聚(偏氯乙烯-丙烯酸甲酯)-b-聚丙烯酸嵌段共聚物的胶束化行为

通过可逆加成-断裂链转移(RAFT)溶液聚合制备了不同组成的两亲性聚(偏氯乙烯-丙烯酸甲酯)-b-聚丙烯酸(PVDC-b-PAA)嵌段共聚物,采用动态光散射、表面张力仪和透射电镜等研究了PVDC-b-PAA共聚物在水溶液中的胶束化行为,结果表明采用N,N-二甲基甲酰胺溶解、水相渗析可实现PVDC-b-PAA共聚物的自组装,形成均一透明的胶束水溶液;随着亲水PAA嵌段含量的增加,PVDC-b-PAA共聚物的临界胶束浓度逐渐增大;PVDC-b-PAA共聚物自组装形成的胶束呈现典型的球状结构,胶束粒径在70.9~110.9 nm之间,粒径分布较窄;水相p H值影响PVDC-b-PAA共聚物胶束表面zeta电位及胶束的聚集行为,当水相p H值由3变为1,胶束表面由带负电荷变为带正电荷,胶束聚集程度和聚集体平均粒径显著增大,粒径分布变宽.     

二甲基二烯丙基氯化铵/丙烯酸共聚凝胶的辐射合成与性质研究

采用γ辐射溶液聚合法合成了几种二甲基二烯丙基氯化铵 丙烯酸 (DADMAC AA)共聚凝胶 .实验结果表明单位体积溶液中二组分单体总摩尔数和丙烯酸 (AA)相对含量的增加使共聚凝胶力学强度明显增高 .在两种单体等摩尔比的情况下共聚体的凝胶含量随剂量增加而增加 ,且明显高于聚N ,N′ 二甲基二烯丙基氯化铵 (PolyDADMAC)凝胶 .体系中少量κ 卡拉胶 (KC)的加入可增强共聚凝胶韧性但对凝胶含量和强度影响甚微 .共聚凝胶溶胀性能测定结果表明DADMAC与AA摩尔比为 1∶2时凝胶溶胀比与体系pH值的关系呈现聚两性电解质性质 ,等电点pH值接近 4 5 .这种聚两性电解质性质在对铼Re(Ⅶ )离子浓集中也有所表现     

Synthesis of associating poly(acrylic acid) in supercritical carbon dioxide and its solution properties

Hydrophobically associating polymers have been synthesized in supercritical carbon dioxide by copolymerization of acrylic acid with different amounts of acrylate with hydrocarbon or fluorocarbon groups. It was found that conversion of hydrocarbon comonomers was above 95% whereas that for fluorocarbon comonomers was only about 50%. In addition, large amounts of hydrophobic groups could be easily introduced to poly(acrylic acid) by reaction in supercritical carbon dioxide. The solution properties were investigated by rheology. The results indicated that intermolecular association of the copolymer was strong and viscosity was maximum under acidic conditions. In aqueous solutions fluorocarbon hydrophobes associated much more strongly than the hydrocarbon variety, but the viscosifying effect of PAAC-18 series copolymers in 2% (w/w) solution was more pronounced than that of the PAAF series, results which did not agree with the conclusions of Ravey and Stébé. It was also found that the thixotropy behavior of copolymer solution at pH 3.2 was more complex than that at pH 5.0, at which pseudoplasticity only was observed for solutions of all copolymers. Contact angles of copolymer solutions on a glass sheet were measured. The data indicated that contact angles of hydrocarbon-modified polymers were smaller than those of fluorocarbon analogues. As time passed the contact angle became smaller and smaller. Fluorocarbon analogues were better than hydrocarbon analogues, and longer hydrophobic chains were better than shorter chains, at maintaining the hydrophobic character of the surface.     

聚丙烯酸接枝辛基酚聚氧乙烯醚的合成、表征和胶束化

通过自由基聚合, 丙烯酸(AA)与辛基酚聚氧乙烯醚丙烯酸酯活性大单体(C8PhEO10Ac)共聚,合成了以聚丙烯酸为主链、C8PhEO10Ac 为支链的水溶性两亲接枝共聚物(PAA-g-C8PhEO10Ac), 用凝胶渗透色谱(GPC)测定其相对数均分子质量为4.37×10⁴, 用FTIR和1H-NMR表征了共聚物的结构和组成, 共聚物分子中丙烯酸单体与活性大单体的摩尔比为9:1, 每个共聚物分子中平均约有32个C8PhEO10侧链. 用表面张力法、荧光探针法和透射电子显微镜对共聚物在水溶液中的自组装行为进行了初步研究, 结果表明, 共聚物分子在第一临界胶束浓度cmc1)和第二临界胶束浓度(cmc2)时都形成了球型胶束. 与cmc1时相比, cmc2时溶液表面张力进一步降低, 胶束内部极性进一步减小, 而且胶束粒径增大、结构紧密. 氯化钠的加入可使共聚物溶液的表面张力和胶束内部极性降低.     

