Dielectric and optical behaviors in relaxor ferroelectric Pb(In1/2Nb1/2)1−xTixO3 crystal

Dielectric permittivities (ε′,ε″) have been measured as functions of temperature (140-535 K) and frequency (500 Hz-2.0 MHz) in a (001)-cut Pb(In_1/2Nb_1/2)_0.7Ti_0.3O₃ (PINT30%) single crystal grown by the modified Bridgman method with Pb(Mg_1/3Nb_2/3)_0.71Ti_0.29O₃ (PMNT29%) seed crystal. A diffused phase transition was observed in the temperature region of ∼430-460 K with strong frequency dispersion. Above the Burns temperature T_B≅510 K, the dielectric permittivity was found to follow the Curie-Weiss behavior, ε′=C/(T−T_C), with parameters C=3.9×10⁵ and T_C=472 K. Below T_B≅510 K, polar nanoclusters are considered to appear and are responsible for the diffused dielectric anomaly. Optical transmission, refractive indices, and the Cauchy equations were obtained as a function of wavelength at room temperature. The unpoled crystal shows almost no birefringence, indicating that the average structural symmetry is optically isotropic. The crystal exhibits a broad transparency in the wavelength range of ∼0.4-6.0 μm.     

Dielectric properties and phase transitions of (Pb0.87La0.02Ba0.1)(Zr0.6Sn0.4−xTix)O3 ceramics with compositions near AFE/RFE phase boundary

The electrical properties and phase transition behavior of (Pb_0.87La_0.02Ba_0.1)(Zr_0.6Sn_0.4−xTi_x)O₃ solid solutions (PLBZST, 0.04≤x0.2) were investigated by the X-ray diffraction, permittivity, pyroelectric current, and P-E electric hysterisis loops. As the composition x increased from 0.04 to 0.2, the antiferroelectric ceramics (x≤0.07, AFE) with tetragonal phase changed to the ferroelectric relaxors (RFE, 0.09≤x). AFE ceramics showed a peculiar diffuse phase transition and dielectric relaxation at the low temperature (down to −100 °C) due to a frustration between AFE and FE state. With an increase in composition x, electrically field-induced AFE-FE switching field (E_AFE-FE) and AFE-paraelectric (PE) phase transition temperature (T_c) are depressed in the temperature (T)-Ti composition (x) phase diagram, a FE-AFE-PE triple phase point (T_tr) with the lowest transition temperature occurred at x=0.09. The pyroelectric currents under an application of various external electric field (E) were measured to identify a T-E phase diagram of the PLBZST compound.     

Ferroelectric properties of Bi3.25−x/3La0.75Ti3−xNbxO12 films prepared by pulsed laser deposition

Bi₄Ti₃O₁₂ (BiT), Bi_3.25La_0.75Ti₃O₁₂ (BLT), Bi_4−x/3Ti_3−xNb_xO₁₂ (BTN) and Bi_3.25−x/3La_0.75Ti_3−xNb_xO₁₂ (BLTN) thin films have been prepared by pulsed laser deposition. BTN and BLTN films exhibit a maximum in the remanent polarization P_r at a Nb content x=0.018. At this Nb content, the BLTN film has a P_r value (25 μC/cm²) that is much higher than that of BiT and a coercive field similar to that of BiT. The polarization of this BLTN film is fatigue-free up to 10⁹ switching cycles. The high fatigue resistance is mainly due to the substitution of Bi³⁺ ions by La³⁺ ions at the A site and the enhanced P_r arises largely from the replacement of Ti⁴⁺ ions by Nb⁵⁺ ions at the B site. The mechanisms behind the effects of the substitution at the two sites are discussed.     

