甲烷催化燃烧中制备参数对NiO/CuO-ZrO2催化剂高温反应性能的影响

采用溶胶凝胶－超临界干燥的方法制备了NiO/CuO-ZrO2催化剂，分别考察了焙烧温度、活性组分含量对催化剂甲烷燃烧性能的影响，并利用XRD、物理吸附等手段考察了两个参数对催化剂性能影响的本质原因，发现NiO/CuO-ZrO2催化剂具有较高的催化活性，较好的高温（1 000 ℃）反应稳定性，焙烧温度对催化剂的影响很大，500 ℃是合适的焙烧温度，通过试验发现活性组分NiO为5 mol％时催化剂适于在相对较低的温度下使用，而NiO为15 mol％时，催化剂具有较好的高温稳定性。     

甲醇与乙醇一步合成异丁醛用CuO-ZnO/Al2O3催化剂

在ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３催化剂上，甲醇与乙醇在常压和２１０￣３６０℃温度下一步反应合成异丁醛。利用正交设计方法，研究了ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３体系催化剂组成和制备条件等因素对催化剂催化性能的影响。结果表明，催化剂中ＣｕＯ含量对催化剂的催化活性影响最大，而ＺｎＯ含量则主要影响催化剂对异丁醛的选择性。催化剂制备条件，如沉淀温度、陈化时间等，也不同程度也影响催化剂的催化性能。ＸＲＤ和ＢＥＴ表征结果     

Cr/MgO催化剂上乙腈和甲醇选择性合成丙烯腈的研究

用浸渍法制备了系列MgO负载过渡金属氧化物催化剂，比较了这些催化剂的催化性能，详细考察了Cr／MgO催化剂的活性组份含量、焙烧温度及反应温度等因素对乙腈和甲醇选择性合成丙烯腈的影响。结果表明，对于Cr／MgO催化剂，当负载量3％时催化性能最佳，过高的负载量对生成丙烯腈的选择性影响不大，但乙腈转化率呈下降趋势，焙烧温度对生成丙烯腈选择性的影响不大，但经600℃焙烧的催化剂乙腈转化率最高，随着反应温度提高，乙腈转化率提高，而生成丙烯腈选择性400℃左右出现最高值，CO2-TPD表明，催化剂强吸附碱中心越多，越有利于乙腈和甲醇选择性合成丙烯腈反应，Cr／MgO催化剂中引入Na2O后，提高了乙腈的转化率，而生成丙烯腈的选择性降低。     

焙烧温度对合成低碳醇用Cu/Mn/Ni/ZrO2催化剂性能的影响

 研究了焙烧温度对合成低碳醇用Cu／Mn／Ni／ZrO2催化剂结构及催化性能的影响．随着焙烧温度的升高，催化剂的催化活性和产物分布都发生较大的变化．催化剂在较低的温度下焙烧，低温下反应液相产物的分布符合S－F方程；反应温度升高时，液相产物中主要是甲醇和异丁醇；在高温下焙烧的催化剂，其催化活性较低，但即使在较低的反应温度下，异丁醇在液相高级醇（C2＋OH）中也是主要的产物．结合其他的一些反应结果与XRD，BET，TPR及EXAFS等表征结果，认为焙烧温度使催化剂的结构发生了较大的变化，进而影响催化剂各组分之间的相互作用，从而使催化剂对合成低碳醇反应表现出不同的催化性能．     

B2O3/TiO2-ZrO2催化环己酮肟气相Beckmann重排反应研究Ⅱ.焙烧温度的影响

采用XRD、FT-IR和NH3-TPD等方法，研究了载体预焙烧温度和催化剂活化焙烧温度对B2O3/TIO2-ZRO2催化剂的结构、酸性和催化环己酮肟气相Beckmann重排反应性能的影响。结果表明，在383-773K范围内，载体预烧温度对催化剂性能的影响不大，但经973K高温预焙烧后，由于生成了ZrTiO4晶相，使其与H3BO3的相互作用减弱，从而导致催化剂的酸性和反应性能降低，提高催化剂活化焙烧温度，有利于B2O3与TiO2-ZrO2的相互作用，生成更多的Beckmann重排反应所需的中等强度酸中心，使催化剂的活性和选择性提高；但活化焙烧温度过高，会使催化剂中大量的B2O3晶粒析出，引起酸中心数量和催化活性的明显下降。     

