Hardware modification of a 7 mm MAS NMR probe to a single-crystal goniometer

Tensorial terms of the Hamiltonian can be measured by solid-state single-crystal nuclear magnetic resonance (NMR) spectroscopy which requires a goniometer NMR probehead. Goniometer probes; however, are not standard parts of solid NMR spectrometers and are available only at a much higher price than magic-angle spinning (MAS) probeheads widely used in research. Due to requirements of MAS experiments, modern probeheads are designed for small ceramic rotors, which are 1-4 mm in diameter, to reach very high angular frequencies, so there are several older 7 mm MAS probeheads used rarely todays in NMR laboratories. In this paper, a simple method is presented how to rebuild step-by-step a 7 mm Bruker MAS probehead to be suitable for single-crystal spectroscopy. In the second part (31)P chemical shift tensors of Na(4)P(2)O(7) x 10H(2)O are determined to demonstrate the functionality of the rebuilt probehead.     

High-resolution heteronuclear correlation spectra between 31P and 27Al in microporous aluminophosphates

A solid-state nuclear magnetic resonance (NMR) experiment, which provides high-resolution two-dimensional heteronuclear correlation (HETCOR) spectra between 27Al and 31P, is described. The first part of the experiment uses triple-quantum or quintuple-quantum magic-angle spinning (MQMAS) NMR of spin-5/2 nuclei (27Al) to produce an isotropic echo that is unaffected by the second-order quadrupolar broadening. The magnetization is then transferred to the spin-1/2 (31P) nuclei via cross-polarization (CP), resulting in isotropic resolution in both spectral dimensions. To illustrate its usefulness, this method (referred to as MQHETCOR) is applied to two important microporous framework aluminophosphates, hydrated VPI-5 and AIPO4-40.     

Solvent Magnetization Artifacts in High-Field NMR Studies of Macromolecular Hydration

With the use of high magnetic fields and improved quality factor ratings of the probeheads in modern NMR spectrometers, radiation damping becomes more and more important. In addition, the demagnetizing field effect from protonated solvents gains significance with the increase of the magnetic field strength. During a typical NMR pulse sequence the magnetic fields caused by these effects become time-dependent, which makes the system nonlinear and may, for example, measurably influence the precession frequencies of all nuclei in the sample. Since radiation damping can affect signals that are several kilohertz away from the solvent resonance, the amplitude, phase, and frequency of the desired signals can be disturbed so as to give rise to spectral artifacts. In particular when difference methods are used to obtain the final spectrum, the data sets may be severely deteriorated by such artifacts. This paper investigates effects from the demagnetizing field and from radiation damping with a selection of pulse sequences in use for studies of macromolecular hydration, and strategies are described for the detection and elimination of the ensuing artifacts.     

用固体核磁方法研究MCM-22分子筛中的Al状态

用固体NMR技术研究了新型分子筛MCM-22在不同水合状态下的²⁷Al谱和¹H谱.并用新的¹H/²⁷Al双共振方法TRAPDOR对MCM-22分子筛的各种铝状态进行了研究,得到了样品脱水后B酸位(Bronsted)、L酸位(Lewis)以及非骨架Al(OH)的四极耦合常数.     

A combined 14N/27Al nuclear magnetic resonance and powder X-ray diffraction study of impurity phases in beta-sialon ceramics

Beta-sialons are ceramic phases occurring in the SiO(2)-Si(3)N(4)-AlN-Al(2)O(3) system. A series of samples with differing compositions has been investigated by magic-angle spinning nuclear magnetic resonance (NMR) spectroscopy and powder X-ray diffraction (XRD). Although the constituent nitrogen nuclei occupy positions of low symmetry in the beta-sialon structure, 14N NMR spectra could be recorded for the samples examined. The origin of the 14N signal could be traced to the presence of an aluminium nitride (AlN) impurity phase with the help of 27Al NMR and XRD results. Similarly, the existence of Al(2)O(3) grains could be readily detected for a number of samples. Thus, the combination of 14N and 27Al NMR is shown to be an especially effective tool in identifying and characterizing impurity phases in sialon ceramics, complementing the results obtained from standard XRD analysis.     

Unambiguously distinguishing Si[3Si,1Al] and Si[3Si,1OH] stuctural units in zeolite by 1H/29Si/27Al triple resonance solid state NMR spectroscopy

We present an experimentally feasible triple-resonance NMR method that establishes the correlation among three different nuclei, avoiding the difficulty to directly explore the weak coupling between two NMR nuclei, such as (29)Si and (27)Al. Using this method, we are able to give an unambiguous assignment to the various peaks in (29)Si CP NMR spectrum of MCM-22 zeolite and discriminate (29)Si signals from SiOHAl and SiOH groups. In addition, in combination with (1)H/(27)Al double-resonance technique, the (1)H/(27)Al/(29)Si triple-resonance experiment suggests the presence of two different kinds of Br?nsted acid sites in H-MCM-22 zeolite.     

