Matching of quasioptical open resonators with waveguide feeders

We consider a semisymmetric open resonator (OR) included in a waveguide feeder, in which the first higher-order mode is excited. We show that a high efficiency of excitation of the mode can be achieved by appropriate choice of coupler dimensions due to the matching of structures of the exciting and operating fields. We analyze the behavior of the resonance reflection and transmission coefficients as well as the loaded Q-factor of an OR as functions of the parameters of one-dimensional E-polarized diffraction gratings located in a coupler aperture with dimensions of a few of wavelengths. Calculations are made with allowance for the resonance and excitation losses. The numerical results differ from the experimental data by no more than 13%, which allows one to construct open resonance systems with the required properties by changing the parameters of diffraction gratings in the coupler aperture. Institute of Radiophysics and Electronics, National Academy of Sciences of Ukraine, Kharkov, Ukraine Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Radiofizika, Vol. 43, No. 4, pp. 325–334, September, 2000.     

Side-pumped short rectangular Nd-doped phosphate glass fiber lasers

Watt-level short fiber lasers side-pumped through fiber-to-waveguide couplers are demonstrated. The fiber lasers are fabricated from Nd-doped phosphate glass with large numerical aperture of 0.2 and rectangular cross section of 1.5 × 0.5 (mm). Single transverse mode output is achieved by the gain-guiding effect. Average power of 1 W is generated from a 4.0-cm-long fiber laser with a slope efficiency of 10%.     

四杆与四翼型RFQ内的二极场研究

RFQ (射频四极透镜) 是直线加速器中最重要的前级聚焦加速结构，其工作模式下束流孔中的电场四极对称性是保证束流品质及加速效率的关键。为了解决其各自存在的工作模式下四极场的不对称问题，分别对四杆型RFQ 和四翼型RFQ 的结构和模式谐振特性做了研究。针对四翼型RFQ，模拟显示双端口对称耦合的方式从抵消二极模式和提高结构对称性两方面来达到削弱工作模式下的场分布中二极量的目的，对一个1 m段四翼RFQ 模型腔的测量证实了双端口对称耦合抵消腔内二极模式的有效性；针对四杆型RFQ 的二极场，以SSC-Linac 项目的RFQ 为原型，利用三维模拟计算软件CST-MWS 进行模拟，通过改进支撑板的结构并调整参数，完全地消除了工作模式下的极间二极场，且理论上此种改进方法对支撑板结构的四杆型RFQ 均有效。Radio Frequency Quadruple(RFQ) is the most important front-end acceleration structure in linear accelerators.It can focus and accelerate beam in longitudinal and transversal direction, simultaneously. Symmetric of electric field in acceleration aperture is very important for the beam dynamics. To an idea RFQ, there is only quadruple electric field in the acceleration aperture. The dipole field in aperture is harmful and need be as small as possible. The methods to reduce it are studied in a four-rod RFQ and a four-vane RFQ in the article ndependently. To a four-vane RFQ, the symmetrical double-port couplers are employed to counteract the neighboring dipole modes. The availability is confirmed by the simulation with the 3-D Finite Element tool, CST-MWS. And it is also observed by measuring a model-cavity with a symmetrical double-port couplers. To a four-rod RFQ, a new structure of stems is proposed to reduce the dipole mode.Taking the RFQ for the SSC-LINAC project as example, the dipole mode contributions to the electric filed is completely eliminated by selecting stem’s parameters carefully. It is confirmed by the simulation of CST-MWS. heoretically, this method is independent with the frequency of an RFQ and serves for all RFQs with 4-rod or 4-wane structure.     

Implementation of a diode-pumped Nd:YAG laser with quick-change output couplers for high-beam quality 1064 or 532 nm wavelength generation

A novel diode-pumped Nd:YAG laser system that employs a fixed active laser medium and a pair of quick-change output couplers on a precision linear stage for 1064 or 532 nm wavelength generation is presented. Fixed elements include a rear mirror, an acousto-optical Q-switch, and a diode-pumped solid-state laser (DPSSL). Movable elements for 1064 nm generation include an intra-cavity aperture as a mode selection element (MSE) and an output coupler. Movable elements for 532 nm generation include an intra-cavity frequency conversion with KTP, an intra-cavity aperture as a mode selection element (MSE), and an output coupler. Under stable operating conditions, the 1064 nm configuration produced a beam propagation ratio of 1.18 whereas the 532 nm configuration produced a beam propagation ratio of 1.1, both of which used an intra-cavity MSE with an aperture of 1.2 mm and a length of 5 mm.     

