Adsorptive Stripping Voltammetric Determination of Phenol at an Electrochemically Pretreated Carbon-Paste Electrode with Solid Paraffin as a Binder

An adsorptive stripping voltammetric method for determination of phenol at an electrochemically pretreated carbon-paste electrode has been developed. Solid paraffin was used as the binder of the carbon-paste electrode. The carbon-paste electrode was pretreated in the solution of 0.001 mol L⁻¹NaOH by holding it at +1.8 V (versus an Ag/AgCl electrode) for 5 min. On the pretreated electrode, the adsorption of phenol was greatly enhanced. Phenol was accumulated in NH₃–NH₄Cl (pH 9.25) medium at the potential of +0.1 V (versus Ag/AgCl electrode) for a certain time and then determined by second order differential anodic stripping voltammetry. An oxidative peak was observed at about +0.66 V. The relationship between second order peak current and phenol concentration was linear in the range of 2.5 × 10⁻⁷–5.0 × 10⁻⁶mol L⁻¹phenol, and the detection limit was 5.0 × 10⁻⁸mol L⁻¹. The method has been applied to the determination of phenol in tap water and waste water. The relative standard deviation (six determinations) was less than 3.5%.     

Determination of 4-methylbenzilidene camphor in sunscreen by square wave voltammetry in media of cationic surfactant

The voltammetric behavior of 4-methylbenzelidene camphor (MBC) was studied by square wave voltammetry (SWV) using mercury electrode. The experimental condition that provided the highest peak current with the best reduction signal definition of MBC was found in Britton-Robinson buffer and cationic surfactants, cetyltrimethylammoniun bromide (CTABr). A single peak of MBC reduction was observed at − 1.21 V versus Ag/AgCl. The developed methodology was applied for determination of MBC in commercial sunscreen SPF 15, 20 and 30 and for the simultaneous determination when other protection agents were associated, such as benzophenone-3 (BENZO) and octyl methoxycinammate (OMC). Both methodologies had shown good determination values for the analyzed samples. The calculated detection limit was 2.99 × 10^− 9 mol L^− 1 and the quantification limit was 9.98 × 10^− 9 mol L^− 1.     

Determination of Blasticidin S in Spiked Rice Using SW Voltammetry with a Renewable Silver Amalgam Film Electrode

Blasticidin S (BS) was determined in spiked rice samples by square wave voltammetry (SWV) and square wave stripping voltammetry (SWSV) using a cyclic renewable silver amalgam film electrode (Hg(Ag)FE). It was found that the compound can act as an electrocatalyst. In Britton? Robinson buffer at pH 7.0 a signal connected with the hydrogen evolution reaction was detected at ?1.2 V versus Ag/AgCl. Validation of the method was carried out. The detection and quantification limits were found to be 2.13×10^?8 mol L^?1; 7.10×10^?8 mol L^?1 for SWV and 2.65×10^?9 mol L^?1; 8.85×10^?9 mol L^?1 for SWSV, respectively.     

Sensitive Determination of the Diquat Herbicide in Fresh Food Samples on a Highly Boron‐Doped Diamond Electrode

The highly boron‐doped diamond electrode (HBDD) combined with square wave voltammetry (SWV) was used in the development of an analytical procedure for diquat determination in potato and sugar cane samples and lemon, orange, tangerine and pineapple juices. Preliminary experiments realised in a medium of 0.05 mol L^?1 Na₂B₄O₇ showed the presence of two voltammetric peaks around ?0.6 V and around ?1.0 V vs. Ag/AgCl/Cl^? 3.0 mol L^?1, where the first peak could be successfully used for analytical proposes due the facility in the electrode surface renovation. After the experimental and voltammetric optimisation, the calculated detection and quantification limits were 1.6×10^?10 mol L^?1 and 5.3×10^?10 mol L^?1 (0.057 µg L^?1 and 0.192 µg L^?1, respectively), which are lower than the maximum residue limit established for fresh food samples by the Brazilian Sanitary Vigilance Agency. The proposed methodology was used to determine diquat residues in potato and sugar cane samples and lemon, orange, tangerine and pineapple juices and the calculated recovery efficiencies indicated that the proposed procedure presents higher robustness, stability and sensitivity, good reproducibility, and is very adequate for diquat determination in complex samples.     

