Structure and properties of aqueous dispersions of sodium dodecyl sulfate with carbon nanotubes

The dispersing action of the surfactant (sodium dodecyl sulfate, SDS) on the carbon nanotubes (CNT) in aqueous medium has been studied. Electron microscopy, molecular docking, NMR and IR spectroscopies were applied to determine the physical-chemical properties of CNT dispersions in SDS—water solutions. It was established that micellar adsorption of the surfactant on the surface of carbon material and solubilization of SDS in aqueous medium contribute to improving CNT dispersing in water solutions. It was shown that the non-polar hydrocarbon radicals of a single surfactant molecule form the highest possible number of contacts with the graphene surface. Upon increase of the SDS in solution these radicals form micelles connected with the surface of the nanotubes. At the sufficiently high SDS concentration the nanotube surface becomes covered with an adsorbed layer of surfactant micelles. Water molecules and sodium cations are concentrated in spaces between micelles. The observed pattern of micellar adsorption is somewhat similar to a loose bilayer of surfactant molecules.     

Influence of the polyelectrolyte poly(ethyleneimine) on the adsorption of surfactant mixtures of sodium dodecyl sulfate and monododecyl hexaethylene glycol at the air-solution interface

The polyelectrolyte poly(ethylenenimine), PEI, is shown to strongly influence the adsorption of the anionic-nonionic surfactant mixture of sodium dodecyl sulfate, SDS, and monododecyl hexaethylene glycol, C(12)E(6), at the air-solution interface. In the presence of PEI, the partitioning of the mixed surfactants to the interface is highly pH-dependent. The adsorption is more strongly biased to the SDS as the pH increases, as the PEI becomes a weaker polyelectrolyte. At surfactant concentrations >10(-4) M, the strong interaction and adsorption result in multilayer formation at the interface, and this covers a more extensive range of surfactant concentrations at higher pH values. The results are consistent with a strong interaction between SDS and PEI at the surface that is not predominantly electrostatic in origin. It provides an attractive route to selectively manipulate the adsorption and composition of surfactant mixtures at interfaces.     

Suppression of surfactant interferences in anodic stripping voltammetry by sodium dodecyl sulfate

It was investigated whether interferences from surfactants in anodic stripping voltammetry (ASV) could be remedied by the anionic surfactant sodium dodecyl sulfate (SDS) which causes little or no interference in itself. Cadmium and lead were used as test analytes, and measurements were performed in acetate buffer as well as in 0.1 M HNO₃. One hundred parts per million of the interfering surfactant was added. SDS eliminated severe interference from the non-ionic surfactants Triton^© X-100 and dodecyl octaethylene glycol ether as well as from the polymer polyethylene glycol 6000 and from the cationic surfactant cetyl trimethyl ammonium bromide. SDS could not remedy the extraordinarily severe interference from the cationic surfactant cetyl pyridinium chloride. Two anionic surfactants were also tested as interferents but they had little detrimental effect on the ASV signals. The effect of SDS was explained by the formation of mixed micelles which scavenge the interferent in the bulk solution and by competitive displacement of the interferent at the electrode surface.     

Effects of anionic surfactants on ligand-promoted dissolution of iron and aluminum hydroxides

We investigated the influence of the surfactants sodium dodecyl sulfate (SDS) and rhamnolipid (RhL) on ligand-promoted dissolution of goethite (alpha-FeOOH) and boehmite (gamma-AlOOH) at pH 6. The siderophore desferrioxamine B (DFOB), its derivate desferrioxamine D (DFOD), ethylenediaminetetraacetic acid (EDTA), and 8-hydroxyquinoline-5-sulfonic acid (HQS) were used as ligands. The rates of ligand-promoted dissolution of goethite were significantly increased in the presence of low concentrations of anionic surfactants (<80 microM SDS; <6 mg/L RhL). At higher surfactant concentrations, however, the effects of surfactants were negligible. The dissolution rates in the presence of surfactants were not correlated with adsorbed amounts of ligands. Three possible factors contributing to these observations were further investigated and discussed: (i) adsorbed surfactants may influence ligand adsorption by changes in the ligand's surface speciation, (ii) re-adsorption of Fe-DFOB or Fe-DFOD complexes may lead to an underestimation of siderophore-promoted dissolution rates at high surfactant concentrations, and (iii) co-adsorption of protons to goethite with SDS may influence the dissolution rates. However, our results show that none of these three factors can satisfactorily explain the observed effects of anionic surfactants on ligand-promoted dissolution rates of iron and aluminum hydroxides.     

