Synthesis and characterization of poly[2,5-bis(triethoxy)-1,4-phenylene vinylene]

The synthesis of a highly soluble, 2,5-disubstituted poly(p-phenylene vinylene) with pendant side chains containing ether groups was accomplished by a dehydrochlorination route. Specific interactions of the oxygen-containing side chains with the solvent are presumably responsible for the high solubility of the polymer, especially in protogenic solvents. The polymer microstructure was characterized by ¹H- and ¹³C-NMR. The polymer showed solvatochromic properties when dissolved in a variety of solvents. The relatively high molecular weight (M_n = 17,000) permitted the fabrication of free-standing films. The electrical conductivity of iodine-doped films was approximately 2 × 10^–2 S cm^–1. © 1995 John Wiley & Sons, Inc.     

Synthesis and properties of polyimides derived from 1,4-bis(4-aminophenoxy)2,5-di-tert-butylbenzene

Novel aromatic polyimides containing symmetric, bulky di-tert-butyl substituents unit were synthesized from 1,4-bis(4-aminophenoxy)2,5-di-tert-butylbenzene (BADTB) and various aromatic tetracarboxylic dianhydrides by the conventional two-stage procedure that included ring-opening polyaddition in a polar solvent such as N,N-dimethylacetamide to give poly(amic acid)s, followed by cyclodehydration to polyimides. The diamine was prepared through the nucleophilic displacement of 2,5-di-tert-butylhydroquinone with p-chloronitrobenzene in the presence of K₂CO₃, followed by catalytic reduction. Depending on the dianhydrides used, the poly(amic acid)s obtained had inherent viscosities of 0.83–1.88 dL g⁻¹. Most of the polyimides formed transparent, flexible, and tough films. Tensile strength and elongation at break of the BADTB-based polyimide films ranged from 68–93 MPa and 7–11%, respectively. The polyimide derived from 4,4′-hexafluoro-isopropylidenebisphathalic anhydride had better solubility than the other polyimides. These polyimides had glass transition temperatures between 242–298°C and 10% mass loss temperatures were recorded in the range of 481–520°C in nitrogen. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1527–1534, 1997     

A novel orange phosphor of Eu-activated calcium chlorosilicate for white light-emitting diodes

Novel orange phosphor of Eu²⁺-activated calcium chlorosilicate was synthesized at 1273 K by conventional solid-state reactions under reductive atmosphere and investigated by means of photoluminescence excitation, diffuse reflectance and emission spectroscopies. These results show that this phosphor can be efficiently excited by the incident light of 300-450 nm, well matched with the emission band of 395 nm-emitting InGaN chip, and emits an intense orange light peaking at 585 nm. By combining this phosphor with a 395 nm-emitting InGaN chip, an intense orange light-emitting diode (LED) was fabricated. Under 20 mA forward-bias current, its CIE chromaticity coordinates are (0.486, 0.446). The dependence of as-fabricated orange LED on forward-bias current indicates that it shows excellent chromaticity stability and luminance saturation. These results show that this Eu²⁺-activated calcium chlorosilicate is a promising orange-emitting phosphor for near-ultraviolet (UV) InGaN-based white LED.     

Synthesis and Fluorescence of alt-Copoly[1, 4-divinylenebenzene／1, 4-bis（dimethylsilylene）benzene]

Silicon inserted n conjugated copolymer was synthesized by Heck reaction with moderate molecular weight. This silicon containing copolymer is thermally stable to 400℃, while emission of this polymer is blue-shifted compared with polyphenylenevinylene greenish emission. It shows potential application as organic emitter in OLED.     