Studies on Synthesis and Characterization of Charge Transfer Polymerization of Styrene and Alkyl Methacrylates

Abstract

Copolymers involving styrene and homologues of alkyl methacrylates (viz., methyl, ethyl, and butyl methacrylates) were synthesized at 60°C by employing a mixture of n‐butylamine and carbontetrachloride as charge transfer (CT) initiators in dimethyl sulphoxide medium. The CT complex was characterized by UV spectroscopy while the respective copolymers were characterized by employing infrared (IR) and ¹H NMR spectroscopy. The copolymer compositions were determined by using ¹H NMR spectroscopy and the reactivity ratios were computed by Fineman–Ross (F–R) and Kelen–Tudos (K–T) methods. The reactivity ratios of Sty‐MMA and Sty‐EMA copolymers indicate that higher level of styrene is incorporated in the copolymer. On the other hand the Sty‐BMA system exhibits different behavior. The higher value of r ₂ is obtained denoting that BMA is more active than styrene and hence, more BMA is present in the copolymer chain. In Sty‐MMA and Sty‐BMA systems, the product of r ₁ and r ₂ is greater than 1, representing the formation of high degree of random copolymers. However, in the case of Sty‐EMA, the product of r ₁ and r ₂ is less than 1 indicating the formation of alternating copolymer.     

Synthesis and monomer reactivity ratios of (vinylcyclohexane-co-N-vinyl-2-pyrrolidone) copolymer

A copolymer containing vinylcyclohexane (VCH) and N-vinyl-2-pyrrolidone (VP) at different compositions was synthesized and characterized. The monomer reactivity ratios (MRR) were estimated by using the classical Fineman-Ross and Kelen-Tüdõs linear fitting methods. These parameters were also estimated using a nonlinear computational fitting procedure, known as reactivity ratios error in variable model (RREVM). In this case, the values of MRR are r_VP=2.2 and r_VCH=0.0. Composition shifts and MRR values for (vinylcyclohexane-co-N-vinyl-2-pyrrolidone) copolymer (VCH-co-VP) are interpreted in terms of the relative comonomeric structures. A copolymer with zones containing VP blocks with isolated units of VCH between them is obtained. The presence or absence of the resonance stabilization effect is taken into account. The results are compared with those of similar related copolymeric systems.     

Reaction of the acrylic acid and 1-vinylimidazole copolymer with CuCl2 in aqueous solution

The reaction of acrylic acid—1-vinylimidazole copolymer with CuCl₂ in an aqueous medium was investigated by potentiometric titration and UV and ESR spectroscopy. The complex formation involves both the azole units and the carboxy groups. The Cl^– ions are also incorporated in the inner sphere of the complexes, their removal by dialysis resulting in an increase in the coordination capacity of the carboxylate groups.     

Synthesis of (meth)acrylate Block Copolymers by Ligated Anionic Polymerization

Synthetic potential of the ligated anionic polymerization (LAP) of acrylic and metacrylic esters initiated with methyl 2-lithioisobutyrate (MIB-Li) in the presence of an excess of alkali metal tert-alkoxides (prevailingly Li tert-butoxide) is presented. tert-Alkoxides form with ester-enolates, like MIB-Li, cross-aggregates of various composition, which tailor the environment of growing chain-ends, lower their nucleophilicity and restrict in this way the extent of side reactions, in particular self-termination of growing macroanions by back-biting reaction. Thus, stability of polymethacrylate living chains is sufficiently high for methacrylate and acrylate block copolymers to be synthesized. In the case of acrylate polymerization, reaction conditions must be optimized due to their high tendency to self-termination.     

Effect of the acrylic acid content on the permeability and water uptake of poly(styrene-co-butyl acrylate) latex films

In this contribution, a theoretical modeling of the latex film formation is presented and compared to experimental results: water vapor permeability and latex film capacitance are studied as a function of acrylic acid content in poly(styrene-co-butyl acrylate) latex films. It has been shown that both water uptake and water vapor permeability are mainly affected by film morphology which in turn is defined by intercolloidal interaction and drying rate.     

