40Cr钢表面激光熔覆层的磨损性能

 为研究模具钢熔覆层的磨损性能,采用铁基粉在40Cr钢表面进行激光熔覆,以激光熔覆层为上试样,GCr15钢珠为下试样,采用HT－500磨损试验机进行摩擦磨损试验,并与40Cr基体的磨损性能相对比。利用表面形貌仪测量磨痕深度和宽度。研究结果表明：载荷小于250 g时,相同载荷下基体的摩擦系数大。载荷小于300 g时,随磨损时间延长,熔覆层、基体的摩擦系数都随着载荷增加而减小。当载荷为300 g时,基体的摩擦系数在0.563～0.589之间变化,平均值为0.576,且随时间逐渐升高,耐磨性变差;熔覆层的磨擦系数在0.431～0.457之间变化,平均摩擦系数为0.444,磨痕深度和宽度分别是0.65 mm和1.096 μm,且随时间逐渐下降,表现了良好的耐磨性能。当载荷增加到500 g时,平均摩擦系数和磨痕深度比300 g时分别增加了75％和47倍,且摩擦系数逐渐升高,磨损性能下降。     

40Cr钢表面激光熔覆层的磨损性能

为研究模具钢熔覆层的磨损性能,采用铁基粉在40Cr钢表面进行激光熔覆,以激光熔覆层为上试样,GCr15钢珠为下试样,采用HT－500磨损试验机进行摩擦磨损试验,并与40Cr基体的磨损性能相对比。利用表面形貌仪测量磨痕深度和宽度。研究结果表明：载荷小于250 g时,相同载荷下基体的摩擦系数大。载荷小于300 g时,随磨损时间延长,熔覆层、基体的摩擦系数都随着载荷增加而减小。当载荷为300 g时,基体的摩擦系数在0.563～0.589之间变化,平均值为0.576,且随时间逐渐升高,耐磨性变差;熔覆层的磨擦系数在0.431～0.457之间变化,平均摩擦系数为0.444,磨痕深度和宽度分别是0.65 mm和1.096 μm,且随时间逐渐下降,表现了良好的耐磨性能。当载荷增加到500 g时,平均摩擦系数和磨痕深度比300 g时分别增加了75％和47倍,且摩擦系数逐渐升高,磨损性能下降。     

激光熔覆TiC陶瓷涂层的组织和摩擦磨损性能研究

采用激光熔覆技术在TC4合金表面上制备了TiC陶瓷涂层,分析了熔覆层的微观组织,测试了熔覆层的硬度和摩擦磨损性能。结果表明:TiC激光熔覆层分为熔覆区和稀释区两个区域,熔覆区未受到基底的稀释,由TiC颗粒和TiC树枝晶组成;稀释区受到了基底的稀释,由TiC树枝晶和钛合金组成;TiC激光熔覆层的显微硬度在HV700~1500之间,明显地改善了TC4合金表面的摩擦和磨损性能。     

激光熔覆NiCrBSi涂层组织及摩擦磨损性能

采用激光熔覆技术在H13钢表面制备了NiCrBSi合金涂层,利用OM,SEM,EDX和XRD等对熔覆层的微观组织进行了分析,测试了熔覆层的显微硬度和摩擦磨损性能。结果表明,激光熔覆层与基体形成了良好的冶金结合,熔覆层的组织主要由γ-Ni,Cr7C3和CrB等相组成。熔覆层显微硬度在650~850HV之间,明显高于H13钢基体的硬度。摩擦磨损实验表明,在相同的条件下,熔覆层的耐磨性比基体有了明显的提高,磨损体积减少了92.4%。通过对磨损后的试样进行粗糙度测试后表明,涂层具有更平滑的表面。     

Investigation on friction and wear behaviors of FeS films on L6 steel surface

Low temperature ion sulfuration technique was utilized to prepare the solid lubrication iron sulfide (FeS) film on the surface of die-steel AISI L6. The friction and wear behaviors of sulfurized L6 steel were investigated on the ring-on-block tester of MM-200 under dry sliding condition. Atomic force microscopy and scanning electron microscopy were adopted to analyze the morphologies and compositions of surfaces and wear scars of the FeS film. X-ray diffractometer was used to study the film phase structure. Scanning Auger microprobe was employed to detect the elements distribution with depth. The results showed that the tribological properties of sulfurized L6 steel were superior to that of the unsulfurized one.     