300 W侧面分布式抽运掺Yb全光纤放大器

采用角度磨抛的方式, 在纤芯/包层为20/400 μm双包层掺Yb光纤上制作了侧面抽运耦合器. 该耦合器对975 nm的半导体二极管抽运光的耦合效率最高可达97%, 对1080 nm信号光的泄漏比小于2%. 分析了侧面抽运耦合器的性能以及多个侧面抽运耦合器的级联分布对抽运耦合效率的影响; 同时, 在前向抽运和双向抽运方式下, 分析了级联耦合器的分布及信号光泄漏比对激光器整体效率的影响, 并进行了数值模拟. 采用自行研制的侧面抽运耦合器, 搭建了侧面耦合分布式抽运、掺Yb双包层全光纤主振荡功率放大器, 获得了波长为1080 nm、功率为303 W 的基模激光输出. 进一步增加抽运点个数, 提高抽运功率, 可获得更高的输出功率.     

AN OPEN RESONATOR FOR PHYSICAL STUDIES

The excitation efficency of the TEM_01q oscillation of an two-mirror hemispherical open resonator (OR) is studied. The resonator is excited by the TE₀₁ wave of a circular waveguide joined in the middle of the OR plane mirror. Given the waveguide optimum size, the TEM_01q mode excitation efficiency reaches 78%. Analysis of the resonant system spectrum in the 4-mm wave region shows that this waveguide-OR system offers a single mode resonance curve across almost a 10-GHz tuning range. The TEM₀₁₁₀ mode field distribution with and without the circular waveguide in the middle of the OR plane mirror is available due to the small scatterer method. It is shown that the considered open system is suitable for measuring electromagnetic characteristics of high-loss substances and metamaterials in the short-wave end of the millimeter (mm) region as well as in the submillimeter (submm) wave region.     

口径天线与近区厚介质体复杂系统的电磁建模

针对口径天线及其近区任意厚均匀介质体的复杂系统,应用表面积分方程（SIE）方法结合模式匹配方法（MM）建立了模式激励的新型一体化电磁模型。在馈电端口采取模式匹配方法模拟了波导中的激励情况,将金属壁处理为理想导电体,并在金属壁上利用边界条件建立电场积分方程（EFIE）;利用零场等效原理在介质体内外表面分别建立电场积分方程和磁场积分方程（MFIE）,并组合内外表面建立的电场积分方程和磁场积分方程为PMCHW方程;最后使用矩量法对所建立的EFIE-PMCHW-MM组合方程进行求解。文中结合喇叭天线设计了两个典型算例,所提混合方法EFIE-PMCHW-MM给出的数值结果与商用软件FEKO高度一致,且在求解口径天线与近区厚介质体耦合问题时由于未知量显著减少,大幅度提高了仿真效率,降低了计算机资源消耗。     

Design for broadband high-efficiency grating couplers

In this Letter, we propose general optimization methods to design broadband high-efficiency grating couplers for planar waveguides. We attribute the coupling bandwidth to the mismatch of effective indices between the diffracted beam and the actual grating structure around the operation wavelength for fiber to waveguide excitation. The coupling bandwidth formula is deduced. A simple parameter-separate optimization procedure is proposed for general layered grating couplers for high coupling efficiency. Using our principle, we optimized a grating coupler for a horizontal slot waveguide operating at wavelength 1.55 μm for TM polarization. The grating coupler has 1 dB bandwidth of 60 nm and coupling efficiency of 65% with incident light from single-mode optical fiber (SMF) at 8°.     

