分子印迹基质固相分散-液相色谱法测定牛奶中的氯霉素残留

以对模板分子具有较强识别特性的分子印迹聚合物为基质固相分散吸附剂, 提取牛奶中痕量氯霉素, 最后用HPLC法测定. 研究了氯霉素分子印迹聚合物对样品中氯霉素的提取和净化效果, 在优化条件下, 方法的检出限为0.15 ng/mL, 定量限为0.50 ng/mL. 不同氯霉素添加量的回收率大于93.2%, RSD＜5.9%. 方法适用于牛奶中氯霉素残留的测定.     

Determination of trace bisphenol A in complex samples using selective molecularly imprinted solid-phase extraction coupled with capillary electrophoresis

The highly selective, fast and effective sample pretreatment technique molecularly imprinted solid-phase extraction (MISPE) can overcome the low sensitivity of the highly efficient capillary electrophoresis-UV method (CE-UV). In this work, narrowly dispersible bisphenol A (BPA)-imprinted polymeric microspheres with a high capacity factor of k′ = 6.8 and an imprinted factor of I = 6.53 were investigated as selective solid-phase extraction (SPE) sorbents for use in extraction of BPA from different sample matrices (tap water, wastewater, Yangtze River water, soil from the Yangtze River, shrimp and human urine). Washing and eluting protocols of MISPE were optimized. Under optimal conditions, recoveries of MISPE were investigated. Recoveries were basically constant and the relative standard deviation (RSD) was lower than 5.8% when loading volumes changed from 1 to 50 mL. Recoveries ranged from 71.20% to 86.23% for different sample matrices. Compared with C18 SPE, MISPE had higher selectivity and recovery for BPA. BPA was determined with good accuracy and precision in different complex samples using CE-UV coupled with MISPE. Spiked recoveries ranged from 95.20% to 105.40%, and the RSD was less than 7.2%. Because a large loading volume was achieved, the enrichment efficiency of pretreatment and the sensitivity of this method were improved. The limits of detection of this MISPE-CE-UV method for BPA in tap water, wastewater, Yangtze River water, soil from the Yangtze River, shrimp and human urine were 3.0 μg L^− 1, 5.4 μg L^− 1, 6.9 μg L^− 1, 2.1 μg L^− 1, 1.8 μg L^− 1 and 84 μg L^− 1, respectively.     

A new molecularly imprinted polymer for selective extraction of cotinine from urine samples by solid-phase extraction

Cotinine, the main metabolite of nicotine in human body, is widely used as a biomarker for assessment of direct or passive exposure to tobacco smoke. A method for molecularly imprinted solid-phase extraction (MISPE) of cotinine from human urine has been investigated. The molecularly imprinted polymer (MIP) with good selectivity and affinity for cotinine was synthesized using cotinine as the template molecule, methacrylic acid as the functional monomer, and ethylene glycol dimethacrylate as the cross-linker. The imprinted polymer was evaluated for use as a SPE sorbent, in tests with aqueous standards, by comparing recovery data obtained using the imprinted form of the polymer and a non-imprinted form (NIP). Extraction from the aqueous solutions resulted in more than 80% recovery. A range of linearity for cotinine between 0.05 and 5 μg mL⁻¹ was obtained by loading 1 mL blank urine samples spiked with cotinine at different concentrations in acetate buffer of pH 9.0, and by using double basic washing and acidic elution. The intra-day coefficient of variation (CV) was below 7% and inter-day CV was below 10%. This investigation has provided a reliable MISPE–HPLC method for determination of cotinine in human urine from both active smokers and passive smokers. Figure     

Multivariate optimization of molecularly imprinted polymer solid-phase extraction applied to parathion determination in different water samples

