Investigation of polymer/inorganic hybrid photovoltaic device using quantum dots as the interface modifier

CdS quantum dots (QDs) were introduced as an interface modifier in the poly(3-hexylthiophene) (P3HT)/TiO₂ nanorod arrays hybrid photovoltaic device. The presence of CdS QDs interlayer was found to provide enhanced light absorption, increased interfacial recombination resistance at the P3HT/TiO₂ interfaces, thus leading to a lower recombination rate of the electrons due to the stepwise structure of band edge in P3HT/CdS/TiO₂, which accounts for the observed enhanced photocurrent and photovoltage of the hybrid solar cells. The optimized performance was achieved in P3HT/CdS/TiO₂ hybrid solar cells after deposition of CdS QDs for 10 cycles, with a power conversion efficiency of 0.57 %, which is nearly ten times higher than that of P3HT/TiO₂. The findings indicate that inorganic semiconductor quantum dots provide effective means to improve the performance of polymer/TiO₂ hybrid solar cells.     

CdS quantum dot-sensitized ZnO nanorod-based photoelectrochemical solar cells

ZnO nanorods have been grown using ZnO seed layer onto ITO-coated glass substrates. CdS quantum dots have been deposited onto ZnO nanorods using simple precursors by chemical method and the assembly of CdS quantum dots with ZnO nanorod has been used as photo-electrode in quantum dot-sensitized solar cells. X-ray diffraction results show that ZnO seed layer, ZnO nanorods, and CdS quantum dot-sensitized ZnO nanorods exhibit hexagonal structure. The particle size of CdS nanoparticle is 5 nm. The surface morphology studied using scanning electron microscope shows that the top surface of the vertically aligned ZnO nanorods is fully covered by CdS quantum dots. The ZnO nanorods have diameter ranging from 100 to 200 nm. The absorption spectra reveal that the absorption edge of CdS quantum dot-sensitized ZnO nanorods shift toward longer wavelength side when compared to the absorption edge of ZnO. The efficiency of the fabricated CdS quantum dot-sensitized ZnO nanorod-based solar cell is 0.69% and is the best efficiency reported so far for this type of solar cells.     

Effect of ZnS layers on optical properties of prepared CdS/TiO<Subscript>2</Subscript> nanotube arrays for photocatalyst

The TiO₂ nanotube arrays (TiO₂ NTAs) prepared by re-oxidation were chosen as basement. The NTAs prepared through re-oxidation show smoother surface and more uniform tube mouth on large scale compared with the first as-grown one. We use successive ionic layer adsorption and reaction method to deposit quantum dots (ZnS and CdS) onto the sample successively. The findings reveal that two kinds of quantum dots (～10 nm) distribute regularly and the nanotube mouth is open. From the UV–Vis absorption spectrum of samples, the red shift occurs after the sedimentation of the two quantum dots, which proves that the double modification can expand the absorption to 650 nm. Among all specimens, the sample produced by co-deposition has the highest speed of catalytic efficiency of 90.7% compared with bare TiO₂ NTAs (52.9%) and just CdS QDs sensitized sample (65.8%). In the test of photocatalysis durability, the decay percentages of CdS/TiO₂ NTAs and ZnS/CdS/TiO₂ NTAs were 35.8 and 48.4%, respectively, which means that the ZnS passivation layer plays a crucial role in enhancing photocatalytic activities.     

ZnO/TiO2 core–shell heterojunction for CdS and PbS quantum dot-cosensitized solar cells

ZnO nanorods (NRs) with regular morphology were prepared through hydrothermal method, and the TiO₂ shell was assembled onto the surface of ZnO NRs by spin coating to the ZnO/TiO₂ core–shell heterojunction. CdS and PbS quantum dots (QDs) were used to cosensitize the ZnO/TiO₂ nanostructure by direct adsorption (DA) and successive ionic layer adsorption and reaction, respectively. SEM, TEM, and HRTEM images show that the samples possessed a rough surface and four lattice fringes indicating the successful synthesis of the ZnO/TiO₂/CdS/PbS composite structure. The ZnO/TiO₂(10T)/CdS/PbS sample showed a high absorption intensity at a broad range of wavelength to visible light region. The ZnO/TiO₂(10T)/CdS/PbS photoelectrode with QDSSCs showed the highest IPCE of 36.04% and photoelectric efficiency (η) of 1.59%; these values increased by approximately 550% and 150% compared with those of unsensitized ZnO (0.29%) and ZnO/TiO₂(10T) (1.04%) and about 146% and 120% compared with those of ZnO/TiO₂(10T)/CdS and ZnO/TiO₂(10T)/PbS, respectively. The fill factor was 0.36, and the photocurrent density (J_sc) and open circuit voltage (V_oc) reached the maximum values of 9.73 mA cm⁻² and 0.46 V, respectively.     

