The aggregation behavior of poly-(oxyethylene)-poly-(oxypropylene)-poly-(oxyethylene)-block-copolymers in aqueous solution

Aqueous solutions of blockcopolymers, consisting of a polyoxypropyleneblock (POP) with a polyoxyethylene-block (POE) at each side, were studied using surface and interfacial tension measurements, static and dynamic light scattering and smallangle neutron scattering techniques, electric birefringence, rheological and DSC-measurements. The compounds were commercial samples and had an approximate average composition EO₂₀PO₇₀EO₂₀, EO₁₈PO₅₈EO₁₈, and EO₁₀₆PO₆₉EO₁₀₆. All three compounds formed micelles above a critical concentration. The size of the micellar core is determined by the length of the hydrophobic poly-propyleneoxide block. The transfer energy of a propyleneoxide unit from the aqueous to the micellar phase is about 0.3 kT at room temperature and hence a quarter of the corresponding value for a CH₂-group.The aggregation number of the micelles increases strongly with increasing temperature while the hydrodynamic radius remains constant in first approximation. The smallangle neutron scattering (SANS) data show at higher concentrations a strong correlation peak. Both the SANS- and the light-scattering data can be interpreted on the basis of the theory of hard sphere particles.Solutions with a volume fraction beyond about 0.2 gellifie when the temperature is raised above a characteristic value that is at the lowest concentrations slightly above room temperature, shift to lower values with increasing concentrations. Below this gelation temperature DSC-measurements show a phase transition with enthalpies between 40J/g and 80J/g, which is probably due to the dehydration of the PO-groups; this transition can also be observed at low concentrations where no gelation takes place. The position of the correlation peak of the SANS-data is not affected by the gel formation. Some samples, however, show clear evidence of long-range order and seem therefore to consist of cubic liquid crystalline phases. The shear moduli of the gels can qualitatively be understood on the basis of hard sphere models.     

Micelle hydration by1H-NMR

¹H-NMR studies were carried out for solution of amphiphilic betaine ester derivatives (of the general formula (CH₃)₃N⁺CH₂COOC _n H_2n+1Cl^– (V-n), wheren=10, 12, 14, and 16) andn-dodecyltrimethylammonium chloride (I-12). The spectra were taken at concentrations above and below critical micelle concentrations and chemical shifts were analyzed. It was stated that micelles are hydrated at the depth of the two CH₂ groups in the case ofV-n and the CH₂COO group in the case ofI-12. Therefore, the CH₂COO group during the micellization behaves as if it were CH₂CH₂ group.     

Interface stabilization and micelle formation in blends with a block copolymer

The phase separation behavior of ternary blends of two homopolymers, PMMA and PS, and a block copolymer of styrene and methylmethacrylate, P(S-b-MMA), was studied. The homopolymers were of equal chain length and were kept at equal amounts. Two copolymers were used with blocks of equal length, which exceeded or equaled that of the homopolymer chains. Varied was the copolymer contentf. Films were cast from toluene, which is a nonselective solvent. The morphologies of the cast films were compared with the structure of the critical fluctuations in solution, which were calculated in mean field approximation. The axis of blend compositionsf can be divided into parts of dominating macrophase and microphase separation. Above a transition concentrationf _o, all copolymer chains are found in phase interfaces. Belowf _o, part of them form micelles within the homopolymer phases.     

Ringing gels: Their structure and macroscopic properties

The phase diagram of the ternary surfactant system which consists of dimethyltetradecylaminoxide, hydrocarbon, and water contains a highly elastic gel phase which borders on the micellarL ₁-phase. This gel phase is transparent, optically isotropic, and shows the ringing phenomena when it is excited to mechanical vibrations. From SANS and light-scattering measurements it is shown that this phase consists of the same spherical microemulsion droplets which are present in the adjacent micellar solution. Even in the micellar solution the droplets are fairly monodisperse and in the SANS scattering functions a second scattering maximum was observed. Both the light scattering and SANS data can be described quantitatively on the basis of hard sphere interactions between the particles. Furthermore, it is shown that elasticity and shear modulus of the gel phase, which were determined experimentally, correlate with the compressibility modulus as calculated from the scattering data. The elasticity modulus and hence the osmotic compressibility modulus are related to the Laplace pressure inside the globules. For the calculation of this pressure it is possible to take the interfacial tension, which is obtained from a dilute micellar solution against the hydrocarbon which is used for the system. The radius of the particles and the hydrocarbon content in the system can be increased when some of the dimethyltetradecylaminoxide is replaced by dimethyltetradecylphosphinoxide.     

