Peculiarities of Acoustic Wave Reflection from a Boundary or Layer of a Two-Phase Medium

A mathematical model is presented for determining the oblique incidence of an acoustic wave at both a boundary and layer of a gas–drop mixture or a bubbly liquid of finite thickness. The basic wave reflection and transmission patterns are established for the incidence of a low-frequency acoustic wave at an interface between a pure gas and a gas–drop mixture, as well as between a pure and bubbly liquid. A range of varying volume fractions for a drop is determined, for which the zero value of the reflection coefficient is possible for low frequencies at oblique incidence. It is shown that the reflection coefficient will never be zero at angles of incidence above 24.5° from a gas–drop mixture at a pure gas boundary; however, when a wave is incident from a pure gas at a gas–drop mixture boundary, a zero reflection coefficient is possible for nonzero angles of incidence and the volume fraction of inclusions. The results of calculating reflection of an acoustic wave from a two-phase layer of a medium with a finite thickness are presented. It is established that the minimum reflection coefficient is possible depending on the perturbation frequency for a certain range of angles of incidence for the boundary or the layer of the gas–drop mixture, which is governed mainly by difference in densities between it and the pure gas.     

Measurement of the viscosity-density product using multiple reflections of ultrasonic shear horizontal waves

We have developed an on-line computer-controlled sensor, based on ultrasound reflection measurements, to determine the product of the viscosity and density of a liquid or slurry for Newtonian fluids and the shear impedance of the liquid for non-Newtonian fluids. A 14 MHz shear wave transducer is bonded to one side of a 45-90 degrees fused silica wedge and the base is in contract with the liquid. Twenty-eight echoes were observed due to the multiple reflections of an ultrasonic shear horizontal (SH) wave within the wedge. The fast Fourier transform of each echo was obtained for a liquid and for water, which serves as the calibration fluid, and the reflection coefficient at the solid-liquid interface was obtained. Data were obtained for 11 sugar water solutions ranging in concentration from 10% to 66% by weight. The viscosity values are shown to be in good agreement with those obtained independently using a laboratory viscometer. The data acquisition time is 14s and this can be reduced by judicious selection of the echoes for determining the reflection coefficient. The measurement of the density results in a determination of the viscosity for Newtonian fluids or the shear wave velocity for non-Newtonian fluids. The sensor can be deployed for process control in a pipeline, with the base of the wedge as part of the pipeline wall, or immersed in a tank.     

声波在水-含气沉积物界面的反射

含气泡海洋沉积物的声学特性是海底探测的重要问题。为了研究气泡存在对水-含气沉积物界面声反射系数的影响,本文基于气泡振动修正的Biot波动方程推导了气泡存在修正的Biot弹性模量,并结合水-沉积物界面的“开孔”边界条件推导了声波从水入射到水-含气沉积物界面的反射系数。数值分析表明气泡的振动导致反射系数呈现显著的频率特性。在气泡共振频率附近,由于气泡的共振引发的强散射和强衰减,使得反射系数很大,无论以何种角度入射,声波都很难进入含气泡的沉积物。本文研究结果表明,气泡半径、含量、声波频率以及入射角度都是影响水-含气沉积物界面反射系数的主要因素。      

The reflection of bounded inhomogeneous waves on a liquid/solid interface

Fourier analysis and normal mode theory are used to describe the reflection of bounded inhomogeneous waves on a liquid/solid interface. Nonspecular reflection phenomena in the Rayleigh angle are studied in detail. In this way, an explanation is given for the Rayleigh dip phenomenon for positive inhomogeneity factors and the related result of a reflection coefficient larger than unity when the sign of the inhomogeneity factor is reversed. In the limit of large beamwidths, the reflection coefficient predicted by the infinite plane inhomogeneous wave theory is obtained. These results are entirely consistent with the experimental work published by Deschamps [J. Acoust. Soc. Am. 96, 2841-2848 (1994)]. The energy efficiency of Rayleigh wave excitation is investigated as well. It is shown that for large beamwidths, the energy efficiency for bounded inhomogeneous waves is considerably higher in comparison with Gaussian and square-profiled beams.     

Spin-wave reflection from an interface of two Fermi liquids

The boundary condition for the magnetization jump at an interface of two Fermi liquids and the spin current through the interface is rederived. With the use of the derived condition the coefficient of reflection of a spin wave from a boundary of two Fermi liquids for normal incidence is found and applied to the case of interface of phase separated liquid mixture of ³He in ⁴He. The effect of the phase separation boundary on the coherently precessing spin pattern is discussed.     