Strength and wear resistance of nanocrystal structures on friction surfaces of steels with martensitic base

The formation of nanocrystal -martensite structures (NCS) in the surface layers of carbon and alloy steels under conditions of sliding friction and abrasion is investigated by electron microscopic, x-ray, and metallographic methods. The influence of the dynamic strain aging of martensite and strain dissolution of the carbide phase on the strength (microhardness and shear resistance) and tribological properties (wear resistance and friction coefficient) of nanocrystal surface layers of steels with martensitic base is demonstrated. The role of nanocrystal martensite in adhesive, abrasive, and fatigue wear resistance of steels is examined. The negative influence of the oxidizing air environment on the effective strength and wear resistance of friction NCS is demonstrated. The increased resistance of friction NCS of high-carbon steel to softening after tempering and friction heating is established.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 8, pp. 65–80, August, 2004.     

飞秒激光烧蚀0Cr18Ni9不锈钢精度的影响因素

为了研究影响飞秒激光烧蚀0Cr18Ni9不锈钢精度的因素,采用飞秒激光对0Cr18Ni9不锈钢进行了切割和打孔实验。利用光学显微镜、光学金相显微镜等设备,对不锈钢烧蚀区形貌和切缝显微组织进行检测,基于烧蚀过程中CCD实时采集到的不锈钢表面的激光光斑图样,采用COMSOL Multiphysic数值模拟软件,模拟了烧蚀过程中激光束的发散传播行为,并计算了光束发散角。结果表明：当激光重复频率为5 kHz时,厚度为160 m的0Cr18Ni9不锈钢切缝和孔边缘被明显烧黑,切缝处晶粒明显长大,存在热影响区;烧蚀过程中,由飞秒激光超高功率密度所致的金属-空气混合等离子体使光束沿传播方向上发生散射,发散角在6~10之间。热影响区的存在和混合等离子体的行为是影响飞秒激光烧蚀0Cr18Ni9不锈钢精度的主要因素。     

飞秒激光烧蚀0Cr18Ni9不锈钢精度的影响因素

为了研究影响飞秒激光烧蚀0Cr18Ni9不锈钢精度的因素,采用飞秒激光对0Cr18Ni9不锈钢进行了切割和打孔实验。利用光学显微镜、光学金相显微镜等设备,对不锈钢烧蚀区形貌和切缝显微组织进行检测,基于烧蚀过程中CCD实时采集到的不锈钢表面的激光光斑图样,采用COMSOL Multiphysic数值模拟软件,模拟了烧蚀过程中激光束的发散传播行为,并计算了光束发散角。结果表明:当激光重复频率为5kHz时,厚度为160μm的0Cr18Ni9不锈钢切缝和孔边缘被明显烧黑,切缝处晶粒明显长大,存在热影响区;烧蚀过程中,由飞秒激光超高功率密度所致的金属-空气混合等离子体使光束沿传播方向上发生散射,发散角在6°～10°之间。热影响区的存在和混合等离子体的行为是影响飞秒激光烧蚀0Cr18Ni9不锈钢精度的主要因素。     

Microstructure and friction and wear behavior of laser boronizing composite coatings on titanium substrate

Three kinds of laser boronizing composite coatings were in situ synthesized on Ti substrate by using powders of B, BN and B₄C as starting materials. Microstructures of the laser boronizing composite coatings were investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM); and their worn surface morphologies were also observed by using SEM. Moreover, the friction and wear behavior of the boronizing composite coatings under dry sliding condition were evaluated using a UMT-2MT friction and wear tester. It was found that all the three types of laser boronizing composite coatings had higher microhardness and better wear resistance than pure Ti substrate; and their microstructure and wear resistance varied with varying pre-placed powders of B, BN, and B₄C. Under the same dry sliding test conditions, the wear resistance of the three kinds of laser boronizing composite coatings, i.e., sample 1 prepared from pre-placed B, sample 2 obtained from pre-placed BN, and sample 3 fabricated from pre-placed B₄C, is ranked in an order of sample 1 > sample 2 > sample 3, which, surprisingly, well conforms to their order of hardness and friction coefficients.     

