有限势库化学机最大输出功时循环最优构型

基于有限势容高化学势库和无限势容低化学势库间工作的等温内可逆化学机,在循环总时间一定的条件下,应用最优控制理论导出了一类普适传质规律下对应于最大输出功时化学机循环最优构型.特例分析表明传质定律为g∝△μ(△μ为化学势差)时循环最优构型为低化学势侧工质中关键组分的化学势(或浓度)为常数,而工质与有限势容高化学势库间关键组分的化学势(或浓度)均随时间呈非线性变化且化学势之差(浓度之比)为常数的等温内可逆化学机循环;传质定律为g∝△c(△c为浓度差)时循环最优构型与传质定律g∝△μ下循环最优构型存在显著不同;当高化学势库也为无限势容化学势库时,循环最优构型由两个等化学势传质分支和两个等质量流率分支组成,且与具体的传质定律无关.本文的研究对象具有一定的普适性,研究结果对于实际化学机的优化设计与最优运行具有一定参考价值.     

不同生物炭材料的制备及其在Li-S电池中的应用

Biochar derived from reproducible massive biomasses presents the advantages of low cost and renewable resources. In this work aiming to solve the existing problems of the lithium-sulfur battery, sulfur@biochar (S@biochar) composite cathode materials with high capacity and good cycle performance were developed. Specifically, four kinds of biochar prepared from rice husk, miscanthus, fir, and pomelo peel were used as host matrices for the Li-S battery. Among them, the S@biochar derived from rice husk delivered the highest specific capacity and the best cycle stability according to electrochemical tests. To further optimize its performance, we prepared a highly porous rice husk derived biochar (HPRH-biochar) using silica gel as the template. The S@HPRH-biochar composite (60% (w, mass fraction) S) enables the homogeneous dispersion of amorphous sulfur in the carbon matrix and its porous structure could effectively suppress the dissolution of the polysulfide. As a result, its electrochemical performance improved, achieving a high initial charge capacity of 1534.1 mAh·g^-1 and maintaining a high capacity of 738.7 mAh·g^-1 after 100 cycles at 0.2C (1C corresponds to a current density of 1675 mA·g^-1). It also gives a capacity of 485.3 mAh·g^-1 at 2.0C in the rate capacity test.     

稻壳基活性炭对锰酸锂电池倍率性能的影响

稻壳基活性炭(RH-AC)具有天然的多级孔道结构,是由稻壳碳化和活化两步得到的。 用RH-AC和锰酸锂(LMO)混合制备复合电极,以锂片为对电极,组装半电池进行恒流充放电测试。 实验发现:含有质量分数为5%的RH-AC与90.5%的LMO的复合电极(RH-AC5)在5C电流密度循环100圈后比容量为89.3 mA·h/g,容量保持率高于89%,远优于纯锰酸锂电极。 采用循环伏安法计算出的锂离子扩散系数,及利用交流阻抗测试拟合后得到的结果进一步验证了该结论。     

Computational evaluation of mass filter acceptance and transmittance influenced by developing fields: An application of the plane method to investigate prefilter efficacy for rectangular wave operated mass filters

The acceptance of quadrupole mass filters is improved when the alternating current (AC) and direct current (DC) fields are developed separately. Physically, this is achieved when a short RF only quadrupole (prefilter) is situated directly ahead of the mass filter. The acceptance gained by a system operating with a prefilter can be observed as an increase in sensitivity over conventional operation. Frequency dynamic duty cycle based rectangular waveform driven (rectangular wave) mass filters, a recent development, currently do not operate with prefilters. Little is known about the influence of duty cycle changes on the acceptance of rectangular wave mass filters. The sensitivity gain seen by conventional systems operating with prefilters indicates that the sensitivity of duty cycle based rectangular wave systems should increase comparably. The objective of this work was to determine prefilter efficacy for nonspecific rectangular wave mass filter systems. In this work, the plane method of acceptance was used to model the change to the acceptance and transmittance of sine and rectangular waveform driven mass filters under different modes of field development. Both systems indicated a fourfold increase in sensitivity when the mass filtering DC or duty cycle was delayed.     