<Superscript>27</Superscript>Al NMR Study of the Structure and Dynamics of Natrolite

The temperature dependences of nuclear magnetic resonance and magic angle spinning nuclear magnetic resonance spectra of ²⁷Al nuclei in natrolite (Na₂Al₂Si₃O₁₀· 2H₂O) have been studied. The influence of water molecules and sodium ions mobility on the shape of the ²⁷Al NMR spectrum and framework dynamics have been discussed The temperature dependences of the spin–lattice relaxation times T₁ of ²⁷Al nuclei in natrolite have also been studied. It has been shown that the spin–lattice relaxation of the ²⁷Al is governed by the electric quadrupole interaction with the crystal electric field gradients modulated by translational motion of H₂O molecules in the natrolite pores. The dipolar interactions with paramagnetic impurities become significant as a relaxation mechanism of the ²⁷Al nuclei only at low temperatures (<270 K).     

Functional MRI and NMR spectroscopy of an operating gas-liquid-solid catalytic reactor

A dynamic in situ study of alpha-methylstyrene catalytic hydrogenation on a single catalyst pellet or in a granular bed is performed using 1H MRI and spatially resolved 1H NMR spectroscopy. Owing to reaction exothermicity, a reciprocating motion of the liquid front within the pellet accompanied by pellet temperature oscillations has been observed. Spatially resolved information on the reactant to product conversion within the catalyst bed has been obtained for a steady-state regime. Two-dimensional 27Al NMR images of alumina catalyst supports and other alumina-containing materials have been detected using moderate magnetic field gradients (80 G/cm) and a two-pulse spin-echo sequence. Temperature dependence of signal intensity and 27Al T1 time of alumina are considered as possible temperature sensors for NMR thermometry applications.     

Al nuclear magnetic resonance study of synthetic and natural corundum (α-Al2O3) Some experimental aspects of quantitative Al nuclear magnetic resonance spectroscopy

The ²⁷Al nuclear magnetic resonance (NMR) response of a series of natural and synthetic corundum (α-Al₂O₃) samples is studied quantitatively by short-pulse excitation and frequency-stepped adiabatic half-passage (FSAHP). Using on- and off-resonance nutation NMR, it was established that the quadrupole coupling parameters of visible Al is identical in all samples. Remarkably, the relaxation behavior for the aluminum is very different in the various samples and has a marked effect on the quantitative response. In natural corundum samples the ²⁷Al spin-lattice relaxation is very efficient as these samples contain paramagnetic impurities. As a result, however, the full signal could not be recovered, which is attributed to relaxation broadening of spins in the vicinity of these impurities. In synthetic samples, containing no impurities, the full signal could be recovered, although the relaxation behaviour appeared to depend strongly on the preparation method. We observed differences in the spin-lattice relaxation by a factor 20; the longest T₁ was observed in a crushed single crystal. This implies that α-Al₂O₃ can only be used as a standard in quantitative analyses if it has been characterized thoroughly. Furthermore, the effective relaxation behaviour for different types of excitation is studied. Finally, a method to measure the spin-lattice relaxation of half-integer quadrupole nuclei is introduced, using a frequency-stepped adiabatic passage (FSAP) to invert the spin system.     

Perturbed Al photon echo ENDOR double resonance in Pr:YAlO3 and Eu:YAlO3

Aluminum pure quadrupole spectra measured by photon echo ENDOR double resonance (PENDOR) are reported for crystals of YAlO₃ doped with Pr³⁺ and for crystals doped with Eu³⁺. These spectra, which correspond to aluminum nuclei adjacent to a rare earth impurity, are compared to the results of a conventional NMR study of ²⁷ Al in YAlO₃.     

Electronic characterization of lithographically patterned microcoils for high sensitivity NMR detection

Nuclear magnetic resonance (NMR) offers a non-destructive, powerful, structure-specific analytical method for the identification of chemical and biological systems. The use of radio frequency (RF) microcoils has been shown to increase the sensitivity in mass-limited samples. Recent advances in micro-receiver technology have further demonstrated a substantial increase in mass sensitivity [D.L. Olson, T.L. Peck, A.G. Webb, R.L. Magin, J.V. Sweedler, High-resolution microcoil H-1-NMR for mass-limited, nanoliter-volume samples, Science 270 (5244) (1995) 1967–1970]. Lithographic methods for producing solenoid microcoils possess a level of flexibility and reproducibility that exceeds previous production methods, such as hand winding microcoils. This paper presents electrical characterizations of RF microcoils produced by a unique laser lithography system that can pattern three dimensional surfaces and compares calculated and experimental results to those for wire wound RF microcoils. We show that existing optimization conditions for RF coil design still hold true for RF microcoils produced by lithography. Current lithographic microcoils show somewhat inferior performance to wire wound RF microcoils due to limitations in the existing electroplating technique. In principle, however, when the pitch of the RF microcoil is less than 100 μm lithographic coils should show comparable performance to wire wound coils. In the cases of larger pitch, wire cross sections can be significantly larger and resistances lower than microfabricated conductors.     