水蒸汽对负载型催化剂丙烷脱氢性能的影响：Ⅰ.反应性能的研究

研究了ＭｇＡｌ２Ｏ４，ＺｎＡｌ２Ｏ４负载的Ｐｔ－Ｓｎ催化剂在氮气及水蒸汽中的丙烷脱氢性能。考察了还原温度，反应温度，催化剂载量对Ｐｔ－ＳＳｎ／ＭｇＡｌ２Ｏ４催化剂丙烷脱氢性能的影响。     

镍基气凝胶催化CH4-CO2重整制取合成气反应的研究 Ⅲ.影响催化剂积碳性能因素的探讨

考察了823K焙烧的干凝胶xNCA550、气凝胶aNCA550及浸渍型催化剂iNCA550在923K、1073K、1173K反应温度下的积碳行为，对催化剂表面碳的活性及类型进行了分析，并探讨了影响催化剂积碳的因素。实验结果表明，随反应温度的提高，催化剂的积碳能力减弱，尤以气凝胶催化剂aNCA550明显。催化剂的积碳主要发生在反应的初期，反应温度越高，到达积碳量相对稳定期所需要的时间越短；随着反应时间的延续，催化剂积碳量缓慢增长，并且表面碳的活性降低。催化剂的酸性和镍晶粒大小是影响其积碳性能的主要内在因素，而它们对积碳的影响程度受反应温度的影响，反应温度越高，催化剂表达酸性中心利于积碳的作用越小，小晶粒镍抑制催化剂积碳的能力越强。     

载体焙烧温度对Co／ZrO2催化剂催化F－T合成反应的影响

 采用并流共沉淀法制得了ZrO2载体，采用等体积浸渍法制备了钴质量分数为10％的系列负载型催化剂，考察了载体焙烧温度对催化剂催化性能的影响．结果表明，焙烧温度对载体的物化性质有显著影响，提高焙烧温度可降低载体的表面酸性，减弱钴锆之间的相互作用，提高催化剂的活性和选择性．钴负载到低温焙烧的载体上促进了ZrO2由无定形向四方相的转变，提高了催化剂的分散度，降低了催化剂的活性和选择性．     

阴极电泳涂料的制备及MEQ值的测定

采用封闭的甲苯二异氰酸酯作为固化剂合成了环氧树脂阴极电泳涂料,讨论了基料树脂的合成条件,最终确定了合成树脂的反应条件为:温度80℃,反应时间为2h,并采用了简便的方法测定了槽液的MEQ值,在150v下电泳3min,得到外观平整,综合性能优良的漆膜.     

负载型钌/铝钛复合载体上的二氧化碳甲烷化反应

用浸渍法制备了铝钛复合载体担载的钌催化剂，考察了它们对二氧化碳甲烷化反应的催化性能，结果表明，高TiO2含量载体制备的催化剂的活性和选择性较高，同时考察了反应温度、空速、金属担载量以及添加第二金属组分等对催化剂性能的影响．     

An investigation on the influence of a vinyl pyrrolidone/vinyl acetate copolymer on the moisture permeation, mechanical and adhesive properties of aqueous-based hydroxypropyl methylcellulose film coatings

Polymers for aqueous film coating, such as hydroxypropyl methylcellulose (HPMC), often require the inclusion of a plasticizer to reduce brittleness and increase flexibility and ductility. A vinyl pyrrolidone/vinyl acetate copolymer (S630) was investigated for its influence on HPMC film coating parameters, comparing the results with a commonly used plasticizer, polyethylene glycol and another copolymer, polyvinyl alcohol. The viscous properties of the solutions and the glass transition temperatures of the equivalent polymer films were evaluated. Its effect on the film properties, such as appearance, surface roughness, moisture permeation and mechanical properties, as well as its ability to promote better adhesion of the film coat to the core surface, was compared. S630 was able to reduce the viscosity of the polymer solution and glass transition temperature of HPMC, as well as, enhance the mechanical properties of the cast film. The moisture permeation was slightly reduced but not to the same extent as polyethylene glycol. A 10% concentration of S630 increased the adhesive strength and toughness of the HPMC film coat. In conclusion, S630 was effective as a film-former, substrate adhesive and plasticizer. It has the potential to be used to replace the more volatile plasticizers which have problems of loss or migration.     