Ultrasonic/microwave assisted extraction and diagnostic ion filtering strategy by liquid chromatography-quadrupole time-of-flight mass spectrometry for rapid characterization of flavonoids in Spatholobus suberectus

Spatholobus suberectus is a widely used herb in traditional medicine for the treatment of blood stasis syndrome and related diseases. In this work, a potential ultrasonic/microwave assisted extraction (UMAE) method was developed for efficient sample pretreatment, and a diagnostic ion filtering strategy with liquid chromatography-quadrupole time-of-flight mass spectrometry (LC-Q-TOF-MS) was established for rapid characterization of flavonoids in S. suberectus. The factors of UMAE influencing the extraction yield of flavonoids of S. suberectus were evaluated. The optimal conditions were determined as: microwave power of 300 W, extraction time of 450 s, 70% methanol as extraction solvent, solvent to solid ratio of 20 mL/g, ultrasound power of 50 W, extraction temperature of 80 °C, and one extraction cycle. Compared with commonly used extraction methods, UMAE showed higher efficiency and shorter extraction time for sample preparation. Subsequently, the major diagnostic ions and fragmentation pathways of flavonoids in Q-TOF-MS were summarized with available reference compounds. Using a new diagnostic ion filtering strategy, a rapid screening and identification of thirty-eight compounds was achieved in real S. suberectus samples. The results of this study clearly demonstrate the potential of UMAE for efficient extraction and LC-Q-TOF-MS for rapid and sensitive structural elucidation of flavonoids in S. suberectus, and open perspectives for similar studies on other medicinal herbs.     

Optimal performance of a generalized irreversible four-reservoir isothermal chemical potential transformer

A new cyclic model of a four-reservoir isothermal chemical potential transformer with irreversible mass transfer, mass leakage and internal dissipation is put forward in this paper. The optimal relation be-tween the coefficient of performance (COP) and the rate of energy pumping of the generalized irre-versible four-reservoir isothermal chemical potential transformer has been derived by using finite-time thermodynamics or thermodynamic optimization. The maximum COP and the corresponding rate of energy pumping, as well as the maximum rate of energy pumping and the corresponding COP, have been obtained. Moreover, the influences of the irreversibility on the optimal performance of the iso-thermal chemical potential transformer have been revealed. It was found that the mass leakage affects the optimal performance both qualitatively and quantitatively, while the internal dissipation affects the optimal performance quantitatively. The results obtained herein can provide some new theoretical guidelines for the optimal design and development of a class of isothermal chemical potential trans-formers, such as mass exchangers, electrochemical, photochemical and solid state devices, fuel pumps, etc.     

Adsorptive separation by thermal parametric pumping part II: Experimental study of the purification of aqueous phenolic solutions at pilot scale

In this work scale-up concerns in adsorptive parametric pumping operation in recuperative mode are studied. An experimental study of the purification of wastewater containing 100 ppm of phenol using a polymeric adsorbent (Duolite ES861-Rohm and Haas, France) is reported. A completely automated pilot plant (column and ancillary equipment, product receivers, sampling, collector and analytical devices) is described. The plant is computer controlled enabling automatic data acquisition for temperature, pressure and flowrate. Parameters related with adsorption equilibrium, mass transfer and heat transfer resistances were determined in order to obtain basic information to simulate the process behavior. Continuous and semicontinuous top feed parametric pumping experiments were carried out in a bed with 0.09 m diameter and 1 m long which represents a scale-up by a factor of 60 relative to previous works. Optimal operating conditions yielding the maximum productivity of the bottom product (phenol concentration <1 ppm), were achieved experimentally with the following conditions: average cycle time =4 h, ratioφ _B /φ _T =2 (φ _B =0.27), reservoir volumeQ(π/ω)=32.5l, average flowrate=0.24l/min. Based on these conditions, after 12 cycles of operation, 105l of treated water is obtained. Those optimal operating conditions were suggested by simulation studies presented in Part I (Ferreira and Rodrigues, 1995) of this work. Good agreement was obtained between experimental and simulated results using the complete model developed in Part I (Ferreira and Rodrigues, 1995).     

