Electrocatalytic activity of poly(3-methylthiophene) electrodes

Poly 3-methylthiophene (P3MT) modified electrodes have shown an improvement for detecting catecholamines when compared to classical ones. Past work with this polymer electrode suggested the possible presence of “active sites,” which are believed to be the polymer’s center of electrocatalytic activity. The interaction of 1,5-anthroquinone-disolfonic acid (1,5-AQDS) at the P3MT electrode showed a nonreversible behavior resulting in the blocking of “the active sites,” suggesting the specific electcatalytical activity of this polymer is limited to catechol and similar compounds. In order to improve catecholamine detection, two methods of electropolymerization for P3MT were compared under similar conditions; (1) a constant potential for a specific length of time, and (2) potential cycling. It was found that cycling provided a more sensitive CV, i.e. increased number of active sites. Under a controlled pH study (pH range 2–9), the polymer electrode maintained its superior performance, manifested as lower ΔE and higher i, toward catechol over the traditional electrodes. Two different supporting electrolytes were used, sulfate and phosphate, and it was found that in neutral or basic solutions containing phosphate, the oxidation and reduction potentials of catechol shifted to lower values. Solutions containing sulfate exhibited no shift in the oxidation potential at any pH value.     

Electrosynthesis and characterization of poly(3-methylthiophene) on different substrates

 We report on the study of the electropolymerization of 3-methylthiophene onto Pt, p-Si and indium-tin oxide deposited on polyester using quartz crystal microgravimetry, electrochemical and spectroelectrochemical measurements. We observe that potential variation during the galvanostatic electrodeposition is correlated with the nucleation process. The mass variation of poly(3-methylthiophene) is linear with the amount of the electrochemical charge whereas the absorbance variation curve shows two distinct slopes. The latter result has been explained in terms of conjugation length variation during polymer growth. Scanning electron microscopy analysis allowed the detection of morphological changes from a dense and compact structure to an open morphology when the poly(3-methylthiophene) film thickness increases. The roughness of the films did not change considerably with the substrate, as observed by atomic force microscopy. Absorption and photocurrent spectra at different film thicknesses show a shift of the peaks to lower wavelengths when the thickness increased, thus confirming the decrease of mean conjugation length in thicker films. Received: 1 September 1998 / Accepted: 11 November 1998     

Analytical applications of organized assemblies for on-line spectrometric determinations: present and future

An amphiphile (surfactant) spread on water can lead to the formation of different aggregates: vesicles, miscelles, emulsions or microemulsions; depending on its concentration; its molecular structure and/or the experimental conditions. Such aggregates, (a) may concentrate products, reactants or analytes and so improve the analytical sensitivity and (b) may solubilize such substances and so favorably change the analytical selectivity. Bilayer membrane vesicles for instance, apart from their wide applications in cosmetic and pharmaceutical industries, have a great analytical potential due to their ability to (i) reversibly sequester metal ions avoiding matrix interference and (ii) improve cold vapor (Hg and Cd) and hydride (As, Se, Pb) chemical generation. Micellar solutions have also found wide applications in different areas of analytical chemistry, showing their capacity to concentrate and separate a significant variety of analytes. Among the numerous micelle-based separation techniques, cloud point extraction offers an excellent enrichment factor for metal ions, allowing their quantification at microgram/litre levels. Also agitating a mixture of water, oil and one or more surfactants under controlled experimental conditions, a cloudy mixture (emulsion) or a transparent solution (microemulsion) can be formed. Adequate formulation is necessary in order to obtain a stable organized media. To fulfill this requirement, a major effort is necessary in order to shorten the gap between the current knowledge on this topic and the promising field of applications that await development. Recent publications show that self-assembly structures from highly viscous samples can be accomplished on-line with the advantages of drastically reducing the time of analysis and assuring the absolute control over the stability of the aggregate. Flow systems allow effective mixing of samples with added surfactant and provide continuous pumping of the resulting mixture to sensitive detectors for the on-line determination of different analytes in complex samples.     

