Analysis of the topochemical effects of dielectric-barrier discharge on cellulosic fibers

This study investigates the fundamental topochemical effects of dielectric-barrier discharge treatment on bleached chemical pulp and unbleached mechanical pulp fiber surfaces. Fibers were treated with various levels of dielectric-barrier discharge treatment ranging from 0 to 9.27 kW/m²/min. Changes to the fiber surface topochemistry were investigated by atomic force microscopy (AFM). The AFM studies were complemented by inverse gas chromatography (IGC), contact angle evaluation, poly-electrolyte titration, viscosity testing and determination of water retention value (WRV). The static coefficient of friction and zero-span tensile index of sheets were also evaluated. Low dielectric-barrier discharge treatment levels resulted in increased surface energy and roughness. Fibers treated at high applied power levels showed surface energies and roughness levels near that of reference samples as well as evidence of degradation and decreased fiber swelling.     

Sorption of dissolved galactoglucomannans and galactomannans to bleached kraft pulp

Sorption of mannans onto bleached kraft pulp (BKP) was investigated withreference to other interactions of mannans in mechanical pulping andpapermaking. O-Acetyl galactoglucomannans (GGM) isolated from thermomechanicalpulp (TMP), as well as enzymatically modified guar gum galactomannans (GM) wereused in the study. The results showed that deacetylation of TMP GGMs, alsooccurring during peroxide bleaching of TMP, dramatically increased thesorption.A higher sorption was also achieved after salt addition, while temperature hadno effect. Sorption of guar gum GMs onto BKP fibres was, on the other hand,quite unaffected by external conditions such as temperature, pH and saltaddition. The degree to which the pulp was beaten did not notablyinfluence the sorption either – only unbeaten pulp gave a clearly lower mannansorption. A lower number of galactose side groups, however, strongly affectedsorption – the lower the number of side groups, the higher the sorption.The molar mass did not seem to affect the rate of sorption to any higher extentat ambient temperature. At higher temperatures the rate of sorption of smallerGM polymers was, nevertheless, slightly increased. Low-molar-mass GMs alsosorbed at a higher rate onto unbeaten pulp compared to high-molar-mass mannans.GM sorption appeared to be virtually irreversible.     

Enzymatic surface modification of Kevlar fibers

Horseradish peroxidase catalyzed grafting of acrylamide (AM) onto Kevlar fibers has been studied. The modified fiber has been characterized with scanning electron microscopy (SEM), elemental analysis and the grafting yield. From the SEM micrographs, the surface of the grafted Kevlar fiber is rougher than that of the untreated fiber, and the elemental analysis indicated that the nitrogen content of the treated fibers is higher than that of the untreated fiber. All the results suggested that AM must have been grafted onto the Kevlar surface through HRP-mediated radical initiated grafting reaction. The probably mechanism of HRP catalyzed grafting of AM onto Kevlar surface is proposed.     

Enzymatic surface modification of Kevlar fibers

Horseradish peroxidase catalyzed grafting of acrylamide (AM) onto Kevlar fibers has been studied. The modified fiber has been characterized with scanning electron microscopy (SEM), elemental analysis and the grafting yield. From the SEM micrographs, the surface of the grafted Kevlar fiber is rougher than that of the untreated fiber, and the elemental analysis indicated that the nitrogen content of the treated fibers is higher than that of the untreated fiber. All the results suggested that AM must have been grafted onto the Kevlar surface through HRP-mediated radical initiated grafting reaction. The probably mechanism of HRP catalyzed grafting of AM onto Kevlar surface is proposed.     

Influence of Plasma Treatment on the Electroless Deposition of Copper on Carbon Fibers

Air and nitrogen glow discharge were used to replace chromic acid pretreatment to deposit copper film on carbon fiber surfaces from an CuSO₄‐HCHO electroless system. A greater copper uptake and a more uniformly coated copper film were obtained for plasma‐treated carbon fibers. The adhesion between the copper film and the carbon fibers was also improved. An orthogonal table L₉(3⁴) was used to study the effects of discharge pressure, discharge power, time and gas type on the copper uptake. Scanning electron microscopy (SEM), reflection absorption infrared spectroscopy (RAIR) and X‐ray photoelectron spectroscopy (XPS) at different depths were applied to characterize the physical and chemical changes of the surface of the carbon fibers. The results showed that after plasma treatment, the carbon fiber surface became rough and several types of polar oxygen groups, such as carboxylic acid COOH, esters COOC, quinones Ph?O, etc., were introduced into the carbon fiber surface. A mechanism of plasma treatment effects on copper electroless deposition on the carbon fiber surface is also suggested.     

