Ca1−xMo1−ySiyO4:Eux: A novel red phosphor for white light emitting diodes

Single phase of Ca_1−xMo_1−ySi_yO₄:Eu_x³⁺ (0.18?x?0.26, 0?y?0.04) was synthesized by solid-state method. The photoluminescence investigation indicated that Ca_1−xMoO₄:Eu_x³⁺ (0.18?x?0.26) could be effectively excited by 393 and 464 nm, and it exhibited an intense red emission at 615 nm. The introduction of Si⁴⁺ ions did not change the position of the peaks but strongly enhanced the emission intensity of Eu³⁺ under 393 and 464 nm excitations and showed very good color purity. The emission intensity of optimal Ca_0.8Mo_0.98Si_0.02O₄:Eu_0.2³⁺ sample (excited by 393 nm) was about 5.5 times higher than that of the phosphor Y₂O₂S:0.05Eu³⁺. So this phosphor could be nicely suitable for the application of the UV LED chips.     

Effect of boric acid on structure,morphology and luminescent properties of divalent europium doped calcium aluminate phosphors

Blue phosphors Ca_1 − xAl₂O₄: xEu²⁺ were prepared by high temperature solid-state method. Their structure, morphology and luminescent properties were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM) and fluorescence spectroscopy. The effect of different amounts of fluxing agent H₃BO₃ on structure, morphology and luminescent properties of blue phosphors Ca_1 − xAl₂O₄: xEu²⁺ luminous intensity caused by different amount of H₃BO₃ was also investigated. The amount of H₃BO₃ doped Ca_1 − xAl₂O₄: xEu²⁺ in optimal luminous intensity had been determined. The results showed that both the excitation and emission spectra of samples were all broad bands, and that the peak of emission spectra was near 442 nm, which was corresponding to the 4f⁶5d → 4f⁷ transition of Eu²⁺ illuminating blue light. Ca_1 − xAl₂O₄: xEu²⁺ (x = 3.5 mol%) could be gained with good morphology and the best luminous intensity when H₃BO₃ mass ratio was 0.5 wt%.     

Size-dependent microstructure and europium site preference influence fluorescent properties of Eu-doped Ca10(PO4)6(OH)2 nanocrystal

In this study, Eu³⁺-doped nanocrystalline Ca₁₀(PO₄)₆(OH)₂ (Ca_10−xEu_x(PO₄)₆(OH)₂) with different particle sizes have been prepared by the thermal decomposition of precursors. Size-dependent microstructure could be observed in nanocrystalline Ca_10−xEu_x(PO₄)₆(OH)₂. The lattices of Ca_10−xEu_x(PO₄)₆(OH)₂ nanocrystals were more distorted in comparison with the bulk, and the smaller the particle size, the more distorted the lattices. Room temperature photoluminescence showed europium site preference was also size-dependent, with the majority of Eu³⁺ ions occupying Ca(II) sites in the bulk, but more and more Eu³⁺ ions occupying Ca(I) sites in Ca_10−xEu_x(PO₄)₆(OH)₂ with decreasing particle size. Fluorescent properties of Ca_10−xEu_x(PO₄)₆(OH)₂ were considered to be influenced by both microstructure and site preference of Eu³⁺ ions. An abnormal strong intensity of ⁵D₀-⁷F₀ transition was observed in bulk and larger Ca_10−xEu_x(PO₄)₆(OH)₂ nanocrystals, but the relative intensities of ⁵D₀-⁷F₀ transition to ⁵D₀-⁷F_1,2,3,4 transition of Eu³⁺ became weaker as the particle sizes decreased. As the particle sizes became smaller, the ratios of the red emission transition (⁵D₀-⁷F₂) to the orange emission transition (⁵D₀-⁷F₁) (R/O values) first increased by comparing the bulk sample with 96 nm sample, and then decreased by comparing 96 nm sample to 57 nm sample. The quenching concentrations of Ca_10−xEu_x(PO₄)₆(OH)₂ samples increased with decreasing particle size. Possible mechanisms responsible for these phenomena were proposed. Since nanosized Ca_10−xEu_x(PO₄)₆(OH)₂ showed higher fluorescent intensities, higher R/O values and higher quenching concentrations, this material is considered to be a promising phosphor.     

