THE ROLE OF LATTICE AND GASEOUS OXYGEN ON THE OXIDATIVE COUPLING OF METHANE STUDIED BY A PULSE REACTION TECHNIQUE

A comparative study of the role of lattice and gaseous oxygen in theoxidative coupling of methane over Na~ /Cao and Ca_xSr_(1-x)TiO_3 perovskiteoxide catalysts was performed by using a pulse reaction technique with CH_4,O_2 and mixtures of CH_4and O_2.It was found that there is an oxygen species onthe Surface of Cao which is active only for the total oxidation of methane at thereaction temperature.These oxygen species.once reacted with methane andconsumed,can be regenerated by the adsorption of oxygen molecules from thegas phase or by the migration of the lattice oxysen from the bulk onto thesurface.In contrast,no such oxygen species and no reaction can be detected bymethane pulsed over Ca_xSr_(1-x)TiO_3perovskite oxide catalysts.Na~ can heavilysuppress the non-selective oxygen species on the surface,and When 5mol%Na~ was incorporated onto the surface of Cao,the sample showed no reactivityto methane.When oxygen exists in the gas phase,or the pulse containsmethane and oxygen,the reaction over(Cao is mai     

无气相氧条件下La0.8Sr0.2Fe0.9Co0.1O3钙钛矿氧化物的氧物种直接氧化甲烷

以La0.8Sr0.2Fe0.9CO0.1O3钙钛矿氧化物作氧载体,采用连续流动反应和连续顺序Redox反应考察了氧物种氧化甲烷的反应性能.结果表明,连续流动反应中La0.8Sr0.2Fe0.9CO0.1O3氧化物的氧物种能选择氧化甲烷生成合成气.在适宜的再氧化条件下,通过连续顺序Redox反应实现了La0.8Sr0.2Fe0.9CO0.1O3氧化物的氧物种氧化甲烷连续生成合成气,消耗的氧物种可通过与气相氧反应而得到补充.但随着Redox反应的进行,氧化物的持续供氧性能下降,钙钛矿结构被破坏.     

Methane oxidation at redox stable fuel cell electrode La0.75Sr0.25Cr0.5Mn0.5O(3-delta)

Because of its widespread availability, natural gas is the most important fuel for early application of stationary fuel cells, and furthermore, methane containing biogases are one of the most promising renewable energy alternatives; thus, it is very important to be able to efficiently utilize methane in fuel cells. Typically, external steam reforming is applied to allow methane utilization in high temperature fuel cells; however, direct oxidation will provide a much better solution. Recently, we reported good electrochemical performance for an oxide anode La0.75Sr0.25Cr0.5Mn0.5O3 (LSCM) in low moisture (3% H2O) H2 and CH4 fuels without significant coking in CH4. Here, we investigate the catalytic activity of this oxide with respect to its ability to utilize methane. This oxide is found to exhibit fairly low reforming activity for both H2O and CO2 reforming but is active for methane oxidation. LSCM is found to be a full oxidation catalyst rather than a partial oxidation catalyst as CO2 production dominates CO production even in CH4-rich CH4/O2 mixtures. X-ray adsorption spectroscopy was utilized to confirm that Mn was the redox active species, clearly demonstrating that this material has the oxidation catalytic behavior that might be expected from a Mn perovskite and that the Cr ion is only present to ensure stability under fuel atmospheres.     