海面冰层对声波的反射和散射特性

北极海面冰层复杂多变,其对声波的反射和散射严重影响冰下水声信道的传输特性,建立海面冰层的声波反射和散射模型对冰下水声通信研究具有重要意义.假设海面冰层为多层固体弹性介质且冰-水界面粗糙,满足微扰边界条件,导出声波从海水介质入射到海面冰层时相干反射系数满足的线性方程组.对相干反射系数随声波频率、掠射角、冰层厚度的变化进行数值分析.进一步引入根据散射声场功率谱密度计算散射系数的方法,改变掠射角,对冰层厚度、散射掠角对散射系数的影响进行研究.     

Acoustic method for obtaining the pressure reflection coefficient using a half-wave layer

This paper describes a method for obtaining the pressure reflection coefficient by using a half-wave layer. Two transducers were placed in reference liquid and test liquid respectively. The reference and test liquid were separated by the thin half-wave layer. Both transducers could operate in two modes. One acted as a transmitter and worked in pulse-echo mode, and the other operated in receiver mode. By adjusting the frequency of drive signal according to the thickness and material property of the half-wave layer, it was possible to generate the maximum interference signal of multiple waves reflected at the two interfaces of the layer. Therefore, the amplitude of reflection wave in steady-state depended only on the reflection coefficient at the interface between the half-wave layer and the test liquid. The effects of the signal-to-noise-ratio and the half-wave layer attenuation on the uncertainty characteristics of the pressure reflection coefficient were discussed. The experimental results showed high accuracy for measurement of reflection coefficient.     

Reflection of structural waves at a solid/liquid interface

This paper investigates the reflection characteristics of structural or guided waves in rods at a solid/liquid interface. Structural waves, whose wavelengths are much larger than the diameter of the rod, are described in a first approximation by classical one-dimensional wave theory. The reflection characteristics of such waves at a solid/liquid (melting) interface has been reported by two different ultrasonic measurement techniques: first, measuring the fast regression rate of a melting interface during the burning of metal rod samples in an oxygen-enriched environment, and second, monitoring the propagation of the solid/liquid interface during the slow melting and solidification of a rod sample in a furnace. The second work clearly shows that the major reflection occurs from the solid/liquid interface and not the liquid/gas interface as predicted by plane longitudinal wave reflectivity theory. The present work confirms this observation by reporting on the results of some specially designed experiments to identify the main interface of reflection for structural waves in rods. Hence, it helps in explaining the fundamental discrepancy between the reflection characteristics at a solid/liquid interface between low frequency structural waves and high frequency bulk waves, and confirms that the detected echo within a burning metallic rod clearly represents a reflection from the solid/liquid interface.     

Acoustoelastic analysis of reflected waves in nearly incompressible, hyper-elastic materials: forward and inverse problems

Many materials (e.g., rubber or biologic tissues) are "nearly" incompressible and often assumed to be incompressible in their constitutive equations. This assumption hinders realistic analyses of wave motion including acoustoelasticity. In this study, this constraint is relaxed and the reflected waves from nearly incompressible, hyper-elastic materials are examined. Specifically, reflection coefficients are considered from the interface of water and uni-axially prestretched rubber. Both forward and inverse problems are experimentally and analytically studied with the incident wave perpendicular to the interface. In the forward problem, the wave reflection coefficient at the interface is evaluated with strain energy functions for nearly incompressible materials in order to compute applied strain. For the general inverse problem, mathematical relations are derived that identify both uni-axial strains and normalized material constants from reflected wave data. The validity of this method of analysis is demonstrated via an experiment with stretched rubber. Results demonstrate that applied strains and normalized material coefficients can be simultaneously determined from the reflected wave data alone if they are collected at several different (but unknown) levels of strain. This study therefore indicates that acoustoelasticity, with an appropriate constitutive formulation, can determine strain and material properties in hyper-elastic, nearly incompressible materials.     

Measuring Newtonian viscosity from the phase of reflected ultrasonic shear wave

In this paper, an acoustic shear impedance model is employed to obtain a relation between the viscosity of a Newtonian fluid and phase characteristics of ultrasonic shear wave reflection from a solid-fluid interface. The phase and magnitude of the reflection coefficient can be decoupled in this model. The decoupling allows an independent relation between the acoustic shear impedance (viscosity-density product) and phase of the reflection coefficient. The model was experimentally verified for different fluid-solid combinations. Comparison of the results with the commonly used absolute reflection coefficient method demonstrates that phase measurement provides improved measurements.     