Ferroelectric properties of highly c-axis oriented Bi4−xLaxTi3O12 film-based capacitors

Highly c-axis oriented lanthanum-modified bismuth titanate (Bi_4−xLa_xTi₃O₁₂) films having a variety of lanthanum (La) contents were grown on Pt/TiO₂/SiO₂/Si(100) substrates using metal-organic sol deposition and subsequent annealing at 650 °C for 1 h. After systematically examining the ferroelectric properties of Bi_4−xLa_xTi₃O₁₂ films as a function of the La-content, it was concluded that the film with x=0.85 had the largest remanent polarization in the direction parallel to the c-axis. The Pt/Bi_3.15La_0.85Ti₃O₁₂/Pt capacitor showed a well-saturated polarization-electric field (P-E) switching curve with the switching remanent polarization (2P_r) value of 33 μC/cm² and the coercive field (E_c) of 68 kV/cm at an applied voltage of 10 V. More importantly, the capacitor exhibited fatigue-free behavior up to 6.5×10¹⁰ read/write switching cycles at a frequency of 1 MHz. The capacitor also demonstrated an excellent charge-retaining ability and a strong resistance against the imprinting failure.     

Maxwell-Wagner characterization of dielectric relaxation in Ni0.8Zn0.2Fe2O4/Sr0.5Ba0.5Nb2O6 composite

Dense composites were prepared through incorporating the dispersed Ni_0.8Zn_0.2Fe₂O₄ ferromagnetic particles into Sr_0.5Ba_0.5Nb₂O₆ ferroelectric matrix. Extrinsic dielectric relaxation and associated high permittivities of the materials are reported in the composites. We used an ideal equivalent circuit to explain electrical responses in impedance formalism. A Debye-like relaxation in the permittivity formalism was also found. Interestingly, real permittivity (ε′) of the sample containing 30% Ni_0.8Zn_0.2Fe₂O₄ shows obvious independence of the temperature at 100 kHz. Dielectric relaxation and high-ε′ properties of the composites are explained in terms of the Maxwell-Wagner (MW) polarization model.     

Compositional dependence of ferroelectric properties of highly c-axis oriented Bi4−xNdxTi3O12 film capacitors

Highly c-axis oriented neodymium-modified bismuth titanate (Bi_4−xNd_xTi₃O₁₂) films having a variety of neodymium (Nd) contents were successfully grown on Pt/TiO₂/SiO₂/Si(100) substrates using metal-organic sol decomposition. After systematically examining ferroelectric properties of the c-axis oriented Bi_4−xNd_xTi₃O₁₂ film capacitors as a function of the Nd-content, we concluded that the capacitor with x=0.85 had the largest remanent polarization. The Bi_3.15Nd_0.85Ti₃O₁₂ capacitor fabricated using a top Pt electrode showed well-saturated polarization-electric field (P-E) switching curves with the remanent polarization (P_r) of 51 μC/cm² and the coercive field (E_c) of 99 kV/cm at an applied voltage of 10 V. More importantly, the Pt/Bi_3.15Nd_0.85Ti₃O₁₂/Pt capacitor exhibited fatigue-free behavior up to 4.5×10¹⁰ read/write switching cycles at a frequency of 1 MHz. The capacitor also demonstrated an excellent charge-retaining ability and a strong resistance against the imprinting failure.     

Effects of composition on phase structure and electrical properties of (K0.5Na0.5)0.90Li0.06Sr0.02Nb(1−x)SbxO3 ceramics

Lead-free (K_0.5Na_0.5)_0.90Li_0.06Sr_0.02Nb_(1−x)Sb_xO₃ (KNLSN-Sb_x) ceramics were synthesized by ordinary sintering technique. The compositional dependence of phase structure and electrical properties of the ceramics was systematically investigated. All samples possessed pure perovskite structure, showing room temperature symmetries of orthorhombic at x<0.01, coexistence of orthorhombic and tetragonal phases at x=0.01, and tetragonal at 0.02≤x≤0.05. The temperature of the polymorphic phase transition (PPT) was shifted to lower temperature and dielectric relaxor behavior was induced by increasing Sb content. The samples near the coexistence region (x=0.01) exhibited enhanced electrical properties: d₃₃∼145 pC/N, k_p∼38% and P_r∼20.4 μC/cm².     

