Ion-exchange separation and spectrophotometric determination of traces of gold

Summary A combined ion-exchange — spectrophotometric method has been developed for the separation and determination of traces of Au(III) in seven metal ions: Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Se(IV) and Cd(II). Au(III) is adsorbed selectively on a DEAE column from dilute chloride solution, while other metal ions pass through the column. Au(III) is recovered by elution with 1M hydrochloric acid. Traces of Au(III) in the effluent are determined by a new spectrophotometric method, which is based on the formation and extraction of Au(III) — azide — methylene blue complex. Separations of traces of Au(III) from 1000-fold of Pd(II) and Pt(IV) and 10000-fold of Hg(II) are also effected on a DEAE column in mixed methanol 1M hydrochloric acid medium (8 2). While Pd(II), Pt(IV) and Hg(II) are retained on the column, Au(III) adsorbs very weakly, so that the separations can be accomplished easily.

---

Zusammenfassung Eine mit Ionenaustausch kombinierte spektrophotometrische Methode zur Trennung und Bestimmung von Goldspuren neben sieben verschiedenen Metallionen wurde ausgearbeitet, nämlich neben Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Se(IV) und Cd(II). Das Gold wird an einer Säule aus Diäthylaminoäthylzellulose (DEAE) aus verdünnter Chloridlösung adsorbiert, wobei die anderen Metalle die Säule passieren. Durch Elution mit 1-m Salzsäure wird das Gold wieder gewonnen. Goldspuren im Effluenten werden mit Azid und Methylenblau komplex gebunden und so spektrophotometriert. Von der 1000fachen Menge Pd(II) und Pt(IV) sowie der 100000fachen Menge Hg(II) können Goldspuren auch aus Methanol + 1-m Salzsäure (12) mit einer DEAE-Säule abgetrennt werden. Während Pd(II), Pt(IV) und Hg(II) an der Säule festgehalten werden, wird Au(III) nur sehr schwach adsorbiert, so daß die Trennung leicht gelingt.

     

Dynamic ultrasound-assisted extraction of cadmium and lead from plants prior to electrothermal atomic absorption spectrometry

A dynamic ultrasound-assisted extraction step is proposed for the quantitative extraction of Cd and Pb from plant leaves prior to determination by electrothermal atomic absorption spectrometry (ETAAS). Beech leaves (a certified reference material—CRM 100—where the target analytes were not certified) were used for optimizing the extraction step by a multivariate approach. The samples (0.25 g) were subjected to dynamic ultrasound-assisted extraction with dilute nitric acid as extractant. The method was validated with a certified reference material BCR-062 (olive leaves) where both Cd and Pb are certified. The good agreement between the certified values and those found using the proposed method demonstrates its usefulness. The repeatability was 2.0 and 0.9% and the within-laboratory reproducibility was 7.1 and 2.8% for Cd and Pb, respectively. The precision of the method, together with its efficiency, rapidity, low cost and environmental acceptability makes it a good alternative for the determination of trace metals from plant material.     

On-line extraction of metal ions using liquid-liquid segmentation and a membrane type phase separator for fluorescence detection

Summary A liquid segmented post-column reaction system has been used to extract metal ions from an aqueous eluent into an organic solvent for fluorescence detection. The metals Zr(IV), Ga(III), Sc(III), Y(III), In(III), Al(III), La(III), Zn(II), Cd(II), Ca(II) and Mg(II) have been isocratically separated on a C₁₈ column by virtue of the secondary chemical equilibrium established by an eluent containing n-octanesulfonate, tartaric acid, and hydroxyisobutyric acid. The chelating reagent 8-hydroxyquinoline dissolved in methylisobutyl ketone (MIBK) was used to extract the metals and a membrane type phase separator was effective at separating the phases and directing the organic stream to the detector. The response for this detection approach was linear for metal ion concentrations spanning the range of the detector, and detection limits for most metals were low parts-per-billion (ppb). Band broadening for the extraction system was examined and compared to a direct post-column reaction using oxine dissolved in acetone.     