Anomalous solubilization behavior of dimyristoylphosphatidylcholine liposomes induced by sodium dodecyl sulfate micelles

The solubilization dynamics of dimyristoylphosphatidylcholine (DMPC) liposomes, as induced by sodium dodecyl sulfate (SDS), were investigated; this investigation was motivated by several types of atypical behavior that were observed in the solubilization in this system. The liposomes and surfactants were mixed in a microchip, and the solubilization reaction of each liposome was observed using a microscope. We found that solubilization occurred not only via a uniform dissolution of the liposome membrane, but also via a dissolution involving the rapid motion of the liposome, or via active emission of protrusions from the liposome surface. We statistically analyzed the distribution of these patterns and considered hypotheses accounting for the solubilization mechanism based on the results. When the SDS concentration was lower than the critical micelle concentration (CMC), the SDS monomers entered the liposome membrane, and mixed micelles were emitted. When the SDS concentration was higher than the CMC, the SDS micelles directly attacked the liposome membrane, and many SDS molecules were taken up; this caused instability, and atypical solubilization patterns were triggered. The size dependence of the solubilization patterns was also investigated. When the particle size was smaller, the SDS molecules were found to be homogeneously dispersed throughout the whole membrane, which dissolved uniformly. In contrast, when the particle size was larger, the density of SDS molecules increased locally, instability was induced, and atypical dissolution patterns were often observed.     

Synergistic sphere-to-rod micelle transition in mixed solutions of sodium dodecyl sulfate and cocoamidopropyl betaine

Static and dynamic light scattering experiments show that the mixed micelles of sodium dodecyl sulfate (SDS) and cocoamidopropyl betaine (CAPB) undergo a sphere-to-rod transition at unexpectedly low total surfactant concentrations, about 10 mM. The lowest transition concentration is observed at molar fraction 0.8 of CAPB in the surfactant mixture. The transition brings about a sharp increase in the viscosity of the respective surfactant solutions due to the growth of rodlike micelles. Parallel experiments with mixed solutions of CAPB and sodium laureth sulfate (sodium dodecyl-trioxyethylene sulfate, SDP3S) showed that the sphere-to-rod transition in SDP3S/CAPB mixtures occurs at higher surfactant concentrations, above 40 mM. The observed difference in the transition concentrations for SDS and SDP3S can be explained by the bulkier SDP3S headgroup. The latter should lead to larger mean area per molecule in the micelles containing SDP3S and, hence, to smaller spontaneous radius of curvature of the micelles (i.e., less favored transition from spherical to rodlike micelles). The static light scattering data are used to determine the mean aggregation number and the effective size of the spherical mixed SDS/CAPB micelles. From the dependence of the aggregation number on the surfactant concentration, the mean energy for transfer of a surfactant molecule from a spherical into a rodlike micelle is estimated.     

