On some new effect of laser ray propagation in atmospherik air

The laser beam space uncertainty σ was measured during ray propagation in atmospheric air (a) and in atmospheric air inside the tube (t) with both ends closed by optically transparent windows. For the studied case of the 70 m passed distance, the sigma values were discovered to differ greatly: σ _a /σ _t ≈ 100 ^x . The observed effect may represent a physical basis for the creation of an extended laser ray to be used as a coordinate axis in the high-precision metrology when assembling a big-length research equipment (accelerators, detectors, etc.) or in civil engineering tasks.     

Observation of specific features of laser beam propagation in air with standing acoustic waves

The process of laser beam propagation in air with a standing acoustic wave is studied. The uncertainty σ in the spatial localization of the laser beam is found to decrease in this process. In the studied case of laser beam propagation in a tube at atmospheric air pressure, the observed effect is manifested as a decrease in σ alongside the increasing resonator (tube) quality factor.     

Long-wavelength MBE grown GaInNAs quantum well laser emitting at 1270 nm

In this paper, we report on comprehensive theoretical optical properties analysis and experimental device electrical-optical characterization of long wavelength GaInNAs edge-emitting laser diode. The theoretical analysis demonstrates that a high quality GaInNAs active region and device design are devised, where high material gain near 1.3 μm and optimal optical mode confinement are calculated. Experimentally, room temperature lasing emission around 1.27 μm with threshold current densities of 670–810 A/cm² is obtained from the fabricated broad area GaInNAs edge-emitting laser grown by molecular beam epitaxy technique.     

Experiment to measure the Lamb shift in muonic hydrogen

The contribution of the root mean square (RMS) proton charge radius to the Lamb shift (2S–2P energy difference) in muonic hydrogen (μp) amounts to 2%. Apart from the uncertainty on this charge radius, theory predicts the Lamb shift with a precision on the ppm level. We are going to measure ΔE (2 S_1/2(F=1)–2 P_3/2(F=2)) in a laser resonance experiment to a precision of 30 ppm (i.e., 10% of the natural linewidth) and to deduce the RMS proton charge radius with 10⁻³ relative accuracy, 20 times more precise than presently known. The most important requirement for the feasibility of such an experiment, namely the availability of a sufficient amount of long lived metastable μp atoms in the 2S state, has been investigated in a recent experiment at PSI. Our analysis shows that in the order of one percent of all muons stopped in low pressure hydrogen gas form a long lived μp(2S) with a lifetime of the order of 1 μs. The technical realization of our experiment involves a new high intensity low energy muon beam, an efficient low energy muon entrance detector, a randomly triggered 3 stage laser system providing the 0.5 mJ, 7 ns laser pulses at 6.02 μm wavelength, and a combination of a xenon gas proportional scintillation chamber (GPSC) and a microstrip gas chamber (MSGC) with a CsI coated surface to detect the 2 keV X rays from theμp(2P → 1S) transition. This revised version was published online in August 2006 with corrections to the Cover Date.     

Online monitoring of ethane traces in exhaled breath with a difference frequency generation spectrometer

We report a transportable mid-infrared laser cavity leak-out spectrometer for online detection of trace gases. The laser spectrometer is based on continuous-wave difference-frequency generation in the wavelength region around 3 μm. Sensitive spectroscopic trace gas monitoring was achieved using a high-finesse ring-down cavity. For difference-frequency generation, we use a periodically poled lithium niobate (PPLN) crystal, pumped by a Nd:YAG laser (signal wave) and a diode laser (pump wave) with a tapered amplifier. A maximum power of 280 μW near λ=3.3 μm is achieved using a pump power of 180 mW at 807 nm, a signal power of 890 mW at 1064.46 nm, and a 50-mm-long PPLN crystal. The resulting system proved to be a unique tool with high sensitivity and specificity for rapid and precise breath testing. We demonstrate spectroscopic online monitoring of ethane traces in exhaled human breath with a precision of 270 parts per trillion (1σ) and a time resolution of 1 s. PACS 42.62.Be; 42.60.-v; 07.57.Ty     