In this work a parathion selective molecularly imprinted polymer was synthesized and applied as a high selective adsorber material for parathion extraction and determination in aqueous samples. The method was based on the sorption of parathion in the MIP according to simple batch procedure, followed by desorption by using methanol and measurement with square wave voltammetry. Plackett-Burman and Box-Behnken designs were used for optimizing the solid-phase extraction, in order to enhance the recovery percent and improve the pre-concentration factor. By using the screening design, the effect of six various factors on the extraction recovery was investigated. These factors were: pH, stirring rate (rpm), sample volume (V₁), eluent volume (V₂), organic solvent content of the sample (org%) and extraction time (t). The response surface design was carried out considering three main factors of (V₂), (V₁) and (org%) which were found to be main effects. The mathematical model for the recovery percent was obtained as a function of the mentioned main effects. Finally the main effects were adjusted according to the defined desirability function. It was found that the recovery percents more than 95% could be easily obtained by using the optimized method. By using the experimental conditions, obtained in the optimization step, the method allowed parathion selective determination in the linear dynamic range of 0.20-467.4 μg L⁻¹, with detection limit of 49.0 ng L⁻¹ and R.S.D. of 5.7% (n = 5). Parathion content of water samples were successfully analyzed when evaluating potentialities of the developed procedure.     

Development of andrographolide molecularly imprinted polymer for solid-phase extraction

A method employing molecularly imprinted polymer (MIP) as selective sorbent for solid-phase extraction (SPE) to pretreat samples was developed. The polymers were prepared by precipitation polymerization with andrographolide as template molecule. The structure of MIP was characterized and its static adsorption capacity was measured by the Scatchard equation. In comparison with C(18)-SPE and non-imprinted polymer (NIP) SPE column, MIP-SPE column displays high selectivity and good affinity for andrographolide and dehydroandrographolide for extract of herb Andrographis paniculata (Burm.f.) Nees (APN). MIP-SPE column capacity was 11.9±0.6 μmol/g and 12.1±0.5 μmol/g for andrographolide and dehydroandrographolide, respectively and was 2-3 times higher than that of other two columns. The precision and accuracy of the method developed were satisfactory with recoveries between 96.4% and 103.8% (RSD 3.1-4.3%, n=5) and 96.0% and 104.2% (RSD 2.9-3.7%, n=5) for andrographolide and dehydroandrographolide, respectively. Various real samples were employed to confirm the feasibility of method. This developed method demonstrates the potential of molecularly imprinted solid phase extraction for rapid, selective, and effective sample pretreatment.     

Selective solid-phase extraction of amoxicillin and cephalexin from urine samples using a molecularly imprinted polymer

In this paper we describe, for the first time, a molecularly imprinted polymer (MIP) for the antibiotic amoxicillin (AMX), synthesised by a noncovalent molecular imprinting approach and used to extract AMX selectively from urine samples. The MIP was applied as a molecularly selective sorbent in molecularly imprinted SPE (MISPE) in an off-line mode, where it showed useful cross-selectivity for a structurally related antibiotic, cephalexin (CPX). By using a MISPE protocol, the MIP was able to selectively extract both AMX and CFX from 5 mL of water spiked with 10 mg/L with recoveries of 75 and 78% for AMX and CFX, respectively. When applied to real samples (urine) at clinically relevant concentrations, recoveries from 2 mL of human urine spiked with 20 mg/L decreased slightly to 65 and 63% for AMX and CFX, respectively. To demonstrate further the selectivity of the MIP obtained, a comparison with commercially available SPE cartridges was performed. Improvements in the retention of both AMX and CFX on the MIP were obtained relative to the commercially available cartridges, and the MISPE extracts were considerably cleaner, due to molecularly selective analyte binding by the MIP.     

Development of a selective molecularly imprinted polymer-based solid-phase extraction for indomethacin from water samples

