Synthesis and formulation of vinyl-containing polyacids for improved light-cured glass-ionomer cements

Vinyl-containing poly(acrylic acid-co-itaconic acid) copolymers were synthesized and used to formulate light-curable cements containing reactive glass fillers (Fuji II LC). The conditions for light curing were studied and optimized. Effects of molecular weight (MW), grafting ratio, comonomer, liquid composition, powder/liquid (P/L) ratio, glass powder and aging were evaluated. The results show that the vinyl-containing glass-ionomer cements (GICs) prepared in this study exhibit higher compressive strength (CS, 225.6 MPa), diametral tensile strength (DTS, 28.4 MPa) and much higher flexural strength (FS, 116.4 MPa), as compared to commercial Fuji II LC GIC (186.6 in CS, 19.1 in DTS and 57.1 in FS). The optimal light-exposure time was found to be around 10 min, and concentrations of CQ and DC were 0.5% (by weight) and 1.0%, respectively. Effects of MW, grafting ratio, P/L ratio and content of polymer in the liquid formulation were significant. The highest strengths were found for the optimal formulations where the MW was 15,000 (weight average), grafting ratio 25 mol%, P/L ratio 2.7 and liquid composition 50:20:30. During aging, the cement showed an increase of strength over the first week and then no change for a month. SEM analysis suggests that more integrated microstructures and smaller glass particles can lead to higher FS and higher polymer content in GICs leads to tough fracture surface and plastic deformation.     

Synthesis of amino acid-containing polyacids and their application in self-cured glass-ionomer cement

Six methacrylate or acrylate derivatives of natural amino acids were synthesized and characterized. Based upon these monomers, six terpolymers [poly(acrylic) acid-co-itaconic acid-co-amino acid] were prepared and characterized. The synthesized polymers were used to formulate glass-ionomer cements (GICs) using Fuji II glass filler. The effects of the molecular weight (MW) and powder/liquid (P/L) ratio were evaluated. Scanning electron microscopy (SEM) was used to examine the fracture surfaces of the selected cement specimens. Results show that all the amino acid modified GICs exhibited higher compressive strengths (CS, 193-236 MPa) and much higher flexural strengths (FS, 55-71 MPa) as compared to commercial Fuji II GIC (191 in CS and 16 in FS). Both MW and P/L ratio affected the strength of the formed cement. It was important to find the optimal MW and P/L ratio to obtain the highest FS. In this study, optimized MW (number average) of the polyacids and P/L ratio were around 50,000 and 2.7/1, respectively. The microstructures of the fracture surfaces helped to explain the strength differences among the materials tested in the study. SEM analysis suggests that more integrated microstructures and fewer defects can lead to higher FS.     

PREPARATION AND EVALUATION OF ACRYLIC ACID,ITACONIC ACID,AND N-METHACRYLOYLGLUTAMIC ACID COPOLYMERS FOR USE IN GLASS-IONOMER TYPE DENTAL RESTORATIVES

A series of copolymers containing various molar ratios of acrylic acid, itaconic acid and N-methacryloylglutamic acid were prepared in aqueous solution, using standard free-radical polymerization conditions. Specimens for mechanical property studies were prepared by mixing water solutions of the copolymers (50:50, wt:wt) with a commercial, calcium-fluoroaluminosilicate glass powder, with curing or hardening achieved by salt-bridge formation. The glass powder used in the formulation(s) was the same as that used in Fuji II (GC America) glass-ionomer. The working and setting times of the various formulations were evaluated. The compressive strength was used as the basic screening property to find the optimum molar ratio of the three monomers. The diametral tensile strength, flexural strength and Knoop surface hardness of the cured materials were also determined. All mechanical properties were measured after the specimens were conditioned in distilled water for 7 days at 37°C. Based on the compressive strength (CS), poly (AA-co-IA-co-MGA) with a monomers ratio of 8:1:1, respectively, showed the highest CS (269.9 MPa). The 8:1:1 copolymer with different molecular weights were also prepared to evaluate the effect of MW on the compressive strength. The optimum MW copolymer gave a glass-ionomer having the compressive strength improved by 30%, compared to Fuji II (293.9 MPa vs. 224.9 MPa). The same polymer solution was also mixed with glass powders used in other commercial glass-ionomers, i. e., Ketac-Molar (ESPE, Seefeld, Germany), α-Fil and α-Silver (DMG, Hamburg, Germany) to produce conventional glass-ionomers test specimens. The mechanical properties of these materials were also obtained and compared to the Fuji II, Ketac-Molar, α-Fil and α-Silver controls.     