Study of the voltammetric behaviour of metam and its application to an amperometric flow system

The electrochemical behaviour of the pesticide metam (MT) at a glassy carbon working electrode (GCE) and at a hanging mercury drop electrode (HMDE) was investigated. Different voltammetric techniques, including cyclic voltammetry (CV) and square wave voltammetry (SWV), were used. An anodic peak (independent of pH) at +1.46 V vs AgCl/Ag was observed in MT aqueous solution using the GCE. SWV calibration curves were plotted under optimized conditions (pH 2.5 and frequency 50 Hz), which showed a linear response for 17–29 mg L⁻¹. Electrochemical reduction was also explored, using the HMDE. A well defined cathodic peak was recorded at −0.72 V vs AgCl/Ag, dependent on pH. After optimizing the operating conditions (pH 10.1, frequency 150 Hz, potential deposition −0.20 V for 10 s), calibration curves was measured in the concentration range 2.5×10⁻¹ to 1.0 mg L⁻¹ using SWV. The electrochemical behaviour of this compound facilitated the development of a flow injection analysis (FIA) system with amperometric detection for the quantification of MT in commercial formulations and spiked water samples. An assessment of the optimal FIA conditions indicated that the best analytical results were obtained at a potential of +1.30 V, an injection volume of 207 μL and an overall flow rate of 2.4 ml min⁻¹. Real samples were analysed via calibration curves over the concentration range 1.3×10⁻² to 1.3 mg L⁻¹. Recoveries from the real samples (spiked waters and commercial formulations) were between 97.4 and 105.5%. The precision of the proposed method was evaluated by assessing the relative standard deviation (RSD %) of ten consecutive determinations of one sample (1.0 mg L⁻¹), and the value obtained was 1.5%.     

Silver nanoparticle assemblies supported on glassy-carbon electrodes for the electro-analytical detection of hydrogen peroxide

Electrochemical detection of hydrogen peroxide using an edge-plane pyrolytic-graphite electrode (EPPG), a glassy carbon (GC) electrode, and a silver nanoparticle-modified GC electrode is reported. It is shown, in phosphate buffer (0.05 mol L^–1, pH 7.4), that hydrogen peroxide cannot be detected directly on either the EPPG or GC electrodes. However, reduction can be facilitated by modification of the glassy-carbon surface with nanosized silver assemblies. The optimum conditions for modification of the GC electrode with silver nanoparticles were found to be deposition for 1 min at –0.5 V vs. Ag from 5 mmol L^–1 AgNO₃/0.1 mol L^–1 TBAP/MeCN, followed by stripping for 2 min at +0.5 V vs. Ag in the same solution. A wave, due to the reduction of hydrogen peroxide on the silver nanoparticles is observed at –0.68 V vs. SCE. The limit of detection for this modified nanosilver electrode was 2.0×10^–6 mol L^–1 for hydrogen peroxide in phosphate buffer (0.05 mol L^–1, pH 7.4) with a sensitivity which is five times higher than that observed at a silver macro-electrode. Also observed is a shoulder on the voltammetric wave corresponding to the reduction of oxygen, which is produced by silver-catalysed chemical decomposition of hydrogen peroxide to water and oxygen then oxygen reduction at the surface of the glassy-carbon electrode.     

Determination of thorium by adsorptive type chemically modified electrode with a polycomplex system

A preconcentration and determination method for thorium in aqueous solution with a tri-n-octylphosphine oxide modified glassy carbon electrode is proposed. In the presence of 2-thenoyltrifluoroacetone, thorium in NaAc-HAc supporting electrolyte is preconcentrated on a modified rotating disk electrode, and a highly sensitive reduction peak is obtained by cathodic stripping voltammetry at –1.10 V versus Ag/AgCl. A linear response of reduction peak height and concentration is observed for 1.15×10^–9–1.44×10^–8 mol·1^–1 of thorium and the detection limit is 1.0×10^–9mol·1^–1. It is very selective and sensitive, with a standard deviation of 3.4% and a recovery of 90–110%.     

