Analysis of correlation between percolation concentration and elongation at break in filled electroconductive epoxy-based adhesives

Electrical conductivity and elongation at break of epoxy filled with electroconductive carbon black, graphite or with silver-coated basalt particles or fibres were investigated in this paper. Percolation concentrations were determined to be 14 vol% for epoxy/carbon black composites, 22 vol% for epoxy/graphite composites, 28-29 vol% for both epoxy/silver-coated basalt particles and fibres. The steepest increase in electrical conductivity and the most pronounced decrease in elongation at break occurs at similar filler concentration range for all investigated systems. A good correlation between phenomenological model, introduced in [J. Mater. Sci. Lett. 18 (1998) 1457] and experimental data for all investigated systems was observed.     

Carbon Fabric Reinforced Composites Based on Modified Epoxy Resins and Prediction of Their Strength Characteristics

The strength characteristics of composites based on four types of modified epoxy resins and reinforced with carbon fabric were studied as influenced by the filler content. The experimental and theoretical strength parameters of the composites were compared. The correlation between the adhesion strength at the polymeric binder-filler boundary and the impact resilience of the composites was evaluated; a procedure was proposed for predicting the impact resilience of the reinforced composites.     

Effects of hyperbranched poly(ester‐silane) as a coupling agent on the mechanical behavior of glass bead filled epoxy resin

Hyperbranched poly(ester‐silane)s (HPE‐Si, including HPE‐Si4 and HPE‐Si8) were synthesized for glass bead filled epoxy resins. The grafting reaction and the degree of grafting of HPE‐Si onto the surface of glass beads were characterized by Fourier transform infrared photoacoustic spectroscopy (FT‐IR‐PAS) and thermogravimetric analysis (TGA) measurements. The degree of grafting was calculated to be in the range 1.0–4.2% for different HPE‐Si treatments. The tensile strength and modulus of glass bead filled epoxy resins were found to increase with increasing filler content. Moreover, HPE‐Si4 series have the highest tensile strength and modulus at the same glass bead size and volume fraction in the composites compared with HPE‐Si8 series. The fracture toughness (K_1c) of specimens with different glass bead sizes (4.8 and 2.0 μm) has the same trend that changes with the filler content and the modification of the surface of glass beads. The investigation of the toughening mechanism using Irwin's model through the yield stress measurements suggest that the toughening mechanism for small glass bead filled resins does not involve matrix plasticity, whereas the toughening mechanism involving matrix shear banding for large glass bead filled resins with higher filler content (up to 10 wt%) was proposed. The morphology of the filled resins studied by scanning electron microscopy (SEM) showed that the interface compatibility between the glass beads and epoxy matrix was greatly improved by the treatment with HPE‐Si. Copyright © 2005 John Wiley & Sons, Ltd.     

EFFECT OF PROCESSING METHOD ON THE IMPACT STRENGTH OF POM/TPU/CaCO3 TERNARY COMPOSITES

Polyoxymethylene （POM）/elastomer/filler ternary composites were prepared, in which thermoplastic polyurethane （TPU） and inorganic filler, namely, CaCO3, were used to achieve balanced mechanical properties of POM. The dispersion and phase morphology of POM/elastomer/filler composites were found to depend largely on processing method, CaCO3 content in masterbatch and the filler size. Two processing methods were employed to prepare POM/elastomer/filler ternary composites. One is called the one-step method, in which elastomer and the filler directly melt blended with POM matrix. The other is called the two-step method, in which the elastomer and the filler were mixed to get masterbatch first, which was then melt blended with pure POM of different content. The effect of phase morphology and processing method on impact strength was investigated. It was found that the two-step method results in an increase in impact strength but not for the one-step method. Additionally, the impact strength of POM ternary composites decreases with the increase in the size of CaCO3 particles.     