红外光谱研究甲烷和氧与SrO-La2O3/CaO表面的相互作用

在甲烷氧化偶联（ＯＣＭ）反应条件下，用原位红外光谱研究ＳｒＯ－Ｌａ２Ｏ３／ＣａＯ催化剂，结果表明，晶格氧使甲深度氧化，Ｌａ２Ｏ３和ＣａＯ具有活泼的晶格氧，ＳｒＯ的晶格氧比较稳定，气相氧通过催化剂表面消耗掉的晶格氧，加速甲烷了深度氧化，另一方面，催化剂表面的碳酸根物种在氧气氛下分解，在Ｌａ２Ｏ３和ＬＣ催化剂中，催化剂表面Ｌａ２Ｏ２（ＣＯ３）的分解形成配位不饱和的晶格氧Ｏ＾２－，并为气相氧吸附提供氧空     

化学循环重整甲烷制合成气LaBO3钙钛矿型氧载体研究

采用溶胶-凝胶法制备了不同B位可变价离子的La-B-O复合氧载体(B=Cr、Ni),采用XRD、BET、FT-IR、H2-TPR及CH4-TPSR等进行了表征,并用于化学循环重整(CLR)CH4反应中.结果表明,LaNiO3氧化物更易于与CH4发生深度氧化和选择氧化,LaCrO3氧化物则利于CH4裂解,其氧物种氧化CH4的能力较弱.在连续流动CLR反应中,LaNiO3具有较高的供氧量和持续供氧能力,能将CH4选择氧化为H2/CO=1.45的合成气,其CH4转化率和CO选择性分别达到23.4%和86.9%,且其结构保持了较高的稳定性.     

Unsteady-state direct partial oxidation of methane to synthesis gas in a fixed-bed reactor using AFeO3 (A = La, Nd, Eu) perovskite-type oxides as oxygen storage

Direct partial oxidation of methane to synthesis gas on AFeO(3) (A = La, Nd, Eu) oxides by a novel sequential redox cyclic reaction in the absence of gaseous oxygen was investigated over a fixed-bed reactor. These oxides were prepared by the sol-gel method and characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) techniques. XRD analysis showed that all AFeO(3) (A = La, Nd, Eu) oxides, calcined at 1173 K, are single-phase perovskites. The CH(4)-TPSR/MS and continuous reaction experiments indicated that the AFeO(3) (A = La, Nd, Eu) oxides provide mostly oxygen species, as the sole oxidant originated from lattice oxygen instead of gaseous oxygen, which can oxidize CH(4) to synthesis gas with high selectivity in the absence of gaseous oxygen. In terms of material economics and the amount of oxygen species for synthesis gas formation, the LaFeO(3) sample exhibits the best performance among these tested AFeO(3) oxides for synthesis gas production. The pulse experiments at different temperatures showed that the rate of oxygen migration during the CH(4) reaction with LaFeO(3) is strongly affected by the reaction temperature, and increases with rising temperature, which is favorable to much more CH(4) selective oxidation at high temperature. The two types of oxygen species are identified by experiments of continuous reactions and pulses, and confirmed by XPS. Methane can be converted selectively to synthesis gas by consumption of lattice oxygen, and general carbonaceous deposits on the catalyst surface do not occur under the appropriate reaction conditions by sequential redox cycles. The performance of selective oxidation of CH(4) to synthesis gas can be recovered by reoxidation using gaseous molecular oxygen; the LaFeO(3) oxide maintains relatively high catalytic activity and structural stability in redox atmospheres.     

La—Cu—Mn系钙钛矿型（ABO3）催化剂性能

采用共沉淀法制得了Ｃｕ２＋部分取代Ｌａ３＋的Ｌａ１－ｘＣｕｘＭｎＯ３钙钛矿型催化剂，通过ＸＲＤ、ＴＰＲ、电镜分析及活性评价，研究了Ｃｕ２＋的部分取代对Ｌａ１－ｘＣｕｘＭｎＯ３系催化剂性能的影响．结果表明，Ｃｕ２＋部分取代Ｌａ３＋后，使催化剂易被还原，活化能降低，对ＣＨ４、ＣＯ氧化反应，均有最佳取代量使催化剂的活性最佳，其值分别为０．２和０．４，这是由于随ｘ值的增大，催化剂晶格缺陷增多，晶格氧的化学势增大的缘故     