Voltammetric detection of sulfonamides at a poly(3-methylthiophene) electrode

Detection of sulfonamide compounds in a mixture of standards at a poly(3-methylthiophene) coated on glassy carbon (GC) electrode is reported. The polymer, poly(3-methylthiophene), was electrochemically synthesized at a GC rotating disk-working electrode versus Ag/AgCl using cyclic voltammetry (+0.5 to +2.0 V). Square wave voltammetry (SQWV) with cathodic reduction (0 to -4.0 V) was used for the detection of seven sulfonamide compounds in a mixture. The working concentration ranges (curvilinear) established for different compounds in Britton-Robinson (BR) buffer (pH 6.26), were: 5.0x10(-6)-3.2x10(-3) M sulfamerazine, 5.0x10(-6)-3.2x10(-3) M sulfadiazine, 7.5x10(-7)-3.2x10(-4) M sulfasalazine, 9.0x10(-7)-5.0x10(-4) M sulfamethazine, 6.5x10(-8)-3.5.0x10(-5) M sulfamethoxazole, 9.7x10(-8)-5.0x10(-5) M sulfathiazole, and 9.0x10(-8)-3.2x10(-5) M 5-sulfaminouracil. Detection limits were calculated as: 3.9x10(-6) M for sulfamerazine; 4.0x10(-6) M sulfadiazine; 2.5x10(-7) M sulfasalazine; 3.7x10(-7) M sulfamethazine; 4.0x10(-8) M sulfamethoxazole; 6.4x10(-8) M sulfathiazole and 6.0x10(-9) M 5-sulfaminouracil. The data suggests a potential application of the poly(3-methylthiophene) (P3MT) electrode for determination of sulfonamides in veterinary and other applications.     

Enhanced photoresponse of poly(3-methylthiophene) supported on TiO2

We have investigated the photoelectrochemical behavior of poly(3-methylthiophene) supported on nanostructured n-TiO₂ in a solid-state photoelectrochemical device. As electrolyte we employed the elastomer poly(epichlorohydrin-co-ethylene oxide) filled with NaI/I₂. Under polychromatic light irradiation (60 mW cm⁻²) the device exhibits an open circuit voltage, a short-circuit current and fill factor of 10 μA cm⁻², 0.048 V and 0.29, respectively. The overall efficiency of the cell is 2.3×10⁻²%.     

Simultaneous determination of levodopa and benserazide using poly(3-methylthiophene) and a multi-walled carbon nanotube sensor

Journal of Solid State Electrochemistry - Rapid, reliable, reproducible, and repeatable modified sensor designs have been developed to distinguish the binary mixture of levodopa and benserazide in...     

Potentiometric response of poly(3-octylthiophene), poly(3-methylthiophene) and polythiophene in aqueous solutions

The potentiometric response of some polythiophenes in aqueous solutions has been investigated. Polythiophene (PT), poly(2,2'-bithiophene) (PBT), poly(3-methylthiophene) (PMT), poly(3-octylthiophene) (POT) and poly(4,4'-dioctyl2,2'-bithiophene) (POTd) were electrochemically deposited on platinum in 0.1M LiBF(4)-propylene carbonate solution containing the corresponding monomer or dimer. Polymer electrodes were also prepared by solution casting of chemically synthesized poly(3-octylthiophene) (POTc) dissolved in chloroform. After film deposition (electrochemical or chemical) the polymer coated electrodes were used as indicator electrodes in potentiometric measurements. The open-circuit potential of the polymer electrodes was measured in aqueous solutions containing inorganic salts (10(-1)-10(-4)M). Interestingly, all the polythiophenes studied were found to give a cationic response to monovalent cations such as H(+), Li(+), Na(+), K(+) and NH(+)(4) (Cl(-) salts). The slope, calculated from the linear part of the response curve, was found to depend on the polythiophene used but always remained lower than that predicted for a Nernstian response. The polythiophenes also showed some sensitivity to divalent cations such as Mg(2+) and Ca(2+) (Cl(-)-salts). POT was used as the polymer to study the influence of the polymerization conditions on the potentiometric response. By investigating different polymers from the polythiophene family it was possible to evaluate how the starting material (monomer or dimer) and the presence of alkyl side-chains influence the potentiometric response of the polymer membranes.     

Sulfonated polyaniline/poly(3-methylthiophene)-based photovoltaic devices.