Synthesis and Characterization of Chitosan-grafl-Poly（lactic acid） Copolymer

Chitosan-graft-poly(lactic acid)(CS-g-PLA) copolymer was synthesized through emulsion self-assembly in a water-in-oil(W/O) microemulsion. The water phase was composed of CS aqueous solution, while the oil phase was made up of PLA in chloroform. The W/O microemulsion was fabricated in the presence of surfactant span-80 and the self-assembly was performed between PLA and CS under the effect of N-(3-dimethylaminopropyl)-N′-ethylcarbodiimide hydrochloride(EDC·HCl). FTIR and1H-NMR analysis indicated PLA was grafted onto the backbone of CS via the reaction between the carboxyl groups in PLA and the amino groups in CS.1H-NMR characterization further revealed the grafting content of PLA was 16%. The obtained CS-g-PLA could self-assemble to form micelles, their size distributed in the range of 125 375 nm with average diameter of 142 nm. The present design integrates the favorable biological properties of CS and the excellent mechanical properties of PLA, which makes CS-g-PLA copolymer a promising candidate as a carrier for targeted bioactive molecules delivery.     

（甲基）丙烯酸多环脂基酯单体及其聚合物

介绍部分(甲基)丙烯酸多环脂基酯及其聚合物的合成、性质与用途。     

Electrochemical properties of PP membranes with plasma polymer coatings of acrylic acid

Commercial polypropylene (PP) membranes were modified by plasma polymerization coating of acrylic acid, in combination with oxygen flow or oxygen plasma etching. First, conditions for plasma polymerization coating were optimized in terms of the chemical resistance of the coatings and their ion exchange capacity as a function of plasma power, internal pressure and treatment time. Next, the plasma polymerization coating of acrylic acid was combined with oxygen flow or oxygen plasma etching, and their conditions were also optimized by measuring the ion exchange capacity. Finally, the modified membranes were subjected to electrical resistance and transport number measurements and characterized by -step, FT-IR/ATR and SEM. Among the modification methods, oxygen plasma etching followed by the plasma polymerization coating of acrylic acid provided the best electrochemical properties with 1.75 meq/g (IEC) and 112 Ω cm² (ER), 0.88 (TN).     

Radiation synthesis of superabsorbent poly(acrylic acid)–carrageenan hydrogels

A series of superabsorbent hydrogels were prepared from carrageenan and partially neutralized acrylic acid by gamma irradiation at room temperature. The gel fraction, swelling kinetics and the equilibrium degree of swelling (EDS) of the hydrogels were studied. It was found that the incorporation of even 1% carrageenan (sodium salt) increases the EDS of the hydrogels from 320 to 800 g/g. Thermal analysis were carried out to determine the amount of free water and bound water in the hydrogels. Under optimum conditions, poly(acrylic acid)–carrageenan hydrogels with high gel fraction (80%) and very high EDS (800 g/g) were prepared gamma radiolytically from aqueous solution containing 15% partially neutralized acrylic acid and 1–5% carrageenan. The hydrogels were also found to be sensitive to the pH and the ionic strength of the medium.     

Synthesis and photophysical properties of colloids fabricated by the layer-by-layer polyelectrolyte assembly onto Eu(III) complex as a core

The luminescent colloids have been synthesized through the layer-by-layer assembly of poly(sodium 4-styrenesulfonate) (PSS) and polyethyleneimine (PEI) onto the luminescent core. The latter has been obtained by the reprecipitation of complex Eu[(TTA)(3)1] (where TTA(-) and 1 are thenoyltrifluoroacetonate and 2-(5-chlorophenyl-2-hydroxy)-2-phenylethenyl-bis-(2-methoxyphenyl)phosphine oxide, respectively) from organic solvent to aqueous solution. The variation of Eu(III) complexes indicates the role of the complex core in the development of such core-shell colloids. Complex Eu[(TTA)(3)1] is most convenient precursor of Eu-doped luminescent nanocomposites. The fluorometric measurements at each step of the layer-by-layer polyelectrolyte assembly onto Eu[(TTA)(3)1] core, at various pHs and additives reveal the quenching of Eu-centered luminescence as a result of the interfacial interaction of the core and the dye. The AFM images and electrochemical behavior of PSS-(PEI-PSS)(n)-Eu[(TTA)(3)1] colloids deposited on the surface indicate the stability of the polyelectrolyte multilayer in the dried state.     