Synthesis and luminous characteristics of Ba2MgSi2−xAlxO7: 0.1Eu, 0.1Mn phosphor for WLED

The shift of the emission band to longer wavelength (yellow-orange) of the Ba₂MgSi_2−xAl_xO₇: 0.1Eu²⁺ phosphor under the 350-450 nm excitation range has been achieved by adding the codoping element (Mn²⁺) in the host. The single-host silicate phosphor for WLED, Ba₂MgSi_2−xAl_xO₇: 0.1Eu²⁺, 0.1Mn²⁺ was prepared by high-temperature solid-state reaction. It was found experimentally that, its three-color emission peaks are situated at 623, 501 and 438 nm, respectively, under excitation of 350-450 nm irradiation. The emission peaks at 438 and 501 nm originate from the transition 5d to 4f of Eu²⁺ ions that occupy the two Ba²⁺ sites in the crystal of Ba₂MgSi_2−x Al_xO₇, while the 623 nm emission is attributed to the energy transfer from Eu²⁺ ions to Mn²⁺ ions. The white light can be obtained by mixing the three emission colors of blue (438 nm), green (501 nm) and red (623 nm) in the single host. When the concentrations of the Al³⁺, Eu²⁺ and Mn²⁺ ions were 0.4, 0.1 and 0.1 mol, respectively, the sample presented intense white emission. The addition of Al ion to the host leads to a substantial change of intensity ratio between blue and green emissions. White light could be obtained by combining this phosphor with 405 nm light-emitting diodes. The near-ultraviolet GaN-based Ba₂MgSi_1.7 Al_0.3O₇: 0.1Eu²⁺, 0.1Mn²⁺ LED achieves good color rendering of over 85.     

Luminescence properties of Y2WO6:Eu incorporated with Mo or Bi ions as red phosphors for light-emitting diode applications

In this study, the red phosphors, Y₂W_1−xMo_xO₆:Eu³⁺ and Y₂WO₆:Eu³⁺,Bi³⁺, have been investigated for light-emitting diode (LED) applications. In Y₂WO₆:Eu³⁺, the excitation band edge shifts to longer wavelength with the incorporation of Mo⁶⁺ or Bi³⁺ ions. The emission spectra exhibit ⁵D₀→⁷F₁ and ⁵D₀→⁷F₂ transition of Eu³⁺ ion at 588, 593, and 610 nm, respectively. Moreover, the bluish-green luminescence of the WO₆⁶⁻ at about 460 nm is observed to decrease with the incorporation of Mo⁶⁺, which results in pure red color. Thus, this study shows that the red phosphor, Y₂WO₆:Eu³⁺, incorporated with Mo⁶⁺ or Bi³⁺ ions is advantageous for LEDs applications.     

Synthesis and optical properties of red emitting Eu doped CaZrO3 phosphor

Eu³⁺ activated Ca_1−xEu_xZrO₃ (x = 0.01–0.05) phosphor with perovskite structure has been synthesized by sol–gel combustion method. The structure, morphology and optical properties of materials were characterized by X-ray diffraction, scanning electron microscopy and fluorescence spectrometry. The XRD results indicate that crystals of CaZrO₃:Eu³⁺ belongs to orthorhombic perovskite structure. The phosphors can be effectively excited by UV light and the emission spectra results indicate that red luminescence of CaZrO₃:Eu³⁺ due to electric dipole transition ⁵D₀ → ⁷F₂ at 616 nm is dominant. Thus, these prepared phosphors show remarkable luminescent properties which find applications in display devices.     

Effect of Ca and Sr alkaline earth ions on luminescence properties of BaAl12O19:Eu nanophosphor

Nanosized barium aluminate materials was doped by divalent cations (Ca²⁺, Sr²⁺) and Eu²⁺ having nominal compositions Ba_1−xMxAl₁₂O₁₉:Eu (M=Ca and Sr) (x=0.1-0.5), were synthesized by the combustion method. These phosphors were characterized by XRD, scanning electron microscopy-energy-dispersive spectrometry (SEM-EDS) and photoluminescence measurement. The photoluminescence characterization showed the presence of Eu ion in divalent form which gave emission bands peaking at 444 nm for the 320 nm excitation (solid-state lighting excitation), while for 254 nm it gave the same emission wavelength of low intensity (1.5 times) compared to 320 nm excitation. It was also observed that alkaline earth metal (Ca²⁺ and Sr²⁺) dopants increase the intensity of Eu²⁺ ion in BaAl₁₂O₁₉ lattice, thus this phosphor may be useful for solid-state lighting.     