Multiscaling of lattice curvature on friction surfaces of metallic materials as a basis of their wear mechanism

A comprehensive structural study has been performed to explore deformation and wear debris formation on friction surfaces of metallic materials. A hierarchy of structural scales of plastic deformation and failure during wear has been established. The nanoscale plays the major role in the hierarchical self-organization of multiscale debris formation processes. On this scale, bifurcational interstitial states arise in zones of local lattice curvature, with plastic distortion and motion of nonequilibrium point defects which determine the nonlinear dynamics of structure formation and wear of surface layers. Nonequilibrium vacancies on lattice sites form microporosity through the coalescence mechanism under plastic distortion. The microporosity is a precursor of meso- and macroscale plastic shearing that defines wear debris formation.     

Rubber friction on smooth surfaces

We study the sliding friction for viscoelastic solids, e.g., rubber, on hard flat substrate surfaces. We consider first the fluctuating shear stress inside a viscoelastic solid which results from the thermal motion of the atoms or molecules in the solid. At the nanoscale the thermal fluctuations are very strong and give rise to stress fluctuations in the MPa-range, which is similar to the depinning stresses which typically occur at solid-rubber interfaces, indicating the crucial importance of thermal fluctuations for rubber friction on smooth surfaces. We develop a detailed model which takes into account the influence of thermal fluctuations on the depinning of small contact patches (stress domains) at the rubber-substrate interface. The theory predicts that the velocity dependence of the macroscopic shear stress has a bell-shaped form, and that the low-velocity side exhibits the same temperature dependence as the bulk viscoelastic modulus, in qualitative agreement with experimental data. Finally, we discuss the influence of small-amplitude substrate roughness on rubber sliding friction.     

On the surface topography of ultrashort laser pulse treated steel surfaces

This paper concentrates on observations of the surface topography by scanning electron microscopy (SEM) on alloyed and stainless steels samples treated by ultrashort laser pulses with duration of 210 fs and 6.7 ps. Globular-like and jet-like objects were found depending on the various levels of the fluence applied. It is shown that these features appear due to solid-liquid and liquid-gas transitions within surface layer irradiated by intense laser light. The observations are confronted to the theory of short-pulsed laser light-matter interactions, including interference, excitation of electrons, electron-phonon coupling as well as subsequent ablation. It is shown that the orientation of small ripples does not always depend on the direction of the polarization of laser light.     

Cr对TiC-VC增强铁基熔覆层耐蚀性及耐磨性的影响

通过X射线衍射、扫描电子显微镜、能谱仪、极化曲线和磨粒磨损实验分析,研究了不同Cr加入量对TiC-VC增强铁基激光熔覆层耐蚀性和耐磨性能的影响。结果表明:熔覆层中物相主要为α-Fe,TiC,VC和TiVC2。随着Cr加入量的增加,伴随有残余奥氏体及Cr3C2的出现,且Cr3C2呈长条状部分聚集、部分单独分布。熔覆层的耐蚀性与耐磨性随Cr加入量的增加呈现先增加后降低的趋势。熔覆粉末中加入适量的Cr元素能显著提高熔覆层的硬度与耐蚀性。当添加质量分数为3.0%的Cr时,熔覆层硬度高达1090HV0.2,且相同磨损条件下熔覆层磨损失重仅约为Q235钢的1/26;当添加质量分数为9.0%的Cr时,所得熔覆层的耐蚀性最好,约为不添加Cr时的3.26倍。     

Cr对TiC-VC增强铁基熔覆层耐蚀性及耐磨性的影响

通过X射线衍射、扫描电子显微镜、能谱仪、极化曲线和磨粒磨损实验分析,研究了不同Cr加入量对TiC-VC增强铁基激光熔覆层耐蚀性和耐磨性能的影响。结果表明：熔覆层中物相主要为-Fe,TiC,VC和TiVC2。随着Cr加入量的增加,伴随有残余奥氏体及Cr3C2的出现,且Cr3C2呈长条状部分聚集、部分单独分布。熔覆层的耐蚀性与耐磨性随Cr加入量的增加呈现先增加后降低的趋势。熔覆粉末中加入适量的Cr元素能显著提高熔覆层的硬度与耐蚀性。当添加质量分数为3.0%的Cr时,熔覆层硬度高达1090HV0.2,且相同磨损条件下熔覆层磨损失重仅约为Q235钢的1/26;当添加质量分数为9.0%的Cr时,所得熔覆层的耐蚀性最好,约为不添加Cr时的3.26倍。     