Hydrogen production from a combination of the water-gas shift and redox cycle process of methane partial oxidation via lattice oxygen over LaFeO3 perovskite catalyst

A redox cycle process, in which CH4 and air are periodically brought into contact with a solid oxide packed in a fixed-bed reactor, combined with the water-gas shift (WGS) reaction, is proposed for hydrogen production. The sole oxidant for partial oxidation of methane (POM) is found to be lattice oxygen instead of gaseous oxygen. A perovskite-type LaFeO3 oxide was prepared by a sol-gel method and employed as an oxygen storage material in this process. The results indicate that, under appropriate reaction conditions, methane can be oxidized to CO and H2 by the lattice oxygen of LaFeO3 perovskite oxide with a selectivity higher than 95% and the consumed lattice oxygen can be replenished in a reoxidation procedure by a redox operation. It is suggested that the POM to H2/CO by using the lattice oxygen of the oxygen storage materials instead of gaseous oxygen should be possibly applicable. The LaFeO3 perovskite oxide maintained relatively high catalytic activity and structural stability, while the carbonaceous deposits, which come from the dissociation of CH4 in the pulse reaction, occurred due to the low migration rate of lattice oxygen from the bulk toward the surface. A new dissociation-oxidation mechanism for this POM without gaseous oxygen is proposed based on the transient responses of the products checked at different surface states via both pulse reaction and switch reaction over the LaFeO3 catalyst. In the absence of gaseous-phase oxygen, the rate-determining step of methane conversion is the migration rate of lattice oxygen, but the process can be carried out in optimized cycles. The product distribution for POM over LaFeO3 catalyst in the absence of gaseous oxygen was determined by the concentration of surface oxygen, which is relevant with the migration rate of lattice oxygen from the bulk toward the surface. This process of hydrogen production via selective oxidation of methane by lattice oxygen is better in avoiding the deep oxidation (to CO2) and enhancing the selectivity. Therefore, this new route is superior to general POM in stability (resistance to carbonaceous deposition), safety (effectively avoiding accidental explosion), ease of operation and optimization, and low cost (making use of air not oxygen).     

Cu掺杂对LaMnO3催化剂的结构和催化氧化性能的影响

采用非晶态多核配合的方法合成了La1-xCuxMnO3(x=0、0.05、0.1、0.2、0.3、0.4、0.5)系列催化剂, 并用X射线衍射(XRD)、透射电镜(TEM)、比表面测定仪(BET)等手段对催化剂的微观结构进行了表征. 研究了Cu掺杂对钙钛矿结构及其对CO催化氧化发光性能及催化氧化CO、CH4性能的影响规律. 结果表明, 当x≤0.1 时, Cu掺杂仍可形成单相的钙钛矿结构; 当x>0.1时, 过量掺杂的Cu以CuO杂相存在. Cu掺杂可改善La1-xCuxMnO3催化剂对CO和CH4的催化氧化活性. 经700 ℃焙烧3 h制备的La0.9Cu0.1MnO3催化剂具有最高CO催化氧化活性(T100%=170 ℃), 该结果与CO催化氧化发光结果一致.而La0.95Cu0.05MnO3催化剂对CH4的催化氧化活性最高(T95%=705 ℃).     

Comparative study on the reaction of methane over a ZnO bed in the absence and presence of CO2

The reaction of zinc oxide with methane in the absence and presence of CO2 were theoretically and experimentally investigated using HSC Chemistry 5.1 software and a fixed bed reactor, respectively. In the absence of CO2 at 1193 K, the reduction of ZnO was accompanied with methane cracking, and metallic zinc, CO, and H2 were the main reaction products. This system could be utilized for the co-production of metallic zinc and synthesis gas, in which ZnO was a donor of oxygen. In the presence of CO2, ZnO plays as a catalyst in the CO2 reforming of methane and produces syngas with the average H2/CO ratio of 0.88 at 1193 K, which was close to the total reaction theoretic value of 1. It was also found that higher temperature favored high CH4 and CO2 conversions. XRD technique was used to characterize the ZnO species. The result showed that there were no differences in the peak profiles of the XRD patterns of the ZnO powder obtained before and after passing the CH4/CO2 mixed gases for 6 h at 1193 K. It is suggested that ZnO functions as a catalyst according to the redox cycle and metallic zinc plays the role of intermediate product in this process.     