Effects on surface properties of natural bamboo fibers treated with atmospheric pressure argon plasma

Argon plasma at atmospheric pressure was used to improve the wettability and dyeability of natural bamboo fibers. Optical emission spectroscopy (OES) was employed to characterize the discharge. SEM and scanning probe microscopy (SPM) analyses show that the fiber surface becomes rougher after plasma treatment because of the effects of plasma bombardment and etching. The wettability and dyeability are significantly enhanced after plasma treatment. Longer treatment time, leading to rougher surface, results in better surface wettability and dyeability. These results reveal that atmospheric pressure argon plasma treatment is an effective method to improve the performance of bamboo fibers. Copyright © 2006 John Wiley & Sons, Ltd.     

连续纤维增强含二氮杂萘酮联苯结构聚芳醚砜酮树脂基复合材料的界面

利用射频感性耦合冷等离子体(ICP)处理技术改性连续纤维表面,分别采用X射线光电子能谱(XPS)、原子力显微镜(AFM)及动态接触角分析(DCA)系统研究了等离子体处理时间、放电气压、放电功率等工艺参数对连续碳纤维、芳纶纤维和对亚苯基苯并二噁唑(PBO)纤维的表面化学成分、表面形貌、表面粗糙度及表面自由能的影响.研究结...     

Compacted UHMWPE fiber composites: Morphology and X‐ray microdiffraction experiments

The effect of compaction conditions on UHMWPE fibers is examined by microbeam X‐ray diffraction (WAXS) and scanning electron microscopy (SEM). The morphological observations indicate that melting occurs during compaction both on the surface of the fiber as well as in its internal regions. In addition, the recrystallized phase is nucleated on the fiber surface, possibly epitaxially. The recrystallized phase that originates from the internal regions of the fiber retains the initial highly oriented structure. WAXS microbeam measurements do not show any significant core‐shell structure in compacted single fibers. Considering the overall characteristics of the melting process during compaction, we can conclude that the hexagonal phase that appears upon heating of the fibers under moderate pressure is responsible for good adhesion of the fibers to each other, even more significantly than surface melting, especially because of its ability to retain the high orientation of the chains in the fibers. This information is relevant for understanding the formation and microstructure of the matrix component in the self‐reinforced composites fabricated by compaction. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1535–1541, 2007     

The surface characterization of styrene-acrylamide copolymer latex particles and their deposition onto fibers

The surface characteristics of styrene-acrylamide (St-AAm) copolymer latex particles were investigated and their deposition onto polyamide (Nylon 6), polyester (polyethylene terephthalate) and polyacrylonitrile fibers was studied. Conductometric titrations and viscosity measurements of latex dispersions revealed the presence of a water-soluble polymer layer on the particle surface and the thickness of its polymer layer increased with increasing acrylamide fraction in a latex particle. The deposition rates of St-AAm copolymer latices onto Nylon 6 and polyester fibers increased with increasing acrylamide fraction and decreasing pH at a constant ionic strength. These deposition phenomena onto Nylon 6 and polyester fibers agreed qualitatively with prediction based on the electrokinetic data of the latices and the fibers. However, a participation of attractive interaction due to an increase in acrylamide fraction was also suggested.The deposition rate onto polyacrylonitrile fiber decreased with increasing acrylamide fraction in spite of a decrease in electrostatic repulsive interaction, and it was found that a specific large repulsive interaction acts between polyacrylonitrile fiber and St-AAm copolymer latex particles.This paper is part VIII in a series on Interfacial electrical studies on the deposition of polymer latexes onto fabrics and the removal of these deposited latexes. Part VII: Tamai H, Kimura I,Suaza T Coll Polym Sci 261: 661 (1983)     

Adsorption of cationic copolymer nanoparticles onto bamboo fiber surfaces measured by conductometric titration

Monosized nanoparticles of 57.3 nm were prepared by cationic emulsion polymerization using a polymerizable emulsifier DMHB. The adsorption of nanoparticles onto bamboo fibers was measured by conductometric titration. The results indicated that the adsorption capacity increased with increasing contact time until 120 min. The equilibrium data for nanoparticles adsorption onto bamboo fibers were well fitted to the Langmuir equation. Moreover, the monolayer adsorption capacity of nanoparticles in the concentration range (from 0.03 g/L to 0.6 g/L) studied, as calculated from Langmuir isotherm model at 25℃, was found to be 38.61 mg/g of fibers. The SEM images showed that the nanoparticles form a uniform monolayer on bamboo fiber surfaces.     