Determination of acipimox in capsules by differential pulse polarography

A differential pulse polarographic (DPP) method has been developed for the determination of acipimox in its pharmaceutical formulations. Using Sörensen buffer pH 6.0 as supporting electrolyte a single, irreversible peak occurred at –0.79 V vs an Ag/AgCl reference electrode. The peak height vs concentration plot was found to be linear over the range of 10^–6 to 6 × 10^–4 mol/l. The detection limit is 60ng/ml. The analysis of a series of 10 Olbetam® 250 mg capsules showed an overall standard deviation of ± 4.18 mg and a S_rel of ± 1.66%, respectively.     

A Novel Strategy for Quantifying Clopidogrel Using Square‐wave Voltammetry and a Boron‐doped Diamond Film

The voltammetric behavior of clopidogrel bisulfate (CLO), an antiplatelet agent, was investigated for the first time in the literature on a cathodically pretreated boron‐doped diamond electrode (CP‐BDDE) using cyclic (CV) and square‐wave voltammetry (SWV). It was observed an anodic peak for CLO, suitable for analytical purposes, at about 1.15 V (vs. Ag/AgCl (3.0 mol L^?1 KCl)) by CV in Britton‐Robinson buffer solution (pH 5.0). On the physical‐chemical characterization of the interface phenomena, it was proved that electrode reaction of the analyte was controlled by a diffusion process. At optimized square‐wave parameters (pulse amplitude of 60 mV, frequency of 30 Hz and scan increment of 3 mV), the obtained analytical curve was linear for the CLO concentration range from 0.60 to 60.0 μmol L^?1, with a detection limit of 0.60 μmol L^?1. The simple, rapid and greener analytical method, based on CP‐BDDE electrochemical sensor, was successfully applied in real samples (pharmaceuticals and urine).     

Voltammetric study of glibenclamide at carbon paste and Sephadex-modified carbon paste electrodes

The oxidative behaviour of the antidiabetic agent glibenclamide on a bare carbon paste electrode (CPE) and a Sephadex-modified carbon paste electrode (SMCPE) was explored by cyclic and differential pulse voltammetry (DPV). The analysis procedure consisted of an open circuit accumulation step in stirred sample solution of Britton-Robinson buffer (0.04 mol L^–1, pH 2.0). This was followed by medium exchange to a clean solution of Britton-Robinson buffer (0.04 mol L^–1, pH 5.0), and subsequently an anodic potential scan was effected to obtain the voltammetric peak. The glibenclamide oxidation peak current obtained by DPV was proportional to the concentration of the glibenclamide in the range of 1.0×10^–9 mol L^–1 to 5.0×10^–8 mol L^–1 for 180 s accumulation time, with a detection limit of 4.0×10^–10 mol L^–1. A method was developed for the determination of glibenclamide in formulation and spiked human serum. Moreover, the proposed procedure was used to estimate the serum concentrations after oral administration of a 5 mg tablet of glibenclamide to three diabetic subjects.     

Square-wave voltammetric determination of cefoperazone in a bacterial culture,pharmaceutical drug,milk, and urine