Micelles in mixtures of sodium dodecyl sulfate and a bolaform surfactant

Mixtures composed of water, sodium dodecyl sulfate (SDS), and a bolaform surfactant with two aza-crown ethers as polar headgroups (termed Bola C-16) were investigated by modulating the mole ratios between the components. The two surfactants have ionic and nonionic, but ionizable, headgroups, respectively. The ionization is due to the complexation of alkali ions by the aza-crown ether unit(s). Structural, thermodynamic, and transport properties of the above mixtures were investigated. Results from surface tension, translational self-diffusion, and small angle neutron scattering (SANS) are reported and discussed. Interactions between the two surfactants to form mixed micelles result in a combination of electrostatic and hydrophobic contributions. These effects are reflected in the size and shape of the aggregates as well as in transport properties. The translational diffusion of the components in mixed micelles, in particular, depends on the Bola C-16/SDS mole ratio. Nonideality of mixing of the two components was inferred from the dependence of the critical micelle concentration, cmc, on the mole fraction of Bola C-16. This behavior is also reflected in surface adsorption and in the area per polar headgroup at the air-water interface. SANS data analysis for the pure components gives results in good agreement with previous findings. An analysis of data relative to mixed systems allows us to compute some structural parameters of the mixed aggregates. The dependence of aggregation numbers, nu(T), on the Bola C-16/SDS mole ratio displays a maximum that depends on the overall surfactant content and is rationalized in terms of the nonideality of mixing. Aggregates grow perpendicularly to the major rotation axis, as formerly observed in the Bola C-16 system, and become progressively ellipsoidal in shape.     

Mucin-chitosan complexes at the solid-liquid interface: multilayer formation and stability in surfactant solutions

The adsorption of a biologically important glycoprotein, mucin, and mucin-chitosan complex layer formation on negatively charged surfaces, silica and mica, have been investigated employing ellipsometry, the interferometric surface apparatus, and atomic force microscopy techniques. Particular attention has been paid to the effect of an anionic surfactant sodium, dodecyl sulfate (SDS), with respect to the stability of the adsorption layers. It has been shown that mucin adsorbs on negatively charged surfaces to form highly hydrated layers. Such mucin layers readily associate with surfactants and are easily removed from the surfaces by rinsing with solutions of SDS at concentrations > or =0.2 cmc (1 cmc SDS in 30 mM NaCl is equal to 3.3 mM). The mucin adsorption layer is negatively charged, and we show how a positively charged polyelectrolyte, chitosan, associates with the preadsorbed mucin to form mucin-chitosan complexes that resist desorption by SDS even at SDS concentrations as high as 1 cmc. Thus, a method of mucin layer protection against removal by surfactants is offered. Further, we show how mucin-chitosan multilayers can be formed.     

Complexation between dodecyl sulfate surfactant and zein protein in solution

Interactions between sodium dodecyl sulfate and zein protein, a model system for the understanding of the effect of surfactants on skin, were investigated using a range of techniques involving UV-vis spectroscopy, TOC (total organic carbon analysis), electrophoresis, and static and dynamic light scattering. Zein protein was solubilized by SDS. The adsorption of SDS onto insoluble protein fraction caused the zeta potential of the complex to become more negative. From these values, we calculated the Gibbs energy of absorption, which decreases when the SDS concentration is raised. Finally the structure of the complex, based on the analysis by static and dynamic light scattering, is proposed to be rod like.     

New thermodynamic/electrostatic models of adsorption and tension equilibria of aqueous ionic surfactant mixtures: application to sodium dodecyl sulfate/sodium dodecyl sulfonate systems

The nonideal adsorbed solution (NAS) theory has been formally extended to adsorption at the air/water interface from aqueous mixtures of ionic surfactants, explicitly accounting for the surface potential of the adsorbed monolayer with the Gouy-Chapman theory. This new ionic NAS (iNAS) theory is thermodynamically consistent and, when coupled to a micellization model, is valid for concentrations below and above the mixed cmc. Counterion binding is incorporated into the model using two fractional binding parameters, beta(sigma) for the adsorbed monolayer and beta(m) for the micelles. The regular solution theory is used to model the nonideal interactions within the adsorbed monolayer and within the mixed micelles. New tension data for an equimolar mixture of sodium dodecyl sulfate (SDS) and sodium dodecyl sulfonate (SDSn) at two salinities fit this model well when mixing is ideal. The total surface densities, the surface compositions, and the surface potentials for the mixed monolayers are calculated. When there is no added salt, at total surfactant concentrations below the mixed cmc, the adsorbed monolayer is enriched in SDSn, but at total concentrations at and above the mixed cmc, the adsorbed monolayer is nearly an equimolar mixture. In the presence of 100 mM NaCl, the adsorbed monolayer is nearly an equimolar mixture, independent of the total surfactant concentration.     