Measurement of viscosity and shear wave velocity of a liquid or slurry for on-line process control

An on-line sensor to measure the density of a liquid or slurry, based on longitudinal wave reflection at the solid-fluid interface, has been developed by the staff at Pacific Northwest National Laboratory. The objective of this research is to employ shear wave reflection at the solid-fluid interface to provide an on-line measurement of viscosity as well. Both measurements are of great interest for process control in many industries. Shear wave reflection measurements were conducted for a variety of liquids. By analyzing multiple reflections within the solid (only 0.63 cm thick-similar to pipe wall thickness) we increased the sensitivity of the measurement. At the sixth echo, sensitivity was increased sufficiently and this echo was used for fluid interrogation. Shear wave propagation of ultrasound in liquids is dependent upon the viscosity and the shear modulus. The data are analyzed using the theory for light liquids (such as water and sugar water solutions) and also using the theory for highly viscous liquids (such as silicone oils). The results show that, for light liquids, the shear wave reflection measurements interrogate the viscosity. However, for highly viscous liquids, it is the shear wave modulus that dominates the shear wave reflection. Since the density is known, the shear wave velocity in the liquid can be determined from the shear wave modulus. The results show that shear wave velocities in silicone oils are very small and range from 315 to 2389 cm/s. Shear wave reflection measurements are perhaps the only way that shear wave velocity in liquids can be determined, because the shear waves in liquids are highly attenuated. These results show that, depending on the fluid characteristics, either the viscosity or the shear wave velocity can be used for process control. There are several novel features of this sensor: (1) The sensor can be mounted as part of the wall of a pipeline or tank or submerged in a tank. (2) The sensor is very compact and can be located within the process stream. (3) The sensor can interrogate and characterize very attenuative liquids or slurries because the sensor operation depends upon reflection at the interface between the solid and the fluid, rather than on transmission through a liquid. (4) The sensor performance is not affected by fluid flow rate, entrained air, or vibration.     

电介质膜对受抑全内反射结构中古斯-汉欣位移的增强

受抑全反射结构中,反射光束和透射光束的古斯汉欣(Goos-Hanchen)位移同时存在,对称双棱镜结构的受抑全反射古斯汉欣位移通常只有波长量级,在实验中很难测量。计算了在入射角大于棱镜与空气界面的临界角小于棱镜与薄膜界面临界角时,镀有电介质膜的对称双棱镜的受抑全反射过程中入射光束的反射系数和透射系数的复数表达式。利用稳态相位法计算得出透射光束和全反射光束的古斯汉欣位移。结果表明,反射光束和透射光束古斯汉欣位移量相同,与入射角大小、薄膜厚度以及空气层厚度有关。在入射角小于但接近棱镜与薄膜界面的临界角,薄膜厚度和空气层厚度一定时,古斯汉欣位移量共振增强达到波长的数百倍。     

Explicit results for wave scattering and transmission through a rough fluid-fluid interface

This paper describes an analysis of reflection and transmission of acoustic waves from an imperfectly reflecting, rough fluid-fluid interface within the Kirchhoff approximation. It presents the results of calculations of the coherent and diffuse field. This work is motivated by the fact that few explicit results of the characteristics of the scattered and transmitted wave field exist in the literature for this problem. For the problem of interest, the surface reflection coefficient depends at each point upon the local angle between the incident wave and the rough surface. For surfaces with statistically independent local surface position and gradient, coherent field calculations show that the correction to constant reflection coefficient analyses is simply a multiplicative factor that depends upon the statistical characteristics of the surface gradient, sound speed and density ratio across the surface. This multiplicative factor is interpreted as an average reflection or transmission coefficient, <R> and <T>, respectively. The principle differences between these results and constant reflection coefficient analyses occur when waves impinge upon regions with higher sound speeds, where total internal reflection may occur. While the wave characteristics of smooth or constant reflection coefficient surfaces change abruptly in the vicinity of the angle of total internal reflection, the average reflection coefficient exhibits a much smoother dependence upon angle of incidence or sound speed ratio for rough surfaces. It is also shown that the direction of maximum diffuse scattering moves relative to its value were the reflection coefficient constant.     

Evaluation of interface wave velocity, reflection coefficients and interfacial stiffnesses of contacting surfaces

The phase velocity of the antisymmetric-mode interface wave as well as the longitudinal and shear wave reflection coefficients have been measured for contacting poly(methyl methacrylate) (PMMA) surfaces subjected to different contact pressures. It has been found that while the reflection coefficients decrease as the contact pressure is increased, the phase velocity of the interface wave increases from that of the Rayleigh wave toward that of the bulk shear wave. From these measurements, the normal and tangential interfacial stiffnesses of the contacting PMMA surfaces have been evaluated as functions of the contact pressure. As a result, the two independent procedures to evaluate the tangential stiffness, namely, from the interface wave velocity and from the shear wave reflection measurements, have yielded mutually consistent results. Furthermore, it has been found that the tangential/normal stiffness ratio and the shear/longitudinal reflection ratio of the contact interface are consistent with the predictions of an existing theoretical model for kissing bond interfaces.     

