyst

Activated carbon (AC) supported Zn²⁺–TiO₂ photocatalyst was prepared by sol–gel method. The prepared samples were characterized by X-ray diffraction, scanning electron micrograph, nitrogen absorption, diffuse reflectance UV/VIS and X-ray photoelectron spectroscopy. Using toluene as a pollution target, the photocatalytic activity of photocatalyst was evaluated. The results showed that prepared photocatalyst was obviously helpful for the removal of toluene in air. The photocatalytic degradation of toluene by Zn²⁺–TiO₂/AC reached 100% for 40 min and remained 75% after 160 min, while degradation by TiO₂ was only 30%. It indicated that the photocatalytic activity of prepared photocatalyst was enhanced. It is due to Zn²⁺-doping increased the oxidation and reduction of hole–electron pairs, which was the important factor in heterogeneous photocatalysis.     

The enhanced photocatalytic activity of CdS/TiO2 nanocomposites by controlling CdS dispersion on TiO2 nanotubes

CdS/TiO₂ nanocomposites were prepared via a simple wet chemical method, and characterized through X-ray diffraction (XRD) and transmission electron microscopy (TEM). Their ability to degrade Acid Rhodamine B was investigated under visible light irradiation. The results indicate that CdS/TiO₂ nanocomposite with a mass ratio of 4:1(TiO₂:CdS) showed high photocatalytic activity and the CdS loaded on TiO₂ nanotube surface exhibited a hexagonal phase. The dispersion of CdS on TiO₂ nanotube surface had an important effect on the degradation efficiency of pollutant, which provides a strategy for practical industry application.     

Tunable photocatalytic selectivity of fluoropolymer PVDF modified TiO2

Fluoropolymer poly-vinylidene-fluoride modified TiO₂ (PVDF/TiO₂) were prepared via a simple chemisorption approach and characterized by thermo gravimetric analyse, transmission electron microscope, X-ray diffraction, X-ray photoelectron spectroscopy and photoluminescence spectra. The modified mechanism and the photocatalytic selectivity of the PVDF/TiO₂ were studied. The existence of Ti-F coordination bond on the interface between TiO₂ and PVDF was confirmed. For the PVDF modification, the photocatalytic degradation (PCD) of cationic dye was greatly enhanced, and the PCD of anionic dye was obviously inhibited. PVDF/TiO₂ shows high photocatalytic selectivity than that of TiO₂ by degrading mixed solution of cationic dyes MB and anionic dyes MO. The selectivity can be tuned by changing the PVDF modification amount.     

Effects of surface-modification with Bi2O3 on the thermal stability and photoinduced charge property of nanocrystalline anatase TiO2 and its enhanced photocatalytic activity

Bi₂O₃ surface-modified TiO₂ nanoparticle has been synthesized by sol-hydrothermal processes, followed by post-treatment with an appropriate amount of bismuth nitrate solution, and also characterized by XRD, Raman, BET, TEM, FT-IR, XPS, UV-vis DRS and SPS techniques. The effects of the surface-modification with Bi₂O₃ on the thermal stability, photoinduced charge separation and photocatalytic activity for degrading rhodamine B (or phenol) under ultraviolet (or visible) irradiation are investigated in detail, along with their relationships and the activity enhancement mechanisms are also suggested. The results show that the modification with Bi₂O₃ can improve the thermal stability of the as-prepared anatase crystallites, consequently enhancing the anatase crystallinity so as to promote the photoinduced charge separation. And the modification with Bi₂O₃ also extends the optical response range. It can be concluded that the activity enhancement of surface-modified TiO₂ is mainly attributed to the increase in the photoinduced charge separation rate and to the extent of the optical response range, compared with un-modified ones. Moreover, the inhibition phase transformation mechanism related to Bi₂O₃ is suggested.     

Synthesis of TiO2 rutile nanoparticles by PLA in solution

This paper describes the synthesis of TiO₂ nanoparticles by laser ablation in solution synthesis (Lasis). The laser excimer beam passes through a focusing lens and it is sent to the reaction chamber. The frequency used during the synthesis was 20 Hz, intensity 26 kV The metal ablated by the laser beam undergoes an oxidation process resulting from the reaction with water. We obtain TiO₂ nanoparticles with average size of 6.5 nm, crystallized in the rutile structure. The crystallographic and morphological structure was studied by transmission electron microscopy.     

Preparation and characterization of iodine-doped mesoporous TiO2 by hydrothermal method

Iodine-doped mesoporous TiO₂ (I/TiO₂) was prepared by hydrothermal method, using tetrabutyl titanate as precursor, potassium iodate as iodine sources. The as-prepared I/TiO₂ catalysts were characterized by UV-vis, XRD, TEM, BET, TG/DTA, XPS and photoluminescence (PL) spectroscopy. Production of OH radicals on the I/TiO₂ surface was detected by the PL technique using terephthalic acid as a probe molecule. The effects of hydrothermal reaction temperature, calcination temperature and iodine doping content on the structure and properties of the catalysts were investigated. The results showed that iodine-doped TiO₂ calcinated at 300 °C have good anatase crystal. The optimal hydrothermal conditions have been determined to be that reaction temperature 120 °C, calcinated temperature 300 °C and added 1.16 mmol iodine dopants. The average particle size of I/TiO₂ synthesized under optimal condition (I-3 sample) is about 3.9 nm. The I-3 photocatalyst contains 100% anatase crystalline phase of TiO₂. BET specific surface area of I-3 sample is184.8 m² g⁻¹ and is 3.67 times that of pure TiO₂ (50.37 m² g⁻¹). Iodine in I/TiO₂ catalyst mainly exists in the form of I₂, and photoactivity of I/TiO₂ catalyst in visible light comes from photosensitize of I₂. I/TiO₂ catalysis shows very high efficiency for the degradation of phenol under visible light.     