Investigations of structural, dielectric and ferroelectric behavior of europium substituted SrBi2Ta2O9 ferroelectric ceramics

Europium substituted samples of the compositions Sr_1−xEu_xBi₂Ta₂O₉ (x=0.0,0.025,0.050,0.10 and 0.20) were synthesized by solid state reaction method and studied for their structural, dielectric and ferroelectric properties. The X-ray diffractograms confirmed the formation of single phase layered perovskite structure in all the samples. The temperature variation of dielectric constant shows that the Curie temperature (T_c) decreases on increasing concentration of europium. The dielectric loss reduces significantly with europium addition. The P-E studies of the Eu-substituted SBT ceramics show that the remanent polarization increases with increasing concentration of europium.     

Enhanced ferroelectric properties of (Pb0.90La0.10)Ti0.975O3 multilayered thin films prepared by RF magnetron sputtering

The (Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PLT/PT), PbTiO₃/(Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PT/PLT/PT) multilayered thin films with a PbO_x buffer layer were in situ deposited by RF magnetron sputtering at the substrate temperature of 600 °C. With this method, highly (1 0 0)-oriented PLT/PT and PT/PLT/PT multilayered thin films were obtained. The PbO_x buffer layer leads to the (1 0 0) orientation of the films. The dielectric, ferroelectric and pyroelectric properties of the PLT multilayered thin films were investigated. It is found that highly (1 0 0)-oriented PT/PLT/PT multilayered thin films possess higher remnant polarization 2P_r (44.1 μC/cm²) and better pyroelectric coefficient at room temperature p (p = 2.425 × 10⁻⁸ C/cm² K) than these of PLT and PLT/PT thin films. These results indicate that the design of the PT/PLT/PT multilayered thin films with a PbO_x buffer layer should be an effective way to enhance the dielectric, ferroelectric and pyroelectric properties. The mechanism of the enhanced ferroelectric properties was also discussed.     

Ferroelectric properties of Pr and Nb co-substituted Sr0.8Bi2.2Ta2O9 thin films

Thin film of both A- and B-site co-substituted Sr_0.8Bi_2.2Ta₂O₉ (SBT) by Pr³⁺ and Nb⁵⁺, i.e. Sr_0.8Pr_0.1Bi_2.1Ta_1.5Nb_0.5O₉ (SPBTN) was fabricated on Pt/Ti/SiO₂/Si substrates by metalorganic decomposition method. The Nb⁵⁺ substitution at B-site and Pr³⁺ substitution at A-site enhanced the remanent polarization and reduced the coercive field of the films, respectively. The remanent polarization (2P_r) value of the SPBTN film was 22 μC/cm². The coercive field (2E_c) value of the SPBTN film was 102 kV/cm, which was much lower than that of SBTN (165 kV/cm). The effects of substitution on structural and ferroelectric properties of SBT were discussed in detail. As a result, the A- and B-sites co-substitution may be one of the promising ways to improve ferroelectric properties of SBT.     

Bias field effects on the dielectric properties of 0.67Pb(Mg1/3Nb2/3)O3-0.33PbTiO3 single crystals with different orientations

The domain states and phase transitions in 0.67Pb(Mg_1/3Nb_2/3)O₃-0.33PbTiO₃ single crystals were investigated by studying their relative permittivity under various dc bias at constant heating and cooling rates. The orientation dependence of the bias field effect was revealed by examining the temperature dependence of relative permittivity as a function of crystal orientation (the 〈111〉, 〈011〉 and 〈001〉 directions) and dc bias field. The crystals basically have a macrodomain rhombohedral ferroelectric state in the ferroelectric phase under zero dc bias. External bias field could modulate the domain state and induce a stable macrodomain state in the crystals. Also, it is proposed that the dc bias applied along the 〈001〉 or 〈011〉 direction could induce a tetragonal ferroelectric phase or an orthorhombic ferroelectric phase, respectively, in an intermediate temperature range.     