A sulfonated polyaniline (SPAN) film as an intermediate layer between the electrode, tin oxide (TO) and the active layer improves the efficiency of photovoltaic devices based on poly(3-methylthiophene), PMT. In TO/SPAN/PMT/Al devices, the incident-photon-to-collected-electron efficiency reaches 12.1% and power conversion efficiency 0.8% under monochromatic irradiation (λ = 580 nm; 0.8 W/m²). Under AM 1.5 conditions 1000 W/m², a power conversion efficiency of 0.04% is reached.     

Solvation/desolvation during the redox transformation of poly(3-methylthiophene)

Solvation/desolvation effects were studied during the redox transformation of poly(3-methylthiophene) by electrochemical quartz crystal microbalance technique. The effect was demonstrated by studying the phenomenon in different solvents, and comparing the results after a solution change. From the data obtained with the same film transferred between nitrobenzene and acetonitrile in both directions, the solvation effect was directly evidenced, and the virtual molar mass of the moving species in and from the same film was determined to illustrate semi-quantitatively the effect of the solvation.This paper is dedicated to Professor G. Horányi on the occasion of his 70th birthday and in recognition of his outstanding contribution of electrochemistryCsaba Visy, Emese Kriván are ISE members     

Electrochemical determination of diphenols and their mixtures at the multiwall carbon nanotubes/poly (3-methylthiophene) modified glassy carbon electrode

This paper describes a sensitive electrogenerated chemiluminescence (ECL) method for cystine determination with improved analytical characteristics based on the combination of electrochemical parallel catalytic reaction and chemiluminescence (CL) signal sensing. Cystine can be electrochemically reduced and gives a parallel catalytic wave effect in the presence of potassium persulfate. The reaction circulated on the electrode and the amount of the reduced product of the potassium persulfate was accumulated at the electrode surface. Then the reduced product of potassium persulfate reacts with fluorescein to emit a sensitive CL signal. Investigation of the characteristics of the electrochemical and chemiluminescence reactions revealed that the speed of the electrochemical reaction was much faster than that of the subsequent CL reaction, which proved the possibility of the combination of electrochemical parallel catalytic reaction with CL signal sensing. The ECL intensity is linearly related to the cystine concentration in the range from 60 nM to 8.0 μM.     

Electrical characterization of poly(3-methylthiophene) electrosynthesized onto a tin-oxide substrate

We have investigated poly(3-methylthiophene) (PMeT) thin films electrochemically synthesized directly onto a tin-oxide (TO) electrode. We find that the PMeT film thickness depends linearly on the charge density used during the electropolymerization. We have demonstrated that the current transport in PMeT films (solid phase) is space-charge limited or controlled by thermionic emission, depending on the electrode material. Using TO/PMeT/Ni devices we estimate the positive charge carrier mobility in PMeT to be around 4 × 10⁻⁴ cm² V⁻¹ s⁻¹, and the potential barrier height for positive charge carrier injection at the Al/PMeT interface to be 0.17 eV. Received: 6 December 1999 / Accepted: 24 February 2000     

Study of free volume and crystallinity in polybithiophene and poly(3-methylthiophene)

Compressed pellets of partly crystalline, chemically synthesized, doped (Cl^? and FeCl) polybithiophene (PBTd), poly(3-methylthiophene) (P3MTd), and their neutral (dedoped) forms (PBTn and P3MTn) were studied by wide-angle x-ray diffraction and positron annihilation lifetime spectroscopy. As synthesized, PBTd and P3MTd polymers have a helical syn conformation they crystallize in the hexagonal system. On dedoping, PBT macromolecules change their helical syn conformation in a rodlike anti conformation and crystallize in the orthorhombic or monoclinic system, whereas P3MT macromolecules retain their helical syn conformation. Chemical doping–dedoping cycles lead to amorphous PBT and P3MT in either doped or dedoped states. The P3MT helical macromolecule behaves like a spiral spring; by doping, it becomes axially compressed. The unit-cell volume of P3MTd is smaller than that of P3MTn. The positron lifetime spectra for all polymers were resolved, without constraint, into three components. The τ₁ lifetime is attributed to free-positron annihilation events, the τ₂ lifetime to positrons annihilating trapped in voids, and the τ₃ lifetime to positrons annihilating as o-Ps trapped in cavities located inside the polymer grains for P3MTn and at the surface of the grains for PBTd, PBTn, and P3MTd. Most positrons annihilate when trapped in voids, both in doped and dedoped PBT and P3MT. The doping apparently increases the concentration of the voids and their mean diameter in P3MT, and probably also in PBT. Cavities anchored in the bulk are produced by dedoping. © 1993 John Wiley & Sons, Inc.     