Comparison Studies on Several Ligands Used in Determination of Cd(II) in Rice by Flame Atomic Absorption Spectrometry after Ultrasound-Assisted Dispersive Liquid–Liquid Microextraction

Ligands plays an important role in the extraction procedures for the determination of cadmium in rice samples by using flame atomic absorption spectrometry (FAAS). In the present study, comparative evaluation of 10 commercially available ligands for formation of Cd(II)-ligand complex and determination of cadmium in rice samples by ultrasound-assisted dispersive liquid–liquid microextraction (UADLLME) combined with FAAS was developed. Sodium diethyldithiocarbamate (DDTC) provided a high distribution coefficient as well as a good absorbance signal, therefore DDTC was used as a ligand in UADLLME. A low density and less toxic solvent, 1-heptanol, was used as the extraction solvent and ethanol was used as the disperser solvent. In addition, the experimental conditions of UADLLME were optimized in standard solution first and then applied in rice, such as the type and volume of extractant and dispersant, pH, extraction time, and temperature. Under the optimal experimental conditions, the detection limit (3σ) was 0.69 μg/L for Cd(II). The proposed method was applied for the determination of Cd(II) in three different rice samples (polished rice, brown rice, and glutinous rice), the recovery test was carried out, and the results ranged between 96.7 to 113.6%. The proposed method has the advantages of simplicity, low cost, and accurate and was successfully applied to analyze Cd(II) in rice.     

Functionalization of cross linked chitosan with 2-aminopyridine-3-carboxylic acid for solid phase extraction of cadmium and zinc ions and their determination by atomic absorption spectrometry

We have developed a new method for solid phase extraction (SPE) and preconcentration of trace amounts of cadmium and zinc using cross linked chitosan that was functionalized with 2-aminopyridine-3-carboxy acid. Analytical parameters, sample pH, effect of flow rate, sample volume, and concentration of eluent on column SPE were investigated. The effect of matrix ions on the recovery of cadmium and zinc has been investigated and were found not to interfere with preconcentration. Under the optimum experimental conditions, the preconcentration factors for Cd(II) and Zn(II) were found to be 90. The two elements were quantified via atomic absorption spectrometry. The detection limits for cadmium and zinc are 21 and 65?ng?L^?1, respectively. The method was evaluated by analyzing a certified reference material (NIST 1643e; water) and has been successfully applied to the analysis of cadmium and zinc in environmental water samples.

Determination of Cadmium,Nickel, Lead,and Zinc in Fish Tissue by Flame and Graphite Furnace Atomic Absorption after Extraction with Pyrrolidine Dithiocarbamate and Activated Carbon

A solid phase extraction (SPE) technique using an activated carbon column was developed for the extraction of trace levels of Cd, Ni, Pb, and Zn in aqueous solution which was obtained from the digestion of fish tissue. Ammonium pyrrolidin edithiocarbamate (APDC) was used to form metallic complexes that could be retained in a SPE column which was packed with powder activated carbon. The analytes were eluted from the column by nitric acid in acetone. The metal concentrations were determined by flame and graphite atomic absorption spectroscopy. The effects of flow rate, APDC concentration, and pH were investigated. The proposed method was validated. The method detection limits were 11.7, 13.4, 10.1, and 25.3 µg kg^?1 for Cd, Ni, Pb, and Zn, respectively. The recoveries and RSDs were within the range of 81.9–101.1% and 0.6–6.0%, respectively. The method has potential merit for heavy metal determination in fish tissue.     

Separation of gold from Cu, Pt, Pd, Ni, Zn, Cd and Hg using triphenylarsine oxide as an extractant

A method is developed for extraction of gold(III) (75–300 g) from hydrochloric acid solution with triphenylarsine oxide dissolved in toluene as extradant. Gold(III) is determined spectrophotometrically with stannous chloride. The extraction is quantitative from 1.5–1.9M hydrochloric acid with 0.25% triphenylarsine oxide and an equilibration period of 30s. The method permits separation of gold(III) from Cu(II), Pt(IV), Pd(II), Ni(II), Zn(II), Cd(II) and Hg(II) and its spectrophotometric determination in ayurvedic medicines. The recovery and relative standard deviation obtained are >99.0% and <1.0%.     

Dosage electrochimique du cobalt : II. Applications aux Aciers à Faible ou à Moyenne Teneurs

Electrochemical determination of cobalt. Part I. Studies of current—voltage curves of the cobalt(III)/cobalt(II) system in picolinic acid mediaAs a preliminary to the development of electrochemical determinations of cobalt in steels, current—voltage curves at a platinum electrode were studied for the systems coblt(III)/cobalt(II) and iron(III)/iron(II) in media containing picolinic acid as complexing agent. Iron(III) oxidizes cobalt(II) in this complexmg medium, and the iron-(II) formed can be determined by an oxidant such as cerium(IV).     