Properties and treatments of pulps from recycled paper. Part II. Surface properties and crystallinity of fibers and fines

Surface properties of bleached kraft pulps were evaluated before and after recycling, and after a series of chemical treatments designed to improve and/or modify the pulp characteristics. The surface free energy characteristics of the pulps were determined using the Wilhelmy technique, and ESCA and ATR-FTIR methods were used to evaluate the chemical composition of the surfaces of the pulp fibers. In general rather small changes were noted at the fiber surfaces with recycling and chemical treatment. Recycling tended to increase the acid component and decrease the base component of the surface free energy of the pulps. This could result from exposure of carboxyl groups from hemicelluloses and/or from oxidized layers from the bleaching process. ESCA analyses also indicated increased carboxyl concentration at the surfaces of the recycled fibers. Although treatment with aqueous bases and organic solvents tended to increase the hydroxyl content on the surface of recycled pulps, the chemical treatments were not beneficial to pulp quality. AFM and SEM of fiber and fine surfaces of kraft pulps revealed that the fines fraction was altered to a much greater extent with recycling. Although recycled fibers appeared to have improved wettability, these small changes in the surface characteristics do not appear to play the dominant role in the characteristics of recycled pulps. Recycling did not change the crystallinity of whole pulps, but it increased the crystallinity of the fines fraction. The increase in the crystallinity of the fines fraction and the reduction in the water retention value (WRV) and the bulk carboxyl content (xylan) of the recycled pulps, as noted in Part I of this paper, appear to play the predominant role in determining the characteristics of recycled pulps. It appears that the loss of the hemicelluloses in the bulk of the fiber with recycling is much more important for internal fibrillation than the apparent small increase of hemicelluloses at the surface of recycled fibers.     

Surface modification of polyethylene fiber by graft polymerization

To improve the wettability and adhesion, graft polymerization of acrylamide (AAm) and glycidyl methacrylate (GMA) was performed onto the surface of ultra-high modulus polyethylene (UHMPE) fiber pretreated with Ar plasma. Following the plasma treatment and the subsequent exposure to air to introduce peroxides onto the fiber surface, graft polymerization onto the UHMPE fiber was allowed to proceed from the polymer peroxides either in deaerated monomer solution at an elevated temperature (degassing method), or in aerated monomer solution containing riboflavin at 30°C under UV irradiation (photoinduction method). The monomer solution was prepared from water and dioxane for AAm and GMA, respectively. After rigorous removal of homopolymers, surface analysis of the grafted fibers was performed with ATR-FTIR and XPS, which revealed that PAAm and PGMA chains were grafted in the surface region of fibers. The grafting rate of PAAm by the photoinduction method was much higher than that by the degassing method when compared at the same concentration of the AAm solution. The amount of PGMA grafted was greatly affected by UV irradiation time, but depended on plasma treatment time to an insignificant extent if the treatment was carried out for longer than 30 s. Reaction of propylamine with the PGMA-grafted surface resulted in the appearance of a nitrogen peak in the XPS spectrum, suggesting the presence of epoxy groups on the surface of PGMA grafted fiber. © 1994 John Wiley & Sons, Inc.     

Banana fiber-reinforced biodegradable soy protein composites

Banana fiber, a waste product of banana cultivation, has been used to prepare banana fiber reinforced soy protein composites. Alkali modified banana fibers were characterized in terms of density, denier and crystallinity index. Fourier transformed infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA) were also performed on the fibers. Soy protein composites were prepared by incorporating different volume fractions of alkali-treated and untreated fibers into soy protein isolate (SPI) with different amounts of glycerol (25%–50%) as plasticizer. Composites thus prepared were characterized in terms of mechanical properties, SEM and water resistance. The results indicate that at 0.3 volume fraction, tensile strength and modulus of alkali treated fiber reinforced soy protein composites increased to 82% and 963%, respectively, compared to soy protein film without fibers. Water resistance of the composites increased significantly with the addition of glutaraldehyde which acts as cross-linking agent. Biodegradability of the composites has also been tested in the contaminated environment and the composites were found to be 100% biodegradable.     