Synthesis and photoluminescence characteristics of (Sr, Ca)3B2O6:Eu for application in white light-emitting diodes

A series of yellow-green (Sr, Ca)₃B₂O₆:Eu phosphors have been synthesized using precursors prepared via a facile sol-gel route. The solid-solution phases crystallized to materials with the formula of Sr_3−x−yCa_xEu_yB₂O₆ with varied Ca²⁺ and Eu²⁺ contents. The emission peak centered at 540 nm under near-UV excitation exhibited a broad-band distribution in the range of 450-650 nm. The dependences of the luminescence intensity on the contents of Ca²⁺ substitution and Eu²⁺ dopant were also investigated. The composition in the host lattice sensitively affected the chromaticity index. Sr_1.21Ca_1.7Eu_0.09B₂O₆ (SCB:0.09Eu) was shown to possess the highest intensity and broadest emission band. Calcining temperature was shown to greatly influence the luminescent properties of SCB:0.09Eu. It is concluded that SCB:0.09Eu can be used as an efficient yellow-green phosphor for white light-emitting diodes (white LEDs) applications.     

Improved luminescent properties of red-emitting Ca0.54Sr0.16Eu0.08Gd0.12(MoO4)0.2(WO4)0.8 phosphor for LED application by charge compensation

The red-emitting Ca_0.54Sr_0.16Eu_0.08Gd_0.12(MoO₄)_0.2(WO₄)_0.8 phosphor is improved in the emission charateristics by charge compensation, of which chromaticity coordinates (CIE) are x=0.66 and y=0.33. Three approaches to charge compensation are investigated, namely (a) 3Ca²⁺/Sr²⁺→2Eu³⁺/Gd³⁺+vacancy, (b) 2Ca²⁺/Sr²⁺→Eu³⁺/Gd³⁺+M⁺(M⁺ is a monovalent cation like Li⁺, Na⁺ and K⁺ employed as a charge compensator) and (c) Ca²⁺/Sr²⁺→Eu³⁺/Gd³⁺+N⁻ (N⁻ is a monovalent anion like F⁻, Cl⁻, Br⁻ and I⁻ employed as charge compensation ions). Through photoluminescent spectra analyzing the radiative and non-radiative relaxation mechanisms of luminescent system are obtained. Under 20 mA forward-bias current, one red-emitting LED is made by combining 390-405 nm-emitting LED chip and the phosphor. The red-emitting phosphor has broad prospects in LED application field.     

Photoluminescence properties of Eu in Y(PO3)3 under VUV excitation

The photoluminescence properties of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) are investigated. The excitation spectrum of Y_0.85(PO₃)₃:0.15Eu₃⁺ shows that both the (PO₃)₃³⁻ groups and the CT bands of O²⁻-Y³⁺ can efficiently absorb the excitation energy in the region of 120-250 nm. Under 147 nm excitation, the optimal emissive intensity of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) is about 36% of the commercial phosphor (Y,Gd)BO₃:Eu³⁺, which hints that the absorbed energy by the host matrix could be efficiently transferred to Eu³⁺. We try to study the concentration quenching mechanism of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) under 147 and 172 nm excitation.     

Photoluminescence properties of Sr1-xSi2O2N2: Eux as green to yellow-emitting phosphor for blue pumped white LEDs

This study evaluated potential applications of green to yellow-emitting phosphors (Sr_1−xSi₂O₂N₂: Eu²⁺_x) in blue pumped white light emitting diodes. Sr_1-xSi₂O₂N₂: Eu²⁺_x was synthesized at different Eu²⁺ doping concentrations at 1450 °C for 5 h under a reducing nitrogen atmosphere containing 5% H₂ using a conventional solid reaction method. The X-ray diffraction patterns of the prepared phosphor (Sr_1-xSi₂O₂N₂: Eu²⁺_x) were indexed to the SrSi₂O₂N₂ phase and an unknown intermediate phase. The photoluminescence properties of these phosphors (Sr_1−xSi₂O₂N₂: Eu²⁺_x) showed that the samples were excited from the UV to visible region due to the strong crystal field splitting of the Eu²⁺ ion. The emission spectra under excitation of 450 nm showed a bright color at 545-561 nm. The emission intensity increased gradually with increasing Eu²⁺ doping concentration ratio from 0.05 to 0.15. However, the emission intensity decreased suddenly when the Eu²⁺ concentration ratio was >0.2. As the doping concentration of Eu²⁺ was increased, there was a red shift in the continuous emission peak. These results suggest that Sr_1-xSi₂O₂N₂: Eu₂⁺_x phosphor can be used in blue-pumped white light emitting diodes.     