NEW MATRIX RESINS FOR GLASS POLYALKENOATES OR GLASS-IONOMERS WITH PENDANT AMINO ACID RESIDUES

The monomers N-acryloyl (AGA) and N-methacryloylglutamic acid (MGA) have been prepared and copolymerized with acrylic acid (AA) and itaconic acid (IA) to make polyelectrolytes for evaluation in glass polyalkenoates or glass-ionomers. It was shown that poly(AA-co-IA-co-AGA) and poly(AA-co-IA-co-MGA), having a monomers ratio, respectively, of 7:3:3 could be formulated with glass powders used in Fuji II (GC America), α-Silver (DMG-Hamburg), α-Fil (DMG-Hamburg) and Ketac-Molar (ESPE, Seefeld, Germany) to produce conventional glass-ionomers with improved compressive strength (CS), flexural strength (FS) and fracture toughness (FT), compared to Fuji II, α-Silver, α-Fil and Ketac-Molar controls. Since MGA is much easier to produce in high yields than AGA, it was important to show that MGA could be used as well as AGA to produce new matrix resins for glass-ionomers. Furthermore, we demonstrated that both the 7:3:3 AGA and MGA copolymers could be reacted with 2-isocyanatoethyl methacrylate (IEM) to produce intermediates useful for formulating visible light-curable (VLC) glass-ionomers with improved CS, FS and FT, compared to two com-mercial VLC materials Fuji II^TM LC and Vitremer^TM Tricure. Here again, it was found that MGA could be used as well as AGA to prepare improved materials. We also demonstrated that poly(AA-co-MGA) could be used to formulate glass-ionomers with improved properties. Further, we demonstrated that small amounts of MGA could be used as a reactive diluent in VLC formulations such as Fuji II^TM LC, Vitremer^TM Tricure, and an experimental VLC formulation to improve their mechanical properties, adhesion to tooth structure, and fluoride release.     

Formulation of Visible Light-Curable Glass-Ionomer Cements Containing N-Vinylpyrrolidone

Abstract

The best graft ratio of the light-curable N-vinylpyrrolidone (NVP) modified terpolymers (LC NVPM TPs) with the molar ratio of 8:2:1 (acrylic acid:itaconic acid:NVP) and the optimal formulation for this light-curable glass-ionomer cement, based on the best graft ratio, were determined. Statistical models were utilized to predict the optimal formulations. The terpolymer was prepared using a free-radical polymerization reaction. The LC NVPM TPs were produced by grafting 2-isocyanatoethyl methacrylate (IEM) onto the terpolymer. Cements were formed by both light-curing and the reaction with glass particles. Compressive strength was used as the basic screening property to find the optimal formulation. Diametral tensile and flexural strengths were also used to evaluate the mechanical properties. The strength values were recorded on the specimens conditioned in distilled water at 37&C for 24 hours or 7 days. The best graft ratio for IEM in this system was 15% of the terpolymer by a molar ratio. The optimal formulation was found to be at the weight ratio of 55:15:30 [LC NVPM TP:2-hydroxyethyl methacrylate (HEMA): H₂O]. Stress-strain curves showed that a relatively high amount of water in the formulation led to higher elastic modulus and proportional limit and lower malleability, whereas a relatively high amount of HEMA gave the opposite results. The light-curable NVP modified glass-ionomer cements showed statistically significantly higher values in compressive, diametral tensile, and flexural strengths than the commercial Vitremer^TM.     