The Dynamic Resistance of CdS/CdSe/ZnS Co-Sensitized TiO2 Solar Cells

Quantum dots' sensitized solar cells (QDSSCs) can create the high-performance and low-cost photovoltaic in the future. In this study, we synthesized the film of TiO₂/CdS/CdSe/ZnS photoanodes by successive ionic layer adsorption reaction (SILAR) method. The absorption spectra, photoluminescent spectra and electrochemical impedance spectra (EIS) of the film TiO₂/CdS/CdSe/ZnS photoanodes show that the structure of energy levels in the conduction band (CB) of photoanode materials CdS, CdSe, and ZnS quantum dots (QDs) can absorb a great number of photons in each region and inject stimulated electrons quickly into the conduction band (CB) of TiO₂. Furthermore, we also studied the influence of the SILAR cycles on the dynamic resistance, the lifetime of electrons in QDSSCs through Nyquist and Bode.     

Enhanced cyclability of CdS/TiO2 photocatalyst by stable interface structure

CdS nanoparticles were in situ deposited on TiO₂ nanosheets and nanorods under hydrothermal conditions, respectively. The effect of CdS–TiO₂ interface structure on hydrogen production activity was mainly investigated under visible light irradiation. The results showed that the TiO₂ nanosheet-based CdS/TiO₂ showed a higher activity and a higher cyclability than the nanorod-based sample due to the stronger interaction of CdS with the (0 0 1) facets of TiO₂ than with the (1 0 1) facets. It was proposed that the strong interaction between CdS nanoparticles and TiO₂ nanosheets effectively refrains the recombination of electrons and holes.     

Two-step annealed CdS/CdSe co-sensitizers for quantum dot-sensitized solar cells

CdS/CdSe co-sensitizers on TiO₂ films were annealed using a two-step procedure; high temperature (300 °C) annealing of TiO₂/CdS quantum dots (QDs), followed by low temperature (150 °C) annealing after the deposition of CdSe QDs on the TiO₂/CdS. For comparison, two types of films were prepared; CdS/CdSe-assembled TiO₂ films conventionally annealed at a single temperature (150 or 300 °C) and non-annealed films. The 300 °C-annealed TiO₂/CdS/CdSe showed severe coalescence of CdSe QDs, leading to the blocked pores and hindered ion transport. The QD-sensitized solar cell (QD-SSC) with the 150 °C-annealed TiO₂/CdS/CdSe exhibited better overall energy conversion efficiency than that with the non-annealed TiO₂/CdS/CdSe because the CdSe QDs annealed at a suitable temperature (150 °C) provided better light absorption over long wavelengths without the hindered ion transport. The QD-SSC using the two-step annealed TiO₂/CdS/CdSe increased the cell efficiency further, compared to the QD-SSC with the 150 °C-annealed TiO₂/CdS/CdSe. This is because the 300 °C-annealed, highly crystalline CdS in the two-step annealed TiO₂/CdS/CdSe improved electron transport through CdS, leading to a significantly hindered recombination rate.     

Effect of CdS modification on photoelectric properties of TiO2/PbS quantum dots bulk heterojunction

TiO₂/PbS(CdS) quantum dots (QDs) bulk heterojunction has been fabricated by successive ionic layer adsorption and reaction method via alternate deposition of PbS and CdS QDs. In comparison with TiO₂/PbS heterojunction, the incident photon to current conversion efficiency was increased almost 50% in the visible region. Meantime, the short-circuit current and open-circuit voltage were enhanced 200% and 35% respectively. The influence mechanism of CdS is related to reduction of trap state density at TiO₂/PbS interface and PbS QDs surface by the discussion of the dark current density–voltage curves, the transient photocurrent response curves and the electrochemical impedance spectra spectroscopy (EIS).     