Luminescence studies of rare earth doped yttrium gadolinium mixed oxide phosphor

This paper reports the photoluminescence and thermoluminescence properties of gamma ray induced rare earth doped yttrium gadolinium mixed oxide phosphor. The europium (Eu³⁺) was used as rare earth dopant. The phosphor was prepared by chemical co-precipitation method according to the formula (Y_2−x−yGd_x) O₃: Eu_y³⁺ (x=0.5; y=0.05). The photoluminescence emission spectrum of the prepared phosphor shows intense peaks in the red region at 615 nm for ⁵D₀→⁷F₂ transitions and the photoluminescence excitation spectra show a broad band located around 220–270 nm for the emission wavelength fixed at 615 nm. The thermoluminescence studies were carried out after irradiating the phosphor by gamma rays in the dose range from 100 Gy to 1 KGy. In the thermoluminescence glow curves, one single peak was observed at about 300 °C of which the intensity increases linearly in the studied dose range of gamma rays. The glow peak was deconvoluted by GlowFit program and the kinetic parameters associated with the deconvoluted peaks were calculated. The kinetic parameters were also calculated by various glow curve shape and heating rate methods.     

Studies in crystal structure and luminescence properties of Eu-doped metal tungstate phosphors for white LEDs

The correlation between the crystal structure and luminescent properties of Eu³⁺-doped metal tungstate phosphors for white LEDs was investigated. Red-emitting A_4−3x(WO₄)₂:Eu_x³⁺ (A=Li, Na, K) and B_(4−3x)/2(WO₄)₂:Eu_x³⁺ (B=Mg, Ca, Sr) phosphors were synthesized by solid-state reactions. The findings confirmed that these phosphors exhibited a strong absorption in the near UV to green range, due to the intra-configurational 4f-4f electron transition of Eu³⁺ ions. The high doping concentration of Eu³⁺ enhanced the absorption of near UV light and red emission without any detectable concentration quenching. Based on the results of a Rietveld refinement, it was attributed to the unique crystal structure. In the crystal structure of the Eu³⁺-doped metal tungstate phosphor, the critical energy transfer distance is larger than 5 Å so that exchange interactions between Eu³⁺ ions would occur with difficulty, even at a high doping concentration. The energy transfer between Eu³⁺ ions, which causes a decrease in red emission with increasing concentration of Eu³⁺, appears to be due to electric multi-polar interactions. In addition, the Eu-O distance in the host lattice affected the shape of emission spectrum by splitting of emission peak at the ⁵D₀→⁷F₂ transition of Eu³⁺.     

Bridging between structure and optimum luminescence for nearly monodispersed Ce1−xGdxF3:Eu3+ nanoparticles

This work reports a systematic study on bridging between structure and optimum luminescence for Ce_1?xGd_xF₃:Eu³⁺ nanoparticles. It is found that all Ce_1?xGd_xF₃:Eu³⁺ nanoparticles were nearly monodispersed, showing average grain diameter of 30–35 nm. Regardless of the dopant level, all nanocrystals crystallized in a single hexagonal phase. With increasing Gd³⁺ content, the lattice dimension for Ce_1?xGd_xF₃:Eu³⁺ linearly decreased, which was followed by the highly distorted lattice symmetry surrounding Eu³⁺. The consequence of the structural modification is that the color purity was significantly improved. Furthermore, the excitation energy of Ce³⁺ in the ultraviolet range was efficiently transferred to Eu³⁺ ions via the sensitizer Gd³⁺, which significantly enhanced the red emission and showed a maximized quantum efficiency of 59.7%.     

PL and EL characterizations of ZnO:Eu, Li films derived by sol-gel process

ZnO:Eu³⁺, Li⁺ films prepared by the dip-coating method were characterized by photoluminescence (PL) and electroluminescence (EL). When the ZnO:Eu³⁺, Li⁺ films were excited using UV light with energy corresponding to the band-to-band excitation of the host matrix, the PL spectra showed emissions from both ZnO and Eu³⁺ ions, while their EL spectra showed emissions only from Eu³⁺ ions, and no emission from ZnO could be detected. It is found that the EL emission intensity B is dependent on the applied voltage, B=B_o exp(−bV^−1/2). With increasing frequency, the EL intensity dramatically increases at lower frequencies (<1000 Hz), and then increases gradually at higher frequencies (>1000 Hz).     

Synthesis and luminescence properties of red-emitting phosphors NaY0.87Eu0.13(WO4)1.2(MoO4)0.8

A series of NaY_1−yEu_y(WO₄)_2−x(MoO₄)_x (x=0−2 and y=0.06−0.15) phosphors have been prepared by a combustion route. X-ray powder diffraction, photoluminescence excitation and emission spectra were used to characterize the resulting samples. The excitation spectra of these phosphors show the strongest absorption at about 396 nm, which matches well with the commercially available n-UV-emitting GaN-based LED chip. Their emission spectra show an intense red emission at 616 nm due to the ⁵D₀→⁷F₂ electric dipole transition of Eu³⁺. As the Mo content increases, the intensity of the ⁵D₀→⁷F₂ emission of Eu³⁺ activated at wavelength of 396 nm increases and reaches a maximum when the relative ratio of Mo/W is 2:3. The intense red-emission of the tungstomolybdate phosphors at near-UV excitation suggests that the material is a potential candidate for white light emitting diode (WLEDs).     