Admicellar polymerization of styrene on cotton

Thin-film coating on cotton by the admicellar polymerization process was investigated. In this work, styrene was used as the monomer to coat styrene on cotton. The effects of surfactant, styrene, initiator, and electrolyte concentrations on the polymerization process were determined. The polystyrene film formed was characterized by SEM, FTIR, and GPC. The increase in the hydrophobicity of the treated cotton surface was determined by the drop test. Results show that polystyrene thin film was successfully formed on cotton, resulting in cotton that can resist wetting by a water droplet for longer than 30 min.     

Surface precipitation of highly porous hydrotalcite-like film on Al from a zinc aqueous solution

A hydrotalcite-like film has been successfully deposited on an Al-bearing glass substrate based on an interface reaction between an Al layer and a zinc aqueous solution. The film selectively grew on the Al surface but not on the glass surface. The film on Al was composed of layered nanosheets of a hydrotalcite-like compound containing Al and Zn. Comparably, deposits on the plastic surface and precipitates in solution were wurzite-type ZnO with various morphologies depending upon the preparation conditions. At low supersaturation degrees, single crystals and superstructures of Zn-Al hydrotalcite were also obtained. This porous hydrotalcite film has a potential application as catalyst supports, environmental materials, or matrixes for hydrotalcite-based nanocomposite films. Using Al as a reaction interface makes it easy to coat porous hydrotalcites on a series of matrix materials varying in shapes and properties, which is important for achieving practical applications. In addition, the method developed should be widely applicable to other systems for the preparation of porous or oriented hydrotalcite-like thin films by an appropriate combination of divalent/trivalent solution-substrate systems.     

Dosimetry characteristics of the nitro blue tetrazolium-polyvinylalcohol film for high dose applications

The dosimetry characteristics of a polyvinylalcohol based radiochromic dye film containing the ditetrazolium salt nitro blue tetrazolium chloride were studied with respect to the potential use of the films for routine dosimetry in radiation processing. The useful dose range for the dosimeter film for gamma and electron irradiation is 5–50 kGy depending on the concentration of the dye. The effects of irradiation temperature and humidity, as well as the stability of the response of the film before and after irradiation, were investigated and determined. Formulations for preparation of the films with different concentrations of the dye and with different pH were tested. The films were also tested in industrial gamma irradiation facilities for process control purposes by comparing their performance with transfer standard dosimeters.     

8-羟基喹啉铝高分子薄膜的荧光特性

1前言许多的有机化合物在外界条件激发下发出可见光区的荧光,且具有很高的荧光率,如环状化合物及一些具有共轭键的链状化合物等．基于这一特性,许多有机材料成为彩色、大屏幕显示器件等方面应用的理想材料．8一羟基喷淋铝Alq。是这类有机材料中的一种．有关Alq。的文献,虽然对其特性有各种各样的研究t’‘”,然而却没有发现有关Alq。在高分子膜中荧光特性的报导．本文报导了A冲在不同的高分子材料膜中的荧光特性并探讨了各种影响因素,为A你在光学微腔结构的进一步应用提供了一些依据．8一羟基咦淋曾被用在对一些金属离子的分析检测…     

基片温度对LiCoO2薄膜结构与电化学性能的影响

采用射频(RF)磁控溅射技术制备了用于全固态薄膜锂电池的非晶态和多晶LiCoO2阴极薄膜,利用XRD和SEM研究了沉积温度对LiCoO2薄膜结构和形貌的影响,并研究了高温退火后薄膜的电化学性能.研究结果表明,随著基片温度的不同,薄膜成分、表面形貌以及电化学行为有明显差异.室温沉积的薄膜很难消除薄膜中Li2CO3的影响,经过高温退火处理后也无法形成有效的多晶LiCoO2薄膜,而150℃沉积的薄膜经过高温退火后形成了有利于锂离子嵌入的多晶LiCoO2结构,薄膜显示出了较好的电化学性能.     