Aperture apodization to reduce the off-axis intensity of the pulsed-mode directivity function of linear arrays

There is considerable interest in aperture apodization for enhancing image quality. With continuous wave excitation, the influence of apodization can quite easily be predicted: the directivity function in the far-field corresponds to the Fourier transform of the aperture function. We, however, analyse a practical situation — short acoustic pulse emission focused in the near-field. Nine types of aperture function (for example, Tukey, Parzen, Hamming) are compared.It appears that with the pulsed mode a considerable reduction in off-axis intensity can be obtained by judicious choice of the aperture function. Side-lobes can be completely eliminated.As a tool, an approximate relationship is established between the Fourier transform of the aperture function and the main-lobe width of the directivity function. Further, an optimum balance is sought between the main-lobe width and the width at the ?25 dB level of the directivity function.     

基于公共环形腔耦合的光纤激光器相干合成技术

为提高光纤激光器无源自调整相干合成阵列的效率、稳定性和可扩展性,提出了基于公共光纤环形腔耦合与单模光纤滤波的光纤激光器相干合成方案。将多个2×2的光纤耦合器分别插入各单元激光器的谐振腔,利用耦合器余下的端口,两两相连构成公共环形耦合腔。采用单模光纤滤波技术,提高了各输出激光束之间相位锁定的稳定性。利用该方案在实验上实现了三路光纤激光器的被动锁相输出,实验测得的远场干涉光斑、输出功率及光谱均表明该方案适于构建性能较好的光纤激光器相干合成阵列。     

高功率单层径向线螺旋阵列天线的设计与模拟

 在研究磁探针耦合特性的基础上，设计了中心频率为4.0 GHz的3圈36单元高功率单层径向线螺旋阵列天线，各圈距中心位置分别为45，90，135 mm，单元个数分别为6，12，18。该天线采用磁探针代替电探针给短螺旋单元天线馈电，通过同轴-径向线模式转换器实现径向线TEM外行波激励，采用调整磁探针的探入深度和绕轴旋转短螺旋单元天线的方法改变单元的激励幅度与激励相位。数值模拟结果表明：该口径为324 mm的天线在中心频率上可获得21.58 dB的增益，口径效率可达78.2％，轴向轴比值为1.73；在3.8～4.2 GHz的频率范围内增益大于20.85 dB，口径效率大于73.2％，轴向轴比值小于2.0，反射系数小于0.27，辐射效率大于93%。     

Optical losses in dielectric apertured terahertz VCSEL

The resonant wavelength and mode radius of the fundamental modes supported by an oxide apertured terahertz vertical surface emitting laser are determined from Gaussian resonant theory and scalar variational method. The reflectivity of the Bragg mirror is calculated for the lowest modes and it decreases as the aperture size decreases. The aperture radius, thickness, and axial position in the cavity are shown to be an important factor for high efficiency vertical cavity surface emitting lasers and single mode operation. When the aperture size is much larger than the emitting wavelength, the optical loss is negligible. However, the optical loss strongly depends on the aperture size and thickness when aperture size is similar to or smaller than emitting wavelength.     

10 nm Spatial Resolution Fluorescence Imaging of Single Molecules by Near-Field Scanning Optical Microscopy Using a Tiny Aperture Probe

We demonstrate high-resolution fluorescence imaging of single molecules using near-field scanning optical microscopy (NSOM) with a tiny aperture probe for two different wavelengths in visible range in the illumination mode of operation. The spatial resolutions obtained at both excitation wavelengths were almost the same and the highest resolution realized was about 10 nm. To discuss the achievable resolution in aperture NSOM, we also employed a computer simulation by the finite-difference time-domain method for various aperture sizes and wavelengths. The resolution of 10 nm is predicted to be contributed by the single peak of localized near-field light around the rim of the aperture.     