Epoxy‐based composite adhesives: Effect of hybrid fillers on thermal conductivity,rheology, and lap shear strength

Thermal management is an important parameter in an electronic packaging application. In this work, three different types of fillers such as natural graphite powder (Gr) of 50‐μm particle size, boron nitride powder (h‐BN) of 1‐μm size, and silver flakes (Ag) of 10‐μm particle size were used for thermal conductivity enhancement of neat epoxy resin. The thermal properties, rheology, and lap shear strength of the neat epoxy and its composite were investigated. The analysis showed that the loading of different wt% of Gr‐based fillers can effectively increase the thermal conductivity of the epoxy resin. It has also been observed that the thermal conductivity of the hybrid filler (Gr/h‐BN/Ag) reinforced epoxy adhesive composite increased six times greater than that of neat epoxy resin composite. Further, the viscosity of hybrid filler reinforced epoxy resin was found to be increased as compared with its virgin counterpart. The adhesive composite with optimized filler content was then subsequently subjected to determine single lap shear strength. The degree of filler dispersion and alignment in the matrix were determined by scanning electron microscopy (SEM) analysis.     

Thermal and mechanical properties of particulate fillers filled epoxy composites for electronic packaging application

Epoxy composites containing particulate fillers‐fused silica, glass powder, and mineral silica were investigated to be used as substrate materials in electronic packaging application. The content of fillers were varied between 0 and 40 vol%. The effects of the fillers on the thermal properties—thermal stability, thermal expansion and dynamic mechanical properties of the epoxy composites were studied, and it was found that fused silica, glass powder, and mineral silica increase the thermal stability and dynamic thermal mechanical properties and reduce the coefficient of thermal expansion (CTE). The lowest CTE value was observed at a fused silica content of 40 vol% for the epoxy composites, which was traced to the effect of its nature of low intrinsic CTE value of the fillers. The mechanical properties of the epoxy composites were determined in both flexural and single‐edge notch (SEN‐T) fracture toughness properties. Highest flexural strength, stiffness, and toughness values were observed at fillers content of 40 vol% for all the filled epoxy composites. Scanning electron microscopy (SEM) micrograph showed poor filler–matrix interaction in glass powder filled epoxy composites at 40 vol%. Copyright © 2007 John Wiley & Sons, Ltd.     

Thermal properties enhancement of epoxy resins by incorporating polybenzimidazole nanofibers filled with graphene and carbon nanotubes as reinforcing material

Enhancement of thermal properties of epoxy resins was achieved by incorporation of polybenzimidazole (PBI) fibermats filled with carbon nanomaterials, prepared by the solution electrospinning technique. Different type of carbon nanostructures (carbon nanotubes, graphite flakes, graphene nanoplatelets and carbon black) were compared as fillers in polybenzimidazole fibers. The carbon-PBI-fibermats showed remarkable thermal transport properties and therefore, they were studied as thermal reinforcement material for epoxy composites. Mechanical and thermal properties of produced composites were evaluated and the effectiveness of different types of carbon fillers examined. Results showed that the produced carbon filled fibermats can be used effectively as a thermal reinforcing material in epoxy resins, offering several advantages.     

高性能环氧树脂/碳纳米管复合物的热分析研究

用差示扫描量热仪(DSC)、热失重分析仪(TGA)和动态力学热分析仪(DMTA)研究了多壁碳纳米管(MWNTs)/高性能4,4′-二氨基二苯甲烷四缩水甘油环氧树脂(TGDDM)/4,4′-二氨基二苯基砜(DDS)复合物的热性能.Kissinger和Flynn-Wall-Ozawa的非等温固化动力学研究发现,随着MWNTs含量的增加,复合物固化反应的活化能先减小后增大.TGA研究表明,MWNTs的添加对环氧树脂热稳定性影响很小.碳纳米管填充到TGDDM/DDS体系后,复合物的储存模量随着MWNTs含量的增加而增大,而玻璃化温度却随之减小.     