SYNTHESIS OF POLY(ACRYLIC ACID-CO-ITACONIC ACID) IN CARBON DIOXIDE–METHANOL MIXTURES

ABSTRACT

High fluidity solvents, such as supercritical fluids, have several advantages over traditional solvents as polymerization media, such as offering a more environmentally-friendly reaction media, providing increased reaction rates, and simplifying the separation and purification of polymers. In this study, a traditional glass-ionomer polymer, poly(acrylic acid-co-itaconic acid) (PAA/IA) was synthesized by using mixtures of CO₂ and methanol as the reaction solvent and was characterized by ¹H-NMR, FT-IR, GPC, and viscometry. The mechanical and working properties of the glass-ionomer cements, prepared by mixing aqueous solutions of the polymers with Fuji II glass powder, were evaluated for compressive strength (CS), diametral tensile strength (DTS) and flexural strength (FS), as well as setting time and working time. The results showed that the polymerization reaction in CO₂/methanol mixtures was faster and had higher conversion than the polymerization reaction in water. The glass-ionomer formulations made from the copolymer prepared under SC conditions showed higher CS, comparable FS and DTS compared with those made from the same polymer prepared in water. Both of the synthesized copolymers had significantly higher CS and FS than Fuji II. The working properties of PAA/IA made in CO₂/methanol met the requirement of ANSI/ADA No. 96.     

Improved Flexural Strength of N-Vinyl-Pyrrolidone Modified Acrylic Acid Copolymers for Glass-Ionomers

Abstract

The flexural strengths of N-vinylpyrrolidone modified glass-ionomer cements were investigated. The optimal molar ratio of the monomers in copolymers, composed of the three components acrylic acid, itaconic acid and N-vinylpyrrolidone, was determined using a SAS statistical program. The copolymers were prepared using a free-radical polymerization process. The viscosities of aqueous solutions of these polymers were determined. Cements were formed by the reaction of these solutions with glass particles. Flexural strength (FS) was used as the basic screening property to find the optimum molar ratio. Statistical models were applied to predict the optimum molar ratios. All strength values were recorded on the specimens conditioned in distilled water at 37°C for 7 days. The optimal molar ratio for these copolymers was 7:1:3 for poly(acrylic acid-co-itaconic acid-co-N-vinylpyrrolidone), based on flexural strength and viscosity. The effect of molecular weight (MW) on FS was also evaluated. Copolymer with a MW of 10, 800 (M_n) showed 85% higher FS than the Ketac-Molar (KM) system, along with a reasonable working viscosity.     

Electrochemical Behaviors of Ascorbic Acid and Uric Acid in Ionic Liquid

Cyclic voltammetric measurements at platinum electrode have been carried out to investigate the electrochemical oxidation of ascorbic acid and uric acid in ionic liquid, [bmim][BF₄]. It is important that a typical redox couple of ascorbic acid was obtained and it is oxidized to dehydroascorbic acid in [bmim][BF₄]. However, there is no electron-transfer for uric acid and no electrochemical oxidation carried out in the same ionic liquid. It provides a new way to eliminate the interfering between ascorbic acid and uric acid in the study of the electrochemical behaviors for them.     

Effect of hydrothermal curing on early hydration of G-Oil well cement

G-Oil well cement has been cured under standard and hydrothermal conditions with different steam pressures and temperatures. Compressive strength, pore structure parameters, microstructure, and hydrated products were evaluated after 7 days curing by using SEM, MIP, and simultaneous TGA/DSC. Obtained results showed that 7 days aged sample cured under standard conditions has the highest compressive strength with compact pore structure and hydrated products similar to those found after hydration of Ordinary Portland cement. With increasing temperature and pressure from standard conditions (25 °C, 10125 Pa) to hydrothermal ones (150 °C and 0.3 MPa, 200 °C and 1.2 MPa), compressive strength has drastically decreased from 77.5 ± 2.0 to 20.5 ± 1.0 MPa due to the transformation of original hydrated products (C–S–H) to crystallized α-C₂SH and C₆S₂H₃. The crystallization has led, under hydrothermal curing, to the increase of permeability and pore structure depletion. The final compressive strength after curing for 7 days at 150 °C (51.8 ± 2.0 MPa) and 200 °C (20.5 ± 1.0 MPa), which significantly exceeds the recommended values of 3.45 MPa according to API to hold many casings of oil wells is questionable for application in geothermal ones.     