ZnS overlayer on in situ chemical bath deposited CdS quantum dot-assembled TiO2 films for quantum dot-sensitized solar cells

ZnS overlayers were deposited on the CdS quantum dot (QD)-assembled TiO₂ films, where the CdS QDs were grown on the TiO₂ by repeated cycles of the in situ chemical bath deposition (CBD). With increasing the CdS CBD cycles, the CdS QD-assembled TiO₂ films were transformed from the TiO₂ film partially covered by small CdS QDs (Type I) to that fully covered by large CdS QDs (Type II). The ZnS overlayers significantly improved the overall energy conversion efficiency of both Types I and II. The ZnS overlayers can act as the intermediate layer and energy barrier at the interfaces. However, the dominant effects of the ZnS overlayers were different for the Types I and II. For Type I, ZnS overlayer dominantly acted as the intermediate layer between the exposed TiO₂ surface and the electrolyte, leading to the suppressed recombination rate for the TiO₂/electrolyte and the significantly enhanced charge-collection efficiency. On the contrary, for Type II, it dominantly acted as the efficient energy barrier at the interface between the CdS QDs and the electrolyte, leading to the hindered recombination rate from the large CdS QDs to the electrolyte and thus enhanced electron injection efficiency.     

TiO<Subscript>2</Subscript> Nanorod Arrays Sensitized with CdS Quantum Dots for Solar Cell Applications: Effects of Rod Geometry on Photoelectrochemical Performance

CdS quantum dot (QD) sensitized TiO₂ nanorod array (NRA) film electrodes with different rod geometries were fabricated via a solvothermal route followed by a sequentialchemical bath deposition (S-CBD) process. By controlling the solution growth conditions, the rod geometries, especially the tip structures, of the TiO₂ NRAs were tuned. The results indicated that the vertically aligned hierarchical NRAs possessed conically shaped tip geometry, which was favorable for film electrodes due to the reduced reflectance, enhanced light harvesting, fast charge-carrier separation and transfer, suppression of carrier recombination, sufficient electrolyte penetration and subsequent efficient QD assembly. CdS QD sensitized TiO₂ NRA film electrodes with tapered tips exhibited an enhanced photoelectrochemical (PEC) performance, a photocurrent intensity of 5.13 mA/cm² at a potential of 0 V vs. saturated calomel electrode, an open-circuit potential of −0.68 V vs. saturated calomel electrode and an incident photon to current conversion efficiency (IPCE) of 22% in the visible-light region from 400 to 500 nm. The effects of rod geometry on the optical absorption, reflectance, hydrophilic properties and PEC performance of bare TiO₂ and CdS QD sensitized TiO₂ NRA film electrodes were investigated. The mechanism of charge-carrier generation and transfer in these CdS QD sensitized solar cells based on vertically aligned TiO₂ nanorods is discussed.     

Assembly,characterization, and photocatalytic activities of TiO<Subscript>2</Subscript> nanotubes/CdS quantum dots nanocomposites

The semiconductor quantum dots (QDs) can be very efficient to tune the response of photocatalyst of TiO₂ to visible light. In this study, CdS QDs formed in situ with about 8 nm have been successfully deposited onto the surfaces of TiO₂ nanotubes (TNTs) to form TNTs/CdS QDs nanocomposites by use of a simple bifunctional organic linker, thiolactic acid. The diffuse reflectance spectroscopy (DRS) spectra of as prepared samples showed that the absorption edge of the TNTs/CdS composite is extended to visible range, with absorption edge at 530 nm. The photocatalytic activity and stability of TNTs/CdS were also evaluated for the photodegradation of rhodamine B. The results showed that when TNTs/CdS QDs was used, photocatalytic degradation of RhB under visible light irradiation reached 91.6%, higher than 45.4 and 30.5% for P25 and TNTs, respectively. This study indicated that the TNTs/CdS QDs nanocomposites were superior catalysts for photodegradation under visible light irradiation compared with TNTs and P25 samples, which may find wide application as a powerful photocatalyst in environmental field.     