Tetraethylorthosilicate film modified with protein to fabricate cholesterol biosensor

Sol-gel derived tetraethylorthosilicate (TEOS) films were prepared by spin coating method on indium tin oxide (ITO) coated glass plate. Hydrophobic interaction method was used to coat the bovine serum albumin film over the surface of tetraethylorthosilicate sol-gel film to minimize cracking, biofouling and to improve the stability of the film. Cholesterol oxidase (ChOx) and horseradish peroxidase (HRP) were immobilized using covalent linkage with bovine albumin serum film to enhance the loading of the enzyme to improve the sensitivity of biosensor. Further ITO-TEOS-BSA-ChOx/HRP film was characterized by UV-vis, FTIR and SEM techniques. The optical response of the ITO-TEOS-BSA-ChOx/HRP biosensor was found to be linear in the range of 2-8 mM for cholesterol concentration with response time approximately 20 s. Amperometric response of ITO-TEOS-BSA-ChOx/HRP was observed to be linear in the range of 2-12 mM of cholesterol concentration with 10-s response time. Michaelis-Menten constant was calculated 21.2 mM .The shelf life of ITO-TEOS-BSA-ChOx/HRP biosensor was approximately about 8 weeks in desiccated conditions at room temperature.     

8-羟基喹啉铝高分子薄膜的荧光特性

In this paper, the solid state. polymer thin films of 8-hydroxylquinoline aluminum (Alq3) were made by spinning coat method. The fluorescence efficiencies and the luminescence spectra of them were measured via the laser systems. Various experimental factors were considered and tested. It was found that the peak wavelength of the luminescence spectra of the Alq3 polymer films shifted and that the purity of the samples affected its fluorescence efficiencies: the fluorescence efficiencies of impure samples were about three-fourth of that of the purified ones; fluorescence efficiencies of Alq3 doped in PMMA polymer was higher than that doped in PC and PEO. Under certain conditions, transparent thin film 10 layers can be achieved. This kind of polymer thin film of Alq3 exhibits well fluorescence response, but also has good stability. Spin coat method can greatly reduce the technical requirements comparing with the vacuum plating method.     

Vapor phase polymerization of 3,4‐ethylenedioxythiophene on flexible substrate and its application on heat generation

An oxidative chemical vapor phase polymerization process is applied to coat flexible polyethylene terephthalate (PET) fabrics with a uniform poly(3,4‐ethylenedioxythiophene) (PEDOT) film. This vapor phase polymerization method is a solventfree technique, which could yield a low resistance in the PEDOT‐coated PET fabric. The resistance as low as 52 Ω square^?1 is achieved. The polymerization conditions, such as the concentration of oxidant, reaction time, and temperature, have been systematically investigated. The coated fabric samples exhibit an increase in temperature when subjected to a fixed DC voltage. This result indicates a potential application of these PEDOT‐coated fabrics as electric heating materials. Copyright © 2009 John Wiley & Sons, Ltd.     

Surface Treatment of Dimenhydrinate Crystals

Dimenhydrinate is a heat-sensitive antihistamine with a low melting point. The heat-sensitive feature is of importance if direct compression is used. Direct measurement of the heat originating in the texture of tablets during compression is very difficult. Thermoanalytical methods were used as indirect methods to describe the changes in material properties at high temperature: differential scanning calorimetry, thermomicroscopy and thermogravimetric analysis. Film coating method is widely used in pharmaceutical technology. A fluidized bed apparatus was applied to coat the crystals. The coating film forming agent was hydroxy-propyl-methylcellulose (HPMC), which is a gastric-soluble polymer. Thermoanalytical measurements reveal that dimenhydrinate crystals are sensitive to heat. Film coating method does not alter the shape of the DSC curve of dimenhydrinate, but increases the melting point. The presence of a macromolecular film reduces the thermal conductivity, because it separates the particles. This revised version was published online in August 2006 with corrections to the Cover Date.