A novel polypropylene composite filled by kaolin particles with β-nucleation

Kaolin-filled polypropylene (PP) composites generally form α-crystal due to the effect of kaolin with α-nucleation. The transition from α- to β-nucleation of kaolin has been investigated, and a novel kaolin with β-nucleation (β-kaolin) and kaolin-filled PP composites with high β-crystal content were prepared first. The DSC and WAXD results indicated that the β-kaolin exhibits stronger β-nucleating ability than CaPA as β-nucleating agent for PP crystallization. It is found that the β-crystal content has been influenced little by filler contents in β-kaolin-filled PP composites. Mechanical properties and spherulitic morphology of filled PP composites was characterized. The synergistic effect of filler and β-crystal significantly improved impact strength of kaolin-filled PP composites.

     

Electrically conductive composites of polyethylene filled with polyamide particles coated with silver

New types of electrically conductive polymeric composites were prepared on a base of high-density polyethylene (HDPE) matrix filled with silver-coated polyamide (PA) particles. The electrical, mechanical and adhesive properties of those composites are reported in this paper. The percolation concentration of the filler within a matrix was found to be 4 vol.%. Composites filled with high filler content were highly electrically conductive; their electrical conductivity reached the value of 6.8 × 10² S cm⁻¹. Mechanical properties and rheology of these composites were discussed. The adhesive properties of the composites to metal sharply increased with an increase in the filler content.     

Effect of filler shape on mechanical properties of rigid polyurethane composites containing plant particles

The effect of types of fillers on mechanical properties of rigid polyurethane composite samples was investigated. Polyurethane (PU) composites were prepared using a molasses polyol (MP, a mixture of molasses and polyethylene glycol, Mw=200) diphenylmethane diisocyanate (MDI) and fillers. The following plant particles, bamboo powder, roast bamboo powder, wood meal, coffee grounds, ground coffee bean parchment and cellulose powder, were used as fillers. The mixture of MP and fillers was reacted with MDI by adding an adequate amount of acetone as a solvent. The content of fillers was defined as the ratio of filler weight to total weight of polyol and fillers. The filler content was varied from 10 to 90 wt%. Polyurethane (PU) composites were prepared using fillers with MP. Lengths of major axis and minor axis for each particle regarded as an ellipse were measured using an optical microscope. Averages of diameter and aspect ratio were derived for each plant particle. The relationships between these average values and the mechanical properties, such as strength and elastic modulus, determined by the compression tests were investigated. The effect of filler content was estimated using the apparent volume ratio which is determined as the ratio of the apparent volume of fillers to the reciprocal values of the apparent density of samples. The master curves of the relationships between the specific values of mechanical properties and the apparent volume ratio were obtained. It was found that the compression strength and the elastic modulus for composite samples with different fillers showed maximum values at average aspect ratio around 3. It was also found that the apparent volume ratio, where the mechanical properties showed maximums, decreases with increasing aspect ratio. Using master curves, it is possible to evaluate the mechanical properties of plant particle filled polyurethane composites are described.     

Influence of silica fillers during the electron irradiation of DGEBA/TETA epoxy resins, part III: Solid-state NMR investigations

The influence of silica fillers on chemical modifications of diglycidyl ether of bisphenol A/triethylene tetramine (DGEBA/TETA) epoxy resins induced by electron beam irradiation has been studied by ¹³C CP-MAS (Cross Polarisation and Magic Angle Spinning) NMR. Four kinds of silica filler were investigated: a pure micrometric silica, a treated micrometric silica, a pure nanometric silica and a treated nanometric silica. On the unirradiated epoxy resins, the magnetization transfer curves reveal structural differences due to the kind of silica fillers. A decrease of the epoxy network rigidity in the presence of nanometric silica fillers is shown. During irradiation, the formation of phenolic ends and enamine functions is confirmed. The slowing of the magnetization transfer of the pure and treated micrometric silica filled epoxy resin reveals an important decrease of the rigidity of these resins. On the pure and treated nanometric silica filled epoxy resins, reactions of the reactive species created by the irradiation in the epoxy resin and the silica particles surface are shown.     