甲烷与二氧化碳重整制取合成气反应的研究 (I)Sr_(1-x)La_xNiAl_(11)O_(19)催化活性表征

对具有磁铅石结构的Ｓｒ１－ｘＬａｘＮｉＡｌ１１Ｏ１９对甲烷与二氧化碳重整反应的催化活性、积炭量和稳定性进行了研究．不同还原温度下催化剂的ＸＲＤ和催化活性的实验结果表明，金属镍是ＣＨ４＋ＣＯ２重整反应的活性组分，金属镍含量越大，反应活性越高．反应后催化剂积炭量的分析结果说明，在相同镍含量和分散度的情况下，Ｌａ３＋离子对Ｓｒ２＋离子调变，可以降低催化剂的表面酸性，提高催化剂的抗积炭能力．ＬａＮｉＡｌ１１Ｏ１９是一种具有较好催化活性、稳定性和抗积炭性能的催化剂．     

Comparison of LaFeO3, La0.8Sr0.2FeO3, and La0.8Sr0.2Fe0.9Co0.1O3 perovskite oxides as oxygen carrier for partial oxidation of methane

Comparison of LaFeO3, La0.8Sr0.2FeO3, and La0.8Sr0.2Fe0.9Co0.1O3 perovskite oxides as oxygen cartier for partial oxidation of methane in the absence of gaseous oxygen was investigated by continuous flow reaction and sequential redox reaction. Methane was oxidized to syngas with high selectivity by oxygen species of perovskite oxides in the absence of gaseous oxygen. The sequential redox reaction revealed that the structural stability and continuous oxygen supply in redox re-action decreased over La0.8Sr0.2Fe0.9Co0.1O3 oxide, while LaFeO3 and Lao.sSro.2FeO3 exhibited excellent structural stability and continuous oxygen supply.     

Ca,Sr共掺杂铈氧化物及其在甲烷氧化偶联反应中的应用

采用柠檬酸法制备了Ca,Sr共掺杂的CeO_2催化剂,发现共掺杂催化剂较单掺杂或未掺杂催化剂呈现出更好的催化甲烷氧化偶联(OCM)反应性能.通过表征可知,Ca,Sr共掺杂催化剂的物相为CeO_2和SrCO_3,Ca高度分散或掺杂于CeO_2之中;CeO_2的粒径明显变小;表面呈中等程度碱性;Ce基催化剂上的亲电氧物种数量随着碱土金属的掺杂而增大,亲电氧物种与晶格氧摩尔比(O_2-2+O-2)/O-2的大小顺序(CeSrCaCe SrCeO_2)与C2选择性一致;且SrCO_3相的存在有助于Ce基氧化物催化甲烷氧化偶联反应(OCM)性能的改善.     

添加碱土金属化合物对CeO2甲烷氧化偶联催化性能的影响

天然气中甲烷的利用,特别是氧化偶联(OCM)制乙烯过程近年来成为多相催化研究的热点之一.自从1982年Keller和Bhasin提出该课题以来许多学者已进行了大量催化剂的研制工作.尽管在这方面已取得重要进展,但催化剂的性能距工业化要求还有较大差距.     