A selective molecularly imprinted solid-phase extraction (MISPE) for indomethacin (IDM) from water samples was developed. Using IDM as template molecule, acrylamide (AM) or methacrylic acid (MAA) as functional monomer, ethylene dimethacrylate (EDMA) as crosslinker, and bulk or suspension polymerization as the synthetic method, three molecularly imprinted polymers (MIPs) were synthesized and characterized with a rebinding experiment. It was found that the MIP of AM-EDMA produced by bulk polymerization showed the highest binding capacity for IDM, and so it was chosen for subsequent experiments, such as those testing the selectivity and recognition binding sites. Scatchard analysis revealed that at least two kinds of binding sites formed in the MIP, with the dissociation constants of 7.8 μmol L⁻¹ and 127.2 μmol L⁻¹, respectively. Besides IDM, three structurally related compounds — acemetacin, oxaprozin and ibuprofen — were employed for selectivity tests. It was observed that the MIP exhibited the highest selective rebinding to IDM. Accordingly, the MIP was used as a solid-phase extraction sorbent for the extraction and enrichment of IDM in water samples. The extraction conditions of the MISPE column for IDM were optimized to be: chloroform or water as loading solvent, chloroform with 20% acetonitrile as washing solution, and methanol as eluting solvent. Water samples with or without spiking were extracted by the MISPE column and analyzed by HPLC. No detectable IDM was observed in tap water and the content of IDM in a river water sample was found to be 1.8 ng mL⁻¹. The extraction efficiencies of the MISPE column for IDM in spiked tap and river water were acceptable (87.2% and 83.5%, respectively), demonstrating the feasibility of the prepared MIP for IDM extraction. Figure Molecularly imprinted polymer-based solid-phase extraction for indomethacin     

Determination of donepezil in serum samples using molecularly imprinted polymer nanoparticles followed by high‐performance liquid chromatography with ultraviolet detection

A molecularly imprinted polymer designed for the selective extraction of donepezil from serum samples was synthesized using a noncovalent molecular imprinting approach. The molecularly imprinted polymer was evaluated chromatographically and then its affinity for donepezil was confirmed by solid‐phase extraction. The optimal conditions for solid‐phase extraction were provided by cartridge conditioning using acidified water purified from a Milli‐Q system, sample loading under basic aqueous conditions, clean‐up using acetonitrile, and elution with methanol/tetrahydrofuran. Desirable molecular recognition properties of the molecularly imprinted polymer led to good donepezil recoveries (90–102%). The data indicated that the imprinted polymer has a perfect selectivity and affinity for donepezil and could be used for selective extraction and analysis of donepezil in human serum.     

Molecularly imprinted solid-phase extraction and flow-injection chemiluminescence for trace analysis of 2,4-dichlorophenol in water samples

Highly sensitive flow-injection chemiluminescence (CL) combined with molecularly imprinted solid-phase extraction (MISPE) has been used for determination of 2,4-dichlorophenol (2,4-DCP) in water samples. The molecularly imprinted polymer (MIP) for 2,4-DCP was prepared by non-covalent molecular imprinting methods, using 4-vinylpyridine (4-VP) and ethylene glycol dimethacrylate (EGDMA) as the monomer and cross-linker, respectively. 2,4-DCP could be selectively adsorbed by the MIP and the adsorbed 2,4-DCP was determined by its enhancing effect on the weak chemiluminescence reaction between potassium permanganate and luminol. The enhanced CL intensity was linear in the range from 1 × 10⁻⁷ to 2 × 10⁻⁵g mL⁻¹. The LOD (S/N = 3) was 1.8 × 10⁻⁸g mL⁻¹, and the relative standard deviation (RSD) was 3.0% (n = 11) for 1.4 × 10⁻⁶g mL⁻¹. The proposed method had been successfully applied to the determination of 2,4-DCP in river water. Figure Effect of 4-VP content on the ultraviolet spectrum of 2,4-DCP in chloroform     

儿茶素活性成分分子印迹聚合物的固相萃取研究

以表没食子儿茶素没食子酸酯(Epigallocatechin-gallate,EGCG)为模板分子,α-甲基丙烯酸为功能单体,乙二醇二甲基丙烯酸酯为交联剂,在光冷引发条件下合成EGCG分子印迹聚合物,利用该聚合物制成分子印迹固相萃取柱,用于固相萃取茶叶提取物茶多酚,对萃取柱中的清洗液、洗脱剂、上载量等进行了选择.结果表明,在萃取柱上载样品之后,先用V(甲醇):V(水)＝1:9溶液进行清洗,再用V(甲醇):V(乙酸)＝9:1混合液进行目标分子的洗脱,可以得到比较纯的目标物质EGCG(色谱峰相对峰面积达92.4%),萃取柱在上载样品并进行清洗、洗脱之后,EGCG的回收率达69.3%.分子印迹柱具有较好的稳定性和耐用性能,使用20次后其选择性识别能力仍未降低,但空白印迹柱却没有这样的选择性识别能力.     