Structure and topography modifications of austenitic steel surfaces after friction in sliding contact

Friction experiments between two austenitic stainless steel (AISI 304L) surfaces in sliding contact were carried out under very low loads in two liquid environments, namely demineralized water and methanol, in order to study the correlation between surface damage (wear and surface topography) and structural modifications (phase formation and microstructure). The particularity of our approach was to perform the tests under Hertzian pressures, which were several orders of magnitude lower than the elastic limit of stainless steel. The structural modifications produced during friction were analysed by X-ray diffraction and transmission electron microscopy and the surface topography was studied by scanning electron microscopy and three-dimensional (3D) profiling. Whatever the experimental conditions investigated, the morphology of the damage observed on both surfaces consisted of very fine, smooth and parallel grooves typical of an abrasive wear process of a ductile material caused by the ploughing action of hard particles. From the beginning of the tests, the transformation of austenite into martensite was observed in the superficial layers and the dominant presence of martensite was identified in the wear debris. These results suggest that, under our experimental conditions, abrasion is the dominant mechanism of material removal. Received: 12 March 2002 / Accepted: 3 May 2002 / Published online: 10 September 2002 RID="*" ID="*"Corresponding author. Fax: +33-5/4949-6692, E-mail: jean.paul.riviere@univ-poitiers.fr     

不锈钢表面激光熔覆层与喷焊层耐磨性对比研究

本文研究在１Ｃｒ１８Ｎｉ９Ｔｉ基体上采用激光熔覆和离子喷焊二种工艺形成的涂层对耐磨性的影响。使用５ｋＷ横流ＣＯ２激光器对预置在基体上的Ｃｏ基自熔合金粉末进行单道或多道扫描，得到的熔层与等离子焊层对比结果是：激光熔层缺陷率低，成品率高，其结构致密均匀，晶粒细小，成分稀释率更小，对基体热影响小，熔层硬度与强韧性更高。性能试验证明：激光熔层具有更高的抗擦伤磨损和抗冲击滑动高温磨损性能，耐磨性提高了一倍左右。     

Plasma oxynitrocarburizing of 40Cr steel in an atmosphere of gasoline and air

A new plasma oxynitrocarburizing process in an air and gasoline atmosphere was developed. The influences of the atmosphere with different ratios of gasoline/air on the microstructure, surface hardness, and phase composition of 40Cr steel were characterized using optical microscope, scanning electron microscope (SEM), microhardness tester, and X-ray diffractometer (XRD), respectively. The experimental results showed that the plasma oxynitrocarburized layer was composed of bright layer and diffusion layer. It was found that the thickness, hardness, and Fe₃N concentration of the plasma oxynitrocarburized layer increased with the increment of ratio of gasoline/air.     

Formation of highly organised,periodic microstructures on steel surfaces upon pulsed laser irradiation

We present results on the growth of highly organised, reproducible, periodic microstructure arrays on a stainless steel substrate using multi-pulsed Nd:YAG (wavelength of 1064 nm, pulse duration of 7 ns, repetition rate of 25 kHz, beam quality factor of M ²∼1.5) laser irradiation in standard atmospheric environment (room temperature and normal pressure) with laser spot diameter of the target being ∼50 μm. The target surface was irradiated at laser fluence of ∼2.2 J/cm² and intensity of ∼0.31×10⁹ W/cm², resulting in the controllable generation of arrays of microstructures with average periods ranging from ∼30 to ∼70 μm, depending on the hatching overlap between the consecutive scans. The received tips of the structures were either below or at the level of the original substrate surface, depending on the experimental conditions. The peculiarity of our work is on the utilised approach for scanning the laser beam over the surface. A possible mechanism for the formation of the structures is proposed.     

Influence of laser contrast on high-order harmonic generation from solid-density plasma surfaces

The influence of laser temporal contrast on high-order harmonic generation from intense laser interactions with solid-density plasma surfaces is experimentally studied. A switchable plasma mirror system is set up to improve the contrast by two orders of magnitude at 10 ps prior to the main peak. By using the plasma mirror and tuning the prepulse, the dependence of high-order harmonic generation on laser contrast is investigated. Harmonics up to the 21 st order via the mechanism of coherent wake emission are observed only when the targets are irradiated by high contrast laser pulses by applying the plasma mirror.