Polylactide (PLA) and Highly Filled PLA - Calcium Sulfate Composites with Improved Impact Properties

Summary: Starting from gypsum as by-product of lactic acid fabrication process, novel high performance composites have been produced by melt-blending PLA and this filler after a previous specific dehydration performed at 500 °C for min. 1h. Due to PLA sensitivity towards hydrolysis, the utilization of β-anhydrite II (AII) as filler is a prerequisite. Characterized by attractive mechanical and thermal properties due to good filler dispersion throughout the polyester matrix, these composites are interesting in biodegradable rigid packaging or technical applications. Interestingly, tensile strength of PLA – AII composites proved remarkably high, e.g. higher than 35 MPa at 50 wt-% filler content. However a decrease of impact properties has been recorded. To increase the toughness of these composites while preserving high stiffness an impact modifier based on ethylene copolymer has been mixed with both the polymer matrix and AII by melt-compounding. The effectiveness of the impact modifier was confirmed in both neat PLA and AII-based composites. Addition of 5-10 wt-% impact modifier into highly filled composites (30 to 40 wt-% filler) leads to an attractively threefold increase of impact strength with respect to the compositions without modifier, remarkable thermo-mechanical performances and good filler dispersion.     

Preparation and crystallization of aluminum hydroxide-filled β-polypropylene composites

Aluminum hydroxide-filled polypropylene composites generally form α-crystal due to the strong heterogenous α-nucleation of filler. In order to utilize β-crystal PP with high toughness to prepare aluminum hydroxide-filled PP composites, the aluminum hydroxide-filled PP composites nucleated by calcium pimelate and PP composites filled by calcium pimelate-supported aluminum hydroxide were fabricated. The crystallization and melting behavior of filled composites were compared by differential scanning calorimetry. The influence of aluminum hydroxide contents on the β-crystal content in the filled PP composites was discussed. It is a novel effective method to prepare aluminum hydroxide-filled β-PP composites with calcium pimelate-nucleated aluminum hydroxide.     

超细颗粒填充高密度聚乙烯复合体的导电和流变学性质(英文)

制备了多壁碳纳米管、石墨和碳黑填充高密度聚乙烯(HDPE)复合体,研究了复合体的导电和流变学性质.利用隧道逾渗模型对关键指数分别为4.4、6.4和2.9的三种复合体的"非普适性"导电行为进行了解释.与此同时,考察了颗粒类型和含量,以及剪切速率对复合体流变学性质的影响.结果表明,复合体系的储能模量在低频区出现"第二平台",而复合黏度则表现出强烈的剪切变稀行为,标志着颗粒在聚合物内部发生聚集形成了网络结构.与石墨和碳黑填充复合体相比,具有更高纵横比的多壁碳纳米管填充复合体具有更高的储能模量和复合黏度.基于Guth-Smallwood理论结合有效介近似的G′r分析结果表明,填充HDPE复合体系的流变学逾渗阈值和导电逾渗阈值吻合良好.     

Enhanced thermal conductivity of epoxy–matrix composites with hybrid fillers

The results of thermal conductivity study of epoxy–matrix composites filled with different type of powders are reported. Boron nitride and aluminum nitride micro‐powders with different size distribution and surface modification were used. A representative set of samples has been prepared with different contents of the fillers. The microstructure was investigated by SEM observations. Thermal conductivity measurements have been performed at room temperature and for selected samples it was also measured as a function of temperature from 300 K down to liquid helium temperatures. The most spectacular enhancement of the thermal conductivity was obtained for composites filled with hybrid fillers of boron nitride–silica and aluminum nitride–silica. In the case of sample with 31 vol.% of boron nitride–silica hybrid filler it amounts to 114% and for the sample with 45 vol.% of hybrid filler by 65% as compared with the reference composite with silica filler. However, in the case of small aluminum nitride grains application, large interfacial areas were introduced, promoting creation of thermal resistance barriers and causing phonon scattering more effective. As a result, no thermal conductivity improvement was obtained. Different characters of temperature dependencies are observed for hybrid filler composites which allowed identifying the component filler of the dominant contribution to the thermal conductivity in each case. The data show a good agreement with predictions of Agari‐Uno model, indicating the importance of conductive paths forming effect already at low filler contents. Copyright © 2014 John Wiley & Sons, Ltd.     