Novel Imprinted Polymer for the Preconcentration of Cadmium with Determination by Inductively Coupled Plasma Mass Spectrometry

A novel Cd(II)-imprinted polymer was prepared with chemical immobilization using N-methacryloyl-L-Histidine as a vinylated chelating agent for online solid-phase extraction of Cd(II) for determination by inductively coupled plasma mass spectrometry. The Cd(II)–monomer complex was synthesized and copolymerized through bulk polymerization method in the presence of ethyleneglycoldimethacrylate cross-linker. The resulting polymer was leached with 1.0?mol?L^?1 HNO₃ to generate the cavities in the polymer for Cd(II) ions. The experimental conditions, including load pH, solution flow rate, and eluent concentration for effective sorption of Cd(II), were optimized using a minicolumn of the imprinted polymer. A volume of 5.0?mL sample 5?µg?L^?1 Cd(II) solution at pH 6.5 was loaded on the column at 2.0?mL?min^?1 using a sequential injection system followed by elution with 1.0?mL of 0.75?mol?L^?1 HNO₃. The relative selectivity coefficients of the imprinted polymer for Cd(II) were 38.5, 3.5, 3.0, 2.5, and 6.0 in the presence of Cu(II), Ni(II), Zn(II), Co(II), and Pb(II), respectively. Computational calculations revealed that the selectivity of the imprinted polymer was mediated by the stability of Cd(II)–N-methacryloyl-L-Histidine complex which was more stable than commonly used monomers including 4-vinyl pyridine, methacrylic acid, and vinylimidazole. The detection limit and relative standard deviation were 0.004?µg?L^?1 and 3.2%, respectively. The method was validated by the analysis of seawater certified reference material (CASS-4) and successfully used for the determination of Cd(II) in coastal seawater and estuarine water.     

Selective solid phase extraction of trace cadmium(II) and lead(II) from biological and natural water samples by ofloxacin-modified-silica gel

Ofloxacin was successfully used as a chemical modifier to improve the reactivity of silica gel in terms of selective binding and extraction of heavy metal ions. This new functionalised silica gel (SG-ofloxacin) was as an effective sorbent for the solid-phase extraction (SPE) of Cd(II) and Pb(II) in biological and natural water samples and their determination by inductively coupled plasma optical emission spectrometry (ICP-OES). Experimental conditions for effective adsorption of trace levels of Cd(II) and Pb(II) were optimised with respect to different experimental parameters using the batch and column procedures. The time for 70% sorption for Cd(II) and Pb(II) was less than 2 min. Complete elution of the adsorbed metal ions from the SG-ofloxacin was carried out using 2.0 mL of 0.5 mol L^?1 of HCl. Common coexisting ions did not interfere with the separation and determination at pH 4.0. The maximum static adsorption capacity of the sorbent at optimum conditions was found to be 39.17 and 48.69 mg g^?1 for Cd(II) and Pb(II), respectively. The detection limits of the method were found to be 0.29 and 0.13 ng mL^?1 for Cd(II) and Pb(II), respectively. The relative standard deviation (RSD) of the method under optimum conditions was lower than 3.0% (n = 5). The method was applied to the recovery of Cd(II) and Pb(II) from the certified reference material (GBW 08301, river sediment) and to the simultaneous determination of these cations in different water and biological samples with satisfactory results and yielding 100-folds enrichment factor.     

SPE and determination by FAAS of heavy metals using a new synthesized polymer resin in various water and dried vegetables samples

Firstly, poly[phenyl thiadiazole methacrylamide-co-divinylbenzene-co-2-acrylamido-2-methylpropane sulfonic acid] (PTMAAm-co-DVB-co-AMPS), a new polymer resin was synthesized. This polymer resin was characterized by elemental analyzer, X-ray diffractometer, scanning electron microscope (SEM) and IR spectrometer. The glass column packed with the synthesized polymer resin was used for solid phase extraction (SPE). At the same time, the analytes were separated and preconcentrated from various water, dried vegetables samples and standard reference material (CRM) with SPE and determined by flame atomic absorption spectrometer (FAAS). The experimental conditions of this method such as pH, flow rates of sample, flow rates of eluent, type / concentration / volume of eluent, sample volume and matrix ions were examined. The limits of detection (µg L^?1) were calculated (3s) 0.9 for Mn(II), 1.4 for Cd(II), Co(II) and Zn(II), 1.5 for Cr(III), 2.2. for Cu(II), 1.9 for Pb(II),1.5 for Ni(II) and 1.9 for Fe(III) (n = 21). The low relative standard deviation, ≤ 2% (n = 11) and preconcentration factor as 75 for analytes were obtained.     