Complexation between sodium dodecyl sulfate and amphoteric polyurethane nanoparticles

The complexation between negatively charged sodium dodecyl sulfate (SDS) and positively charged amphoteric polyurethane (APU) self-assembled nanoparticles (NPs) containing nonionic hydrophobic segments is studied by dynamic light scattering, pyrene fluorescent probing, zeta-potential, and transmission electron microscopy (TEM) in the present paper. With increasing the mol ratio of SDS to the positive charges on the surface of APU NPs, the aqueous solution of APU NPs presents precipitation at pH 2, around stoichiometric SDS concentration, and then the precipitate dissociates with excess SDS to form more stable nanoparticles of ionomer complexes. Three stages of the complexation process are clearly shown by the pyrene I1/I3 variation of the complex systems, which only depends on the ratio of SDS/APU, and demonstrate that the process is dominated by electrostatic attraction and hydrophobic aggregation.     

The effects of the addition of the polyelectrolyte, poly(ethyleneimine), on the adsorption of mixed surfactants of sodium dodecylsulfate and dodecyldimethylaminoacetate at the air-water interface

The effects of the addition of the polyelectrolyte, poly(ethyleneimine), PEI, on the adsorption of the mixed surfactants of sodium dodecylsulfate, SDS, and dodecyldimethylaminoacetate, dodecyl betaine, at the air-water interface have been investigated using neutron reflectivity and surface tension. In the absence of PEI the SDS and dodecyl betaine surfactants strongly interact and exhibit synergistic adsorption at the air-water interface. The addition of PEI, at pH 7 and 10, results in a significant modification of the surface partitioning of the SDS/dodecyl betaine mixture. The strong surface interaction at high pH (pH 7 and 10) between the PEI and SDS dominates the surface behavior. For solution compositions in the range 20/80-80/20 mol ratio dodecyl betaine/SDS at pH 7 the surface composition is strongly biased towards the SDS. At pH 10 a similar behavior is observed for a solution composition of 50/50 mol ratio dodecyl betaine/SDS. This strong partitioning in favor of the SDS at high pH is attributed to the strong ion-dipole attraction between the SDS sulfate and the PEI imine groups. At pH 3, where the electrostatic interactions between the surfactant and the PEI are dominant, the dodecyl betaine more effectively competes with the SDS for the interface, and the surface composition is much closer to the solution composition.     

Miscibility of sodium dodecyl sulfate and sodium decyl sulfate in the adsorbed film and micelle

The interfacial tension of the aqueous solution of sodium dodecyl sulfate (SDS) and sodium decyl sulfate (SDeS) mixture against hexane was measured as a function of the total molality and composition of the surfactant mixture at 298.15 K under atmospheric pressure. The compositions of adsorbed film and micelle were evaluated numerically by applying the thermodynamic relations to the experimental results. These results were shown in the form of the phase diagrams of adsorption and micelle formation and compared with those of the aqueous solution of sodium perfluorooctanoate (SPFO) and SDeS mixture. It was found that the diagrams of SDS and SDeS system have swollen cigar shapes and are quite different from those of SPFO and SDeS system which show non-ideal mixing both in the adsorbed film and micelle. This finding was attributed to the fact that the interaction between fluorocarbon and hydrocarbon chains is weaker than that between hydrocarbon chains.     

