水下吸声覆盖层声管测试的背衬研究

在吸声覆盖层水声声管测试的实验研究中，覆盖层背衬的选择对测量结果有重大影响。在我们二维理论研究的基础上，建立了吸声覆盖层声学特性的传递函数模型，分析比较了不同背衬对吸声覆盖层声学性能的影响。结果表明，不同背衬对吸声覆盖层吸声性能的影响具有明显不同的特性。背衬为双层壳体时，水层对吸声覆盖层的吸声系数曲线有明显的调制现象。背衬为单层壳体或双层壳体时，从整体上讲，吸声系数更趋近于刚性背衬而非软背衬的情况。在实验室小样品声管测试中，以较厚的钢柱作为背衬的测试数据来衡量吸声覆盖层性能更为合适，且易于实现。     

Analysis of absorption performances of anechoic layers with steel plate backing

Rubber layers with air-filled cavities or local resonance scatters can be used as anechoic coatings. A lot of researches have focused on the absorption mechanism of the anechoic coatings. As the anechoic coatings are bonded to the hull of submarine, the vibration of the hull should not be neglected when the analysis of the absorption characters is carried out. Therefore, it is more reasonable to treat the anechoic coating and the backing as a whole when the acoustic performance is analyzed. Considering the effects of the steel plate backing, the sound absorption performances on different models of anechoic coatings are investigated in this paper. The Finite Element Method is used to illustrate the vibrational behaviors of the anechoic coatings under the steel backings by which the displacement contours is obtained for analysis. The theoretical results show that an absorption peak is induced by the resonance of the steel slab and rubber layer. At the frequency of this absorption peak, the steel plate and the coating vibrates longitudinally like a mass-spring system in which the steel slab serves for mass and the coating layer is the spring. To illuminate the effects of the steel slab backing on the acoustic absorption, the thicknesses of the steel slab and the anechoic layer are discussed. Finally, an experiment is performed and the results show a good agreement with the theoretical analysis.     

含空腔的功能梯度声学覆盖层水下吸声特性

针对传统的声学覆盖层吸声频带窄的问题,基于功能梯度材料的特点提出了一种含空腔结构的水下功能梯度声学覆盖层结构,引入梯度有限元法建立了功能梯度型声学覆盖层的水下声学计算模型,研究了功能梯度声学覆盖层结构的水下吸声特性。与传统的功能梯度结构声学建模方法相比,在保证计算精度和计算效率的基础上,文中所建立的功能梯度结构声学计算模型可适用于更复杂的功能梯度声学结构声学性能评估。研究结果表明,功能梯度声学覆盖层能够有效改善中高频段的吸声性能,获得较好的宽频吸声效果。此外,空腔形状采用锥型空腔结构或者组合型空腔结构可以有效地拓宽功能梯度声学覆盖层的吸声频带。     

不锈钢表面激光熔覆层与喷焊层耐磨性对比研究

本文研究在１Ｃｒ１８Ｎｉ９Ｔｉ基体上采用激光熔覆和离子喷焊二种工艺形成的涂层对耐磨性的影响。使用５ｋＷ横流ＣＯ２激光器对预置在基体上的Ｃｏ基自熔合金粉末进行单道或多道扫描，得到的熔层与等离子焊层对比结果是：激光熔层缺陷率低，成品率高，其结构致密均匀，晶粒细小，成分稀释率更小，对基体热影响小，熔层硬度与强韧性更高。性能试验证明：激光熔层具有更高的抗擦伤磨损和抗冲击滑动高温磨损性能，耐磨性提高了一倍左右。     

Correlation between the isoelectric point of solid surfaces of metal oxides and X-ray photoelectron spectroscopy chemical shifts

The isoelectric point of solid surfaces (IEPS) is an important parameter characterizing the acid—base and adhesion behaviour of oxide surfaces. A satisfactory correlation is obtained between the sum of the metal and oxygen X-ray photoelectron spectroscopy chemical shifts and the IEPS for some anhydrous oxide surfaces. This shows that the overall acid—base behaviour of the surface results from the competition between the acidity of the cation and the basicity of oxygen.     