Voltammetric studies of the activity of an electrode made of a graphite-epoxy composite in redox reactions of ascorbic acid and hydroquinone

The potentials of the anodic peak of ascorbic acid oxidation and the potential differences of anodic and cathodic peaks (ΔE _p) of the hydroquinone/benzoquinone redox system at an electrode made of a graphite-epoxy composite are determined in weakly acidic and neutral supporting electrolytes by direct and cyclic voltammetry. The results obtained are compared with thermodynamic values and with the available values of these parameters at different solid electrodes for the above-mentioned redox systems. The effect of aging of the surface of electrodes made of graphite-epoxy composites on the potentials and peak currents of the anodic oxidation of ascorbic acid are studied. It is demonstrated that the regeneration of the electrode surface by mechanically cutting thin layers is important for reducing the δE _p value of the hydroquinone/benzoquinone redox system down to 28–30 mV in supporting electrolytes with pH 2.0 and 7.0. This value is typical of thermodynamically reversible electrode reactions involving two-electron transfer at 20–25°C.     

High-efficient surface tailoring via reverse atom transfer radical polymerization and reversible addition-fragmentation chain-transfer polymerization in an aqueous system initiated by a monocenter redox pair

The commonly used multi-center initiation methods always lead to the formation of quantities of homopolymer in the surface tailoring based on reverse atom transfer radical polymerization (ATRP) and reversible addition-fragmentation chain-transfer (RAFT) polymerization. In this study, a monocenter redox pair constructed of silica bearing tert-butyl hydroperoxide groups and ascorbic acid (SiO₂-TBHP/AsAc) was applied to substitute the commonly used initiation method of R-supported RAFT grafting polymerization. All the propagating radicals were restricted on the surface of solid particles during the whole procedure theoretically, resulting in a higher grafting efficiency of 95.1% combined with the “controllable” feature at 10 h. This redox pair was also used to initiate the reverse ATRP in miniemulsion successfully with a grafting efficiency of 86.3% at 10 h. The grafting efficiency obtained under this monocenter initiation method was significantly higher than that of the frequently reported surface modification by reverse ATRP and RAFT polymerization. In addition, the high-efficient surface tailoring was traced and confirmed by nuclear magnetic resonance, Fourier transform infrared, X-ray photoelectron spectroscopy, thermogravimetric analysis, transmission electron microscopy, and other analysis tests. The advantage of this monocenter redox pair will open a new avenue for the potential “high-efficient” surface tailoring of various materials.     

聚羧酸系高效减水剂合成工艺的优化研究

以甲基烯丙基聚氧乙烯醚(HPEG)和丙烯酸(AA)为单体,以过氧化氢-抗坏血酸(H2 O2-Vc)为氧化还原引发体系,以巯基丙酸(MPA)为链转移剂,共聚合成了HPEGAA型聚羧酸减水剂.研究了合成温度、酸醚比及引发剂用量对聚羧酸减水剂分散性能的影响.结果表明,聚羧酸减水剂的最佳合成工艺为:n(AA):n(HPEG)=...     

Characterization and application of an electrode modified by mechanically immobilized copper hexacyanoferrate

A newly modified electrode was prepared by mechanical immobilization of copper hexacyanoferrate (CuHCF) on a graphite electrode. The modified electrode was characterized by cyclic voltammetric experiments. The effect of different background electrolytes, pHs and scan rates on the electrochemical behaviour of the electrode has been evaluated. In NH₄Cl two reversible redox peaks were observed. The first redox peak corresponding to Cu⁺/Cu²⁺ is observed only in this medium. The second redox peak corresponds to the Fe(CN)₆ ^4–/Fe(CN)₆ ^3– couple. Both anodic peaks were used for catalytic oxidation of ascorbic acid. As the anodic current for catalytic oxidation was proportional to the amount of ascorbic acid, an analytical method was developed for the determination of ascorbic acid in commercial samples.     