Use of square-wave voltammetry (SWV) for determination of cefoperazone (CFPZ) in some buffers, bacterial culture, urine, and milk is described. CFPZ provides a specific voltammetric signal which is affected by pH and solution components. Determination of CFPZ in Britton–Robinson buffer, pH 4.4, is sensitive with a low detection limit (about 0.5 nmol L^–1). In a more complex medium (bacterial 2YT medium, pH 7.2) the detection limit was approximately 1.5 mol L^–1. We provide evidence that SWV is a suitable and quick method for CFPZ determination in a culture of living bacteria without separation of biomass. We have found big differences between methicillin-resistant Staphylococcus aureus (MRSA) and methicillin-sensitive Staphylococcus aureus (MSSA) in cultivation in the presence of CFPZ, depending on time. When CFPZ is cleaved by penicillinase, a new SWV peak b appears at more positive potentials. This peak rises both with increasing concentration of enzyme and with cleavage time while the original CFPZ peak is simultaneously decreasing. We determined the concentration of CFPZ in the drug Pathozone by the standard addition method and achieved good agreement with the declared value of CFPZ in the drug. With a simple pretreatment procedure it is possible to determine CFPZ in milk; for urine no pretreatment was required. Using SWV we could detect CFPZ concentrations as low as 500 nmol L^–1 in bovine milk and human urine.     

Selective method for the determination of gold by anodic stripping voltammetry

A highly selective method for the deter- mination of gold by anodic stripping voltammetry is described. For preconcentration a glassy carbon electrode, activated by deposition of small amounts of gold before the measurement, is proposed. The Au³⁺ reduction process at such an electrode is effective starting with the potential +0.4 V vs. Ag/AgCl electrode. A linear dependence of the current of the gold stripping peak on the gold concentration was obtained in the range from 5×10^–8 to 1×10^–6 mol/l. The relative standard deviation for 2×10^-7 mol/l HAuCl₄ was 4.2% (n=5). The detection limit was 4×10^-9 mol/l. The accuracy of the method was verified by the determination of gold in reference materials.     

Electroanalytical Study of the Pesticide Ethiofencarb

Abstract

A detailed study of voltammetric behavior of ethiofencarb (ETF) is reported using glassy carbon electrode (GCE) and hanging mercury drop electrode (HMDE). With GCE, it is possible to verify that the oxidative mechanism is irreversible, independent of pH, and the maximum intensity current was observed at +1.20 V vs. AgCl/Ag at pH 1.9. A linear calibration line was obtained from 1.0×10^?4 to 8.0×10^?4 mol L^?1 with SWV method. To complete the electrochemical knowledge of ETF pesticide, the reduction was also explored with HMDE. A well‐defined peak was observed at –1.00 V vs. AgCl/Ag in a large range of pH with higher signal at pH 7.0. Linearity was obtained in 4.2×10^?6 and 9.4×10^?6 mol L^?1 ETF concentration range.

An immediate alkaline hydrolysis of ETF was executed, producing a phenolic compound (2‐ethylthiomethylphenol) (EMP), and the electrochemical activity of the product was examined. It was deduced that it is oxidized on GCE at +0.75 V vs. AgCl/Ag with a maximum peak intensity current at pH 3.2, but the compound had no reduction activity on HMDE.

Using the decrease of potential peak, a flow injection analysis (FIA) system was developed connected to an amperometric detector, enabling the determination of EMP over concentration range of 1.0×10^?7 and 1.0×10^?5 mol L^?1 at a sampling rate of 60 h^?1. The results provided by FIA methodology were performed by comparison with results from high‐performance liquid chromatography (HPLC) technique and demonstrated good agreement with relative deviations lower than 4%. Recovery trials were performed and the obtained values were between 98 and 104%.     

Electrochemical oxidation of methylthiomethyleneisoquinolinium chloride — the first water soluble alkylthiomethylene substituted ammonium salt

Electrochemical oxidation of methylthiomethyleneisoquinolinium chloride (MTMIQ), the first alkylthiomethyl substituted ammonium salt, which is fully miscible with water has been investigated by voltammetric (SWV) method using glassy carbon electrode. On the electrode, MTMIQ undergoes oxidation at the potential near Ep = 0.07V (vs. Ag/AgCl/3 M KCl). The influence of the pH of buffers, amplitude, frequency, step potential on the received signal was studied. The best results were obtained with a citrate buffer at a pH of 5. The oxidation peak current used for MTMIQ voltammetric determination was in the range of 2–8×10⁻⁵ mol L⁻¹, LOD = 3.7×10⁻⁶, LOQ = 1.2×10⁻⁵. The product of the oxidation was accumulated at the working electrode and was investigated by spectroscopic method. Mechanistic pathways of the oxidation have been proposed.      