Low-voltage cathodoluminescence property of Li-doped Gd2−xYxO3:Eu

Cathodoluminescent (CL) spectra of Li-doped Gd_2−xY_xO₃:Eu³⁺ solid-solution (0.0?x?0.8) were investigated at low voltages (300 V-1 kV). The CL intensity is maximum for the composition of x=0.2 and gradually reduces with increasing the amount of substituted Y content. In particular, small (∼100 nm) particles of Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ are obtained by firing the citrate precursors at only 650°C for 18 h. Relative red-emission intensity at 300 V of this phosphor is close to 180% in comparison with that of commercial red phosphor Y₂O₃:Eu³⁺. An increase of firing temperature to 900°C results in 400-600 nm sized spherical particles. At low voltages (300-800 V), the CL emission of 100 nm sized particles is much stronger than that of 400-600 nm sized ones. In contrast, the larger particles exhibit the higher CL emission intensity at high voltages (1-10 kV). Taking into consideration small spherical morphology and effective CL emission, Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ appears to be an efficient phosphor material for low voltage field emission display.     

Control of luminescence and conductivity of delafossite-type CuYO2 by substitution of rare earth cation (Eu, Tb) and/or Ca cation for Y cation

Delafossite-type oxides of CuTb_yY_1−yO₂, CuEu_yY_1−yO₂, CuCa_xTb_yY_1−x−yO₂ and CuCa_xEu_yY_1−x−yO₂ have been prepared by solid state reactions. The lattice-parameter dependence on the composition implies substitution of the Tb³⁺, Eu³⁺ and Ca²⁺ cations for the Y³⁺ site. Noticeable sharp emission lines due to the f-f transitions (⁵D₄→⁷F_J, J=3-6) of Tb³⁺ or due to the f-f transitions (⁵D₀→⁷F_J, J=0-4) of Eu³⁺ are observed at room temperature. Electrical conductivities of CuCa_xTb_yY_1−x−yO₂ and CuCa_xEu_yY_1−x−yO₂ are larger than those of CuTb_yY_1−yO₂ and CuEu_yY_1−yO₂, indicating the increase of the hole concentration caused by the substitution of Ca²⁺ for the Y³⁺ site. These results indicate the controllability of the luminescence and conductivity in CuCa_xTb_yY_1−x−yO₂ and CuCa_xEu_yY_1−x−yO₂ delafossite-type oxides by simultaneous substitution of the rare earth Tb³⁺ or Eu³⁺ cation and the Ca²⁺ cation for the Y³⁺ site.     

Improved color purity in nano-size Eu-doped YBO3 red phosphor

Nano-size YBO₃:Eu³⁺ phosphor has been synthesized by the co-precipitation method. X-ray diffraction (XRD) pattern confirmed the formation of hexagonal vaterite-type structures of YBO₃:Eu³⁺ nanoparticles. The transmission electron microscopy (TEM) study revealed the formation of spherical YBO₃:Eu³⁺ nanoparticles with size 20-40 nm. The photoluminescence spectra revealed that the ratio of the red emission (⁵D₀-⁷F₂) to the orange emission (⁵D₀-⁷F₁) was much higher in the synthesized nano-size YBO₃:Eu³⁺ phosphor. The improved relative intensity, i.e., higher R/O value of emission peaks, is due to a lower symmetry of crystal field around Eu³⁺ ions.     

Photoluminescence properties of Eu in lithium titanate

Lithium titanate ceramics doped with Eu were synthesized and their photoluminescence (PL) and emission spectral characteristics were investigated. PL spectra of the sample showed peaks corresponding to the ⁵D₀→⁷F_J (J=0, 1, 2, 3 and 4) transitions under 230 nm excitation. The fluorescence lifetimes of Eu³⁺ ions were found out to be 645 μs. Strong red emission coming from the hypersensitive ⁵D₀→⁷F₂ transition of Eu³⁺ ion suggested the presence of the dopant ion in highly asymmetric environment. Further analysis of the emission spectrum revealed that the symmetry of the metal ion is very low i.e. C₂. The emission intensity of the sample was compared with a commercial phosphor to get an idea about the commercial utility of the phosphor. Various emission properties for the system namely Judd-Ofelt intensity parameters, spontaneous emission probabilities, branching ratios, radiative lifetimes and quantum efficiency were evaluated for the dopant ion by adopting standard procedure.