铈基与钴基Co3O4-CeO2氧载体上甲烷化学链转化特性: 产物选择性控制

采用水热法制备了Co₃O₄/CeO₂(x)[x为钴铈原子摩尔比n(Co):n(Ce)=6:49:1]和Ce_1-yCo_yO_2-δ(y=0.10.4)2个系列复合氧化物, 并表征了材料的物理化学性质, 考察了这些氧化物作为氧载体参与甲烷化学链转化(化学链燃烧和化学链部分氧化)的反应性能. 结果表明, 2类复合氧化物的甲烷反应活性均明显优于单一氧化物CeO₂或Co₃O₄, 但2类氧载体上的甲烷反应产物的选择性具有明显差异. Ce_1-yCo_yO_2-δ氧载体形成了Ce-Co-O固溶体, 储氧能力明显增强, 体相晶格氧迁移速率与甲烷活化速率匹配较好, 甲烷反应产物以CO和H₂的合成气为主, 有利于甲烷的化学链部分氧化. Co₃O₄/CeO₂(x)氧载体中CeO₂与Co₃O₄之间的相互作用改善了材料的储氧能力和氧化活性, 其与甲烷反应时主要生成CO₂, 有利于甲烷化学链燃烧. 连续性化学链循环实验表明, 2类氧载体均具有较好的再生性能和循环稳定性.     

CeO2-ZrO2-La2O3-Al2O3 composite oxide and its supported palladium catalyst for the treatment of exhaust of natural gas engined vehicles

Composite supports CeO2-ZrO2-Al2O3 (CZA) and CeO2-ZrO2-Al2O3-La2O3 (CZALa) were prepared by co-precipitation method. Palladium catalysts were prepared by impregnation and their purification ability for CH4, CO and NOx in the mixture gas simulated the exhaust from natural gas vehicles (NGVs) operated under stoichiometric condition was investigated. The effect of La2O3 on the physicochemical properties of supports and catalysts was characterized by various techniques. The characterizations with X-ray diffraction (XRD) and Raman spectroscopy revealed that the doping of La2O3 restrained effectively the sintering of crystallite particles, maintained the crystallite particles in nanoscale and stabilized the crystal phase after calcination at 1000 ℃. The results of N2-adsorption, H2-temperature-programmed reduction (H2-TPR) and oxygen storage capacity (OSC) measurements indicated that La2O3 improved the textural properties, reducibility and OSC of composite supports. Activity testing results showed that the catalysts exhibit excellent activities for the simultaneous removal of methane, CO and NOx in the simulated exhaust gas. The catalysts supported on CZALa showed remarkable thermal stability and catalytic activity for the three pollutants, especially for NOx. The prepared palladium catalysts have high ability to remove NOx, CH4 and CO, and they can be used as excellent catalysts for the purification of exhaust from NGVs operated under stoichiometric condition. The catalysts reported in this work also have significant potential in industrial application because of their high performance and low cost.     

Au/ZrLa掺杂 CeO2催化剂在CO氧化反应中优异的催化活性：锆镧协同作用

在过去的25年,纳米金催化剂上 CO氧化反应得到广泛研究,但始终没有一致的结论。这是因为影响纳米金催化活性的因素很多,包括金的价态、载体的性质、氧空位、金属与载体之间的相互作用等,尤其是各影响因素之间相互牵制,增加了催化反应机理的研究难度。氧化铈载体表面氧缺陷的浓度较高,有利于活性金属组分在其表面的稳定和分散,因此氧化铈纳米晶负载的 Au催化剂受到广泛关注。此外,当 CeO2晶格中部分 Ce被化学性质不同的其它元素取代后,可以促进 CeO2晶格氧的活化,提高氧的储放能力,从而有利于催化反应进行。因此,本文采用水热法合成了组成均匀的 CeO2, CeZrOx和 CeZrLaOx三个载体,并通过沉淀-沉积法负载金。利用 X射线衍射(XRD)、拉曼光谱(Raman)、X射线光电子能谱(XPS)、高分辨透射电镜(HRTEM)、X射线吸收精细结构(XAFS)和氢气程序升温还原(H2-TPR)等技术分析了催化剂的物相结构、表面性质、形貌以及金纳米颗粒的大小和价态等性质,并结合其在 CO氧化反应中催化性能的差异,探讨影响金催化剂活性的关键因素。 XRD, TEM, HRTEM和 XAFS结果表明,三个载体上所得金纳米颗粒的平均尺寸都在2–4 nm,且分散较好; XPS结果表明,影响催化剂活性的关键因素不是金的价态,而是载体表面的活性氧物种。从Raman结果可知,掺杂后的氧化铈载体上氧空位浓度明显增加,因而催化剂活性都有所提高。 H2-TPR进一步探讨了三个载体以及负载金后其氧化还原能力的变化,结果表明,金和载体之间的相互作用可以增强载体的氧化还原性能以及表面氧空位浓度,进一步提高了催化剂活性,而负载金催化剂氧化还原性能的变化与载体的组成密切相关。由于锆的掺杂可使金与载体之间相互作用减弱,而镧则增强了二者间相互作用,因此 Au/CeZrLaOx催化剂上锆和镧的协同掺杂作用使其表面活性氧物种浓度最高,低温时表现出最高的催化活性。     