Synthesis and characterization of poly(vinylpyrrolidone-co-vinylphosphonic acid) copolymers

Radical copolymerizations of 1-vinyl-2-pyrrolidone (VP) with vinylphosphonic acid (VPA) at different feed ratios were investigated. The copolymers were characterized by ¹H-NMR, ¹³C-NMR and FT-IR. The copolymer composition was determined from the elemental analysis. Thermogravimetric analysis (TG) illustrates that the copolymers are stable up to 200 °C. Temperature dependence of the alternating current (AC) conductivities were investigated by means of impedance spectroscopy. The direct current (DC) conductivities of the samples are derived from the AC conductivity data.     

Polymer colloids formed by polyelectrolyte complexation of vinyl polymers and polysaccharides in aqueous solution

The polyelectrolyte complex formed from the polyanion and polycation was studied by turbidimetry, static and electrophoretic light scattering, and elementary analysis. Sodium salts of polyacrylate (PA) and heparin (Hep) were chosen as the polyanion, and hydrochloric salts of poly(vinyl amine) (PVA) and chitosan (Chts) as the polycation. Although these vinyl polymers and polysaccharides have remarkably different backbone chemical structures and linear charge densities, all the four combinations PA-PVA, PA-Chts, Hep-PVA, and Hep-Chts provide almost stoichiometric polyelectrolyte complexes which are slightly charged owing to the adsorption of the excess polyelectrolyte component onto the neutral complex. The charges stabilize the complex colloids in aqueous solution of a non-stoichiometric mixture, and the aggregation number of the complex colloids increases with approaching to the stoichiometric mixing ratio. The mixing ratio dependence of the aggregation number for the four complexes is explained by the model proposed in the previous study.     

N-对甲苯基甲基丙烯酰胺的合成及与甲基丙烯酸甲酯共聚合的研究

本文合成了N-对甲苯基甲基丙烯酰胺(N-p-TMA),用IR和NMR进行了表征。制得了N-p-TMA与甲基丙烯酸甲酯(MMA)的共聚体,给出了共聚体的IR和NMR谱。用核磁共振测得N-p-TMA-与-MMA共聚合的竞聚率γ_N-p-TMA=0.78±0.02,γ_MMA=1.43±0.02。用热机械曲线测出了共聚体的T_g和T_f,并发现T_g和T_f值随着共聚体中酰胺含量的增加而升高。     

磁性壳聚糖-聚丙烯酸微球的制备及表征

壳聚糖通过与丙烯酸接枝共聚制得壳聚糖聚丙烯酸悬浮液,在铁磁流体(Fe3O4)与聚乙二醇(分散剂)存在下通过与戊二醛交联,制备了磁性壳聚糖聚丙烯酸微球。用扫描电镜、红外光谱对合成的高分子微球进行形貌观察和结构表征,并进行了元素分析和磁性能测试,研究了磁性微球对牛血清白蛋白(BSA)的吸附效果。结果表明,合成的磁性微球外表呈球形,粒径为100～400nm;当Fe含量为2.47%时,磁性微球的饱和磁化强度约为1.30emug,磁矫顽力为280Oe,磁化率为2.16×10-4(常温下),属于顺磁性材料;其对BSA有较好的吸附效果,饱和吸附量约为400mgg。     

Synthesis, surface and aggregation properties of a series of amphiphilic dendritic copolymers

With 3.0 G polyamidoamine (PAMAM) as initiator and poly (propylene oxide) (PPO)–poly (ethylene oxide) (PEO) blocks as branches, a new class of amphiphilic copolymers were synthesized. The critical micelle concentration (CMC) and γ_CMC (surface tension at CMC) values were determined by surface tension measurement, and the result showed that they both decrease with the increase of amphiphilic branch length. The turbidity properties were investigated and it was found that the cloud point (CP) temperature decreases as the PEO block length increases. Freeze-fracture transmission electron microscopy (FF-TEM) results exhibited spherical shape of aggregates with the most probable distribution size of around 100 nm, which agrees with the results of the dynamic light scattering (DLS). Moreover, the relationship between PPO block length and the activity and CP properties was discussed.     

共轭/非共轭嵌段聚苯撑乙烯(PPV)类共聚物的合成与性能

用活性中间体直接引发共轭/非共轭单体聚合的新方法合成了3种PPV嵌段共聚物;用核磁共振谱和FTIR光谱确定了共聚物的结构.引入非共轭片段PS缩短了PPV共轭链的长度,改善了聚合物的溶解性和可加工性.荧光光谱结果表明,嵌段聚合物可使发射峰蓝移,发光的量子效率明显提高,进而调节了发光颜色.