聚(3-甲基噻吩)的电化学稳定性及电催化行为

用连续循环伏安法研究了电化学法制备的聚(3-甲基噻吩)(PMT)薄膜修饰玻璃碳电极在不同支持电解质溶液中的电化学稳定性。在易嵌入PMT的阴离子存在下, PMT电活性随扫描次数按表现二级反应降低; 在难嵌入PMT的离子存在下, PMT具有良好稳定性; 在含有氯、溴离子的水溶液中, PMT可将卤离子电催化氧化, 并引起PMT电活性迅速下降。光电子能谱分析表明氯已键合到PMT结构上。     

Tuning of the charge and energy transfer in ternary CdSe/poly(3-methylthiophene)/poly(3-hexylthiophene) nanocomposite system

Composite CdSe:poly(3-methylthiophene) (P3MT) nanoparticles have been synthesized via polymerization of 3-methylthiophene (3MT) in the presence of CdSe particles of nanorod or dot-like morphology and dispersed in the poly(3-hexylthiophene) (P3HT) matrix. The effect of the P3MT layer to mediate charge and energy transfer between CdSe and P3HT in the ternary nanocomposite system has been studied using electronic absorption, photoluminescence spectroscopy, and current–voltage measurements. The energy level diagram of the composite system has been deduced based on optical and electrochemical data of the separate components of the system. The contribution of the low- and high-molecular fractions of P3MT to control the charge transfer in order to optimize the intermediary role of P3MT is analyzed. Particularly, it was shown that excitation of the low-molecular P3MT leads to energy transfer to both CdSe and P3HT components, and it also serves as a barrier against recombination of electrons and holes separated at CdSe and P3HT, respectively. Thus, the role of the P3MT interlayer in assisting the charge separation and increasing an open-circuit voltage in the photovoltaic cell based on the ternary system is demonstrated.     

Chemical preparation and characterization of fibrous poly(3-methylthiophene) decorated by TiO2 nanoparticles

In this article, we report on the chemical oxidative polymerization of 3-methylthiophene (3MTh) in a concentrated TiO₂/CHCl₃ homogeneous suspension with an oxidant/monomer mole ratio of 3 at room temperature. According to the scanning electron microscopy images, in this condition, poly(3-methylthiophene) (P3MTh) was prepared with fibrous morphology decorated by nano-dimensional TiO₂ particles. P3MTh/TiO₂ was also characterized by Fourier transform infrared spectroscopy and X-ray diffraction techniques. It was found that no aggregation of nanoparticles occurred during the polymerization process. In addition, the thermal stability of P3MTh/TiO₂ nanocomposite was investigated by thermogravimetric analysis and compared with that of an analogously prepared neat P3MTh. The thermal degradation of P3MTh in the temperature range of 300–550°C decreases significantly due to the presence of the TiO₂ nanoparticles in the polymer composite.     

Surface-initiated synthesis of poly(3-methylthiophene) from indium tin oxide and its electrochemical properties

Poly(3-methylthiophene) (P3MT) was synthesized directly from indium tin oxide (ITO) electrodes modified with a phosphonic acid initiator, using Kumada catalyst transfer polymerization (KCTP). This work represents the first time that polymer thickness has been controlled in a surface initiated KCTP reaction, highlighting the utility of KCTP in achieving controlled polymerizations. Polymer film thicknesses were regulated by the variation of the solution monomer concentration and ranged from 30 to 265 nm. Electrochemical oxidative doping of these films was used to manipulate their near surface composition and effective work function. Doped states of the P3MT film are maintained even after the sample is removed from solution and potential control confirming the robustness of the films. Such materials with controllable thicknesses and electronic properties have the potential to be useful as interlayer materials for organic electronic applications.     