New conducting polymers, 3. Doping,stability, electrical,and optical characteristics of poly-(P-phenylphosphoethynediyl)

Studies on direct-current electrical conductivity and optical properties of a new solution of processable conducting polymer are reported. Electrical conductivity of thin films of the polymer on glass plate at room temperature was 6×10⁻⁶ S/cm. Study of conductivity with variation of temperature does not provide any definite thermal activation energy, which is in accordance with the amorphous nature of polymer. Optical absorption data adopting the Bardeen equation showed that maximum ‘optical gap’ (E _g ) is 3.30 eV. Doping with Br₂-vapor was found to be only partially effective in decreasingE _g by 0.43 eV. The polymer was found to be quite stable under normal atmospheric conditions. Environmental stability of both undoped and doped polymer has been discussed. Part 2: [5]     

Light scattering study of solution properties of bovine serum albumin,insulin, and polystyrene under moderate pressure

Brillouin scattering experiments have been performed on very dilute solutions of bovine serum albumin (BSA) in pH=4.7,I=0.1 M NaCl; insulin in pH=7.5,I = 0.1 M NaCl and polystyrene latex suspensions in aqueous medium at room temperatureT = 20₁ °C. The samples were first characterized by quasi-elastic light scattering (QELS) to determine the translational diffusion coefficient (D _T), hydrodynamic radius (R _H), and polydispersity of each of the samples at normal pressure. Subsequently, the samples were subjected to Brillouin scattering studies where the spectrum of the scattered light was analyzed by using a piezo-electric scannend five-pass Fabry-Perot interferometer. The hydrostatic pressure (P) acting on the samples was varied in the range from 1B to 825 B in steps of 100 B each. The pressure dependence of the measured sound velocityV _s (P) could be least square fitted tov _s (P)=A₀ +A ₁ P +A ₂ P ² with experimental error (± 1 %). This data has been interpreted consistent with an earlier work within the framework of modified Tait's equation of state and presumption of linear pressure dependence of the adiabatic bulk modulus in the moderate pressure regime.     

Lyotropic liquid crystalline phase behavior of a polymeric amphiphile polymerized via their hydrophilic ends

The reaction of the nonionic low molecular mass surfactant 3, 6, 9, 12, 15, 18, 21, 24-octaoxaoctatriacontane-1-ol (CH₃(CH₂)₁₃(OCH₂CH₂)₈OH, C₁₄E₈) with acryloyl chloride yielded the monomeric amphiphile II (CH₃(CH₂)₁₃(OCH₂CH₂)₈O₂C-(CH:CH₂) with the polymerizable group located at the hydrophilic end of the molecule. Using radical polymerization, the polymeric surfactant III is obtained. These three surfactant water systems exhibit lyotropic liquid crystalline phases. The binary phase diagrams are compared with each other. In changing from the monomer-water to the polymer-water system a stabilization of the lyotropic mesophases is observed with amphiphiles which are connected via their hydrophilic ends; it is known for the surfactants to be connected via their hydrophobic ends. The appearance of the inverse mesophases, as expected from the molecular geometry of the polymer, is not observed.     

Structure relaxation after temperature jumps in homogeneous polystyrene/poly(styrene-co-bromostyrene) blends

Concentration fluctuations in polymer blends and their change after a temperature jump were studied by time-dependent small angle X-ray scattering experiments. Measurements were conducted on homogeneous mixtures of polystyrene and a partially brominated derivative. Structure factors in thermal equilibrium show the form given by the random phase approximation, thus enabling a direct determination of the-parameter and the mean radius of gyration. TheT-dependence of can be understood as the result of superposed enthalpic contributions and a free volume term. In theT-jump experiments, samples were quenched to temperatures near T_g. Relaxation occurs on the time scale of minutes and is nonexponential, becoming slower with time. Initial relaxation rates increase with increasing scattering vectorsq in accordance with theoretical predictions.     