TiO2-nonstoichiometry dependence on piezoelectric properties and depolarization temperature of (Bi0.5Na0.5)0.94Ba0.06TiO3 lead-free ceramics

(Bi_0.5Na_0.5)_0.94Ba_0.06Ti_xO_1+2x lead-free piezoceramics with x varying from 0.97 to 1.03 were fabricated and characterized in order to investigate the effects of TiO₂-nonstoichiometry on the piezoelectric properties and depolarization temperature of (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ composition. X-ray diffraction (XRD) analysis showed that all samples have a single phase of perovskite structure with rhombohedral symmetry. Piezoelectric and dielectric measurements revealed that deficiency of TiO₂ leads to an increase in the piezoelectric coefficient (d₃₃), free relative permittivity (), and loss tangent (tan δ) besides an increase in the electromechanical coupling coefficient (k_p) within a certain amount, while excess of TiO₂ results in a decrease in k_p, d₃₃, and , but an increase in tan δ. Depolarization temperature (T_d) measurement indicated a decrease and an increase in T_d as a result of increasing TiO₂ deficiency and TiO₂ excess, respectively. This TiO₂-nonstoichiometry also induced changes in the remanent polarization (P_r) and coercive field (E_c) of the ceramics.     

Electromechanical properties and dielectric behavior of (Bi1/2Na1/2)(1−1.5x)BixTiO3 lead-free piezoelectric ceramics

Bismuth doped bismuth sodium titanate ceramics [(Bi_1/2Na_1/2)_(1−1.5x)Bi_xTiO₃, x=0 to 0.06] were prepared, and the resulting effects on the microstructure and dielectric properties were examined. All of the Bi-doped ceramics exhibited a single phase of perovskite structure with rhombohedral symmetry. The poling leakage current was significantly reduced by the doping of Bi, facilitating the poling process of the ceramics. The doping with Bi enhances the piezoelectric properties and increases the dielectric constant and the dielectric loss of the ceramics. At 2 mol% Bi-doping level, the ceramics exhibit a large remanent polarization of 47 μC/cm² and a relatively low coercive field of 71 kV/cm, while their d₃₃ and k_p reach a maximum value of 95 pC/N and 21%, respectively.     

Multiferroic properties of Bi0.8La0.2FeO3/CoFe2O4 multilayer thin films

Bi_0.8La_0.2FeO₃/CoFe₂O₄ (BLFO/CFO) multilayer thin films (totally 20 layers BLFO and 19 layers CFO) were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. X-ray diffraction and transmission electron microscope measurements show that the films are polycrystalline and consisted of multilayered structure. Ferroelectric hysteresis loops with remnant polarization and saturated polarization of 4.2 and 13.3 μC/cm², respectively, were observed. On the other hand, the films show well-shaped magnetization hysteresis loops with saturated and remnant magnetization of 34.7 and 11.4 emu/cm³, respectively, which are significantly larger than pure BLFO thin films deposited under the same conditions. These results indicate that constructing epitaxial superlattice might be a promising way to fabricate multiferroics with improved properties.     