Silica gel modified with Eriochrome Blue SE as a sorbent in trace analysis for metal ions

The sorption of 14 metal ions on silica gel impregnated with a mixture of Aliquat 336 and Eriochrome Blue SE was investigated. It was found that the sorption behaviour depends upon the species and the pH of the loading solution. Alkali metal ions were not retained under any of the investigated conditions. The retained metal ions can be eluted with dilute solutions of hydrochloric or perchloric acid without significant elution of the chelating reagent from the sorbent. The sorbent was used for the separation of metal ion mixtures by column — extraction chromatography and for additional purification of some salt solutions from trace amounts of Zn, Cd, Pb and Cu. The effectiveness of purification was confirmed by anodic stripping voltammetry.     

Use of clinoptilolite loaded with 1-(2-pyridylazo)-2-naphthol as a sorbent for preconcentration of Pb(II), Ni(II), Cd(II) and Cu(II) prior to their determination by flame atomic absorption spectroscopy

A solid phase extraction system for separation and preconcentration of trace amounts of Pb(II), Ni(II), Cd(II) and Cu(II) is proposed. The procedure is based on the adsorption of Pb²⁺, Ni²⁺, Cd²⁺ and Cu²⁺ ions on a column of 1-(2-pyridylazo)-2-naphthol (PAN) immobilised on surfactant-coated clinoptilolite prior to their determinations by Flame Atomic Absorption Spectroscopy (FAAS). The effective parameters including pH, sample volume, sample flow rate and eluent flow rate were also studied. The analytes collected on the column were eluted with 5 mL of 1 mol L^?1 nitric acid. A concentration factor of 180 can be achieved by passing 900 mL of sample through the column. The detection limits (3 s) for Cd, Cu, Pb and Ni were found to be 0.28, 0.12, 0.44 and 0.46 µg L^?1, respectively. The relative SDs at 10 µg L^?1 (n = 10) for analytes were in the range of 1.2–1.4%. The method was applied to the determination of Pb, Ni, Cd and Cu in water samples.     

Anodic stripping voltammetric determination of lead and cadmium in soil extracts

Two single-step extraction procedures validated by BCR, extraction with 0.43 mol dm⁻³ acetic acid and 0.05 mol dm⁻³ EDTA, are used for assessing bioavailable species of Pb and Cd in soils. After an extensive study of interferences of humic substances and using standard additions procedures, the extractable contents of Pb and Cd have been determined by DPASV directly in soil extracts with a good reproducibility (RSD varied from 1.0 to 7.9 %). Pb(II) and Cd(II) were released from complex in EDTA extracts by pH adjustment to 1 with 1 mol dm⁻³ HCl. The results were compared with those obtained with atomic absorption spectrometry and indicated reasonable agreement of both methods. Exchangeable forms represented 0.2 to 3.3 % and 13.0 to 63.6 % of total content of Pb and Cd in soils, respectively. EDTA extraction released from soils 7.9 to 29.9 % and 33.5 to 59.6 % of total content of Pb and Cd, respectively.     

Sorption and preconcentration of some heavy metals by 2-mercaptobenzothiazole-clay

2-Mercaptobenzothiazole loaded on previously treated clay was prepared, characterized and used for sorption and preconcentration of Hg(II), Pb(II), Zn(II), Cd(II), Cu(II) and Mn(II) from an aqueous solution. The support used was a natural clay previously treated with sulphuric acid solution. Adsorption isotherms of metal ions from aqueous solutions as function of pH were studied at 298 K. Conditions for quantitative retention and elution were established for each metal by batch and column methods. The chemically treated clay was very selective to Hg(II) in solution in which Zn(II), Cd(II), Pb(II), Cu(II) and Mn(II) were also present.     

Preconcentration and separation of silver from neutron poisons and rare earths using diphenyl-2-pyridylmethane as an extractant

The extraction of silver from aqueous thiocyanate-perchlorate solutions using diphenyl-2-pyridylmethane (DPPM) in benzene has been investigated. The variables such as concentrations of perchloric acid, thiocyanate and DPPM influencing the extraction have been optimized. Maximum extraction has been achieved from 0.01 M perchloric acid solution containing 0.01 M potassium thiocyanate in 0.075 M DPPM in benzene. The extraction was found to be independent of silver concentration in the range from 10^–4–10^–6 M. The influence of several anions on the extraction was examined; only thiosulphate interfered seriously and reduced the extraction below 1%. Thus 0.1M potassium thiosulphate was found to back-extract silver quantitatively in one step. Under selected optimal conditions, very small extraction (<1%) was observed for trivalent Gd, Dy, Ho, Tm, Yb, Lu; Cs(I) and Cd(II) and separation factors for these elements were better than 10³. Only Sn(IV) exhibited quantitative extraction (>99%). This extraction procedure can be used for the preconcentration of silver and tin or their separation from rare earths mentioned above.     