New organosols of ZnS and HgS in N,N-dimethylformamide and dimethyl sulfoxide. Use in the preparation of semiconductive polymer-metal sulfide composite films

Organosols of ZnS and HgS in N,N-dimethylformamide (DMF) and dimethyl sulfoxide (DMSO) were prepared by reaction of Zn and Hg salts with H₂S. ZnS in the DMF organosol has a particle size of about 300 Å, determined by an argon laser scattering technique. The form of HgS in the organosols varies with temperature, concentration of HgS, and type of solvent;-HgS in a DMF organosol is converted into-HgS at –30 °C or above. Poly(acrylonitrile)-ZnS or -HgS composite films prepared from organosols are semiconductive, and the electrical conductivity of the film increases by a factor of 10²–10³ on exposure to moisture or alcohol vapour. Poly(acrylonitrile)--HgS composite films, prepared from heated-HgS, show electrical conductivity of a range of 10^–1–10^–2 S cm^–1 and a large electron mobility.     

Interfacial effects on the ageing behavior of high density polyethylene filled with glass spheres

The stress relaxation and creep behavior of unfilled high density polyethylene (HDPE) and HDPE filled with untreated and surface-treated glass spheres were measured at room temperature. A silane-based coupling agent capable of providing a covalent bond between HDPE and the glass spheres was used for the surface-treatment. Two different amounts of the coupling agent were employed giving silane layers on the fillers with different thicknesses. The effect of ageing time at room temperature on the viscoelastic properties after quenching from 100 °C to room temperature in ice water was also investigated. The effects of the surface treatment of the fillers and the ageing time was characterized by means of the internal stress ( _i ) concept. The _i -value increased with the degree of interaction of the filler/matrix interface and the ageing time. It was here not possible to superimpose the different flow curves with regard to the ageing time with sufficient accuracy. This is due to the variation of _i with ageing time. The surface-treatment of the filler had a marked effect on the creep behavior at high applied stress levels and on the ageing behavior of the composites, presumably due to the formation of an interphase region close to the filler surface with different properties and different ageing characteristics than that of the bulk of the matrix.     

Infrared and raman studies on the phase structure of barium ethyl(octyl)phosphate-water system

Barium ethyl(alkyl)phosphates, as new simple surfactants ((C₂H₅O)(RO)-PO ₂ ^– )₂Ba²⁺ with various chain length ofR, were synthesized. The infrared spectra in the CH stretching region were measured for these surfactants in the solid state and in aqueous solution, and assignments were made. In particular, the ordering and environment of octyl chains in the different phases of the barium ethyl(octyl)phosphate-water system were studied by the Fourier-transform-infrared and Raman spectra. The CH stretching bands in the infrared spectra reflected the ordering and environment of octyl chains in each phase. The Raman band connected to the PO ₂ ^– symmetric stretching mode was sensitively shifted. This was caused by the change of aggregation structures with different Ba²⁺...PO ₂ ^– interaction. The infrared band arising from the PO ₂ ^– antisymmetric stretching mode was insensitive to the phase structures. The C–C stretching region in the infrared spectra was used to discuss the ordering of each phase.     

Small-angle neutron scattering on shear-induced micellar structures

Small-angle neutron scattering (SANS) experiments on sheared aqueous surfactant solutions of tetradecyltrimethylammoniumsalicylate (TTMA-Sal) are reported. A5-mM-solution without shear shows a weak correlation peak at a momentum transfer of 0.09 nm^–1 which has its origin in the micellar interaction. For shear rates above a threshold value of =40 s^–1 the scattering pattern shows an irregular increase in anisotropy. The analysis of the anisotropic pattern reveals the existence of two types of micelles: Small rodlike micelles which are weakly aligned and very large rodlike aggregates which are strongly aligned and which are present above the threshold value of. The two micelles are in equilibrium with each other and the equilibrium shifts with increasing shear rate to the side of the large oriented micelles.     