Parallelizing acquisitions of solid-state NMR spectra with multi-channel probe and multi-receivers: Applications to nanoporous solids

A five-channel (¹H, ¹⁹F, ³¹P, ²⁷Al, ¹³C) 2.5 mm magic-angle-spinning (MAS) nuclear magnetic resonance (NMR) probe is used in combination with three separate receivers for the parallel acquisitions of one (1D) and two-dimensional (2D) NMR spectra in model fluorinated aluminophosphate and porous Al-based metal-organic framework (MOF). Possible combinations to record simultaneously spectra using this set-up are presented, including (i) parallel acquisitions of quantitative 1D NMR spectra of solids containing nuclei with contrasted T₁ relaxation rates and (ii) parallel acquisitions of 2D heteronuclear NMR spectra. In solids containing numerous different NMR-accessible nuclei, the number of NMR experiments that have to be acquired to get accurate structural information is high. The strategy we present here, i.e. the multiplication of both the number of irradiation channels in the probe and the number of parallel receivers, offers one possibility to optimize this measurement time.     

Direct Detection of Al–O–Al Structure in Aluminosilicate Specimens: A Use of Homo-Nuclear DQMAS NMR

A general strategy of Al–O–Al structure in various aluminosilicate was evaluated by combining triple-quantum magic angle spinning (3QMAS) and double-quantum homo-nuclear correlation under magic angle spinning (DQMAS) solid-state nuclear magnetic resonance (NMR) measurements with the aid of high magnetic field NMR (800 MHz for ¹H Larmor frequency). The results show that in many cases the direct detection of Al–O–Al sites in aluminosilicate crystals and glasses is possible; hence the extent of aluminum avoidance can be directly elucidated. Specifically, experimental evidence of Al–O–Al linkages in several aluminosilicate materials with Si/Al >1 was straightforwardly confirmed; and the existence of Al–O–Al is considered to have little correlation with the Si/Al ratio, but it may be strongly related to the cation and local structural arrangement. In addition, the presence of tri-clusters of (Si, Al)O₄-tetrahedra in aluminosilicate framework was proposed, which was thought to act as nuclei for formation and incorporation of cations to achieve charge neutrality.     

High-field 19.6T 27Al solid-state MAS NMR of in vitro aluminated brain tissue

The combination of (27)Al high-field solid-state NMR (19.6T) with rapid spinning speeds (17.8 kHz) is used to acquire (27)Al NMR spectra of total RNA human brain temporal lobe tissues exposed to 0.10 mM Al(3+) (as AlCl(3)) and of human retinal pigment epithelial cells (ARPE-19), grown in 0.10 mM AlCl(3). The spectra of these model systems show multiple Al(3+) binding sites, good signal/noise ratios and apparent chemical shift dispersions. A single broad peak (-3 to 11 ppm) is seen for the aluminated ARPE-19 cells, consistent with reported solution-state NMR chemical shifts of Al-transferrin. The aluminated brain tissue has a considerably different (27)Al MAS NMR spectrum. In addition to the transferrin-type resonance, additional peaks are seen. Tentative assignments include: -9 to -3 ppm, octahedral AlO(6) (phosphate and water); 9 ppm, condensed AlO(6) units (Al-O-Al bridges); 24 ppm, tetrahedral AlO(3)N and/or octahedral Al-carbonate; and 35 ppm, more N-substituted aluminum and /or tetrahedral AlO(4). Thus, brain tissue is susceptible to a broad range of coordination by aluminum. Furthermore, the moderate (27)Al C(Q) values (all less than 10 MHz) suggest future NMR studies may be performed at 9.4T and a spin rate of 20 kHz.     

27Al NMR spectroscopy of minerals and related materials

We present a review of the applications of²⁷Al NMR methods to investigations of the structures of minerals, primarily alumino-silicates, and related synthetic compounds. Such materials are ubiquitous in the earth and other terrestrial planets. Because of their diverse structures and compositions, they also provide examples of many situations in which²⁷Al NMR spectroscopy can provide useful information. Thus, they serve well as model compounds for synthetic crystalline and amorphous materials and usefully illustrate the applications of many techniques. The advent of high-field superconducting magnets (H ₀>9 T) has made application of²⁷Al NMR to solids much more effective than it was previously, and we focus primarily on these recent applications but also discuss older, single-crystal data.²⁷Al NMR methods can be used for many purposes in investigations of solids. Here we emphasize the following. 1) Determination of the Al coordination number and the polymerization of tetrahedrally coordinated Al. 2) Determination of tetrahedral Al/octahedral Al ratios. 3) Investigation of tetrahedral Al, Si order/disorder in, especially, framework-structure alumino-silicate phases. 4) Investigation of the static structural changes and dynamical behavior of crystals undergoing structural phase transitions. 5) Investigation of the local symmetry of Al-sites through the quadrupole coupling constant and asymmetry parameter.     