Oxidative coupling of methane in a fixed bed reactor over perovskite catalyst： A simulation study using experimental kinetic model

The oxidative coupling of methane （OCM） to ethylene over a perovskite titanate catalyst in a fixed bed reactor was studied experimentally and numerically. The two-dimensional steady state model accounted for separate energy equations for the gas and solid phases coupled with an experimental kinetic model. A lumped kinetic model containing four main species CH4, O2, COx （CO2, CO）, and C2 （C2H4 and C2H6） was used with a plug flow reactor model as well. The results from the model agreed with the experimental data. The model was used to analyze the influence of temperature and feed gas composition on the conversion and selectivity of the reactor performance. The analytical results indicate that the conversion decreases, whereas, C2 selectivity increases by increasing gas hourly space velocity （GHSV） and the methane conversion also decreases by increasing the methane to oxygen ratio.     

甲烷催化部分氧化制合成气的反应机理

借助脉冲反应、质谱-程序升温表面反应（MS-TPSR）等技术研究了Ni／α-Al2O3催化剂上甲烷催化部分氧化制合成气（POM）的反应机理．结果表明,NiO上CH4不能解离产生H2只有当NiO被CH4还原为Ni0后,CH4才能解高产生H2,Ni0是CH4活化和POM反应的活性相;POM反应机理遵循直接氧化机理,CH4和O2均在Ni0上活化,活化过程形成的Ni…C和Niδ…Oδ物种是反应历程中的关键物种,Niδ …Oδ物种高选择性地与CH4解离产生的碳物种Ni…C反应生成CO．     

Hydrogen production from coke oven gas over LiNi/γ-Al2O3 catalyst modified by rare earth metal oxide in a membrane reactor

The performance of LiNi/r-Al2O3 catalysts modified by rare earth metal oxide (La2O3 or CeO2) packed on BCFNO membrane reactor was discussed for the partial oxidation of methane (POM) in coke oven gas (COG) at 875 ◦C. The NiO/r-Al2O3 catalysts with different amounts of La2O3 and CeO2 were prepared with the same preparation method and under the same condition in order to compare the reaction performance (oxygen permeation, CH4 conversion, H2 and CO selectivity) on the membrane reactor. The results show that the oxygen permeation flux increased significantly with LiNiREOx/r-Al2O3 (RE = La or Ce) catalysts by adding the element of rare earth especially the Ce during the POM in COG. Such as, the Li15wt%CeO29wt%NiO/ -Al2O3 catalyst with an oxygen permeation flux of 24.71 ml·cm−2·min−1 and a high CH4 conversion was obtained in 875 ◦C. The resulted high oxygen permeation flux may be due to the added Ce that inhibited the strong interaction between Ni and Al2O3 to form the NiAl2O4 phase. In addition, the introduction of Ce leads up to an important property of storing and releasing oxygen.