Gas transport properties of poly(2,2,4,4-tetramethyl cyclobutane carbonate)

Gas transport properties of semicrystalline films of poly(2,2,4,4-tetramethyl cyclobutane carbonate) (TMCBPC) were studied. Permeability coefficients for He, O₂, N₂, CH₄, and CO₂ at 35°C for pressures between 1 and 20 atm are reported as well as sorption isotherms for N₂, CH₄, and CO₂ at the same conditions. The permeability coefficients for TMCBPC are larger than corresponding values for the aromatic bisphenol-A polycarbonate (PC) and tetramethyl bisphenol-A polycarbonate (TMPC), even though the TMCBPC films are semicrystalline. These results are explained on the basis of the larger free volume available for permeation in this polymer. Significant TMCBPC plasticization by CO₂ was also observed and this causes typical time-dependent behavior. The plasticization process starts at very low pressures compared with the behavior of aromatic polycarbonates PC and TMPC. This early onset of plasticization seems to be related also to the larger free volume in the amorphous phase of TMCBPC which favors high gas sorption. The diffusion coefficients for TMCBPC are also larger than those reported for the aromatic polycarbonates PC and TMPC. Ideal gas separation factors were found to follow the usual trend; that is, as permeability increases, the ideal separation factor decreases. © 1993 John Wiley & Sons, Inc.     

XPS analysis (ESCA) of the surface composition of poly(styrene/2-hydroxyethyl methacrylate) microspheres produced by emulsifier-free emulsion polymerization

Polymer microspheres composed of various compositions of styrene and 2-hydroxyethyl methacrylate (HEMA) were produced by batch emulsifier-free emulsion polymerization. The HEMA content at the surface, [HEMA] _s , of the microspheres powdered by freeze-drying was determined by both quantitativeC ^1s /O ^1s analysis andC ^1s peak shape analysis of the x-ray photoelectron spectroscopic spectra. When the HEMA content in the microsphere, [HEMA] _p , was less than about 5 mole%, the [HEMA] _s values determined by the two different methods showed good agreement. At [HEMA]_p above 5 mole %, [HEMA]_s values determined by the first method were about 15 mole % greater than those determined by the second. They both showed a similar tendency with the [HEMA] _s being higher than the [HEMA] _p , e.g., when [HEMA] _p was 1 mole %, [HEMA] _s was 11 mole %. The intensity of the satellite peak due to the ^* transition of the benzene ring of the styrene component decreased with an increase in [HEMA] _p , to zero at 5 mole % of [HEMA] _p . These results indicate that the HEMA component is localized at the surface.Part CVIII of the series Studies on Suspension and Emulsion.     

Lipolysis of didecanoyl-lecithin/triolein mixed monolayers by phospholipaseA 2

A study of enzyme lipolysis by pancreatic phospholipaseA ₂ and by vipera berus phospholipaseA ₂ on monomolecular mixed films of didecanoyl-lecithin and triolein on an aqueous subphase of pH 8 has been carried out. The influence of the composition of the mixed film, the surface pressure of the film and the amount and type of the injected enzyme on the lipolysis rate were studied.In order to relate the lipolytic activity with the monolayer state, the compression isotherms of the didecanoyl-lecithin/triolein mixed monolayers have also been obtained.The resuls are compared to observations on lipolytic activity of phospholipaseA ₂ on the didecanoyl-lecithin/cholesterol mixed monolayers. Triolein improves the kinetic conditions of the lipolysis of lecithin films in a higher degree than cholesterol. Probably it increases the enzyme penetration by the fluidifying effect exerted on the lecithin monolayers.     

Gas permeability of block copolymers of styrene and butadiene

The permeability of styrene-butadiene block copolymer foils with different composition prepared by casting and pressing has been investigated for the gases Ar, CO₂, and CH₄ at pressure difference of 400 mbar and at the temperature range 298 T [K] 333.The permeation process can be described by the solution diffusion mechanism. The diffusion coefficients decrease in the sequence of the gases Ar, CO₂, and CH₄ and the solubility coefficients increase in the sequence Ar, CH₄, CO₂.The dependence of the permeability on the composition of the block copolymer can be interpreted by the help of percolation theory and the effective medium theory. It follows the critical volume fraction of the percolation of the transport phase _PB ^c (= 0,23) and the coordination numberz (= 4) giving an information concerning the multiphase structure of the block copolymer.Presented in part at the 33^rd Annual Meeting of the Colloid-Gesellschaft, Graz, Austria, September 14–16, 1987.     