NOVEL TRIMETHACRYLATES: SYNTHESIS,CHARACTERIZATION, AND EVALUATION OF NEW MONOMERS FOR IMPROVED DENTAL RESTORATIVES

ABSTRACT

Two novel trimethacrylates, i.e., 1,1,1-tri-[4-(methacryloxyethoxy)-phenyl] ethane (TMPE) and 1,1,1-tri-[4-(2-methyl-2-methacryloxyethoxy)-phenyl]ethane (TMMPE), have been synthesized by reacting methacryloyl chloride with the corresponding hydroxyl intermediates. Both trimethacrylate monomers, having a low viscosity of 11.5 and 13.1 Pa.S, respectively, were blended with TEGDMA at three different weight ratios, i.e., 90/10, 70/30, and 50/50. The mixtures were made visible light-curable (VLC) by the addition of camphorquinone (0.5 wt%) and N,N-dimethyl-aminoethyl methacrylate (1.0 wt%). In addition to evaluation as cured neat resins, VLC formulations with 70% by wt. of silanated microfiller were also prepared and evaluated. The control in both cases was a VLC formulation of BisGMA/TEGDMA (70/30 and 50/50 wt/wt). These new, formulated resins have both improved physical properties and higher double bond conversion than the BisGMA control, as well as decreased linear polymerization shrinkage (LPS). The neat resin having 70/30 (wt/wt) ratio of TMPE/TEGDMA (T7T3, Table 2) exhibited a compressive strength (CS) of 496 (±51) MPa compared to the 70/30 (wt/wt) ratio of BisGMA/-TEGDMA control having 425(±27) MPa. A filled resin having a 90/10 (wt/wt) ratio of TMPE/TEGDMA exhibited a flexural strength (FS) of 122.6(±23) MPa, compared with a similar filled BisGMA/TEGDMA (70/30, wt/wt) resin exhibiting 112.7(±19) MPa. These and other results suggest that these new trimethacrylates have potential application in formulating dental composites with improved performance.     

Remarkable Electrochemical Responses of Ferrocene/NaY Zeolite Composite modified Electrode Based on Hydrophobic Ionic Liquid

The ferrocene/NaY zeolite composites (Fc/NaY) are introduced on the surface of a glassy carbon electrode together with the hydrophobic ionic liquid 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆). The modified electrode thus constructed exhibits a pair of reversible redox peaks corresponding to ferrocene. Additionally the peak separation remains almost constant (58–75 mV) and the value of the ratio i_pa/i_pc is close to 1 for scan rates in the range from 10 to 1000 mV s^?1. The effects of the scan rate, aqueous supporting electrolytes, hydrophobic ionic liquid and the contents of ferrocene encapsulated by electrochemistry are investigated. The extrazeolite electron transfer process is discussed. Furthermore, the Fc/NaY/IL‐modified electrode shows good mediation towards oxidation of ascorbic acid, dopamine, hydroquinone, and catechol.     

Cerium/Ascorbic Acid/Iodine Active Species for Redox Flow Energy Storage Battery

In this study, we developed a novel cerium/ascorbic acid/iodine active species to design a redox flow battery (RFB), in which the cerium nitrate hexahydrate [Ce(NO₃)₃·6H₂O] was used as a positive Ce³⁺/Ce⁴⁺ ion pair, and the potassium iodate (KIO₃) containing ascorbic acid was used as a negative I₂/I⁻ ion pair. In order to improve the electrochemical activity and to avoid cross-contamination of the redox pair ions, the electroless plating and sol–gel method were applied to modify the carbon paper electrode and the Nafion 117 membrane. The electrocatalytic and electrochemical properties of the composite electrode using methanesulfonic acid as a supporting electrolyte were assessed using the cyclic voltammetry (CV) test. The results showed that the Ce (III)/Ce (IV) active species presented a symmetric oxidation/reduction current ratio (1.09) on the C–TiO₂–PdO composite electrode. Adding a constant amount of ascorbic acid to the iodine solution led to a good reversible oxidation/reduction reaction. Therefore, a novel Ce/ascorbic acid/I RFB was developed with C–TiO₂–PdO composite electrodes and modified Nafion 117–SiO₂–SO₃H membrane using the staggered-type flow channel, of which the energy efficiency (EE%) can reach about 72%. The Ce/ascorbic acid/I active species can greatly reduce the electrolyte cost compared to the all-vanadium redox flow battery system, and it therefore has greater development potential.     