Synthesis characterization and X-ray crystal structures of cis-1,4-diaminocyclohexane-platinum(II) nucleobase adducts

Platinum complexes of the type [Pt(cis-1,4-DACH)(L)₂]X, where cis-1,4-DACH = cis-1,4-diaminocyclohexane; L = adenine (ade) (1), hypoxanthine (hyp) (2), 9-methylguanine (9-megua) (3), cytosine (cyt) (4), or 1-methylcytosine (1-mecyt) (5); and X = SO₄ or Cl₂ groups, were synthesized and characterized by elemental analysis and by ¹H, ¹³C, and ¹⁹⁵Pt nuclear magnetic resonance spectroscopy. The crystals of [Pt(cis-1,4-DACH)(9-megua)₂]SO₄[9-megua-H]₂SO₄ (3) and [Pt(cis-1,4-DACH)(1-mecyt)₂]Cl₂ · 6H₂O (5) were also subjected to single-crystal X-ray diffraction. The base/PtN4 coordination plane dihedral angles were 74.55° and 85.61° in complex 3 and 78.12° and 81.80° in complex 5. The platinum had distorted square planar geometry in both complexes; the two adjacent corners were occupied by the two nitrogen atoms of cis-1,4-DACH, and the other two corners were occupied by the two N7 atoms of 9-megua in complex 3 and the two N3 atoms of 1-mecyt in complex 5. The cis-1,4-DACH, which has a unique twist-boat configuration, formed a seven-member chelating ring with platinum, which led to considerable strain during bidentate cis-1,4-DACH binding. Cations of both complexes 3 and 5 adopted C₂ molecular symmetry. These adducts were the models for the intrastand cross-links that were relevant to the binding of the Pt(II) antitumor drugs to DNA.     

Synthesis and characterization of fluorene and carbazole dithienosilole derivatives for potential applications in organic light-emitting diodes

Several fluorene or carbazole-based dithienosiloles (DTSs) have been synthesized and their thermal, photophysical, and electrochemical properties have been systematically investigated. These compounds show high thermal stability with glass transition temperature above 110 °C as well as decomposition temperatures at ∼400 °C. Intense green emission is observed in the spectral region of 500-510 nm for all compounds (Φ_PL=0.31-0.80), that is, attributed to both the 5,5′-substituents of the DTS ring and DTS-based π-π^∗ transition. Based on the emission spectra at 77 K, the triplet energy for these compounds was calculated to be within 2.1-2.2 eV, indicating that they may be used as host materials for red emitters in organic light-emitting diodes (OLEDs). All compounds exhibit reversible oxidation and possess low-lying LUMO energies, owing to the conjugated fluorene/carbazole substituents on the DTS. This along with the high thermal/electrochemical stabilities and high fluorescent quantum efficiencies makes the new DTSs compounds promising candidates for use in OLEDs as emitters, host and electron-transporting materials.     

New family of highly emissive,soluble poly(1,4‐fluorenylenevinylene) derivatives: Synthesis and characterization

A new poly(arylene vinylene) derivative, poly(1,4‐fluorenylenevinylene), with the advantages of poly(p‐phenylene vinylene) and polyfluorene (PF), was designed, synthesized, and characterized. The polymer showed a defect‐free structure and a number‐average molecular weight of 32,600. The resulting polymer was thermally stable with a high glass‐transition temperature (200 °C) and was readily soluble in common organic solvents. The polymer film showed a maximum emission at 515 nm and had a photoluminescence quantum yield of 58 ± 5%. A cyclic voltammetry study revealed that the highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels of the polymer were 2.9 and 5.51 eV, respectively. The double‐layer light‐emitting‐diode devices fabricated from the polymer emitted bright green light with a maximum around 515 nm. The device showed a maximum luminous efficiency of 0.13 cd/A and a maximum luminance value of 600 cd/m² at 17 V. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6515–6523, 2005     

Synthesis of 2,5 -Bis(4-methyl-2-thienyl)thiophene and 2,5-Bis(4-methyl-2-thienyl)pyrrole

Syntheses of 2,5-bis(4-methyl-2-thienyl)thiophene 3 and 2,5-bis(4-methyl-2-thienyl)pyrrole 4 are described. The key step involves Stetter reaction between 4-methyl-2-thiophenecarboxaldehyde and divinyl sulfone. Cyclizaton of the resulting 1,4-bis-(4-methyl-2-thienyl)-1,4-butanedione 2 with Lawesson's reagent gives 2,5-bis(4-methyl-2-thienyl)thiophene 3, whereas condensation with ammonium acetate provides the 2,5-bis(4-methyl-2-thienyl)pyrrole 4.     