Fast and selective extraction of chloramphenicol from soil by matrix solid‐phase dispersion using molecularly imprinted polymer as dispersant

The molecularly imprinted polymer (MIP) was synthesized and used as dispersant of matrix solid‐phase dispersion (MSPD) for the extraction of chloramphenicol (CAP) in soil samples. The satisfactory recovery of CAP was obtained by the optimized extraction conditions: 1:2 as the ratio of sample to MIPs; 5 min as the dispersion time; 30% aqueous methanol as washing solvent and methanol as elution solvent. The CAP extracted from soil was determined by LC‐MS/MS. The slight ion suppression phenomenon was observed for the CAP when the sample was cleaned up by MSPD with MIP as dispersant, when compared with C18 as MSPD dispersant, which caused significant ion suppression. LOD of CAP is 4.1 ng/g. RSDs of intra‐ and inter‐day tests ranging from 3.1 to 6.2% and from 3.9 to 8.3% are obtained. At all three fortified levels (20, 100 and 500 ng/g), recoveries of CAP are in the range of 86.9–92.6%. The effect of ageing time of spiked soil sample on the CAP recovery was examined. The CAP recovery decreased from 91.0 to 36.9% when the ageing time changed from 1 day to 4 wk.     

A new molecularly imprinted polymer for the on-column solid-phase extraction of diethylstilbestrol from aqueous samples

The estrogenic compound diethylstilbestrol (DES) is widely studied because of its potential endocrine disruption effects. The prohibition of the use of diethylstilbestrol as a growth promoter has not been enough to ensure the total disappearance of this compound from environmental matrices. Due to the low levels of DES present in the environment, preconcentration and clean up methods are necessary for its analysis. This paper describes the synthesis and use of a molecularly imprinted polymer (MIP) as sorbent for on-column solid-phase extraction of DES from aqueous samples. The selectivity of the DES-MIP was evaluated towards several selected estrogens such as hexestrol (HEX), estrone (E1), estriol (E3), estradiol (E2) and ethynylestradiol (EE2). HPLC-DAD was used to quantify all analytes at 230-nm wavelength. The method has been successfully applied to the analysis of DES in spiked river and tap water samples, with recoveries of 72% and 83% respectively.     

Solid-phase molecularly imprinted pre-concentration and spectrophotometric determination of isoxicam in pharmaceuticals and human serum

A selective molecularly imprinted polymer (MIP) has been synthesized for isoxicam pre-concentration, followed by its spectrophotometric determination based on hydrogen bonding interactions between examined drug and alizarin yellow GG. This method is able to evaluate isoxicam in range of 1.0 × 10⁻³ to 20.0 μg mL⁻¹, with a limit of determination of 1.0 ng mL⁻¹. The retention capacity and pre-concentration factor of prepared sorbent are 18.5 mg g⁻¹ and 200, respectively; and the prepared MIPs can be reused at least for five times. The MIP capability for isoxicam selection and extraction from the solution is higher than non-imprinted polymer (NIP). Under optimum conditions, this procedure can be successfully applied to assay trace amounts of isoxicam in pharmaceutical and biological samples.     

