Preparation of non-oriented silicon steel with high magnetic induction using columnar grains

Columnar grains can lead to detrimental surface ridging and an inhomogeneous microstructure, although their {1 0 0}〈0 v w〉 texture is considered desirable due to their good magnetic properties in non-oriented silicon steel. Based on the hereditary tendency of {1 0 0}〈0 v w〉 texture, the effects of lubrication and heating rate on texture and on final magnetic properties were investigated using a cast slab containing 100% columnar grains. Hot rolling with lubrication, normalization at low heating rate, two-stage cold rolling, and final annealing at 1000 °C helped achieve high performance. As a result, a new non-oriented silicon steel with high magnetic induction (B₅₀=1.82 T) and low core loss (P_1.5=2.35 W/kg) was prepared. The possibility of further performance optimization was also discussed.     

Magnetic fluid poly(ethylene glycol) with moderate anticancer activity

Poly(ethylene glycol) (PEG)-containing magnetic fluids - magnetite (Fe₃O₄) stabilized by sodium oleate - were prepared. Magnetic measurements confirmed superparamagnetic behaviour at room temperature. The structure of that kind of magnetic fluid was characterized using different techniques, including electron microscopy, photon cross correlation spectroscopy and small-angle neutron scattering, while the adsorption of PEG on magnetic particles was analyzed by differential scanning calorimetry and Fourier transform infrared spectroscopy. From the in vitro toxicity tests it was found that a magnetic fluid containing PEG (MFPEG) partially inhibited the growth of cancerous B16 cells at the highest tested dose (2.1 mg/ml of Fe₃O₄ in MFPEG).     

Study of ferromagnetism in Bi2S3 and ZnS nanocrystalline powders

Results of magnetic measurements suggested that Bi₂S₃ and ZnS nanocrystalline powders prepared by hydrothermal method could possibly exhibit room temperature ferromagnetism. The measured saturation magnetization of the powders increases with an increase of annealing temperature from 300 to 500 °C. Ab initio calculations suggested that the cation vacancies on the surface of Bi₂S₃ and ZnS nanograins could be responsible for the observed magnetic moments. Heat-treatment of Bi₂S₃ or ZnS nanocrystalline powders in Bi or Zn vapor could bring about an enhancement of ferromagnetism. The calculation results indicated that the interstitial Bi or Zn atoms in Bi₂S₃ (0 0 1) or ZnS (0 0 1) surface could induce magnetic moments.     

Near room temperature magnetocaloric properties of melt-spun Gd100−xBx (x=0, 5, 10, 15, and 20 at%) alloys

The magnetocaloric properties of melt-spun Gd-B alloys were examined with the aim to explore their potential application as magnetic refrigerants near room temperature. A series of Gd_100−xB_x (x=0, 5, 10, 15, and 20 at%) alloys were prepared by melt spinning. With the decrease in Gd/B ratio, Curie temperature (T_C) remains constant at ∼293 K, and saturation magnetization, at 275 K, decreases from ∼100 to ∼78 emu/g. Negligible magnetic hysteresis was observed in these alloys. The peak value of magnetic entropy change, (−ΔS_M)_max, decreased from ∼9.9 J/kg K (0-5 T) and ∼5.5 J/kg K (0-2 T) for melt-spun Gd to ∼7.7 J/kg K (0-5 T) and ∼4.0 J/kg K (0-2 T), respectively for melt-spun Gd₈₅B₁₅ and Gd₈₀B₂₀ alloys. Similarly, the refrigeration capacity (q) decreased monotonously from ∼430 J/kg (0-5 T) for melt-spun Gd to ∼330 J/kg (0-5 T) for melt-spun Gd₈₀B₂₀ alloy. The near room temperature magnetocaloric properties of melt-spun Gd_100−xB_x (0≤x≤20) alloys were found to be comparable to few first-order transition based magnetic refrigerants.     