High temperature properties of MDF composite based on calcium aluminate cement and polyvinyl alcohol

The macro-defect-free composites belong to the well-known group of promising materials consisting of inorganic binder and organic polymer. MDF composites exhibit unusual mechanical properties, especially the flexural strength that can reach over 200 MPa. Moreover, the MDF composites based on calcium aluminate cement have a good temperature resistance because of the Al₂O₃ content in the cement. This paper deals with the preparation and high temperature characterization of MDF composite based on calcium aluminate cement combined with polyvinyl alcohol that could enable its utilization as a refractory material in industrial kilns. The composition of the MDF mixture has been optimized for an easy high-shear processing and flexural strength of the resulting 7-days cured material has been studied under laboratory condition and after heating at 240, 300, 600, 1,000, and 1,500 °C. The structure changes during the heating have been observed by SEM and the course of processes during the heating has been investigated by TG–DTA–EGA, TMA and heating microscopy.     

Characterization and application of an electrode modified by mechanically immobilized copper hexacyanoferrate

A newly modified electrode was prepared by mechanical immobilization of copper hexacyanoferrate (CuHCF) on a graphite electrode. The modified electrode was characterized by cyclic voltammetric experiments. The effect of different background electrolytes, pHs and scan rates on the electrochemical behaviour of the electrode has been evaluated. In NH₄Cl two reversible redox peaks were observed. The first redox peak corresponding to Cu⁺/Cu²⁺ is observed only in this medium. The second redox peak corresponds to the Fe(CN)₆ ^4–/Fe(CN)₆ ^3– couple. Both anodic peaks were used for catalytic oxidation of ascorbic acid. As the anodic current for catalytic oxidation was proportional to the amount of ascorbic acid, an analytical method was developed for the determination of ascorbic acid in commercial samples. Received: 26 May 1998 / Revised: 15 March 1999 / Accepted: 20 March 1999     

Characterization and Evaluation of Thermal,Morphological, and Physicochemical Properties of Chemically Modified Lignocellulosic Biomass

A novel redox system, ascorbic acid-hydrogen peroxide, was employed to initiate graft copolymerization of ethyl acrylate and methyl methacrylate binary monomer mixtures onto Abelmoschus esculentus fibers at a temperature of 45°C for 90 min in an aqueous medium. Factors affecting grafting such as feed molarity and comonomer composition were investigated. Contrary to the lower affinity of methyl methacrylate for grafting on Abelmoschus fibers, a synergistic effect of ethyl acrylate on methyl methacrylate was observed when graft copolymers were prepared using different feed compositions (f_MMA). The percentage of grafting increased from 40.2% to 89.74% at 0.4 mole fraction of f_MMA. The graft copolymers were characterized by FT-IR, TGA, and SEM techniques.     

Preparation and properties of cementitious composites for geothermal applications

Three fiber-reinforced cement composites were prepared and cured in an autoclave for up to 168 h at 2 MPa of steam pressure in order to investigate the effect of hydrothermal curing on the alteration of pore structure, density, and formation and stability of hydrated products with time. Compressive strength was reviewed in connection with sample porosity. It was found that the time of autoclaving plays a crucial role in objective assessment of the durability of composites as potential candidates for geothermal applications. A mercury intrusion porosimeter Quantachrome Poremaster 60GT was used for the estimation of the pore structure parameters of composites. The thermal analysis method was used to identify different temperature ranges of cured samples?? thermal decomposition and to characterize the nature of hydrated products. Two kinds of products were formed. The first group consisted of calcium-silicate-hydrate (C-S-H), calcium-silicate-aluminate-hydrate (C-S-A-H), calcium-aluminate-hydrate (C-A-H), and calcium-carbonate (C-C) as a product of carbonation. The second group are chemically bond products, e.g. hydroxyapatite (Ca₅(PO₄)₃(OH)) and gibbsite (Al(OH)₃). These two hydroceramic products formed under hydrothermal conditions act also as binders and they can be useful as geothermal cement binders.