Surface modification of lignocellulosic fibers using high-frequency ultrasound

Enzymatic and chemical oxidation of fiber surfaces has been reported in the literature as a method for producing medium density fiberboards without using synthetic adhesives. This work focuses on modifying the surface properties of wood fibers by the generation of free radicals using high-frequency ultrasound. A sonochemical reactor operating at 610 kHz is used to sonicate the aqueous suspensions of thermomechanical pulp fibers (TMP). TMP is analyzed using FTIR-transmission, FTIR-ATR spectroscopy and inverse gas chromatography (IGC). The non-conjugated carbonyl groups in TMP are represented by the peak area ratio A₁₇₃₆/A₁₅₁₁ in the FTIR-transmission spectra and by A₁₇₂₈/A₁₅₀₉ in the FTIR-ATR spectra. The increase in these ratios suggests that there is an increase in the number of non-conjugated carbonyl groups in TMP after sonication. To further investigate, sonication of the hydrolytic lignin was also carried out and analyzed using UV, UV-ionization and FTIR-transmission spectroscopy. The changes in the surface properties of the fibers are analyzed using IGC which showed an increase in the surface free energy of fibers. The effect of operating parameters such as power of ultrasound and sonication time is also studied.     

Chemical characterization and ultrastructure study of pulp fibers

Understanding the ultrastructure and chemical characterization of pulp fibers is highly important in utilizing wood as a raw material in a wide scope of applications, such as forest biomass-based biorefineries and low-cost renewable materials. The observation of the ultrastructure is not possible without advanced microscopy and spectroscopy techniques. Therefore, this study focuses on exploring the ultrastructure of pulp fibers with helium ion microscopy (HIM) and scanning electron microscopy (SEM). For the analysis of chemical characterization in the pulp fibers, Raman spectroscopy, Fourier transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS) were performed. For these studies, the pulp fiber samples were obtained mainly from three different wood species, i.e. spruce, birch and eucalyptus. They were received in the never dried state and dried with a critical point drier (CPD) to minimize pore collapse. The spectroscopy results showed a strong signal from crystalline cellulose and confirmed the absence of lignin after Kraft pulping and bleaching. However, with XPS about 2% of lignin was detected in eucalyptus pulp. The results obtained with the microscopy techniques are compared and indicating the nanofibril size, shape, surface roughness as well as their orientation in pulp fibers. To our knowledge, this is the first time that HIM is applied to study the ultrastructure of pulp fibers and compared against more conventional microscopy and spectroscopy techniques. The main differences between HIM and SEM were found to be related to the focusing and magnification. The individual nano- and microfibrils as well as their bundles were more easily visible with HIM than with SEM. Also, with HIM it was possible to get the total area in focus at once which was not the case with SEM. The increased understanding of the ultrastructure and chemical composition of wood pulp enhance the development of novel wood-based products and processes for their manufacture.     

Alignment effect of attapulgite on the mechanical properties of poly(vinyl alcohol)/attapulgite nanocomposite fibers

Poly(vinyl alcohol) (PVA)/attapulgite (AT) nanocomposite fibers have been prepared by wet spinning. The morphology and mechanical properties of the modified PVA fibers have been characterized with transmission electron microscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), birefringence measurements, and mechanical testing. The PVA/AT nanocomposite fibers show much higher tensile strength, initial modulus, and work to break than pure PVA fibers with the same draw ratio. SEM observations demonstrate that the AT nanorods can align orderly along the fiber axis by stretching and have good adhesion to the fiber matrix. The results of birefringence measurements prove that the modified fibers have higher orientation than pure PVA fibers after stretching. The results of DSC analysis indicate that the crystallinity of the PVA fibers can be increased by the addition of AT. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1995–2000, 2006     