Synthesis of 2,5-bis(2-aminothiazol-5-yl)-3,6-dichloro-1,4-benzoquinones

A series of 2-(2-aminothiazol-5-yl)-3,6-dichloro-5-diethylaminoethenyl-1,4-benzoquinones was synthesized from 2-(2-aminothiazol-5-yl)-3,5,6-trichloro-1,4-benzoquinones using acetaldehyde and diethylamine in toluene solution. Refluxing these compounds with substituted thioureas in acetonitrile in the presence of hydrochloric acid gives the corresponding 2,5-bis(2-aminothiazol-5-yl)-3,6-dichlorohydroquinones which can be oxidized to the target products with ferric chloride in aqueous DMF.Riga Technical University, Riga LV-1048, LatviaTranslated from Khimiya Geterotsiklicheskikh Soedinenii, No. 6, pp. 835–839, June, 2000     

Synthesis and properties of new polyamides derived from 1,4-bis(4-aminophenoxy)-2,5-di-tert-butylbenzene and aromatic dicarboxylic acids

The diamine 1,4-bis(4-aminophenoxy)-2,5-di-tert-butylbenzene, containing symmetric, bulky di-tert-butyl substituents and a flexible ether unit, was synthesized and used to prepare a series of polyamides by the direct polycondensation with various aromatic dicarboxylic acids in N-methyl-2-pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. All the polymers were obtained in quantitative yields with inherent viscosities of 0.32–1.27 dL g⁻¹. Most of these polyamides, except II _a , II _d , and II _e , showed an amorphous nature and dissolved in polar solvents and less polar solvents. Polyamides derived from 4,4′-sulfonyldibenzoic acid, 4,4′-(hexafluoro-isopropylidene)dibenzoic acid, and 5-nitroisophthalic acid were even soluble in a common organic solvent such as THF. Most polyamide films could be obtained by casting from their N,N-dimethylacetamide (DMAc) solutions. The polyamide films had a tensile strength range of 49–78 MPa, an elongation range at break of 3–5%, and a tensile modulus range of 1.57–2.01 GPa. These polyamides had glass transition temperatures ranging between 253 and 276°C, and 10% mass loss temperatures were recorded in the range 402–466°C in nitrogen atmosphere. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1069–1074, 1998     

Synthesis and electrical conductivity of poly(1,4-phenylenevinylene-co-2-nitro-1,4-phenylenevinylene)

A series of PPV copolymers containing 2-nitro-1,4-phenylenevinylene (NO₂-PV) units were prepared via the water-soluble precursor route. They were obtained in film form and were doped with I₂ and FeCl₃. Doping increased the electrical conductivities to maximum values of about 3×10^?2 and 3×10^?1 s cm^?1, respectively, for the two dopants. Conductivity depended strongly on the composition of the copolymers; it reached a maximum value at ca. 1–2 mol % of NO₂-PV units in the copolymers and then dropped rapidly with further increase in NO₂-PV content. Electronic effects of the substituent and morphological changes induced by copolymerization appear to interplay intricately, resulting in the occurrence of a maximum conducting composition. © 1993 John Wiley & Sons, Inc.     

2,5-Dimethoxy-2,5-dihydrofuran chemistry: a new approach to 2(5H)-furanone derivatives

2,5-Dimethoxy-2,5-dihydrofuran is a synthetic equivalent of 2(5H)-furanone or 2-trimethylsilyloxyfuran, useful C₄ synthons in the preparation of 5-substituted-2(5H)-furanone derivatives. The reaction conditions adopted allow to obtain different classes of complex and biologically interesting compounds, in only one step, with high yields.     