Square‐Wave Voltammetry Applied to the Analysis of the Dye Marker,Solvent Blue 14, in Kerosene and Fuel Alcohol

The purpose of this paper is to develop an electroanalytical method based on square‐wave voltammetry (SWV) for the determination of the solvent blue 14 (SB‐14) in fuel samples. The electrochemical reduction of SB‐14 at glassy carbon electrode in a mixture of Britton‐Robinson buffer with N,N‐dimethylformamide (1 : 1, v/v) presented a well‐defined peak at?0.40 V vs. Ag/AgCl. All parameters of the SWV technique were optimized and the electroanalytical method presented a linear response from 1.0×10^?6 to 6.0×10^?6 mol L^?1 (r=0.998) with a detection limit of 2.90×10^?7 mol L^?1. The developed method was successfully utilized in the quantification of the dye SB‐14 in kerosene and alcohol samples with average recovery from 93.00 to 98.10%.     

Preconcentration and voltammetric determination of the herbicide metamitron with a silica-modified carbon paste electrode

A carbon paste electrode incorporating silica (Si-MCPE) was fabricated to accumulate Metamitron at the electrode surface. Several electroanalytical techniques were used to explore its reductive behaviour. The results indicate that the system is irreversible and fundamentally controlled by adsorption. The adsorptive stripping response has been evaluated with respect to accumulation time, deposition potential, scan rate, pH and other variables, using differential pulse voltammetry (DPV) and square wave voltammetry (SWV) as redissolution techniques. In both cases a voltammetric peak is obtained, at –0.542 V (DPV) and –0.421 V (SWV) in Britton-Robinson buffer (pH 1.9). The detection limits were 3.66 × 10^–1 M and 4.22 × 10^–9 M for AdS-DPV and AdS-SWV, respectively. Under optimum conditions the Metamitron reduction peak gave two linear regions in the range from 4.0 × 10^–9 M to 8.0 × 10^–8 M by means of AdS-DPV, with a coefficient of variation of 2.19% (n = 10) for 1 × 10^–8 M herbicide solution. A method was developed for determination of Metamitron in soils, with a recovery of 98.8% and a coefficient of variation of 5.26% (0.01 g/g of soil).     

Adsorptive stripping voltammetric measurements of trace amounts of platinum(II) and ruthenium(III) in the presence of 1-(2-pyridylazo)-2-naphthol

An extremely sensitive stripping voltammetric procedure for low level measurements of platinum (II, IV) or ruthenium (III, IV) is reported. The method is based on the interfacial accumulation of the platinum (II) or ruthenium (III)-1-(2-pyridylazo)-2-naphthol complex on the surface of a hanging mercury drop electrode, followed by the reduction of the adsorbed complex during the cathodic scan. The peak potential was found to be –0.8 V vs. Ag/AgCl electrode and the reduction current of the adsorbed complex ions of platinum (II) or ruthenium (III) was measured by differential pulse cathodic stripping voltammetry. The optimum experimental conditions were: 1.5×10^–7 mol/l of 1-(2-pyridylazo)-2-naphthol solution of pH 9.3, preconcentration potential of –0.2 V, accumulation time of 3 min and pulse amplitude of 50 mV with 4 mV s^–1 scan rate in the presence of ethanol-water (30% v/v) — sodium sulphate (0.5 mol/l). Linear response up to 6.4 × 10^–8 and 5.1 × 10^–8 mol/l and a relative standard deviation (at 1.2×10^–8 mol/l) of 2.4 and 1.6% (n=5) for platinum (II) and ruthenium (III) respectively were obtained. The detection limits of platinum and ruthenium were 3.2×10^–10 and 4.1×10^–10 mol/l, respectively. The electronic spectra of the Pt(II) — PAN and Ru(III) — PAN complexes were measured at pH 9.3 and the stoichiometric ratios of the complexes formed were obtained by the molar ratio method. The effects of some interfering ions on the proposed procedure were critically investigated. The method was found suitable for the sub-microdetermination of ruthenium (IV) and platinum (IV) after their reduction to ruthenium (III) and platinum (II) with sulphur dioxide in acid media. The applicability of the method for the analysis of binary mixtures of ruthenium (III) and (IV) or platinum (II) and (IV) has also been carried out successfully. The method is simple, rapid, precise, and promising for the determination of the tested metal ions at micro-molar concentration level.     