Surface methacrylation and graft copolymerization of ultrafine cellulose fibers

Ultrafine fibrous (? from 100 to 450 nm) cellulose membranes were generated by electrospinning of cellulose acetate [degree of substitution (DS): 2.45, weight‐average molecular weight: 30,000 Da], followed by alkaline deacetylation. Reaction of these ultrahigh surface‐area cellulose fibers with methacrylate chloride (MACl) produced activated surfaces without altering the fiber morphology. Surface methacrylation of these fibers was confirmed by the acquired hydrophobicity (θ_water = 84°) as compared to the originally hydrophilic (θ_water = 56°) cellulose. Changing the MACl:OH molar ratios could vary the overall DS of methacrylation. The very low overall DS values indicate the surface nature of the methacrylation reaction. At a DS of 0.17, the thermal properties of the surface methacrylated cellulose resemble those of cellulose derivatives at much higher DS values, an unusual behavior of the ultrafine fibers. The methacrylated cellulose could be further copolymerized with vinyl monomers (methyl methacrylate, acrylamide, and N‐isopropylacrylamide) as linear grafts or three‐dimensional (3D) networks. The morphology of cellulose fibers and the interfiber pore structure were not altered at 15–33% graft levels. This study demonstrates that either linear or 3D networks of vinyl polymers could be efficiently supported on ultrafine cellulose fibrous membranes via surface methacrylation. Through these surface reactions the chemical, thermal, and liquid wetting and absorbent properties of these ultrafine fibrous membranes were significantly altered with no change to the fiber dimensions or interfiber pore morphology. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 953–964, 2003     

Surface properties of CTMP fibers modified with xylans

This study investigated the effect of modification with xylan on the surface properties of chemithermomechanical pulp (CTMP) from spruce. The surface modifications were carried out by controlled sorption of birch xylan from solution at high temperature and high pH. Several different analysis techniques were used to study the effects on fiber surface composition and morphology. The ESCA technique showed a reduction in the amount of carbons not bound to oxygen in the C(1s) resolved peak after treatment. Variations in surface topography between untreated samples and samples with xylan were studied with SEM and AFM in the tapping mode. Scanning electron micrographs show micrometersized xylan particle structures spread over the fiber surfaces. AFM images reveal differences in the fine structure of fibers. The modified fibers exhibit a nanometersized, bumplike morphology not seen on the untreated fibers. The wetting properties of single fibers were determined with the Wilhelmy plate technique and the water sorption of CTMP paper sheets was studied using a dynamic contactangle tester. The surface modification of CTMP with xylan significantly decreased the advancing contact angle of single fibers and also improved the water sorption of sheets.     

The effect of silane concentration on the adsorption of poly(vinyl acetate-co-maleate) and γ -methacryloxypropyl- trimethoxysilane onto E-glass fibers

The adsorption of a poly(vinyl acetate-co-maleate) (PVAM) emulsion onto E-glass fibers was investigated along with sizing formulations prepared by mixing the PVAM with varying concentrations of -methacryloxypropyltrimethoxysilane (MPS). The sized E-glass fibers were then characterized using Diffuse Reflectance Infrared Fourier Transform (DRIFT) spectroscopy, X-ray Photoelectron Spectroscopy (XPS) and Scanning Electron Microscopy (SEM). Loss on Ignition (LOI) along with the DRIFT spectra indicated that the addition of silane to the PVAM emulsion caused a decrease in the amount of size on the fiber. The decrease in amount of size on the E-glass fibers did not coincide with a decrease in surface coverage, instead the XPS results indicated surface coverage had increased with silane addition. These results showed that small increases in the silane concentration appear to affect the amount of size adsorbed to the E-glass fibers     

Surface selective removal of xylan from refined never-dried birch kraft pulp

In this study, the effect of enzyme treatment on refined, never-dried bleached birch kraft pulp was investigated, using an endo-1,4-β-xylanase, that is substantially free from cellulase activity. The xylanase treatment of refined never-dried pulp revealed a rapid initial hydrolysis rate with a time-dependent saturation level in the amount of hydrolyzed pulp carbohydrates. Surprisingly short xylanase treatment times were found to have an impact on the fiber surface structure and on the physicochemical properties of kraft pulp fibers. Xylanase treatment led to mild microscopic differences in the ultrastructure of a never-dried fiber, whereas local topographical differences were distinguishable with atomic force microscopy. Results from the analysis of dissolved carbohydrates and the interfacial properties of the xylanase-treated never-dried fibers thus confirm a selective removal of xylan from the fiber surfaces. The zeta-potential charge and dewatering properties of the pulp slurry, fiber morphology, and strength properties of the paper were affected, which is a concomitant of xylanase treatment. However, the papermaking properties of the fibers were mainly preserved with simultaneous improvement in the dewatering rate of the pulp. Thus, optimized xylanase treatment of refined bleached kraft pulp provides a fiber for papermaking or fiber modification purposes with a selectively modified chemical composition of the fiber surface layer.