Enhanced growth of lactobacilli and bioconversion of isoflavones in biotin-supplemented soymilk upon ultrasound-treatment

This study aimed at utilizing ultrasound treatment to further enhance the growth of lactobacilli and their isoflavone bioconversion activities in biotin-supplemented soymilk. Strains of lactobacilli (Lactobacillus acidophilus BT 1088, L. fermentum BT 8219, L. acidophilus FTDC 8633, L. gasseri FTDC 8131) were treated with ultrasound (30 kHz, 100 W) at different amplitudes (20%, 60% and 100%) for 60, 120 and 180 s prior to inoculation and fermentation in biotin-soymilk. The treatment affected the fatty acids chain of the cellular membrane lipid bilayer, as shown by an increased lipid peroxidation (P < 0.05). This led to increased membrane fluidity and subsequently, membrane permeability (P < 0.05). The permeabilized cellular membranes had facilitated nutrient internalization and subsequent growth enhancement (P < 0.05). Higher amplitudes and longer durations of the treatment promoted growth of lactobacilli in soymilk, with viable counts exceeding 9 log CFU/mL. The intracellular and extracellular β-glucosidase specific activities of lactobacilli were also enhanced (P < 0.05) upon ultrasound treatment, leading to increased bioconversion of isoflavones in soymilk, particularly genistin and malonyl genistin to genistein. Results from this study show that ultrasound treatment on lactobacilli cells promotes (P < 0.05) the β-glucosidase activity of cells for the benefit of enhanced (P < 0.05) isoflavone glucosides bioconversion to bioactive aglycones in soymilk.     

Separation of PCR-ready DNA from dairy products using magnetic hydrophilic microspheres and poly(ethylene glycol)-NaCl water solutions

Carboxyl group-containing magnetic nonporous poly(2-hydroxyethyl methacrylate-co-glycidyl methacrylate) (P(HEMA-co-GMA)) and magnetic glass microspheres were used for the isolation of bacterial DNA. P(HEMA-co-GMA) microspheres were prepared by the dispersion polymerization in toluene/2-methylpropan-1-ol mixture in the presence of magnetite nanoparticles obtained by coprecipitation of Fe(II) and Fe(III) salts with ammonium hydroxide. Carboxyl groups were then introduced by oxidation of the microspheres with potassium permanganate. The most extensive DNA recovery was achieved at PEG 6000 concentrations of 12% or 16% and 2 M NaCl. The method proposed was used for bacterial DNA isolation from different dairy products containing Bifidobacterium and Lactobacillus cells. The presence of target DNA and the quality of isolated DNA were checked by polymerase chain reaction (PCR) amplification with specific primers.     

Effects of ultrasound on growth, bioconversion of isoflavones and probiotic properties of parent and subsequent passages of Lactobacillus fermentum BT 8633 in biotin-supplemented soymilk

This study aimed to evaluate the effects of ultrasound on Lactobacillus fermentum BT 8633 in parent and subsequent passages based on their growth and isoflavone bioconversion activities in biotin-supplemented soymilk. The treated cells were also assessed for impact of ultrasound on probiotic properties. The growth of ultrasonicated parent cells increased (P < 0.05) by 3.23-9.14% compared to that of the control during fermentation in biotin-soymilk. This was also associated with enhanced intracellular and extracellular (8.4-17.0% and 16.7-49.2%, respectively; P < 0.05) β-glucosidase specific activity, leading to increased bioconversion of isoflavones glucosides to aglycones during fermentation in biotin-soymilk compared to that of the control (P < 0.05). Such traits may be credited to the reversible permeabilized membrane of ultrasonicated parent cells that have facilitated the transport of molecules across the membrane. The growing characteristics of first, second and third passage of treated cells in biotin-soymilk were similar (P > 0.05) to that of the control, where their growth, enzyme and isoflavone bioconversion activities (P > 0.05) were comparable. This may be attributed to the temporary permeabilization in the membrane of treated cells. Ultrasound affected probiotic properties of parent L. fermentum, by reducing tolerance ability towards acid (pH 2) and bile; lowering inhibitory activities against selected pathogens and reducing adhesion ability compared to that of the control (P < 0.05). The first, second and third passage of treated cells did not exhibit such traits, with the exception of their bile tolerance ability which was inherited to the first passage (P < 0.05). Our results suggested that ultrasound could be used to increase bioactivity of biotin-soymilk via fermentation by probiotic L. fermentum FTDC 8633 for the development of functional food.     