固-固界面退化特性的超声反射评价方法

提出了一种基于有限宽超声束反射的固-固界面退化特性评价方法,从理论和数值仿真角度进行了分析和计算。将两固体界面间的薄层简化为界面弹簧模型,以界面法向和切向劲度系数表征界面的退化程度。通过数值计算求得有限宽超声纵波束在不同入射角和界面不同退化程度下的反射横波、反射纵波的镜面反射系数。进一步地,通过建立二维有限元模型,仿真研究了有限宽超声纵波束在给定入射角及界面不同退化程度下镜面反射系数的变化规律。结果表明,反射纵波和反射横波的镜面反射系数随有限宽超声纵波束的入射角及界面劲度系数的改变而变化,且存在镜面反射系数随界面劲度系数单调且敏感变化的入射角,据此可准确评价界面的退化程度。     

玻璃与液晶非线性光学界面反射特性的研究

本文系统地研究了由玻璃与液晶构成的非线性光学界面。用一台调Q的红宝石激光器研究了由玻璃与处于各向同性液相的液晶所构成的非线性界面。在不同入射角时非线性界面由内部全反射跃变到部分透射的阈值光强与Kaplen的平面波理论计算结果相一致。在T-T_c=2.5℃条件下测量了时间分辨的非线性界面的反射率。观察到了反射率的滞后迴线。非线性界面的这种反射率的滞后迴线可以归之于液晶分子退取向的弛豫过程。用Ar⁺激光器研究了玻璃与向列相液晶所构成的非线性光学界面,观察到了由相变而产 关键词：     

On the validity and improvement of the ultrasonic pulse-echo immersion technique to measure real attenuation

A fundamental assumption embraced in conventional use of the ultrasonic pulse-echo immersion technique to measure attenuation in solid materials is revisited. The cited assumption relies on perfect and immutable adhesion at the water to sample interface, a necessary condition that allows calculating the reflection coefficient at any interface from elastic wave propagation theory. This parameter is then used to correct the measured signal and obtain the real attenuation coefficient of the sample under scrutiny. In this paper, cases in which the perfectly cohesive interfacial condition is not satisfied are presented. It is shown also that in those cases, the repeatability of the conditions at the interface is always uncertain. This implies that the reflection coefficients are unknown, even when density is known. A new method of simultaneously measuring the reflection coefficients for both exposed interfaces that are normal to the transducer, and the attenuation coefficient of the specimen is developed and is presented here. The robustness of the new method is proven, as we demonstrate that the proper value of attenuation is achieved independently of the continuously varying interfacial conditions of these non-ideal cases.     

Reflection and transmission of plane waves at the interface of pyroelectric bi-materials

A simple reflection and transmission theory of plane waves at the interface of pyroelectric media is studied in this paper. In an infinite homogeneous pyroelectric medium, there are four bulk wave modes: quasi-longitudinal (QL), two quasi-transversal (QT) and one temperature (T) waves, whose velocities depend on the frequency and incident angle. Simultaneously, a quasi-surface (QS) wave on each side of the interface of pyroelectric bi-materials will appear in the general reflection and transmission problem. The quasi-surface wave has the same wave vector component with the incident waves along the interface plane. So, the reflection and transmission problem is different with the propagation wave in the infinite homogeneous space, but it is still solvable. In the reflection and transmission problem, there are ten complex continuous conditions on the interface, which are satisfied by the bulk and quasi-surface waves together. Numerical calculations are performed for bi-material PZT-6B/BaTiO₃. Incidences of the quasi-longitudinal and quasi-transversal waves from the side of PZT-6B or BaTiO₃ medium are discussed. The reflection and transmission amplitude coefficients and energy flow ratios varying with the incident angle are examined.     

SPR棱镜传感器测量液体折射率的原理

推导了消失波函数的表达式,介绍了衰减全反射现象及SPR传感器测量液体折射率的原理,并利用SPR传感器测量了牛奶样品的反射系数及折射率与脂肪等主要成分含量的关系曲线.     

Theoretical Reflection Coefficient of Metal Grid Reflectors at a Dielectric Interface

Reflection properties of square apertures metal mesh mirrors are studied theoretically with the Finite-Difference Time-Domain (FDTD) method associated to Floquet Boundary Conditions. The reflector is illuminated by a normally incident plane wave and is located at an interface between two semi infinite low loss dielectric materials. Reflectivity and phase of the reflection coefficient are given in the non diffraction region for a wide range of square apertures, and for the four situations corresponding to an interface between free space and fused quartz.