Heat of adsorption of surfactants and its role on nanoparticle stabilization

In this work, the binding between sodium oleate (SO), sodium laurate (SL), sodium dodecyl sulfate (SDS), and sodium dodecylphosphonate (SDP) and iron oxide nanoparticles was systematically investigated using isothermal titration calorimetry (ITC). Comparing the heat exchanged during the isothermal titration with the corresponding surfactant adsorption isotherm, in the cases of SO and SDP, a strong binding takes place at low surfactant concentrations. The binding enthalpy at this low surfactant concentrations depends on the type of surfactant anionic head group. For C12 surfactants, the phosphonate group produced the strongest endothermic binding, followed by the exothermic binding with the carboxylate group, followed by weak exothermic interaction with the sulfate group. For carboxylate surfactants, longer surfactant tails result in larger exothermic binding. Surfactants that exhibited large binding enthalpies also produced more stable suspensions. The Langmuir (L), Freundlich (F), and Langmuir–Freundlich (L–F) adsorption models were used to interpret the adsorption isotherms during the titration with sodium oleate. The L–F adsorption isotherm model was selected to calculate the heat of the formation of the SO monolayer and bilayer on the iron oxide nanoparticles. The L–F model reflects the finite or limited adsorption of the Langmuir model, but accounts for non-homogeneous adsorption of the Freundlich model that help account for surfactant self-assembly before and after adsorption. Coupling the adsorption model with the titration data is possible to calculate the real heat of adsorption of the surfactants on the metal oxide.     

Effects of addition of short-chain alcohol solvents on micellization and thermodynamic properties of anionic surfactants sodium dodecyl sulfate and sodium dodecyl sulfonate in aqueous solutions

Micellar and thermodynamic properties of anionic surfactants sodium dodecyl sulfate (SDS) and sodium dodecyl sulfonate (SDSn) in aqueous solutions of 5 wt% short-chain alcohols methanol, ethanol, and 1-butanol were investigated by experimental electrical conductivities, densities and sound velocities at 298.15 K. It was found that methanol behaves like a cosolvent and increases the critical micelle concentration (CMC) of both surfactants in aqueous solutions. However, the other investigated alkanols act as a cosurfactant and decrease the CMC by their presence. The values of the degree of counterion association on the micelles of both surfactants in aqueous methanol solution are same as those in pure water, and they decrease with increasing the alkyl chain length of alcohol. Furthermore, the values of the apparent molar volume and isentropic compressibility of the monomeric and micellar forms of the investigated surfactants were obtained from the experimental density and sound velocity data. It was found that the values of the apparent molar properties of both micellar and monomeric forms of the studied surfactants increase by increasing the alkyl chain of the alcohols.     

Effect of sodium dodecyl sulfate on dynamic surface properties of lysozyme solutions

The surface dilatation rheological properties of lysozyme/sodium dodecyl sulfate (SDS) mixed solutions are studied by the oscillating ring method. At the initial stage of adsorption, the rate of variations in the surface properties depends nonmonotonically on SDS concentration due to the reversal of the lysozyme/SDS complex charge with increasing degree of surfactant binding. The nonmonotonic kinetic dependences of the dynamic surface elasticity indicate the breakage of the secondary and tertiary structures of the protein in the surface layer. For lysozyme/SDS solutions, the denaturing effect of the interface appears to be stronger than for previously studied systems, namely, bovine serum albumin/dodecyltrimethylammonium bromide and β-lactoglobulin/dodecyltrimethylammonium bromide.     

Effect of sodium dodecyl sulfate and cetyltrimethylammonium bromide catanionic surfactant on the enzymatic hydrolysis of Avicel and corn stover