Acoustic anechoic layers with singly periodic array of scatterers: Computational methods,absorption mechanisms,and optimal design

The acoustic properties of anechoic layers with a singly periodic array of cylindrical scatterers are investigated. A method combined plane wave expansion and finite element analysis is extended for out-of-plane incidence. The reflection characteristics of the anechoic layers with cavities and locally resonant scatterers are discussed. The backing is a steel plate followed by an air half space. Under this approximate zero transmission backing condition, the reflection reduction is induced by the absorption enhancement. The absorption mechanism is explained by the scattering/absorption cross section of the isolated scatterer. Three types of resonant modes which can induce efficient absorption are revealed. Due to the fact that the frequencies of the resonant modes are related to the size of the scatterers, anechoic layers with scatterers of mixed size can broaden the absorption band. A genetic optimization algorithm is adopted to design the anechoic layer with scatterers of mixed size at a desired frequency band from 2 kHz to l0 kHz for normal incidence, and the influence of the incident angle is also discussed.     

基于等效参数反演的敷设声学覆盖层的水下圆柱壳体声散射研究

应用了一种等效方法计算敷设声学覆盖层无限长圆柱壳体水下声散射特性.等效方法的核心是忽略复杂声学覆盖层内部的声学结构,将其作为具有等效材料参数的均匀阻尼层进行建模,该均匀阻尼层具有和原覆盖层相同的复反射系数.进而,应用COMSOL Multiphysics软件建立敷设均匀阻尼层圆柱壳体的有限元模型并求解其声散射特性.等效方法的关键是等效材料参数的获取.采用充水阻抗管实验和有限元数值实验两种方法获取声学覆盖层贴敷在与壳体具有相同厚度、相同材料背衬条件下的复反射系数,在此基础上,基于遗传算法反演材料的等效参数.研究表明,等效参数具有频变特性,且尽管等效杨氏模量和等效泊松比在频率范围内存在较大波动,但是等效前后复反射系数仍保持一致.为了验证等效方法求解壳体声散射特性的准确性,同时建立了敷设声学覆盖层壳体的完整有限元模型,将覆盖层内部声学结构进行精细建模,并求其声散射特性.结果表明,两种方法求得的形态函数符合得较好,在整个频率范围内平均误差大约为1 d B.     

含有周期球腔的黏弹性覆盖层消声性能分析

利用散射矩阵法分析了单个球状空腔在黏弹性橡胶中的Mie散射特性以及振动模式.以此为基础，利用多重散射法分析了不同背衬条件下，含有单层周期球状空腔的橡胶覆盖层(厚度为8mm)的消声性能.结果表明，单个球腔的径向共振对覆盖层的低频消声性能有重要贡献，覆盖薄层在共振区具有良好的消声性能.最后，设计了双层消声覆盖层(厚度为20mm)，有效拓展了消声带宽. 关键词： Mie散射 多重散射法 消声材料 声子晶体     

Plunging method for Nd : YAG laser cladding with wire feeding

The effects of wire feeding direction and position, cladding time, and cladding speed on the quality of cladding layer for laser cladding with wire feeding are studied. Experiment results indicate that the wire feeding direction and position are important for wire laser cladding. By adopting the correct wire feeding direction and position, the wire can be plunged into the melt pool and can be melted by the heat of the molten metal. With the increase of cladding speed, the dilution of clad layer can be reduced and the growth of the grain size of heat-affected zone of the base metal can be limited. If proper cladding parameters are used, the clad layers will have a good surface shape, sound metallurgical bonding with base metal, low dilution, and the effect of heating on heat-affected zone metal can be limited. The hardness of the clad layer and heat-affected zone are checked. It indicates that with the increase of cladding speed, the hardness of the clad layer and heat-affected zone increases.     