Extraction and preconcentration of toxic metal ions from aqueous solution using benzothiazole-based chelating resins

Polystyrene-divinylbenzene resin (PS-DVB) was functionalized with a benzothiazole group. PS-DVB with amino group was initially prepared by nitration and reduction reactions and subsequently treated with ethyl 2-benzothiazolylacetate (BA) to obtain the chelating resin with an amide linkage (BA-PS-DVB). Meanwhile, the amino-PS-DVB was diazotized and coupled with BA to obtain the chelating resin with an azo linkage (azo-BA-PS-DVB). The resins were characterized by elemental analysis and infrared spectroscopy and evaluated for their extraction of Cd(II), Cu(II) and Pb(II) ions in water before their determinations by flame atomic absorption spectrometry (FAAS). Extraction conditions were optimized for batch method such as the pH of the solution, the extraction time and the adsorption isotherm. The optimum pH for the extraction of Cd(II), Cu(II) and Pb(II) are 8.0, 7.0 and 6.0, respectively, while the equilibrium time of all ions was reached within 10-20 min. The adsorption behavior of all the metal ions followed the Langmuir adsorption isotherm. In the column method, the optimum flow rates of metal sorption onto BA-PS-DVB and azo-BA-PS-DVB columns were 2.5 and 4.0 mL min^− 1. Metal ions sorbed onto columns were eluted by 0.5 to 2.0 M HNO₃. The preconcentration factors of Cd(II) and Cu(II) on azo-BA-PS-DVB and Cu(II) on BA-PS-DVB were 50, 50, and 20, respectively. The present column method gave acceptable validation results: 71.2 and 74.0% recovery for Cd(II) and Cu(II) and an overall relative standard deviation (R.S.D) less than 10% (n = 15). The proposed method was applicable for determining Cu(II) in drinking water.     

Equilibrium and kinetics of Zn(II) bromide extraction with Amberlite LA-2 and methyl isobutyl ketone

The rates of extraction of Zn(II) from hydrobromic acid solutions into benzene solutions of the liquid anion exchanger Amberlite LA-2 and those into methyl isobutyl ketone (MIBK) have been investigated. The distribution equilibria of this system have been also studied. Under the used experimental conditions the extracted species of Zn(II) have been proposed. The kinetic data indicated a first order reaction with respect to Zn(II) in both systems, nearly one with respect to HBr and from 0–0.38 for LA-2. In case of extraction of Zn(II) with methyl isobutyl ketone, MIBK, the reaction order with respect to MIBK was found to be 4 and with respect to HBr inverse first order. The rate constants of these extraction processes were determined and the rate determining steps were discussed in the light of the obtained results.     

Studies on tetrachlorodithizone isomers and their applications to the extraction of metal ions

Six isomeric tetrachlorodithizones were synthesized and their electronic and i.r. spectra were measured. Their acid dissociation constants and partition coefficients between 0.5 M NaClO₄ solution and carbon tetrachloride are reported. Their extraction equilibria with Cd(II). Co(II), Cu(II), Hg(II), Ni(II), Pb(II), Tl(I), Zn(II) and Bi(III) and the spectrophotometric characteristics of the complexes formed are described. The 3,3',4,4'-tetrachloro isomer is spectrophotometrically more sensitive than dithizone for Zn, Pb, Hg(II) and Bi(III) whereas the 2,2',3,3'- and 2,2',5,5'-isomers are more sensitive for copper ions. For most of the metals tested, the tetrachlorodithizones allowed quantitative extraction at lower pH than is possible with dithizone.     

Preparation and evaluation of an ion imprinted sol–gel material for selective solid-phase extraction of Ni(II)

An ion imprinted silica sorbent was prepared using a sol–gel process for selective extraction of Ni(II) ions from water samples. Bis(dibenzoylmethanto)nickel(II) complex was used as template; phenyltrimethoxysilane and 3-aminopropyltriethoxysilane as functional monomers and tetraethylorthosilicate as reticulating agent. The material was packed in solid-phase extraction (SPE) column. The effect of sampling volume, elution conditions, sample pH and sample flow rate on the extraction of Ni ions from water samples were studied. The relative selectivity coefficients of imprinted sorbent for Ni(II)/Co(II), Ni(II)/Cu(II) and Ni(II)/Cd(II) were 23.7, 30.3 and 24.4, times greater than non-imprinted sorbent, respectively. The relative standard deviation of the eight replicate determinations of Ni(II) was 4.2%. The detection limit was 0.9 µg L^?1 using flame atomic absorption spectrometry. The developed method was successfully applied to the determination of trace nickel in water samples.