Polymer adsorption on fine particles; the effects of particle size and its stability

The effects of particle size on polyacrylamide (PAAm,M _w =59×10⁴, 500×10⁴) adsorption were investigated using a series of well-characterized hematite (-Fe₂O₃) dispersions. The -Fe₂O₃ particles with highly monodisperse and nearly spherical shape ranged in radius from 23 nm to 300 nm. the maximum amount of PAAm adsorption (M _m ) in each system, showed a steady increase with decreasing particle radius and was influenced strongly by particle concentrations in the medium. Furthermore, it was realized that the diameter of -Fe₂O₃ particles after treatment with PAAm under different particle concentrations decreased with increasing particle concentration. The relation between particle concentration in the medium and particle size after treatment was also influenced by the medium pH, i.e., at the medium pH close to the isoelectric point of -Fe₂O₃ particles (pH^o=9.2), the particle size after treatment increased with increasing particle concentration. All these results suggest that in the system of ultra-fine particles, the mixing process between particle-particle and polymerparticle will play an important role on the conformation of adsorbed polymer layer.     

Small-angle neutron scattering of colloidal silica dispersions in a non-polar solvent

Small-angle neutron scattering studies were performed on dilute dispersions of colloidal silica spheres in mixtures of h₁₂- and d₁₂-cyclohexane. The particles consisted of a SiO₂-core and a layer of stearyl alcohol molecules terminally attached with a chemical bond (Si-O) to the particle surface. The contrast variation method was applied to reveal the internal structure of the particles. The matchpoints determined with this method were in accordance with those calculated from the mass density of the particles and the atomic composition, as determined with elemental analysis.For a detailed interpretation of the scattering curves, we assumed that the particles were spherosymmetrical and consisted of two concentric layers. With the relation we derived between the radius of gyration and the reciprocal contrast for such a model, it was possible to determine all the parameters characterizing the particle in terms of this model. The model calculations performed using these parameters fitted very well to the experimental intensities for high contrasts. For lower contrasts, the fit was somewhat less good. This is probably due to random fluctuations in the scattering length density within the particle core.The different radii as found by neutron scattering, agreed very well with those determined using other techniques, such as light scattering (static and dynamic) and electron microscopy.     

Effects of uniaxial stretching and shrinkage on proton spin-lattice and spin-spin relaxation times of isotactic polypropylene

An isotactic polypropylene film was stretched at 120 °C in poly(ethylene glycol) and thermally shrunk at various temperatures. Proton spin-lattice,T ₁, and spin-spin,T ₂, relaxation times were measured using a broad line pulse spectrometer operating at 19.8 MHz in the temperature range 40 °C–100 °C. The temperature ofT ₁ minimum shifts to higher temperatures and the value ofT ₁ minimum increases in magnitude as the stretching ratio is increased. In contrast the temperature ofT ₁ minimum shifts to lower temperatures as shrinkage is increased, whereas the value ofT ₁ minimum increases in magnitude because of the increase in crystallimty during shrinkage. T_2a, the longestT ₁ associated with the mobile amorphous regions, increases during shrinkage, indicating that chain mobility in the amorphous regions increases substantially during shrinkage. It was found that an orientation function of the amorphous regions,f _a, correlates well withT _2a .Presented in part at the 52nd Annual Meeting of the Japan Chemical Society, Kyoto, April 1986.     

Melittin and ionic surfactant interactions in monomolecular films

The interaction between the anionic and cationic surfactants with Melittin spread monolayers at the air-water interface was investigated. The addition of anionic Cl^–, under the films of Melittin gives rise to a change in both surface pressure and surface potential. These interactions are different when surfactants are present, due to specific interactions between Melittin and the ionic-surfactants.