低活化马氏体钢热等静压焊接接头性能初步研究

研究了低活化马氏体钢(CLF-1)热等静压(HIP)焊接接头的性能,经980℃/1h/空冷+740℃/2h/空冷的性能热处理后,接头组织保持着CLF-1钢母材回火马氏体组织;常温拉伸性能与母材相当,断口为韧窝状且有第二相粒子产生,为塑性断裂且断于焊缝;常温冲击功最高为母材的26.2%。初步分析认为焊接表面制备状态、表面污染物、表面清洗状态、表面氧化膜都会影响基体原子充分扩散,导致界面扩散层不均匀,焊缝裂纹敏感性增强,冲击功低,且不稳定。     

水下目标高分辨方位估计特征分解法的C30硬件实验研究

高分辨方位估计特征分解法是一类性能良好的方法，本文从水下阵列信号处理的实际应用出发，对这类方法进行了C30硬件实验研究，所得结果为高分辨技术的实际应用提供了重要依据文中构造了高分辨方位估计的C30硬件实验系统；并实现了高分辨方位估计的Pisarenko法、MUSIC法、Johnson法和最小摸（Mininorm）法；对高分辨实验系统进行了仿真实验和消声水池实验，并测试了各特征分解法的运行时间．结果表明，高分辨C30实验系统表现了良好的方位估计统计性能和实时性能     

Wear resistance of laser cladding and plasma spray welding layer on stainless steel surface

The effect of coatings, which are formed with laser cladding and plasma spray welding on 1Cr18Ni9Ti base metal, on wear resistance is studied, A 5-kW transverse flowing CO2 laser is used for cladding Co base alloy powder pre-placed on the substrate. Comparing with the plasma spray coatings, the spoiled rate of products with laser clad layers was lower and the rate of finished products was higher. Their microstructure is extremely fine. They have close texture and small size grain. Their dilution resulting from the compositions of the base metal and thermal effect on base metal are less. The hardness, toughness,and strength of the laser cladding layers are higher. Wear tests show that the laser layers have higher properties of anti-friction, anti-scour and high-temperature sliding strike. The wear resistance of laser clad layers are about one time higher than that of plasma spray welding layer.     

覆黏弹层加肋双层板的声反射

为评估覆盖层的吸声性能,研究黏弹层在无限大周期加肋双层板背衬下的声反射。首先通过弯曲波与Lamb波的比较,揭示了板近似理论不适用于黏弹性板的原因。为此采用(黏)弹性理论处理(黏)弹性板,而肋板的处理则采用板近似理论,并用Hull提出的方法解决肋板和平板的耦合问题,得到反射声场的解。与板近似理论计算加肋双层板声反射的结果进行比较验证了本文方法的正确性,对反射系数进行计算分析了背衬对声反射的影响,定义平均反射系数比较了不同覆盖层的性能。结果表明,频率较低时覆盖层无法有效抑制背衬的影响,板间流体层与双层板的耦合作用引起共振散射,肋板与双层板的耦合作用降低声反射。     

Metallic spherical anechoic chamber for antenna pattern measurement

Anechoic chambers are used for indoor antenna measurements. The common method of constructing an anechoic chamber is to cover all inside walls by the electromagnetic absorbers. In this paper, a fully metallic spherical chamber structure is presented in which the propagation of the electromagnetic waves inside the chamber is controlled and they are guided to an absorber. In the proposed method, an appropriate quiet zone is obtained, and unlike ordinary anechoic chambers, the absorber usage amount is reduced greatly. The performance of the chamber is evaluated by simulation. The results show that the proposed method could provide a useful technique for the indoor antenna measurements.     

Application of multi-layered polyurethane foams for flat-walled anechoic linings

Previous work demonstrated that a multi-objective evolutionary algorithm could be successfully employed as an optimiser to make the design of flat-walled multi-layered anechoic linings more efficient. In the present work, such an algorithm is employed to investigate the practical aspects of the application of multi-layered polyurethane foams as the flat-walled anechoic lining. The investigation includes aspects such as the efficacy of a single layer of material, the minimum number of layers of linings to achieve the minimum overall thickness for low (100 Hz), mid (250 Hz) and high (500 Hz) cut-off frequencies, the use of the three-layered lining composite for low to mid cut-off frequencies and the effect of air gaps.     