Nonionic surfactants could effectively improve the enzymatic hydrolysis efficiency of lignocellulose, while small molecule anionic and cationic surfactants usually inhibited the enzymatic hydrolysis. The results showed that the anionic surfactant sodium dodecyl sulfate (SDS) could improve the enzymatic hydrolysis efficiency of Avicel at the concentration range of 0.1–1 mM, but it did inhibit enzymatic hydrolysis at higher concentration. Cationic surfactant cetyltrimethylammonium bromide (CTAB) was used to regulate the surface charge of SDS; thereby catanionic surfactant SDS-CTAB was formed. The effect of SDS-CTAB catanionic surfactant with varied molar ratios on the enzymatic hydrolysis of pure cellulose and corn stover at various enzymatic hydrolysis environments was investigated. SDS-CTAB could increase the enzymatic hydrolysis of corn stover at high solid loading from 33.3 to 42.4%. Using SDS-CTAB could reduce about 58% of the cellulase dosage to achieve 80% of the enzymatic hydrolysis of corn stover. SDS-CTAB catanionic surfactant could regulate the surface charge of cellulase in the hydrolyzate and reduce the non-productive adsorption of cellulase on the lignin, thereby improving the enzymatic hydrolysis efficiency of lignocellulose.     

Interaction between poly(vinylimidazole) and sodium dodecyl sulfate: binding and adsorption properties at the silica/water interface

The adsorption properties (adsorbed amount, kinetics, and reversibility) of poly(vinylimidazole) (PVI) and sodium dodecyl sulfate from PVI/SDS mixed solutions on negatively charged silica substrates were studied at pH 9 using reflectometry and compared to that measured on colloidal silica by the solution depletion method. In this paper, we will try to gain insight into the effect of PVI/SDS complex composition on the adsorption characteristics of the complex and particularly on the kinetics of the complex adsorption and its consequence on the adsorption reversibility. The properties of the complex in solution were characterized by means of potentiometric titration at a constant pH, binding isotherm, and surface tension measurements. On the basis of the experimental results the prevailing mechanism of the SDS/PVI interaction and the properties of the PVI/SDS complex were evaluated. Both the PVI/SDS complex uptake and the kinetics of the adsorption decreased with the amount of SDS bound to PVI. At low PVI/SDS binding ([SDS](0)CAC) the incoming complex experiences a blocking barrier of an electrostatic nature. This barrier has been confirmed by reversibility measurement, and the respective roles of the complex structure and charge were assessed.     

Adsorption of poly(styrene sulfonate) of different molecular weights on alpha-alumina: effect of added sodium dodecyl sulfate

The adsorption of poly(styrene sulfonate), PSS, of different molecular weights (70,000, 500,000, and 1,000,000 mol/kg), from aqueous solutions on alpha-alumina has been investigated. PSS of the lower molecular weight adsorbs less than the others whose adsorption isotherms overlap. The adsorption is found to increase with increasing ionic strength of the solutions indicating that both electrostatic and non-electrostatic contributions are involved in the adsorption process. Upon addition of the anionic surfactant, sodium dodecyl sulfate, SDS, PSS is found to adsorb less the more SDS added. SDS is found to be preferentially adsorbed as shown both from the simultaneous adsorption of the components and also from the sequential adsorption process where SDS in all cases displaces preadsorbed PSS from the solid surface. The displacement of preadsorbed polyelectrolyte by surfactant is a very slow process and the displacement is less pronounced as the molecular mass of the polyelectrolyte increases indicating the fewer number of contact points to the surface. This is further underlined by the effect on the displacement of PSS by SDS upon increasing the ionic strength of the solutions.     

Surfactant displacement of human serum albumin adsorbed on loosely packed self-assembled monolayers: cetyltrimethylammonium bromide versus sodium dodecyl sulfate

The surfactants sodium dodecyl sulfate (SDS) and cetyltrimethylammonium bromide (CTAB) displace human serum albumin (HSA) from loosely packed self-assembled monolayers (SAM) of hydrophobic alkyl chains by different means. Removal of HSA is of interest because previous work has suggested that the adsorption of HSA to such loosely packed SAMs may be sufficiently tenacious to offer opportunities for surface passivation. While HSA remains on the surface after exposure to SDS and rinsing, no protein remains after exposure to CTAB and rinsing. X-ray reflectivity and X-ray photoelectron spectroscopy measurements indicate that CTAB molecules remain interdigitated in the loosely packed SAM after rinsing, suggesting that CTAB is more effective in removing the HSA because it interacts more strongly with the SAM.