Synthesis and characterization of bamboo-like CdS/TiO<Subscript>2</Subscript> nanotubes composites with enhanced visible-light photocatalytic activity

In order to efficiently use the visible light in the photocatalytic reaction, a novel bamboo-like CdS/TiO₂ nanotubes composite was prepared by a facile chemical reduction method, in which CdS nanoparticles located in the TiO₂ nanotubes. The composition and structure of this nanocomposite were characterized by TEM, HRTEM, XRD, XPS, FTIR and UV-vis spectroscopy. This CdS/TiO₂ nanotubes composite exhibited much higher visible-light photocatalytic activity for the degradation of methylene blue than pure TiO₂ nanotubes and CdS nanoparticles, and the highest photodegradation efficiency after 6 h irradiation can reach 84.5%. It is inferred that the unique structure of CdS/TiO₂ nanotubes composites acts an important role for the improvement of their photocatalytic activity.     

Application of core-shell PEGylated CdS/Cd(OH)2 quantum dots as biolabels of Trypanosoma cruzi parasites

Semiconductor quantum dots are a promising class of materials in the labeling of biological systems. In the present study we show the marking pattern of Trypanosoma cruzi (T. cruzi) live parasites using PEGylated CdS/Cd(OH)₂ fluorescent nanocrystals. The analysis obtained by confocal fluorescence microscopy and transmission electron microscopy indicates that only the endocytic paths of parasites were labeled. The parasites were alive after the incubation with the CdS/Cd(OH)₂-PEG suspension. Labeling the T. cruzi with quantum dots can help to better understand the endocytosis process and also the cellular differentiation.     

Development of gel polymer electrolytes for application in quantum dot-sensitized solar cells

A methylcellulose–polysulfide gel polymer electrolyte has been prepared for application in quantum dot-sensitized solar cells (QDSSCs) having the configuration FTO/TiO₂/CdS/ZnS/SiO₂/electrolyte/Pt(cathode). The electrolyte with the composition of 30.66 wt.% methylcellulose, 67.44 wt.% Na₂S, and 1.90 wt.% sulfur exhibits the highest conductivity of 0.183 S cm^?1 with the lowest activation energy of 6.14 kJ mol^?1. CdS quantum dot sensitizers have been deposited on TiO₂ film via the successive ionic layer absorption and reaction (SILAR) method. The QDSSC fabricated using the highest conducting electrolyte and CdS QD prepared with five SILAR cycles exhibits a power conversion efficiency (PCE) of 0.78%. After deposition of zinc sulfide (ZnS) and silicon dioxide SiO₂ passivation layers, the PCE of the QDSSC with photoanode arrangement of TiO₂/CdS(5)/ZnS(2)/SiO₂ increased to 1.42%, an improvement in performance by 82%.     

Microstructural, optical and photocatalytic properties of CdS doped TiO2 thin films

CdS doped TiO₂ thin films (with CdS content=0, 3, 6, 9 and 12 at%) were grown on glass substrates. The X-ray diffraction analysis revealed that the films are polycrystalline of monoclinic TiO₂ structure. The microstructure parameters of the films such as crystallite size (D_ν) and microstrain (e) are calculated. Both the crystallites size and the microstrain are decreased with increasing CdS content. The optical constants have been determined in terms of Murmann's exact equations. The refractive index and extinction coefficient are increased with increasing CdS content. The optical band gap is calculated in the strong absorption region. The possible optical transition in these films is found to be an allowed direct transition. The values of E_g^opt are found to decrease as the CdS content increased. The films with 3 at% CdS content have better decomposition efficiency than undoped TiO₂. The films with 6 at% and 9 at% CdS content have decomposition efficiency comparable to that of undoped TiO₂, although they have lower band gap. The CdS doped TiO₂ could have a better impact on the decomposing of organic wastes.     

Synthesis and characteristics of multifunctional Fe3O4-SiO2-CdS magnetic-fluorescent nanocomposites

A luminescent superparamagnetic nanocomposite with an Fe 3 O 4-SiO 2-CdS structure is synthesized.Coated with a silica shell,Fe 3 O 4 nanoparticles and CdS quantum dots (QDs) are successfully assembled together.Analysed from the test results of X-ray diffraction (XRD),transmission electron microscopy (TEM),high resolution transmission electron microscopy (HRTEM),hysteresis loop,and photoluminescence (PL) spectrum,these nanocomposites exhibit superparamagnetic and photoluminescent properties.     