Magnetic studies on ZnTe:Cr film grown on glass substrate by thermal evaporation method

ZnTe and ZnTe:Cr films were prepared on glass substrate by using thermal evaporation method. X-ray diffraction analysis revealed the presence of ZnCrTe phase. X-ray photoelectron spectroscopy was used to estimate the composition of as-prepared films. The valence state of Cr in ZnTe:Cr film is determined to be +2 by using electron spin resonance spectroscopy. Magnetic moment data as a function of magnetic field was recorded by using superconducting quantum interference device magnetometry at 300 K. The result showed a clear hysteresis loop with coercive field of 48 Oe. Magnetic domains were observed by using magnetic force microscopy and the average value of domain size was 3.7 nm.     

Crystal and magnetic structures of Y2CrS4

Chromium(II) sulfide, Y₂CrS₄, prepared by a solid-state reaction of Y₂S₃ and CrS, showed an antiferromagnetic transition at 65 K. The neutron diffraction patterns at 10 and 90 K were both well refined with the space group Pca2₁. At 90 K, cell parameters were a=12.5518(13) Å, b=7.5245(8) Å, and c=12.4918(13) Å. At 10 K, magnetic peaks were observed, which could be indexed on the same unit cell. Magnetic moments of chromium ions were parallel to the b-axis and antiferromagnetically ordered in each set of the 4a sites.     

In vitro study of magnetic particle seeding for implant assisted-magnetic drug targeting

The concept of using magnetic particles (seeds) as the implant for implant assisted-magnetic drug targeting (IA-MDT) was analyzed in vitro. Since this MDT system is being explored for use in capillaries, a highly porous (ε∼70%), highly tortuous, cylindrical, polyethylene polymer was prepared to mimic capillary tissue, and the seeds (magnetite nanoparticles) were already fixed within. The well-dispersed seeds were used to enhance the capture of 0.87 μm diameter magnetic drug carrier particles (MDCPs) (polydivinylbenzene embedded with 24.8 wt% magnetite) under flow conditions typically found in capillary networks. The effects of the fluid velocity (0.015–0.15 cm/s), magnetic field strength (0.0–250 mT), porous polymer magnetite content (0–7 wt%) and MDCP concentration (C=5 and 50 mg/L) on the capture efficiency (CE) of the MDCPs were studied. In all cases, when the magnetic field was applied, compared to when it was not, large increases in CE resulted; the CE increased even further when the magnetite seeds were present. The CE increased with increases in the magnetic field strength, porous polymer magnetite content and MDCP concentration. It decreased only with increases in the fluid velocity. Large magnetic field strengths were not necessary to induce MDCP capture by the seeds. A few hundred mT was sufficient. Overall, this first in vitro study of the magnetic seeding concept for IA-MDT was very encouraging, because it proved that magnetic particle seeds could serve as an effective implant for MDT systems, especially under conditions found in capillaries.     

Magnetic binary nanofillers

Magnetic binary nanofillers containing multiwall carbon nanotubes (MWCNT) and hercynite were synthesized by Chemical Vapor Deposition (CVD) on Fe/AlOOH prepared by the sol–gel method. The catalyst precursor was fired at 450 °C, ground and sifted through different meshes. Two powders were obtained with different particle sizes: sample A (50–75 μm) and sample B (smaller than 50 μm). These powders are composed of iron oxide particles widely dispersed in the non-crystalline matrix of aluminum oxide and they are not ferromagnetic. After reduction process the powders are composed of α-Fe nanoparticles inside hercynite matrix. These nanofillers are composed of hercynite containing α-Fe nanoparticles and MWCNT. The binary magnetic nanofillers were slightly ferromagnetic. The saturation magnetization of the nanofillers depended on the powder particle size. The nanofiller obtained from powder particles in the range 50–75 μm showed a saturation magnetization 36% higher than the one formed from powder particles smaller than 50 μm. The phenomenon is explained in terms of changes in the magnetic environment of the particles as consequence of the presence of MWCNT.     

Preparation and characterization of biocompatible magnetic carbon nanotubes

Magnetic carbon nanotubes consisting of multi-wall carbon nanotubes (MWNTs) core and Fe₃O₄ shell were successfully prepared by in situ thermal decomposition of Fe(acac)₃ or FeCl₃ or Fe(CO)₅ in 2-pyrrolidone containing acid treated MWNTs at 240 °C with the protection of nitrogen gas. The samples were characterized by TEM, XRD, SEAD, XPS and superconducting quantum interference device. Also, their biocompatibility was compared with naked carbon nanotubes. The results showed that after coated with Fe₃O₄ nanoparticles, the obtained magnetic carbon nanotubes show superparamagnetic characteristic at room temperature, and their blocking temperature is about 80 K. The magnetic properties of the nanotubes are relevant to the content of magnetic particles, increasing content of magnetic nanoparticles leads to higher blocking temperature and saturation magnetization. The results of antimicrobial activities to bacterial cells (Escherichia coli) showed that the MWNTs have antimicrobial activity, while the magnetic nanotubes are biocompatible even with a higher concentration than that of MWNTs.     