The Muonic Hydrogen Lamb Shift Experiment at PSI

A measurement of the 2S Lamb shift in muonic hydrogen (μ⁻p) is being prepared at the Paul Scherrer Institute (PSI). The goal of the experiment is to measure the energy difference ΔE(2⁵ P _3/2−2³ S _1/2) by laser spectroscopy (λ≈6μm) to a precision of 30 ppm and to deduce the root mean square (rms) proton charge radius with 10⁻³ relative accuracy, 20 times more precise than presently known. An important prerequisite to this experiment is the availability of long-lived μp_2S -atoms. A 2S-lifetime of ∼1 μs – sufficiently long to perform the laser experiment – at H₂ gas pressures of 1–2 hPa was deduced from recent measurements of the collisional 2S-quenching rate. A new low-energy negative muon beam yields an order of magnitude more muon stops in a small low-density gas volume than a conventional cloud muon beam. A stack of ultra-thin carbon foils is the key element of a fast detector for keV-muons. The development of a 2 keV X-ray detector and a 3-stage laser system providing 0.5 mJ laser pulses at 6 μm is on the way. This revised version was published online in August 2006 with corrections to the Cover Date.     

Planarity and stability of shock driven directly by the ninth laser beam from “Shenguang-II" laser facility

Using the ninth laser beam (converted to 2ω) of “Shenguang-II” laser facility and the beam smoothing technology of lens-array [Appl. Opt. 25, 377 (1986); Phys. Plasmas. 9, 3201 (1995)], a shock wave with 700 μm (the root-mean-square of shock breakout time (RMS) RMS ≈ 6.32 ps) flat top was created. An Al-Al four-step target was designed to do research on shock wave stability in an Al target. And the shock stability experiment with the Al-Al four-step target indicated that the shock wave steadily propagated in the Al target of thickness of about 20–45 μm under the power density of ~ 1.0×10¹⁴ W/cm².     

Absolute cross section of p(<Superscript>7</Superscript>Be,γ)<Superscript>8</Superscript>B using a novel approach

The absolute cross section σ (E) of the radiative capture reaction p(⁷Be,γ)⁸B at the center-of-mass energy E = 992 keV has been measured using a radioactive ⁷Be ion beam and a windowless gas target system filled with H₂ gas. The ⁸B residual nuclides were detected with a recoil separator consisting of momentum and velocity filters and a ΔE-E detector telescope. The ⁸B yield was observed concurrently with the ⁷Be + p elastic scattering yield, relating σ(E) to the Rutherford scattering cross section. The resulting value, σ(E) = 0.41 ± 0.11 μb, leads to an S(E) factor at zero energy of S(0) = 16 ± 4 eV b, in fair agreement with recommended values. Received: 8 February 2000     

Cooling rate dependence of undercooling of pure Sn single drop by fast scanning calorimetry

An energy source produced by a TEA CO₂ laser operated at 10.6 μm primarily was considered as a key essential in this paper to describe the energy conversion process in air-breathing laser propulsion in the round. Some secondary factors were ignored when three independent modules, a ray transmission module, an energy source term module and a fluid mechanics module, were established by a simultaneous laser radiation transportation equation and a fluid mechanics equation set-up. The incident laser beam after being reflected by the optical system or transmitted by it was simulated based on a certain geometrical optics method named ray tracing. Thus, coherent superimposition could be avoided when describing the laser beam focusing process, and so could the solving process of the laser wave equation at the non-paraxial condition. The calculated results were in good agreement with those of theoretical analysis and experiments.     

Mid-infrared laser spectroscopic determination of isotope ratios of N2O at trace levels using wavelength modulation and balanced path length detection

We present a new mid-infrared laser spectrometer for high-precision measurements of isotopic ratios of molecules at ppm concentrations. Results are discussed for nitrous oxide (N₂O), where a precision of 3‰ for a single measurement and a reproducibility of 6‰ have been achieved for a concentration of 825 ppm. The room-temperature laser source employed is based on difference-frequency generation delivering a continuous-wave power up to 23 μW at wavelengths between 4.3 μm and 4.7 μm and a line width of 1 MHz. Two different measurement methods are compared; wavelength modulation with first-harmonic detection and direct absorption spectroscopy by recording the spectrum with a data-acquisition card. Two different detection schemes were employed; either all isotopomers were measured using the long path (36 m) of the multipass cell or a balanced path length detection scheme was used, where the main isotope was measured with a beam along a shorter path (40 cm) in the multipass cell. A single-pass reference cell was designed, offering two different path lengths for balanced path length detection. All combinations of measurement methods and detection schemes were tested regarding precision of a single measurement and long-term stability. The advantages and disadvantages of various measurement approaches are discussed. PACS 42.62.Fi; 42.65.Ky; 32.10.Bi     