Determination of nanomolar levels of guanine by differential-pulse adsorptive cathodic stripping voltammetry of its copper(II) complex

Guanine is determined at the 5.0×10^–10 –2.0×10^–7 mol/l level by differential-pulse adsorptive stripping voltammetry at a hanging mercury drop electrode using the reduction peak of its copper (II) complex at –0.21 V vs. Ag-AgCl electrode. The optimum analytical conditions were found to be Britton-Robinson buffer solution (pH 4.8), an accumulation potential of 0.0 V and an accumulation time of 3 min. Under these conditions, the detection limit is 5.0×10^–10 mol/l and the relative standard deviation 2.6% for 1.0×10^–7 mol/l guanine. The method is compared with the previous voltammetric methods. The presence of some purine derivatives does not interfere.     

Electrocatalytic oxidation of thiosulfate on a modified nickel hexacyanoferrate film electrode

Summary A modified nickel hexacyanoferrate film glassy carbon electrode is prepared by the electrochemical deposition technique. The film is very stable upon voltammetric scanning in the potential range of 1.0 to –0.5 V (vs. SCE) and an oxidation peak occurs at 0.35 V (vs. SCE) (1 mol/l NaNO₃). The effects of electrolyte, solvent, coexisting ions and other variables on the voltammetric behaviour of the modified film have been studied. The thickness of the resulting film can be controlled by changing the number of voltammetric cycles and the concentrations of nickel(II) and hexacyanoferrate(III) ions. The film shows catalytic activity towards electrooxidation of thiosulfate with a peak potential +0.5 V (K^–-containing media). This oxidation potential of thiosulfate on the modified electrode is shifted negatively by about 550 mV as compared to the naked glassy carbon electrode. For practical application, the modified electrode can be used for the determination of thiosulfate in concentrations from 5.0×10^–5 to 1.0×10^–1 mol/l. This method has been successfully applied to the determination of thiosulfate in photographic waste effluents.     

Anodic stripping voltammetric determination of mercury using multi-walled carbon nanotubes film coated glassy carbon electrode

An electrochemical method for the determination of trace levels of mercury based on a multi-walled carbon nanotubes (MWNT) film coated glassy carbon electrode (GCE) is described. In 0.1 mol L^–1 HCl solution containing 0.02 mol L^–1 KI, Hg²⁺ was firstly preconcentrated at the MWNT film and then reduced at –0.60 V. During the anodic potential sweep, reduced mercury was oxidized, and then a sensitive and well-defined stripping peak at about –0.20 V appeared. Under identical conditions, a MWNT film coated GCE greatly enhances the stripping peak current of mercury in contrast to a bare GCE. Low concentrations of I^– remarkably improve the determining sensitivity, since this increases the accumulation efficiency of Hg²⁺ at the MWNT film coated GCE. The stripping peak current is proportional to the concentration of Hg²⁺ over the range 8×10^–10–5×10^–7 mol L^–1. The lowest detectable concentration of Hg²⁺ is 2×10^–10 mol L^–1 at 5 min accumulation. The relative standard deviation (RSD) at 1×10^–8 mol L^–1 Hg²⁺ was about 6% (n=10). By using this proposed method, Hg²⁺ in some water samples was determined, and the results were compared with those obtained by atomic absorption spectrometry (AAS). The two results are similar, suggesting that the MWNT-film coated GCE has great potential in practical analysis.