Selective solid-phase extraction of tebuconazole in biological and environmental samples using molecularly imprinted polymers

Molecularly imprinted polymers (MIPs) were prepared by precipitation polymerization using tebuconazole (TBZ) as a template. Frontal chromatography and selectivity experiments were used to determine the binding capabilities and binding specificities of different MIPs. The polymer that had the highest binding selectivity and capability was used as the solid-phase extraction (SPE) sorbent for the direct extraction of TBZ from different biological and environmental samples (cabbage, pannage, shrimp, orange juice and tap water). The extraction protocol was optimized and the optimum conditions were: conditioning with 5 mL methanol:acetic acid (9:1), 5 mL methanol and 5 mL water respectively, loading with 5 mL aqueous samples, washing with 1.2 mL acetonitrile (ACN):phosphate buffer (5:5, pH3), and eluting with 3 mL methanol. The MIPs were able to selectively recognize, effectively trap and preconcentrate TBZ over a concentration range of 0.5–15 μmol/L. The intraday and interday RSDs were less than 9.7% and 8.6%, respectively. The limit of quantification was 0.1 μmol/L. Under optimum conditions, the MISPE recoveries of spiked cabbage, pannage, shrimp, orange juice and tap water were 62.3%, 75.8%, 71.6%, 89% and 93.9%, respectively. MISPE gave better HPLC separation efficiencies and higher recoveries than C18 SPE and strong cation exchange (SCX) SPE. Figure HPLC analysis of spiked pannage after MISPE (A) and after C18 SPE (B). HQ (1), E3 (2), p-NP (3), FTF (4), TBZ (5), PNZ (6), HXZ (7) Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.     

Selective recognition of Triamterene in biological samples by molecularly imprinted monolithic column with a pseudo template employed

Melamine (MAM) was employed as a pseudo template to prepare a molecularly imprinted polymer monolithic column which presents the ability of selective recognition to Triamterene (TAT), whose structure was similar to that of MAM. Methacrylic acid and ethylene glycol dimethacrylate were applied as functional monomer and cross‐linker, respectively, during the in situ polymerization process. Chromatographic behaviors were evaluated, the results indicated that the molecularly imprinted polymer monolithic column possessed excellent affinity and selectivity for TAT, and the imprinting factor was high up to 3.99 when 7:3 of ACN/water v/v was used as mobile phase. In addition, the dissociation constant and the binding sites were also determined by frontal chromatography as 134.31 μmol/L and 132.28 μmol/g, respectively, which demonstrated that the obtained molecularly imprinted polymer monolith had a high binding capacity and strong affinity ability to TAT. Furthermore, biological samples could be directly injected into the column and TAT was enriched with the optimized mobile phase. These assays gave recovery values higher than 91.60% with RSD values that were always less than 3.5%. The molecularly imprinted monolithic column greatly simplified experiment procedure and can be applied to preconcentration, purification, and analysis of TAT in biological samples.     

Preparation and evaluation of molecularly imprinted ionic liquids polymer as sorbent for on-line solid-phase extraction of chlorsulfuron in environmental water samples

In this report, vinylimidazolium ionic liquid as a functional monomer for preparation of chlorsulfuron (CS) imprinted polymers were first studied. The imprinted materials showed high selectivity for CS, and fast kinetics so that adsorption equilibrium was achieved within 5 min. These materials have been further employed to detect trace CS from water samples by online preconcentration coupled with HPLC. The sorbent offered good linearity (0.005-30 μg L(-1), r(2)>0.99) for on-line solid-phase extraction of trace chlorsulfuron. Under the optimal experimental conditions, the recovery for chlorsulfuron was in the range of 81.0-110.1% for the water samples, with RSDs ranging from 1.2 to 7.6%.     

Continuous solid-phase extraction and preconcentration of bisphenol A in aqueous samples using molecularly imprinted columns

A bisphenol A (BPA) molecularly imprinted polymer, the composition of which was optimised using a chemometric approach, has been applied to the selective preconcentration of the template from aqueous samples. The selectivity of the polymer toward BPA and related compounds was evaluated chromatographically. The BPA-imprinted polymer was packed in a column and used for continuous on-column solid-phase extraction (MISPE) of aqueous samples followed by subsequent analysis by HPLC with fluorescence detection of the eluted fractions. The composition of the washing solvent applied in the MISPE procedure was optimised to favour the specific interactions of the MIP with BPA and to remove the non-selectively bound matrix components. The MISPE method has proven to be effective for selective preconcentration of BPA in aqueous samples (recoveries >84% obtained in the eluate for 10–100 mL sample volumes) enabling detection and quantification limits of 1.0 and 3.3 ng mL^–1, respectively (based on 25 mL sample size). Analytical recoveries were between 92 and 101% for river water samples spiked with known amounts of BPA (30, 60, and 80 ng mL^–1); relative standard deviations (RSD) were lower than 5.0%.     