热压法构筑锂负极聚偏氟乙烯基双功能保护层的研究

锂金属具有高比容量(3860 mA·h/g)和低电化学电位(-3.04 V vs. SHE), 是一种极具潜力的新型电池负极材料. 然而, 锂金属电化学稳定性差, 导致电池循环寿命受限, 容易产生枝晶, 造成电池短路, 引发安全风险, 而其对空气及环境的高度敏感性也极大增加了电池制作的难度与成本, 限制了其应用推广. 改善锂金属负极的界面稳定性被认为是提升锂金属电池性能的重要途径. 本文通过简单直接的热压法在锂金属负极表面构筑了聚偏氟乙烯(PVDF)基双功能保护层, 使锂金属的空气稳定性提升至约120 min, 并延长了锂金属对称电池的循环寿命至约1200 h; 再通过在PVDF保护层内引入亲锂的SnO₂粒子, 形成的无机有机复合保护层可以通过原位合金化反应提供锂沉积的形核位点, 在保持良好循环稳定性的基础上进一步降低成锂沉积的过电位, 极化过电位从0.016 V降低到0.007 V. 含有该保护层的全电池展现出约200次的长循环寿命与90%以上的高容量保持率, 在3C高倍率下放电比容量仍达127 mA·h/g. 提出的双功能电极界面保护层策略能有效提升锂金属负极空气稳定性和电化学性能.     

Redox-Bipolar Polyimide Two-Dimensional Covalent Organic Framework Cathodes for Durable Aluminium Batteries

Emerging rechargeable aluminium batteries (RABs) offer a sustainable option for next-generation energy storage technologies with low cost and exemplary safety. However, the development of RABs is restricted by the limited availability of high-performance cathode materials. Herein, we report two polyimide two-dimensional covalent organic frameworks (2D-COFs) cathodes with redox-bipolar capability in RAB. The optimal 2D-COF electrode achieves a high specific capacity of 132 mAh g⁻¹. Notably, the electrode presents long-term cycling stability (with a negligible ≈0.0007 % capacity decay per cycle), outperforming early reported organic RAB cathodes. 2D-COFs integrate n-type imide and p-type triazine active centres into the periodic porous polymer skeleton. With multiple characterizations, we elucidate the unique Faradaic reaction of the 2D-COF electrode, which involves AlCl²⁺ and AlCl₄⁻ dual-ions as charge carriers. This work paves the avenue toward novel organic cathodes in RABs.     

Effective adsorption of Hg(II) ions by new ethylene imine polymer/β-cyclodextrin crosslinked functionalized magnetic composite

A new effective magnetic composite material was prepared successfully for adsorption Hg(II) ions by introducing β-cyclodextrin/ethylene imine polymer to the mesoporous silica. The morphology and structure of EIP-β-CD magnetic adsorbents were characterized by FT-IR, XR, DTG, XPS and SEM technologies. The effect of many factors were discussed detailedly such as adsorption time, initial concentration, pH, different composition of adsorbent and adsorption temperature. It was found that EIP-β-CD showed excellent adsorption capacity, high selectivity, good reutilization and fast adsorption rate. The maximum adsorption capacity was 248.72 mg/g and the best removal rate was 99.49 % under the optimized experimental conditions. The kinetic and thermodynamic study showed typical characteristic of chemical adsorption, exothermic and spontaneous. The best mass proportion of β-cyclodextrin, ethylene imine polymer and glutaraldehyde was 1.0:0.4:0.2, and proper β-cyclodextrin can develop the adsorption capacity for Hg(II) ions in this adsorbent. The possible adsorption mechanism was investigated in detail. After the fifth cycle experiment, this new adsorbent still showed excellent adsorption capacity which indicated that it has great potential for Hg(II) ions cleanup in water solution.     