Intense laser flux effects on GaAs

Surface damage measurements on GaAs for pulsed laser flux at 0.694 μm, 1.06 μm, and 10.6 μm are presented. The damage threshold is seen to increase with the flux wavelength and decrease with increasing pulse duration. Other experiments were performed which indicated that the initial effect of the laser beam is to produce expansion of the bulk material and that the interband Faraday rotation at 1.06 μm is not dependent on laser intensity.     

Study of the conditions for the effective energy transfer in a process of acceleration and collision of the thin metal disks with the massive target

Efficiency studies of laser driven thin metal disks acceleration using the first harmonic (λ₁=1.315 μm) of the Prague Asterix Laser System (PALS) and subsequent craters creation produced by collisions of these disks with massive targets are presented. Several different disks made of aluminium and copper foils with diameters of 300 μm and 600 μm and thicknesses of 11 μm (Al) and 3.6 μ m (Cu) were employed. Disks were placed at the distance of either 100 μ m or 300 μm in front of aluminium massive targets. The following irradiation conditions were used: the laser beam energy of 120 J, the focal spot diameter of 200 μm, and the pulse duration of 0.4 ns (FWHM). A three-frame interferometric system was employed to determine electron density distributions in plasma corona. Shape and volume of craters were obtained by crater replica technology and microscopy measurements. The aim of these investigations was to analyse conditions leading to the most effective energy transfer in the process of collision of the accelerated disks with solid targets. The overall efficiency of these processes was characterized by the volume of craters produced in such targets.     

Telecom-grade fiber laser-based difference-frequency generation and ppb-level detection of benzene vapor in air around 3 μm

We report on the development of a field deployable compact laser instrument tunable over ∼232 cm⁻¹ from 3.16 to 3.41 μm (2932.5–3164.5 cm⁻¹) for chemical species monitoring at the ppb-level. The laser instrument is based on widely tunable continuous-wave difference-frequency generation (DFG), pumped by two telecom-grade fiber lasers. DFG power of ∼0.3 mW near 3.3 μm with a spectral purity of ∼3.3 MHz was achieved by using moderate pumping powers: 408 mW at 1062 nm and 636 mW at 1570 nm. Spectroscopic performance of the developed DFG-based instrument was evaluated with direct absorption spectra of ethylene at 3.23 μm (∼3094.31 cm⁻¹). Absorption spectra of vapor-phase benzene near 3.28 μm (∼3043.82 cm⁻¹) were recorded with Doppler-limited resolution. Line intensities of the most intense absorption lines of the ν ₁₂ band near 3043.8 cm⁻¹ were determined to support development of sensitive mid-infrared trace gas detection of benzene vapor in the atmosphere. Detection of benzene vapor in air at different concentration levels has been performed for the first time using multi-pass cell enhanced direct absorption spectroscopy at ∼3.28 μm with a minimum detectable concentration of 50 ppb (1σ).     

Saturable absorbers for passive Q-switching of erbium lasers emitting in the region of 3 μm

The phototropic properties of Fe:ZnSe, Co:ZnSe, and Co:ZnS single crystals have been investigated. It is shown that these crystals can be used to advantage as the saturable absorbers in solid-state erbium lasers emitting in the region of the 3-μm range. The absorption cross sections of the ground states of the Co²⁺ ion in the ZnSe (σ_GSA = 11·10⁻²⁰ cm²) and ZnS (σ_GSA = 5.6·10⁻²⁰ cm²) crystals and of the Fe²⁺ ion in the ZnSe (σ_GSA = 50·10⁻²⁰ cm²) crystal at λ = 2.79 μm were determined experimentally. It has been established that the above-indicated crystals in the excited state absorb light weakly. The use of these crystals as passive Q switches made it possible to realize, for the first time, the regime of Q-switching of a Cr,Er:YSGG laser emitting at a wavelength of 2.79 μm. Single pulses with an energy of 60 mJ and a duration of 170 nsec were obtained in the regime of passive Q-switching. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 72, No. 6, pp. 747–751, November–December, 2005.     