Preparation and evaluation of molecularly imprinted solid-phase micro-extraction fibers for selective extraction of phthalates in an aqueous sample

A novel molecularly imprinted polymer (MIP) that was applied to a solid-phase micro-extraction (SPME) device, which could be coupled directly to gas chromatograph and mass spectrometer (GC/MS), was prepared using dibutyl phthalate (DBP) as the template molecule. The characteristics and application of this fiber were investigated. Electron microscope images indicated that the MIP-coated solid-phase micro-extraction (MI-SPME) fibers were homogeneous and porous. The extraction yield of DBP with the MI-SPME fibers was higher than that of the non-imprinted polymer (NIP)-coated SPME (NI-SPME) fibers. The MI-SPME fibers had a higher selectivity to other phthalates that had similar structures as DBP. A method was developed for the determination of phthalates using MI-SPME fibers coupled with GC/MS. The extraction conditions were optimized. Detection limits for the phthalate samples were within the range of 2.17-20.84 ng L⁻¹. The method was applied to five kinds of phthalates dissolved in spiked aqueous samples and resulted in recoveries of up to 94.54-105.34%, respectively. Thus, the MI-SPME fibers are suitable for the extraction of trace phthalates in complicated samples.     

Molecularly imprinted matrix solid-phase dispersion combined with dispersive liquid-liquid microextraction for the determination of four Sudan dyes in egg yolk

A new kind of aniline-naphthol molecularly imprinted microsphere (MIM) synthesized by aqueous suspension polymerization was applied as a selective sorbent of miniaturized matrix solid-phase dispersion combining with dispersive liquid-liquid microextraction (MSPD-DLLME) for the simultaneous determination of four Sudans in egg yolk samples. The solid sample was directly blended with MIM in MSPD procedure and the eluent of MSPD was used as the dispersive solvent of the followed DLLME for further purification and enrichment of the analytes before HPLC analysis. Good linearity for all the Sudan dyes was ranged from 0.02 μg g(-1) to 2.0 μg g(-1) (r(2)≥0.9990) and their recoveries at three spiked levels were ranged from 87.2% to 103.5% with RSD less than 6.1% (n=3). The presented MIM-MSPD-DLLME method combined the advantages of MIM, MSPD and DLLME, and could be applied for the determination of Sudans in complicated food samples.     

Selective solid-phase extraction of bisphenol A using molecularly imprinted polymers and its application to biological and environmental samples

Molecularly imprinted polymers (MIPs) were prepared using bisphenol A (BPA) as a template by precipitation polymerization. The polymer that had the highest binding selectivity and ability was used as solid-phase extraction (SPE) sorbents for direct extraction of BPA from different biological and environmental samples (human serum, pig urine, tap water and shrimp). The extraction protocol was optimized and the optimum conditions were as follows: conditioning with 5 mL methanol–acetic acid (3:1), 5 mL methanol, 5 mL acetonitrile and 5 mL water, respectively, loading with 5 mL aqueous samples, washing with 1 mL acetonitrile, and eluting with 3 mL methanol. MIPs can selectively recognize, effectively trap and preconcentrate BPA over a concentration range of 2–20 μM. Recoveries ranged from 94.03 to 105.3 %, with a relative standard deviation lower than 7.9 %. Under the optimal condition, molecularly imprinted SPE recoveries of spiked human serum, pig urine, tap water and shrimp were 65.80, 82.32, 76.00 and 75.97 %, respectively, when aqueous samples were applied directly. Compared with C18 SPE, a better baseline, better high-performance liquid chromatography separation efficiency and higher recoveries were achieved after molecularly imprinted SPE.