Preparation and in vitro evaluation of poly(D,L-lactide-co-glycolide) air-filled nanocapsules as a contrast agent for ultrasound imaging

The aim of this study was to prepare air-filled nanocapsules intended ultrasound contrast agents (UCAs) with a biodegradable polymeric shell composed of poly(d,l-lactide-co-glycolide) (PLGA). Because of their size, current commercial UCAs are not capable of penetrating the irregular vasculature that feeds growing tumors. The new generation of UCAs should be designed on the nanoscale to enhance tumor detection, in addition, the polymeric shell in contrast with monomolecular stabilized UCAs improves the mechanical properties against ultrasound pressure and lack of stability. The preparation method of air-filled nanocapsules was based on a modification of the double-emulsion solvent evaporation technique. Air-filled nanocapsules with a mean diameter of 370 ± 96 nm were obtained. Electronic microscopies revealed spherical-shaped particles with smooth surfaces and a capsular morphology, with a shell thickness of ∼50 nm. Air-filled nanocapsules showed echogenic power in vitro, providing an enhancement of up to 15 dB at a concentration of 0.045 mg/mL at a frequency of 10 MHz. Loss of signal for air-filled nanocapsules was 2 dB after 30 min, suggesting high stability. The prepared contrast agent in this work has the potential to be used in ultrasound imaging.     

Four-fold magnetic anisotropy in a Co film on MgO(0 0 1)

The development of devices based on magnetic tunnel junctions has raised new interests on the structural and magnetic properties of the interface Co/MgO. In this context, we have grown ultrathin Co films (≤30 Å) by molecular-beam epitaxy on MgO(0 0 1) substrates kept at different temperatures (T_S). Their structural and magnetic properties were correlated and discussed in the context of distinct magnetic anisotropies for Co phases reported in the literature. The sample characterization has been done by reflection high energy electron diffraction, magneto-optical Kerr effect and ferromagnetic resonance. The main focus of the work is on a sample deposited at T_S=25 °C, as its particular way of growth has enabled a bct Co structure to settle on the substrate, where it is not normally obtained without specific seed layers. This sample presented the best crystallinity, softer magnetic properties and a four-fold in-plane magnetic anisotropy with Co〈1 1 0〉 easy directions. Concerning the samples prepared at T_S=200 and 500° C, they show fcc and polycrystalline structures, respectively and more intricate magnetic anisotropy patterns.     

Dual behaviors of magnetic CoxFe1−x (0≤x≤1) nanowires embedded in nanoporous with different diameters

Co_xFe_1−x nanowire arrays with various diameters and different composition were fabricated by ac electrodeposition using porous alumina template. Coercivity along the easy axis reaches to a maximum at 2330 Oe, for Co_xFe_1−x nanowires containing about 40 at% Co. The crystalline structure of the nanowires was concentration-independent and shows a bcc structure. The critical diameter for transition from coherent rotation to curling mode is 35 nm for CoFe containing less than 40 at% Co while it is 30 nm for those with more than 40 at% Co. Optimizing the magnetic properties of CoFe with different Co content was seen to be dependent on the diameter of nanowires. For 25 nm diameter, the optimum was shown below 50 at% Co while it was seen above 50 at% for nanowires with 50 nm diameter. The angular dependence of the coercivity with nanowires diameter were also studied.     