类石墨烯类活性炭材料的简易合成及其在锂硫电池中的应用研究

锂硫电池由于具有较高的理论容量被视为一种最具发展潜力的储能装置. 然而,硫的利用率较低及循环寿命短等问题限制着其商业化进程. 本文通过一种简单易行的方法将三聚氰胺（C₃H₆N₆）和L半胱氨酸(C₃H₇NO₂S)碳化,制备出一种氮掺杂类石墨烯活性炭材料（NGC）. 该材料的类石墨烯结构能够有效抑制锂硫电池在充放电过程中产生的体积效应,以此提升其循环性能. 不仅如此,材料中含有的含氮官能团还可以促进离子转移,抑制多硫化物的溶解,进而提升硫的利用率. 其中,制备出的NGC-8/PS复合电极用于锂硫电池时在0.2 C的电流密度下初始容量为1164.1 mAh·g^-1,在经过400圈的充放电循环之后依然具有909.4 mAh·g^-1的比容量,每圈容量衰减仅为0.05%,甚至在2C的电流密度下也能达到820 mAh·g^-1的高比容量.     

The design of an on-line semi-preparative LC-SPE-NMR system for trace analysis

This paper reports the design of an on-line semi-preparative LC-SPE-NMR system and its use in the structural analysis of mixture components at the 0.02-1% level. The combination provides at least a five fold mass sensitivity increase over that obtained from typical analytical LC-SPE systems and a >30-fold total NMR sensitivity enhancement over analysis by LC-NMR. This is accomplished by using a novel on-line device to store, dilute (1-100-fold) and deliver (at an optimized flow-rate) the isolated component of interest to an SPE trap unit. The SPE unit consists of two cartridges connected in parallel to increase the overall SPE capacity and also to decrease the flow-rate through each trap for enhanced trapping efficiency. As the coupling of semi-preparative LC with NMR (through SPE) is well matched in terms of optimal mass loading for both techniques, only one LC-SPE cycle is required to enrich a 50 microg ml(-1) component (1% in a 5 mg ml(-1) mixture) for the acquisition of heteronuclear (1)H-(13)C NMR data using a conventional NMR flow probe. Furthermore, analytes at the 0.02% level (approximately 1 microg ml(-1)) can be studied using 2D (1)H NMR techniques if peak cuts from replicate sample injections (> or =3) are accumulated into the storage/dilution unit and the resulting solution processed by just one SPE trap and elute cycle.     

Performance analysis and multi-objective optimization of an organic Rankine cycle with binary zeotropic working fluid employing modified artificial bee colony algorithm

From a thermal point of view, zeotropic mixtures are likely to be more efficient than azeotropic fluids in low-temperature power cycles for reduction in exergy destruction occurring during heat absorption/rejection processes due to their suitable boiling characteristics. In this study, comprehensive energetic and exergetic analyses are mathematically performed for an organic Rankine cycle (ORC) system employing a potential binary zeotropic working fluid, namely R717/water. For this purpose, initially mass, energy, and exergy balance equations are derived. With regard to the similarity in molar mass of R717 (17.03 g mol^?1) and water (18.01 g mol^?1), there is no need to alter the size of the ORC components such as turbine and pump. In order to achieve the optimal thermal and exergy efficiencies of the ORC system, modified version a powerful and relatively new optimization algorithm called artificial bee colony (ABC) is used taking into account different effective constraints. The main motivation behind using ABC lies on its robustness, reliability, and convergence rate speed in dealing with complicated constrained multi-objective problems. Convergence rates of the algorithm for optimal calculation of the efficiencies are presented. Subsequently, due to the importance of exergy concept in ORC systems, exergy destructions occurring in the components are computed. Finally, the impacts of pressure, temperature, mass fraction, and mass flow rate on the ORC thermal and exergy efficiencies are discussed.