Synthesis and characterization of spin-coatable tert-amine molecules for hole-transport in organic light-emitting diodes

The synthesis of two tert-amine-based, non-fluorescent, hole-transport molecules (4,4′-[bis-{(4-di-n-hexylamino)benzylideneamino)]stilbene (DHABS) and 4,4′-[bis-{(4-diphenylamino)benzylideneamino}]stilbene) (DPABS) that are suitable for spin coating on indium tin oxide (ITO) for electronic device fabrication is described and compared with the widely used TPD. Electroluminescence occurred at a turn-on voltage of 7-8 V in ITO/hole-transport layer (HTL, spin coated)/Alq₃/Al devices.     

Synthesis and characterization of new hexahelicene derivatives

The synthesis and structural characterization of a new hexahelicene derivative 2 is reported. This compound features a new type of structure bearing a bromine atom and a methoxy group. Suitable crystals of the latter indicate that its conformation closely resembles that of the unsubstituted [6]helicene, whose idealized symmetry is C2. This 3-bromo-14-methoxyhexahelicene was subjected to lithiation/phosphinilation and yielded the new 3-methoxy-14-(diphenylphosphino)hexahelicene 3.     

Synthesis of 2,5-diethynyl substituted oxepins from trans-1,4-diethynylcyclohexa-2,5-diene-1,4-diols

Reaction of trans-1,4-bis(trimethylsilylethynyl)cyclohexa-2,5-diene-1,4-diol with n-BuLi followed by methanesulfonyl chloride resulted in the formation of a dark red solid, which was identified as 2,5-bis(trimethylsilylethynyl)oxepin. Deprotection of the silyl groups resulted in the formation of 2,5-diethynyloxepin, a red, shock sensitive solid. Reaction of a differentially substituted cyclohexa-2,5-diene-1,4-diol gave a mixture of 2,5-diethynyl substituted oxepins.     

Synthesis, characterization, physical properties, and applications of highly fluorescent pyrene-functionalized 9,9-bis(4-diarylaminophenyl)fluorene in organic light-emitting diodes

A new, highly fluorescent pyrene-functionalized 9,9-bis(4-diarylaminophenyl)fluorene, namely PTF, was synthesized and characterized. This material is an amorphous molecular glass with notably high T_g, is electrochemically stable, and exhibits strong blue emission both in solution and solid state. It shows promising ability as a solution processed blue emitter and hole-transporter for OLEDs. High-efficiency sky-blue and Alq3-based green devices with luminance efficiencies of 1.13 and 4.08 cd/A are achieved, respectively.     

Synthesis and characterization of poly(d,l-lactide-co-glycolide) modified by maleic anhydride and 1,4-butanediamine

Bone tissue engineering is sought to apply strategies for bone defects healing biodegradable porous scaffolds without limitations and shortcomings. In this work, we have developed a novel maleic anhydride (MAH) and 1,4-butanediamine modified poly(lactide-co-glycolide) polymer (BMPLGA). The synthesized polymer was characterized by Fourier transform infrared spectrometry (FTIR), Nuclear magnetic resonance spectra (¹H NMR), gel permeation chromatography (GPC) and contact angle measurements. In addition, cell morphologies in the extracts and cell cytotoxity were also studied. The results showed that the BMPLGA was successfully obtained by introducing MAH and 1,4-butanediamine into PLGA in bulk. The introduction of anhydride and amino groups improved the hydrophilicity of PLGA. Fibroblastic cells showed normal morphologies in BMPLGA extracts, and the BMPLGA materials showed no cell cytotoxicity. The synthetic BMPLGA material may have potentials for biomedical applications due to improving hydrophilicity.