Ultraviolet emission properties of ZnO film with zinc deficiency by SS CVD

A-b axis orientation ZnO film on silicon (1 0 0) substrate has been prepared by a single source chemical vapor deposition technique. X-ray photoelectron spectroscopy results revealed that the film was very close to stoichiometry but with a small amount of zinc deficiency. Temperature-dependent (10-300 K) ultraviolet photoluminescence of the film was presented. Comparing the photon energy separation of the several groups in the near band edge ultraviolet luminescence bands, as well as the variation of the relative intensities and the shift of the luminescence lines at different temperatures, free-, bound-exciton and its assisted phonon emission were observed, which corresponded to the mechanism of the ultraviolet emission properties. A strong ultraviolet emission resulting from the recombination of free-exciton was observed at 300 K photoluminescence spectrum examined in atmosphere environment. Contrasted to the relatively weak ultraviolet emission of the film in vacuum, atmosphere environment was found to be an important contribution to the strong ultraviolet emission of the film.     

Nanocrystalline Sr2FeMoO6 prepared by citrate-gel method

Double perovskite Sr₂FeMoO₆ powders with small crystallite size have been synthesised with citrate-gel method. The starting solution pH was varied between 1.5 and 9.0 resulting in large differences in the phase composition and ordering of B^′/B^″ sites. The samples prepared at 975 °C had crystallite sizes under 40 nm whereas crystallite sizes of the samples prepared at 1050 °C were between 78 and 239 nm. The XRD patterns were refined with spacegroup I 4/m, which gave good results for both batches, although clearly better results were obtained with monoclinic P 2₁/n spacegroup for the 975 °C batch. The ordering and the saturation magnetization agreed well with each other after treatment at 1050 °C, but the samples prepared at 975 °C had a strongly reduced saturation magnetization from that given by the ordering.     

Electrical and magnetic properties of Ni-Cu-Si heterojunction prepared by the liquid phase epitaxy technique

Ni-Cu-Si heterojunction was prepared by the liquid phase epitaxy (LPE) technique. Two growth solutions containing Indium (In) with Cu pieces and In with Ni pieces were employed during the fabrication process. The as-formed junction was directly characterized by different techniques including scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and thin film X-ray diffraction (XRD) measurements. The current-voltage (I-V) characteristics of the Au/Ni/Cu/Si diode were found to be nonlinear, asymmetric, having a good rectification behavior with a very small leakage current of 0.003 μA at a reverse bias voltage of 2.0 V. The value of turn on voltage was located at 0.2 V. The magnetic properties were also evaluated at room temperature with a vibrating sample magnetometer. Systematic study of junction fabrication and characterization of such a heterosystem, comparison of the behavior of flat silicon and nanoporous silicon as substrates are presented and thoroughly discussed.     

Synthesis of Fe2O3 concentrations and sintering temperature on FTIR and magnetic susceptibility measured from 4 to 300 K of monolith silica gel prepared by sol–gel technique

Nano-crystalline ferric oxide was synthesized inside an amorphous silica matrix by the sol–gel method. The formation of ferric oxide can be detected, giving fine particles around 5–10 nm crystallite sizes calculated from win-fit program. This is associated with a specific role of the silica matrix, which facilitates the diffusion of the reacting cations, enhancing the ferric oxide formation. γ- to α- and/or ε-Fe₂O₃ transformations take place by increasing the Fe₂O₃ concentration for samples sintering at constant-heat treatment temperature. The dried monolith gel materials were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR), as well as by scanning electron microscopy (SEM). The magnetic susceptibility at zero-field cooling (M_ZFC) of the prepared samples was evaluated using superconducting quantum interference device (SQUID) magnetometer in temperature range from 4 to 300 K at 1 T.     

Protein imprinting and recognition via forming nanofilms on microbeads surfaces in aqueous media

In this paler, we present a technique of forming nanofilms of poly-3-aminophenylboronic acid (pAPBA) on the surfaces of polystyrene (PS) microbeads for proteins (papain and trypsin) in aqueous. Papain was chosen as a model to study the feasibility of the technique and trypsin as an extension. Obtained core-shell microbeads were characterized using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and BET methods. The results show that pAPBA formed nanofilms (60-100 nm in thickness) on the surfaces of PS microbeads. The specific surface area of the papain-imprinted beads was about 180 m² g⁻¹ and its pore size was 31 nm. These imprinted microbeads exhibit high recognition specificity and fast mass transfer kinetics. The specificity of these imprinted beads mainly originates from the spatial effect of imprinted sites. Because the protein-imprinted sites were located at, or close to, the surface, the imprinted beads have good site accessibility toward the template molecules. The facility of the imprinting protocol and the high recognition properties of imprinted microbeads make the approach an attractive solution to problems in the field of biotechnology.