Characterization and relative sonocatalytic efficiencies of a new MWCNT and CdS modified TiO2 catalysts and their application in the sonocatalytic degradation of rhodamine B

TiO₂ nanoparticles modified with MWCNTs and CdS were synthesized by the sol–gel method followed by solvothermal treatment at low temperature. The chemical composition and surface structure of the CdS/CNT–TiO₂ composites were investigated by X-ray diffraction, specific surface area measurements, energy-dispersive X-ray spectroscopy, transmission electron microscopy, and scanning electron microscopy. Then a series of sonocatalytic degradation experiments were carried out under ultrasonic irradiation in the presence of CNT/TiO₂ and the CdS/CNT–TiO₂ composites. It was found that RhB was quickly and effectively degraded under different ultrasonic conditions. As expected, the nanosized CdS/CNT–TiO₂ photocatalyst showed enhanced activity compared with the non CdS treated CNT/TiO₂ material in the sonocatalytic degradation of RhB. The sonocatalyst CCTb with 34.68% contents of Ti heat treated at 500 °C for 1 h showed the highest sonocatalytic activity. The synergistic effect of the greater surface area and catalytic activities of the composite catalysts was examined in terms of their strong adsorption ability and interphase interaction by comparing the effects of different amounts of MWCNTs and CdS in the catalysts and their roles. The mechanism of sonocatalytic degradation over the CdS/CNT modified TiO₂ composites under different ultrasonic conditions was also discussed.     

Synthesis and Characterization of CdS/CISe Quantum Dots with Core–Shell Structure

Quantum dots have received great interest due to their excellent optoelectronic properties. However, the surface defects of quantum dots affect the carrier transport and ultimately reduce the photovoltaic efficiency. In this paper, a core–shell quantum dot by hot-injection method is prepared to grow a narrow-band semiconductor layer (CuInSe₂ (CISe) quantumdot) on the surface of a broad-band core material (cadmium sulfide (CdS) nanocrystal). The composition, structure, optical properties, and decay lifetime of CdS/CISe core–shells are investigated in more detail by X-ray diffraction (XRD), transmission electron microscopy (TEM), photoluminescence (PL), UV–vis spectrophotometry, and fluorescence spectroscopy. The CdS/CISe core–shell structure has a broadened absorption range and still shows CISe-related quantum effects. The increased size of the core–shell and the smaller specific surface area of the CISe shell layer lead to a lower carrier complexation chance, which improves the carrier lifetime.     

Effects of charging and doping on orbital hybridizations and distributions in TiO2 clusters

Charging and doping are two important strategies used in TiO₂ quantum dots for photocatalysis and photovoltaics. Using small clusters as the prototypes for quantum dots, we have carried out density functional calculations to study the size-specific effects of charging and doping on geometry, electronic structure, frontier orbital distribution, and orbital hybridization. We find that in neutral (TiO₂)_n clusters the charge transfer from Ti to O is almost size independent, while for the anionic (TiO₂)_n clusters the corresponding charge transfer is reduced but it increases with size. When one O atom is substituted with N, the charge transfer is also reduced due to the smaller electron affinity of N. As the cluster size increases, the populations of 3d and 4s orbitals of Ti decrease with size, while the populations of the 4p orbital increase, suggesting size dependence of spd hybridizations. The present study clearly shows that charging and doping are effective ways for tailoring the energy gap, orbital distributions, and hybridizations.     

Fabrication and characterization of CdS-sensitized TiO<Subscript>2</Subscript> nanotube photoelectrode

CdS quantum dot (Qd)-sensitized TiO₂ nanotube array photoelectrode is synthesised via a two-step method on tin-doped In₂O₃-coated (ITO) glass substrate. TiO₂ nanotube arrays are prepared in the ethylene glycol electrolyte solution by anodizing titanium films which are deposited on ITO glass substrate by radio frequency sputtering. Then, the CdS Qds are deposited on the nanotubes by successive ionic layer adsorption and reaction technique. The resulting nanotube arrays are characterized by scanning electron microscopy, X-ray diffraction (XRD) and UV–visible absorption spectroscopy. The length of the obtained nanotubes reaches 1.60 μm and their inner diameter and wall thickness are around 90 and 20 nm, respectively. The XRD results show that the as-prepared TiO₂ nanotubes array is amorphous, which are converted to anatase TiO₂ after annealed at 450 °C for 2 h. The CdS Qds deposited on the TiO₂ nanotubes shift the absorption edge of TiO₂ from 388 to 494 nm. The results show that the CdS-sensitized TiO₂ nanotubes array film can be used as the photoelectrode for solar cells.