Optical vortex beams for trapping and transport of particles in air

In this paper we show that laser beams containing phase singularity can be used for trapping and guiding light-absorbing particles in air. The experiments were performed with agglomerates of carbon nanoparticles with the size in the range 0.1–10 μm; the typical cw laser power was of a few mW. The stability of open-air three-dimensional trapping was within ±2 μm in both the transverse and the longitudinal directions. The particle position on the beams axis within the trap can be controlled by changing the relative intensity of two beams. The distinguishing feature of the trapping strategy is that particles are trapped at the intensity minimum of the beam, thus with minimum heating and intervention into the particle properties, which is important for direct studies of particle properties and for air-trapping of living cells.     

A Raman laser system for multi-wavelength satellite laser ranging

~~A Raman laser system for multi-wavelength satellite laser ranging@K.Hamal$Czech Technical University in Prague,Czech @I.Prochazka$Czech Technical University in Prague,Czech @J.Blazej$Czech Technical University in Prague,Czech1. Yang Fumin, Chen Wanzhen, Zhang Zhongping et al., Satellite laser ranging experiment with sub-centimeter single-shot ranging precision at Shanghai Observatory, Science in China, Ser. A, 2002, 32(10): 935-939. 2. Degnan, J. J., Millimeter accurac…     

Smoothing of laser energy deposition by gas jets

Smoothing of laser beam non-uniformities using gas jets has been studied. The experiment has been performed with the PALS laser working at 0.44 μm with an intensity of about 10¹⁵ W/cm². The laser beam has been split in two by a prism thus creating an artificial large-scale non-uniformity (≈90 μm). We recorded time resolved and static images of laser-gas jet interaction with and without an Al target. Multi 1D and 2D simulations show that such interaction acts redistributing the over-intensities over larger surface. This effect has to be attributed to ionization processes with consequent laser beam refraction. Results show that Argon gas jet produces a strong refraction of the laser beam thus strongly reducing the initial two spots separation.     

Antireflection structures written by excimer laser on CVD diamond

Two-dimensional antireflective periodical microstructures for the IR range are fabricated on the surface of CVD diamond films. These structures are created using an ArF excimer laser (λ=193 nm) and a direct writing scheme consisting of a beam collimator and a microscope objective to focus the beam onto the sample. Two different arrays are investigated. One has a spacing of 3 μm and is produced with single shots and the other one has a spacing of 4 μm and is produced with three shots per spot. The hole depth and shape are measured with an atomic force microscope (AFM). The optical transmittance and the scattering properties of the structure at 10.6 μm are reported for a CO₂ laser beam. With a spectrometer further transmission measurements in the range of 5 to 20 μm are performed. Received: 16 September 1999 / Accepted: 11 October 1999 / Published online: 24 March 2000     

Ring beam shaping optics fabricated with ultra-precision cutting for YAG laser processing

In this study, a method for generating ring intensity distribution at a refraction-type lens with an aspheric element was proposed, and the beam shaping optical element was finished using only ultra-precision cutting. The shape of the optical element and its irradiance pattern were determined from numerical calculation based on its geometrical and physical optics. An ultra-precision lathe was employed to fabricate beam shaping optical elements, and acrylic resin was used as the material. The transmittance of an optical element (a rotationally symmetrical body) with an aspheric surface fabricated using a single-crystal diamond tool was over 98%, and its surface roughness was 9.6 nm Ra. The method enabled the formation of a circular melting zone on a piece of stainless steel with a thickness of 300 μm through pulse YAG laser (λ 1:06 μm) processing such that the average radius was 610 μm and the width was 100–200 μm. Circular processing using a ring beam shaping optical element can be realized by single-pulse beam irradiation without beam scanning.