Synthesis and photocatalytic properties of porous TiO2 films prepared by ODA/sol-gel method

Porous TiO₂ films were deposited on SiO₂ pre-coated glass-slides by sol-gel method using octadecylamine (ODA) as template. The amount of ODA in the sol played an important role on the physicochemical properties and photocatalytic performance of the TiO₂ films. The films prepared at different conditions were all composed of anatase titanium dioxide crystals, and TiO₂ crystalline size got larger with increasing ODA amount. The maximum specific surface area of 41.5 m²/g was obtained for TiO₂ powders prepared from titanium sol containing 2.0 g ODA. Methyl orange degradation rate was enhanced along with increasing ODA amount and reached the maximal value at 2.0 g addition of ODA. After 40 min of UV-light irradiation, methyl orange degradation rate reached 30.5% on the porous film, which was about 10% higher than that on the smooth film. Porous TiO₂ film showed almost constant activity with slight decrease from 30.5% to 28.5% after 4 times of recycles.     

Uniform thin films of TiO2 nanoparticles deposited by matrix-assisted pulsed laser evaporation

We report morphological and optical properties of a colloidal TiO₂ nanoparticle film, deposited on a quartz substrate by using the Matrix-Assisted Pulsed Laser Evaporation (MAPLE) technique. Atomic Force Microscopy demonstrated that a good uniformity of the deposition can be obtained. The presence of agglomerates with dimensions of about 1 μm in size was noticed. Form UV-vis transmission spectra, recorded in the 200-800 nm range, the optical constants and the energy gap were determined besides the film thickness. The optical constants resulted in agreement with the values reported in literature for TiO₂ nanoparticle thin films.     

Photocatalysis and wave-absorbing properties of polyaniline/TiO2 microbelts composite by in situ polymerization method

Polyaniline (PANI)/TiO₂ composite is prepared by in situ polymerization of polyaniline on the surface of TiO₂ template obtained by the sol-gel process via cotton template. The TiO₂ microbelts are prepared by sol-gel method using the absorbent cotton as template for the first time. Then the TiO₂ microtubules are used as template for the preparation of polyaniline/TiO₂ composites. The structure, morphology and properties of the composites are characterized with scanning electron microscope (SEM), IR, Net-wok Analyzer. A possible formation mechanism of TiO₂ microtubules and polyaniline/TiO₂ composites has been proposed. The effect of the mol ratio of polyaniline/TiO₂ on the microwave loss properties and photocatalysis properties of the composites is investigated.     

Mechanism of enhanced photocatalysis of TiO2 by Fe in suspensions

In this work, the mechanism of enhanced photocatalysis of TiO₂ with Fe³⁺ was studied using Sulfadiazine (SD) as the model compound. Results indicated that degradation rate of SD was enhanced by the addition of Fe³⁺ in TiO₂ suspension. The crystalline structure of TiO₂ particles was stable in suspensions. The hydroxyl radical generated by TiO₂/Fe³⁺ (both TiO₂ and Fe³⁺) photocatalysis was in a higher yield. Moreover, Fe²⁺ was found not to give an obvious impact on the SD degradation in TiO₂ suspension, whereas Fe³⁺ had a notable effect. The adsorption amount of TiO₂ was greatly enhanced by the addition of Fe³⁺ in suspensions. Finally, an interaction model of SD degradation in TiO₂ suspension containing Fe³⁺ was also proposed by investigating of surface behaviors of TiO₂ particles. It will be beneficial to use Fe³⁺ as the electron acceptors on the surface of TiO₂ particles, which helps to improve the yield of hydroxyl radical.     

Light-induced antifungal activity of TiO2 nanoparticles/ZnO nanowires

Antifungal activity of TiO₂/ZnO nanostructures under visible light irradiation was investigated. A simple chemical method was used to synthesize ZnO nanowires. Zinc acetate dihydrate, Polyvinyl Pyrrolidone and deionized water were used as precursor, capping and solvent, respectively. TiO₂ nanoparticles were deposited on ZnO nanowires using an atmospheric pressure chemical vapor deposition system. X-ray diffraction pattern of TiO₂/ZnO nano-composite has represented the diffraction peaks relating to the crystal planes of the TiO₂ (anatase and rutile) and ZnO. TiO₂/ZnO nanostructure antifungal effect on Candida albicans biofilms was studied and compared with the activity of TiO₂ nanoparticles and ZnO nanowires. The high efficiency photocatalytic activity of TiO₂ nanoparticles leads to increased antifungal activity of ZnO nanowires. Scanning electron microscope was utilized to study the morphology of the as prepared nanostructures and the degradation of the yeast.