The effect of surface coating of CNTs on the mechanical properties of CF‐filled HDPE composites

Mechanical properties of carbon fiber (CF) and carbon nanotube (CNT)‐filled thermoplastic high‐density polyethylene (HDPE) composites were studied with particular interest on the effects of filler content and fiber surface treatment by coupling agent. Surface‐treated CF‐filled HDPE composites increased their tensile strength and impact strength, which is further increased with the addition of CNT. SEM showed that CNT‐coating‐treated CF‐HDPE composites show better dispersion of the filler into the matrix, which results in better interfacial adhesion between the filler and the matrix. Copyright © 2014 John Wiley & Sons, Ltd.     

Thermal degradation of epoxy composites based on thermally expanded graphite and multiwalled carbon nanotubes

Thermal degradation of epoxy composites filled with various carbon materials (thermally expanded graphite, multiwalled carbon nanotubes) was studied. The dynamics of the thermal degradation of epoxy composites was evaluated by thermogravimetric analysis in the temperature range of 55–700°С (heating rate 10 deg min^–1) in an oxidizing medium. Carbon fillers were studied by scanning electron microscopy, transmission electron microscopy, and low-temperature nitrogen adsorption. The influence of the composite preparation procedure on its thermal stability was determined. The type of filler significantly influences the thermal oxidative degradation of the composites.     

Bioinspired Design Provides High‐Strength Benzoxazine Structural Adhesives

A synthetic strategy to incorporate catechol functional groups into benzoxazine thermoset monomers was developed, leading to a family of bioinspired small‐molecule resins and main‐chain polybenzoxazines derived from biologically available phenols. Lap‐shear adhesive testing revealed a polybenzoxazine derivative with greater than 5 times improved shear strength on aluminum substrates compared to a widely studied commercial benzoxazine resin. Derivative synthesis identified the catechol moiety as an important design feature in the adhesive performance and curing behavior of this bioinspired thermoset. Favorable mechanical properties comparable to commercial resin were maintained, and glass transition temperature and char yield under nitrogen were improved. Blending of monomers with bioinspired main‐chain polybenzoxazine derivatives provided formulations with enhanced shear adhesive strengths up to 16 MPa, while alloying with commercial core–shell particle‐toughened epoxy resins led to shear strengths exceeding 20 MPa. These results highlight the utility of bioinspired design and the use of biomolecules in the preparation of high‐performance thermoset resins and adhesives with potential utility in transportation and aerospace industries and applications in advanced composites synthesis.     

界面改性剂在聚丙烯／高岭土二相复合体系中的作用

从高岭土（Ｋａｏｌｉｎ）填充聚丙烯（ＰＰ）体系的界面分子设计入手，研究了界面改性剂对填料的分散性，聚丙烯基体的结晶行为，填充熔体流变性质以及材料力学性能的影响．结果表明，界面改性剂降低了填料的高表面能，改善了填料分散状况．界面改性剂的加入，填充熔体粘度接近纯聚丙烯数值．经界面改性剂处理后，填充材料缺口悬臂梁冲击强度随填料量的增加而急剧升高，在填料量为３０Ｗｔ％时，冲击强度达到４８０Ｊ／Ｍ，是未处理材料的十二倍，添加至填料量为５０ｗｔ％时，冲击强度没有明显降低．