Relaxor behavior of (Ba,Sr)(Zr,Ti)O3 ferroelectric ceramics

We examine the ferroelectric-relaxor behavior of (Ba_0.65Sr_0.35)(Zr_0.35Ti_0.65)O₃ (BSZT) ceramics in the temperature range from 80 to 380 K. A broad dielectric maximum, which shifts to higher temperature with increasing frequency, signifies the relaxor-type behavior of these ceramics. The value of the relaxation parameter γ∼2 estimated from the linear fit of the modified Curie-Weiss law, indicates the relaxor nature of the BSZT ceramics. The dielectric relaxation rate follows the Vogel-Fulcher relation with T_VF=107 K, E_a=0.121 eV, and ν₀=6.83×10¹⁴ Hz, further supports such relaxor nature. The slim P-E hysteresis loop and ‘butterfly’ shape dc bias field dependence of permittivity at T>T_m (T_m, the temperature of permittivity maximum) clearly signifies the occurrence of nanopolar clusters, which is the typical characteristic of ferroelectric relaxor. At 300 K and 10 kHz, the dielectric constant and loss tan δ are ∼1100 and 0.0015, respectively. The high tunability (∼25%) and figure of merit (∼130) at room temperature show that the BSZT ceramics could be a promising candidate for tunable capacitor applications.     

Electronic structures and ferroelectric properties of ABi2Ta2O9 (A=Ca, Sr, and Ba)

The electronic structures of ABi₂Ta₂O₉ (A=Ca, Sr, and Ba) were calculated by using first-principles under optimized structure. As the size of A-site cation decreases from that of Ba²⁺ to Ca²⁺, the band-gap between O 2p and Ta 5d increases from 2.0 to 2.9 eV, which responses to the stronger orbital hybridizations between Ta 5d and O 2p orbits favoring improvement of the ferroelectric property, decrease in leakage current, and increase in both spontaneous polarization and Curie temperature by the structural distortion. In contrast to CaBi₂Ta₂O₉ and SrBi₂Ta₂O₉, the hybridization between Ba 5p orbits and O 2p orbits in BaBi₂Ta₂O₉ has better structural stability.     

Controllable microstructures and multiferroic properties of Pb(Zr0.53Ti0.47)O3-CoFe2O4 composite films

1-3 and 2-2 types Pb(Zr_0.53Ti_0.47)O₃-CoFe₂O₄ (PZT-CFO) composite films with controllable microstructures, consisted by CFO nanopillar embedded in PZT matrix and PZT-CFO gratings respectively, have been fabricated on Pt/Ti/SiO₂/Si substrates by combining lithography technology and pulsed laser deposition. X-ray diffraction confirms that the films are well crystallized under optimized postannealing conditions. Scanning electron microscope reveals that the periodic microstructures can be well controlled. Especially, intrinsic room temperature ferroelectric and ferrimagnetic behaviors are observed simultaneously. The structure-properties relationship is discussed. Our results may provide an alternative method to design and prepare multiferroic composite films with controllable microstructures.     

Low temperature specific heat of bi-layered manganites La2−2xSr1+2xMn2O7 (x=0.3 and 0.5)

The specific heat (C) of bi-layered manganites La_2−2xSr_1+2xMn₂O₇ (x=0.3 and 0.5) is investigated for the ground state of low temperature excitations. A T^3/2 dependent term in the low temperature specific heat (LTSH) is identified at zero magnetic field and suppressed by magnetic fields for x=0.3 sample, which is consistent with a ferromagnetic metallic ground state. For x=0.5 sample, a T² term is observed and is consistent with a two-dimensional (2D) antiferromagnetic insulator. However, it is almost independent of magnetic field within the range of measured temperature (0.6-10 K) and magnetic field (6 T).     

The effect of potential of impedance in the pulsed-laser-deposited SrBi2Ta2O9 thin film

Ferroelectrics SrBi₂Ta₂O₉ (SBTO) thin films were grown on a highly oriented Pt/Ti/SiO₂/Si substrates using the pulsed laser ablation. The ac impedance of SBTO thin films have been measured at room temperature both in the frequency range from 10⁻¹ to 10⁶ Hz and bias voltage range from −6 to 6 V. The ac impedance dispersion was observed at low frequency with increasing bias voltage, which was interpreted based on a blocked charge. We can explain that the blocking interface gives rise to constant phase element (CPE) response, and we give an impedance model function that can fit data along the low frequency range when such a CPE is found. The low frequency dispersion phenomena of SBTO thin film are related to a charge diffusion process at the surface of thin film.