Tri-component phononic crystals for underwater anechoic coatings

Localized resonance in phononic crystal, composed of three-dimensional arrays of composite units, has been discovered recently. The composite unit is a high-density sphere coated by soft silicon rubber. In this Letter, the absorptive properties induced by the localized resonance are systemically investigated. The mode conversions during the Mie scattering of a single coated lead sphere in unbounded epoxy are analyzed by referring the elements of the scattering matrix. Then the anechoic properties of a slab containing a plane of such composite scatterers are investigated with the multiple-scattering method by accounting the effects of the multiple scattering and the viscous dissipation. The results show that the longitudinal to transverse mode conversion nearby the locally resonant region is an effective way to enhance the anechoic performance of the finite slab of phononic crystal. Then, the influences of the viscoelasticity of the silicon rubber and the coating thickness on the acoustic properties of the finite slab are investigated for anechoic optimization. Finally, we synthetically consider the destructive scattering in the finite slab of phononic crystal and the backing, and design an anechoic slab composed of bi-layer coated spheres. The results show that the most of the incident energy is absorbed at the desired frequency band.     

316L������ھ�̬Һ̬��еĸ�ʴ��Ϊ�о�

利用脉冲激光诱导击穿光谱仪(LIBS)结合SEM、EDX和维氏硬度(HV)等分析手段,分析了316L不锈钢在350℃的液态锂中静态腐蚀500h后的腐蚀特性.微观形貌分析表明:样品存在较明显的晶间腐蚀,其腐蚀层厚度约为2.7μm.硬度分析表明:腐蚀后表面硬度值约HV234.72,约是腐蚀前硬度值的0.78倍.LIBS组分分析表明:经液态锂腐蚀后的样品表面Ni、Cr等元素含量相对减少;在被腐蚀区域Li元素含量随激光击打深度的增加而减少,而Ni、Cr等元素含量与之近似呈成正比递增;母材区Li元素的渗透深度约3.5μm,约是焊缝区的0.6倍.     

Acoustic reflection of rib-stiffened double plates coated with a viscoelastic layer

To predict sound-absorbing performance of anechoic materials,the acoustic reflection problem of a viscoelastic layer backed with periodically rib-stiffened infinite double plates is studied in this paper.The reason why structural theories of plates are not applicable to viscoelastic plates is explained through comparing dispersion and attenuation curves of flexural waves with those of Lamb waves.As a result,（visco-）elastic theory is adopted to deal with（visco-）elastic plates,and ribs are treated by structural theories of plates.The coupling between ribs and plates are solved by Hull＇s method,and solution of the reflected field is obtained.The accuracy of present method is validated by comparing with the results by the structural theories of plates.The influence of a backing on the acoustic reflection of the viscoelatic layer is analyzed by computing reflection coefficients.Performances of different viscoelastic materials are evaluated by the average reflection coefficients.The computational results show that,influence of a backing on the acoustic reflection cannot be suppressed by the viscoelastic materials in low frequencies.The resonance is determined by the coupling of the fluid layer and the double plates.And ribs,which are coupled with the double plates,mainly reduce the acoustic reflection.     

Transverse magnetic peak type metal-clad optical waveguide sensor

Transverse magnetic (TM) waves in a four-layer slab waveguide structure are studied for optical sensing applications. The structure consists of a semi-infinite substrate, a thin metal layer, a medium with negative permittivity and permeability as a guiding layer, and a semi-infinite layer as a cover. The proposed sensor is operated in reflection mode in which the angular position of the reflectance peak is used to detect small changes in the refractive index of the cover medium. The optimal structure parameters that correspond to the sharpest and highest peak are presented. The results reveal that for aluminum metal layer, a thickness of about 9 nm represents the optimum metal thickness. Moreover, the thickness, negative permittivity, and negative permeability of the guiding layer are found to have great impacts on the performance of the proposed optical waveguide sensor.     

Structure and surface composition of solar selective graded stainless steel/carbon cermet films

The composition of a reactively sputtered graded stainless steel/carbon cermet with a copper base layer has been studied using Auger electron spectroscopy/argon ion depth profiling and X-ray photoelectron spectroscopy. The interlayer structure of newly deposited films is independent of the underlying substrate but exhibits strong substrate interactions following baking at 670K for 60 min. Similar behaviour is found in films aged in air at room temperature over a period of months. Metal oxide substrates are most reactive, causing oxidation within the film. This type of multilayer cermet is used in solar collectors as a spectrally selective film. The implications of these findings for the long term integrity and performance of the thermal solar collectors are discussed.