Capillary zone electrophoresis of proteins with poly(2-hydroxyethyl methacrylate)-coated capillaries: fundamentals and applications

Fused silica capillaries have been modified by atom-transfer radical polymerization (ATRP) to generate covalently bonded polymer films of 2-hydroxyethyl methacrylate. Because the kinetics of ATRP have mainly been investigated in bulk solutions, a GC experiment was set up to examine monomer conversion inside narrow-bore capillaries. It was shown that after 1 to 4 h the reaction was nearly complete. The coating process was further optimized by monitoring EOF, because low EOF indicates high surface coverage. To deal with the very low EOF values, a new approach was used to dramatically reduce the measurement time by overlaying hydrodynamic flow on the electroosmotic flow. The corresponding equations are derived separately in detail. Capillaries were then coated under optimum conditions with linear or cross-linked polymer films. The EOF was reduced over a wide range of pH values. A long-term reproducibility test with both types of functionalization showed that the efficiency of the linear polymer coating decreased significantly over time. With cross-linked films, however, the efficiency even increased. Relative standard deviations for protein migration times were also much lower in cross-linked coated capillaries. Highly efficient separations could be performed for basic and acidic proteins in acidic media, and for the latter even in basic media. Received: 14 September 2000 / Revised: 26 November 2000 / Accepted: 30 November 2000     

Capillary zone electrophoresis of proteins with poly(2-hydroxyethyl methacrylate)-coated capillaries: fundamental and applications

Fused silica capillaries have been modified by atom-transfer radical polymerization (ATRP) to generate covalently bonded polymer films of 2-hydroxyethyl methacrylate. Because the kinetics of ATRP have mainly been investigated in bulk solutions, a GC experiment was set up to examine monomer conversion inside narrow-bore capillaries. It was shown that after 1 to 4 h the reaction was nearly complete. The coating process was further optimized by monitoring EOF, because low EOF indicates high surface coverage. To deal with the very low EOF values, a new approach was used to dramatically reduce the measurement time by overlaying hydrodynamic flow on the electroosmotic flow. The corresponding equations are derived separately in detail. Capillaries were then coated under optimum conditions with linear or cross-linked polymer films. The EOF was reduced over a wide range of pH values. A long-term reproducibility test with both types of functionalization showed that the efficiency of the linear polymer coating decreased significantly over time. With cross-linked films, however, the efficiency even increased. Relative standard deviations for protein migration times were also much lower in cross-linked coated capillaries. Highly efficient separations could be performed for basic and acidic proteins in acidic media, and for the latter even in basic media.     

The effect of electrolyte-controlled growth morphology on the charge transport properties of poly(3-methylthiophene)

Poly(3-methylthiophene) films were potentiostatically and galvanostatically synthesized on platinum electrodes in acetonitrile using lithium perchlorate, lithium tetrafluoroborate, tetra-n-butylammonium perchlorate, and tetra-n-butylammonium tetrafluoroborate as supporting electrolytes. Cyclic voltammetric analyses of the polymer films indicate the synthesis is polymerization process dependent. Constant potential syntheses, which resulted in a higher current density and were carried out at higher potentials, yielded polymer films with a higher charge capacity. Chronocoulometric results show that the charge transport rates of the films were electrolyte dependent and that tetra-n-butylammonium tetrafluoroborate yielded poly(3-methyl-thiophene) with the highest charge transport rate. The charge transport rate was found to be electric field dependent for all cases, suggesting that the films resemble a porous electrode. Scanning electron microscope analyses of the films, prepared under various conditions, indicate that the synthesis method used, and the nature of the electrolyte, strongly influence morphology and charge transport.     

Electrosynthesis of poly(3-methylthiophene) films: salt effect on the electrochemical and impedance properties

We studied the electrosynthesis of poly(3-methylthiophene) films in different electrolytes, i.e. 0.1?M quaternary ammonium salt solutions in acetonitrile. The analysis of the different results enabled us to explain the role of the cations and the anions of the electrolyte (doping agents) in the electrochemical synthesis and film properties. The films obtained with tetramethylammonium hexafluorophosphate (TMAPF₆) are more electroactive than those prepared using tetramethylammonium tetrafluoroborate (TMABF₄). This unexpected difference of behavior is due to the difference of hygroscopic properties of the two salts. We then characterized the films by electrochemical impedance spectroscopy. This technique, used to investigate the electrochemical properties, allowed us to virtually design identical electrical-equivalent circuits for the two types of film (prepared either with TMAPF₆ or with TMABF₄). We noted dissimilarities in the values of the components of those equivalent circuits. The different components were separately studied and their differences were explained by the salt effects.