     

A novel quantitative model of cell cycle progression based on cyclin-dependent kinases activity and population balances

Cell cycle regulates proliferative cell capacity under normal or pathologic conditions, and in general it governs all in vivo/in vitro cell growth and proliferation processes. Mathematical simulation by means of reliable and predictive models represents an important tool to interpret experiment results, to facilitate the definition of the optimal operating conditions for in vitro cultivation, or to predict the effect of a specific drug in normal/pathologic mammalian cells. Along these lines, a novel model of cell cycle progression is proposed in this work. Specifically, it is based on a population balance (PB) approach that allows one to quantitatively describe cell cycle progression through the different phases experienced by each cell of the entire population during its own life. The transition between two consecutive cell cycle phases is simulated by taking advantage of the biochemical kinetic model developed by Gérard and Goldbeter (2009) which involves cyclin-dependent kinases (CDKs) whose regulation is achieved through a variety of mechanisms that include association with cyclins and protein inhibitors, phosphorylation–dephosphorylation, and cyclin synthesis or degradation. This biochemical model properly describes the entire cell cycle of mammalian cells by maintaining a sufficient level of detail useful to identify check point for transition and to estimate phase duration required by PB. Specific examples are discussed to illustrate the ability of the proposed model to simulate the effect of drugs for in vitro trials of interest in oncology, regenerative medicine and tissue engineering.     

The role of material behavior in the performances of electroactive polymer energy harvesters

Electroactive polymer energy harvesters are promising devices for the conversion of mechanical work to electrical energy. The performances of these devices are strongly dependent on the mechanical response of the polymeric material and on the type of electromechanical cycle, and these are limited by the occurrence of dielectric breakdown, compression induced wrinkling and electromechanical instability (pull‐in). To identify the optimal electromechanical cycle that complies with all of these limitations, we set‐up and solve a constraint optimization problem and we critically discuss the influence of material behavior of the polymer in the optimal performances of the energy harvesting device. Finally, we show that if the rate‐independent dissipative behavior of the polymer (Mullins effect) is neglected, the optimization procedure may lead to quite unsatisfactory predictions: by making reference to explicit experimental data from literature we show that an optimal harvesting cycle deduced by neglecting the Mullins effect is far from being optimal when this is taken in consideration. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1303–1314     

A Four‐Electron Sulfur Electrode Hosting a Cu2+/Cu+ Redox Charge Carrier

The elemental sulfur electrode with Cu²⁺ as the charge carrier gives a four‐electron sulfur electrode reaction through the sequential conversion of S?CuS?Cu₂S. The Cu‐S redox‐ion electrode delivers a high specific capacity of 3044 mAh g^?1 based on the sulfur mass or 609 mAh g^?1 based on the mass of Cu₂S, the completely discharged product, and displays an unprecedently high potential of sulfur/metal sulfide reduction at 0.5 V vs. SHE. The Cu‐S electrode also exhibits an extremely low extent of polarization of 0.05 V and an outstanding cycle number of 1200 cycles retaining 72 % of the initial capacity at 12.5 A g^?1. The remarkable utility of this Cu‐S cathode is further demonstrated in a hybrid cell that employs an Zn metal anode and an anion‐exchange membrane as the separator, which yields an average cell discharge voltage of 1.15 V, the half‐cell specific energy of 547 Wh kg^?1 based on the mass of the Cu₂S/carbon composite cathode, and stable cycling over 110 cycles.     