Characteristics of Fused Optical Fiber Grating Couplers with Tapered Shapes

Fused optical fiber grating couplers (FGCs), in which Bragg gratings are written in the coupling regions of fused optical fiber couplers with tapered shapes along them are theoretically and experimentally investigated. By coupled mode analysis considering these tapered shapes, the drop efficiencies of the FGCs, which are inherently zero for the normal fiber couplers without grating, are calculated. The grating offset, which is the difference between the centers of grating and the coupler taper, is found to be effective to increase the drop efficiency of the FGC. It is determined that the tapered shapes influence the wavelength dependence of the drop efficiency and tolerate the grating offset precision. Apodizations for the grating of FGC are found to be effective in suppressing side lobes of the drop efficiency. Measurement of the wavelength characteristics of drop efficiency and the temperature characteristics of drop wavelength of the fabricated fused FGC confirm that the lightwave with specific wavelength can be dropped by the FGC and that the temperature dependence of the drop wavelength is similar to that of Bragg wavelength changes of usual fiber Bragg gratings.     

The degenerate multimode confocal resonator

The simultaneous excitation of the fundamental and higher order radial modes in a degenerate confocal resonator leads to destructive interference between modes on the optic axis and hence reduces the power coupled by an axial iris. This mode competition may be reduced drastically by proper control of the aperture flux distribution and is of particular significance when the resonator is used for the power combining of solid-state sources.     

Characterization of the approach to steady state and the steady-state properties of multimode optical fibers using LED excitation

A simple technique has been developed to characterize the approach to steady state and the steady-state properties of multimode fibers using LED excitation. Results are given for 6 mil Selfoc fibers whose far-field pattern for the steady state is in excellent agreement with a calculation by Marcuse. To first order, the steady-state mode distribution fits a simple model of uniform modal excitation of a fiber with a reduced numerical aperture.     

A novel approach to the aperture windowing in medical imaging

A new technique is proposed to improve the lateral resolution in the conventional B-mode imaging systems, which enables a simple array aperture windowing in the transmitting mode. Amplitude shaping is performed without modifying the transmitting voltage of the array elements, but only varying the excitation pulse length from one element to another. This method presents some attractive practical advantages, and the reduction of the sidelobe energy is comparable to that attainable with a conventional aperture windowing. Parametric plots are given, which transform an amplitude apodization into a 'time apodization' for any type of transducer array.     

Aperture efficiency and mode constituent analysis for OAM vortex beam generated by digital metasurface

A systematic study of the aperture efficiency and mode constituent for orbital angular momentum(OAM) vortex beam generated by digital metasurface is presented. The aperture efficiency and OAM spectrum are computed for different bit numbers. It is found that the aperture efficiency declines for digital metasurface due to the phase quantization error,especially for 1-bit device. Fortunately, the OAM spectrum is barely affected by phase quantization and the designated main mode keeps dominant for different bit numbers, indicating that high purity OAM vortex beam can be generated by digital metasurface. Besides, the influence of topological charge l is also investigated. For a fixed metasurface, the radiation performance deteriorates sharply with the growing of l and the parasitic OAM mode becomes dominant at certain angle.At last, a prototype of 1-bit metasurface was simulated, fabricated and measured in anechoic chamber. The simulation and experiment results verify the correctness of the numerical analysis.     

超声Lamb波二次谐波发生效率分析与模式选择

在导波模式展开分析方法的基础上,提出激发效率参量来定量表征超声Lamb波积累二次谐波的发生效率。以P92钢板为例,理论计算得到了与频散曲线对应的理论激发效率参量分布图谱,从图谱中选择理论激发效率参量大小不同的两种基频Lamb波模式:纵波型S1模式和交点型A2/S2模式,分别测量这两种基频Lamb波模式在钢板中传播时产生的二次谐波信号。理论计算和实验测量结果表明,这两种基频Lamb波模式的理论和实验激发效率参量的比值基本一致,且激发效率参量较大的纵波型S1模式能激发出效率更高的二次谐波信号。研究结果表明激发效率参量可以有效的用于Lamb波二次谐波发生效率的表征及模式选择。     

二维光子晶体波导与单模平面介质波导间的喇叭波导接头

提出并优化了用于二维介质柱光子晶体波导与单模平面介质波导对接的基于分布布拉格反射波导的喇叭波导接头，提高了这两种波导之间的传输效率.二维时域有限差分仿真结果表明，在大部分光子晶体波导导模的频谱范围内，传输效率高于98％.传输效率最高可以达到99.85％. 关键词： 光子晶体波导 平面介质波导 时域有限差分