Operating nanoliter scale NMR microcoils in a 1 tesla field

Microcoil probes enclosing sample volumes of 1.2, 3.3, 7.0, and 81 nanoliters are constructed as nuclear magnetic resonance (NMR) detectors for operation in a 1 tesla permanent magnet. The probes for the three smallest volumes utilize a novel auxiliary tuning inductor for which the design criteria are given. The signal-to-noise ratio (SNR) and line width of water samples are measured. Based on the measured DC resistance of the microcoils, together with the calculated radio frequency (RF) resistance of the tuning inductor, the SNR is calculated and shown to agree with the measured values. The details of the calculations indicate that the auxiliary inductor does not degrade the NMR probe performance. The diameter of the wire used to construct the microcoils is shown to affect the signal line widths.     

Y型沸石脱铝机制和铝状态的NMR研究

对Y型沸石原粉及几种不同脱铝样品进行了几种不同NMR方法的测量,确定了不同处理过程的脱铝机制和骨架内外铝状态的变化,²⁹Si MAS NMR谱给出了骨架Si、Al分布的信息,反映了不同方法处理样品其脱铝机制的差异,据此可以控制Y沸石脱铝过程获得更高的硅铝比,²⁷Al MAS NMR谱、二维章动NMR及¹H-²⁷Al CP/MAS NMR测量表明:水热处理的Y沸石中存在4种不同的铝状态。综合²⁹Si和²⁷Al MAS NMR观测,可相当程度地推断Y型沸石分子筛脱铝改性所发生的内部过程。     

Irreducible spin precession theory applied to some topics in atomic and nuclear radio-frequency spectroscopy

Several problems from radio-frequency spectroscopy of atoms and nuclei are treated with irreducible spin precession theory. In the first part, effective field techniques are used to derive analytically single and multiple quantum double resonance lineshapes for atoms with a hyperfine structure in a high magnetic field. In the second part (as an extension to previous work), nuclear resonance signals are calculated for oriented nuclei subject to an electric hexadecapole interaction. Lineshapes of acoustically driven hexadecapole transitions are derived in closed form and compared to experiment. Further, multiple quantum NMR transitions within a hexadecapole shifted nuclear Zeeman structure are calculated, and some distinct features of hexadecapole effects on NMR lineshapes are pointed out. This last case is of current interest due to recent progress in NMR-line narrowing techniques. — In the Appendix, we give lineshape equations for single and double quantum NMR transitions on oriented (I=1)-nuclei subject to an electric quadrupole interaction; these equations are also being used in the atomic rf-spectroscopy calculations. The equations are exact to all orders of the interaction with the external fields.     

Three-dimensional through-bond homonuclear-heteronuclear correlation experiments for quadrupolar nuclei in solid-state NMR applied to (27)Al-O-(31)P-O-(27)Al networks

We present here the first 3D homonuclear/heteronuclear correlation experiment applied to quadrupolar nuclei and making use of the sole scalar J-coupling. This experiment, based on the 2D-Homonuclear-Heteronuclear Single Quantum Correlation (H-HSQC) experiment, uses a relayed transfer from the (27)Al central transition to neighbouring (31)P spins and to the central transition of a second (27)Al. It confirms the correlation map characterizing the two (27)Al and the (31)P NMR signatures of (27)Al-O-(31)P-O-(27)Al chemically bonded molecular motifs.     

Double rotation27Al NMR in molecular sieves

Although high-resolution NMR spectra can be obtained in solids, the use of²⁷Al NMR to investigate the structure of aluminosilicate and aluminophosphate molecular sieves has been severely limited because anisotropic second-order quadrupolar interactions, responsible for spectral broadening, cannot be eliminated by conventional magic angle spinning (MAS) or multiple pulse techniques. Here we give the principles of the double rotation (DOR) NMR technique which can remove not only the first-order broadenings but also the second-order broadenings in the NMR spectra of quadrupolar nuclei in solids. High-resolution²⁷Al NMR using DOR is capable of resolving discrete framework aluminum sites in aluminophosphate molecular sieves, permitting quantitative investigation of site-specific adsorbate-host interactions, and of discriminating different aluminum species in zeolites.