Optimized expanded ensembles for simulations involving molecular insertions and deletions. II. Open systems

In the Grand Canonical, osmotic, and Gibbs ensembles, chemical potential equilibrium is attained via transfers of molecules between the system and either a reservoir or another subsystem. In this work, the expanded ensemble (EXE) methods described in part I [F. A. Escobedo and F. J. Martinez-Veracoechea, J. Chem. Phys. 127, 174103 (2007)] of this series are extended to these ensembles to overcome the difficulties associated with implementing such whole-molecule transfers. In EXE, such moves occur via a target molecule that undergoes transitions through a number of intermediate coupling states. To minimize the tunneling time between the fully coupled and fully decoupled states, the intermediate states could be either: (i) sampled with an optimal frequency distribution (the sampling problem) or (ii) selected with an optimal spacing distribution (staging problem). The sampling issue is addressed by determining the biasing weights that would allow generating an optimal ensemble; discretized versions of this algorithm (well suited for small number of coupling stages) are also presented. The staging problem is addressed by selecting the intermediate stages in such a way that a flat histogram is the optimized ensemble. The validity of the advocated methods is demonstrated by their application to two model problems, the solvation of large hard spheres into a fluid of small and large spheres, and the vapor-liquid equilibrium of a chain system.     

锂硫电池正极材料的制备及工艺优化

锂硫电池具有能量密度高、价格低等优势,有希望应用于下一代储能领域. 但锂硫电池仍然存在一些问题,如多硫化物穿梭效应、缺乏有效的锂硫电池规模制备工艺等. 为了解决这些问题,作者以不同商用碳材料（乙炔黑、科琴黑与碳纳米管）和单质硫复合作为正极材料,探究正极制备工艺对多硫化物穿梭效应抑制效果及锂硫电池性能的影响. 通过研究,作者得出以下结论：科琴黑作为单质硫的载体,与单质硫球磨8 h后,匹配粘结剂聚乙烯吡咯烷酮（PVP）制备的正极浆料可实现在涂布和辊压后极片的厚度达到500 μm、压实密度达到991.65 mg·cm ^-3. 作者将最终得到的正极极片应用于高硫载量锂硫软包电池,电池首圈放电容量为137.4 mA·h,经过10圈循环后,放电容量为115.5 mA·h,表现出优异的电化学性能. 该碳硫复合正极材料制备工艺有望在锂硫电池的宏量制备中获得应用.     

层板金属离子不同的钴基双氢氧化物制备及其电化学性能

通过调变层板中的三价金属离子制备了层板金属离子不同的钴基双氢氧化物(LDHs),X-射线衍射(XRD)和傅里叶变换红外(FTIR)测试表明,层板中金属离子的变化对LDHs的物理结构有较大影响。电化学性能比较表明,三价金属离子的改变对材料的有效工作电位窗口和大电流稳定性及循环容量保持率均有很大影响。由于二价与三价金属离子在电化学过程中的作用不同,Co-AlLDHs在1A·g-1的电流密度下比容量达到447F·g-1;Co-InLDHs与Co-CrLDHs则具有很好的循环稳定性和电容性质。     

Lignin derived porous carbon with favorable mesoporous contributions for highly efficient ionic liquid-based supercapacitors

Lignin and its derivatives hold great potential in developing high performance porous carbon materials for supercapacitors due to the versatile features of high carbon content, abundant multifunctional groups, low cost, and environmental benefits. Unfortunately, their derived porous carbon generally has the features of unfavorable microporous-dominated morphologies and low specific surface area (SSA) attributed from the highly-branched structure of lignin, which are hardly suitable for the supercapacitors with ionic liquid (IL) electrolyte, leading to poor energy density and rate capability. Herein, porous carbon materials with desirable mesoporous contributions from sodium lignosulphonate are designed via a facile template method. Such rich mesoporisity carbon materials not only possess with three-dimensional interconnected network, large SSA, as well as favorable pore size distribution for accelerated ion and electron mass transfer, but also feature low heteroatom content for high electrochemical stability. Consequently, the optimal electrode exhibits a high capacitance of 166 F/g at 0.5 A/g, superior rate performance (59 Wh/kg at 59 kW/kg), as well as impressive cycle life with good capacitance retention of 93.1% in EMIBF₄ electrolytes. The present work opens a new avenue to design porous carbon materials with high mesopore properties from lignin for effective compatibility with IL electrolyte in high-performance supercapacitors.